A cross-layer scheme, namely ALOHA With Collision Resolution (ALOHA-CR), is proposed for high throughput wireless communications in a cellular scenario. Transmissions occur in a time-slotted ALOHA-type fashion but with an important difference: simultaneous transmissions of two users can be successful. If more than two users transmit in the same slot the collision cannot be resolved and retransmission is required. If only one user transmits, the transmitted packet is recovered with some probability, depending on the state of the channel. If two users transmit the collision is resolved and the packets are recovered by first over-sampling the collision signal and then exploiting independent information about the two users that is contained in the signal polyphase components. The ALOHA-CR throughput is derived under the infinite backlog assumption and also under the assumption of finite backlog. The contention probability is determined under these two assumptions in order to maximize the network throughput and maintain stability. Queuing delay analysis for network users is also conducted. The performance of ALOHA-CR is demonstrated on the Wireless Open Access Research Platform (WARP) test-bed containing five software defined radio nodes. Analysis and test-bed results indicate that ALOHA-CR leads to significant increase in throughput and reduction of service delays.
We consider a massive Internet of Things (IoT) scenario where indoor IoT devices access the network via optical wireless communication (OWC) IoT systems that relay data via a backhaul radio frequency (RF) low-power wide-area network (LP WAN). We propose a novel two-tier multi-rate Slotted ALOHA (SA) system model to design and analyse such hybrid OWC/RF networks. For a particular hybrid OWC/RF setup, we present an in-depth numerical investigation that provides insights into the proposed two-tier multi-rate hybrid OWC/RF SA system design.
We study the asymptotic performance of two multi-hop overlaid ad-hoc networks that utilize the same temporal, spectral, and spatial resources based on random access schemes. The primary network consists of Poisson distributed legacy users with density λ^{(p)} and the secondary network consists of Poisson distributed cognitive radio users with density λ^{(s)} = (λ^{(p)})^β (β>0, β\neq 1) that utilize the spectrum opportunistically. Both networks are decentralized and employ ALOHA medium access protocols where the secondary nodes are additionally equipped with range-limited perfect spectrum sens…
This paper introduces a protocol that distributively constructs a collision-free schedule for multi-hop packet radio networks in the presence of hidden terminals. As a preliminary step, each wireless station computes the schedule length after gathering information about the number of flows in its neighbourhood. Then, a combination of deterministic and random backoffs are used to reach a collision-free schedule. A deterministic backoff is used after successful transmissions and a random backoff is used otherwise. It is explained that the short acknowledgement control packets can easily result i…
We implement an IoT network the following way: one gateway, one or several intelligent (i.e., learning) objects, embedding the proposed solution, and a traffic generator that emulates radio interferences from many other objects. Intelligent objects communicate with the gateway with a wireless ALOHA-based protocol, which does not require any specific overhead for the learning. We model the network access as a discrete sequential decision making problem, and using the framework and algorithms from Multi-Armed Bandit (MAB) learning, we show that intelligent objects can improve their access to the…
In this paper we present a survey of existing prototypes dedicated to software defined radio. We propose a classification related to the architectural organization of the pro- totypes and provide some conclusions about the most promising architectures. This study should be useful for cognitive radio testbed designers who have to choose between many possible computing platforms. We also introduce a new cognitive radio testbed currently under construction and explain how this study have influenced the test-bed designers choices.
This paper addresses the radio interface problematic for MANET (Mobile Ad-hoc NETwork) applications. Here we propose to study the radio reconfigurability in order to provide a unique physical layer which is able to deal with all MANET applications. For implementing this reconfigurable physical layer, we propose to use Impulse Radio Ultra WideBand (IRUWB). This paper presents also our two level design approach for obtaining our reconfigurable IR-UWB receiver on FPGA (Field Programmable Gate Array).
Wireless systems using low-power wireless communication protocol are rapidly gain popularity in the license-free industrial scientific, and medical (ISM) frequency bands. One such emerging trend in ISM frequency bands is home automation. Historically, all the home devices were once unconnected, today are now being connected either by a wired or wireless connection. The low-power wireless communication protocols enable integration of all the digital home devices into a single system and enhance end user product experience. The rapid prototyping of these end user product using programmable radio…
This paper reports an implementation of the PHY specifications of the IEEE 802.15.4 standard for the frequency band 868 915 MHz on a Software Defined Radio (SDR) platform. This standard is defined for low power, low data rate and low cost wireless networks. These specifications are used by the Zigbee technology for various applications such as home automation, industry monitoring or medical surveillance. Several hardware PHY 868/915 MHz band IEEE 802.15.4 transceiver implementations have been already reported on ASIC and FPG [1] [2]. SDR offers one possibility to realize a transceiver with hig…
This paper presents the design and implementation of signaling splitting scheme in hyper-cellular network on a software defined radio platform. Hyper-cellular network is a novel architecture of future mobile communication systems in which signaling and data are decoupled at the air interface to mitigate the signaling overhead and allow energy efficient operation of base stations. On an open source software defined radio platform, OpenBTS, we investigate the feasibility of signaling splitting for GSM protocol and implement a novel system which can prove the proposed concept. Standard GSM handse…
This paper investigates the throughput for wireless network with full-duplex radios using stochastic geometry. Full-duplex (FD) radios can exchange data simultaneously with each other. On the other hand, the downside of FD transmission is that it will inevitably cause extra interference to the network compared to half-duplex (HD) transmission. In this paper, we focus on a wireless network of nodes with both HD and FD capabilities and derive and optimize the throughput in such a network. Our analytical result shows that if the network is adapting an ALOHA protocol, the maximal throughput is alw…
In this paper, we describe the design and implementation of D2D communication functionality for LTE. To our knowledge, this is the first such implementation that is compliant with the LTE Release 12 standard. In this paper, we design and demonstrate an experiment on mode selection between infrastructure mode and D2D communication mode in LTE networks. We implement our system on a software-defined radio SDR testbed, augmenting the open-source LTE eNodeB and UE implementation provided by the srsLTE software suite. Our measurements demonstrate the cell extension capabilities of D2D and quantify t…
Network slicing is a fundamental feature of 5G systems to partition a single network into a number of segregated logical networks, each optimized for a particular type of service, or dedicated to a particular customer or application. The realization of network slicing is particularly challenging in the Radio Access Network (RAN) part, where multiple slices can be multiplexed over the same radio channel and Radio Resource Management (RRM) functions shall be used to split the cell radio resources and achieve the expected behaviour per slice. In this context, this paper describes the key design a…
In this paper, an analysis is carried out for a method to mitigate the path loss through the dynamic spectrum access (DSA) method. The path loss is a major component which determines the QoS of a wireless link. Its effect is complemented by the presence of obstruction between the transmitter and receiver. The future cellular network (5G) focuses on operating with the millimeter-wave (mmW). In higher frequency, path loss can play a significant role in degrading the link quality due to higher attenuation. In a scenario, where the operating environment is changing dynamically, sudden degradation …
The radio access networks (RANs) need to support massive and diverse data traffic with limited spectrum and energy. To cope with this challenge, software-defined radio access network (SDRAN) architectures have been proposed to renovate the RANs. However, current researches lack the design and evaluation of network protocols. In this paper, we address this problem by presenting the protocol design and evaluation of hyper-cellular networks (HyCell), an SDRAN framework making base station (BS) operations globally resource-optimized and energy-efficient (GREEN). Specifically, we first propose a se…
Modern radio astronomy relies on very large amounts of data that need to be transferred between various parts of astronomical instruments, over distances that are often in the range of tens or hundreds of kilometres. The Square Kilometre Array (SKA) will be the world's largest radio telescope, data rates between its components will exceed Terabits per second. This will impose a huge challenge on its data transport system, especially with regard to power consumption. High-speed data transfers using modern off-the-shelf hardware may impose a significant load on the receiving system with respect …
This article discusses the available Software Defined Radios (SDRs), compatible software, message formats, and also shows how it is possible to do penetration tests using SDR for Bluetooth Low Energy (BLE) and ZigBee technologies.
NB-IoT is the 3GPP standard for machine-to-machine communications, recently finalized within LTE release 13. This article gives a brief overview about this new LTE-based radio access technology and presents a implementation developed using the srsLTE software radio suite. We also carry out a performance study in which we compare a theoretical analysis with experimental results obtained in our testbed. Furthermore, we provide some interesting details and share our experience in exploring one of the worldwide first commercial NB-IoT deployments.
Time-sensitive wireless networks are an important enabling building block for many emerging industrial Internet of Things (IoT) applications. Quick prototyping and evaluation of time-sensitive wireless technologies are desirable for R&D efforts. Software-defined radio (SDR), by allowing wireless signal processing on a personal computer (PC), has been widely used for such quick prototyping efforts. Unfortunately, because of the \textit{uncontrollable delay} between the PC and the radio board, SDR is generally deemed not suitable for time-sensitive wireless applications that demand communication…
Research conducted in LTE and 5G wireless communications systems uses common off-the-shelf hardware components and commercial software defined radio (SDR) hardware. One of the more popular SDR platforms is the Ettus USRP product line which uses the UHD driver and transport protocol framework. System performance can be increased using kernel bypass frameworks along with UHD. This paper investigates UHD with DPDK in an SDR environment using srslTE as the SDR application. We present measurement results using the iperf3 network performance application that show performance improvements when employ…
Cellular network-connected unmanned aerial vehicles (UAVs) experience different radio propagation conditions than radio nodes on the ground. Therefore, it has become critical to investigate the performance of aerial radios, both theoretically and through field trials. In this paper, we consider low-altitude aerial nodes that are served by an experimental cellular network. We provide a detailed description of the hardware and software components needed for establishing a broadband wireless testbed for UAV communications research using software radios. Results show that a testbed for innovation …
Applying high-speed real-time wireless technologies in industrial applications has the great potential to reduce the deployment and maintenance costs compared to their wired counterparts. Wireless technologies enhance the mobility and reduce the communication jitter and delay for mobile industrial equipment, such as mobile collaborative robots. Unfortunately, most existing wireless solutions employed in industrial fields either cannot support the desired high-speed communications or cannot guarantee deterministic, real-time performance. A more recent wireless technology, RT-WiFi, achieves a go…
Dramatic mobile data traffic growth has spurred a dense deployment of small cell base stations (SCBSs). Small cells enhance the spectrum efficiency and thus enlarge the capacity of mobile networks. Although SCBSs consume much less power than macro BSs (MBSs) do, the overall power consumption of a large number of SCBSs is phenomenal. As the energy harvesting technology advances, base stations (BSs) can be powered by green energy to alleviate the on-grid power consumption. For mobile networks with high BS density, traffic load balancing is critical in order to exploit the capacity of SCBSs. To f…
The concept of cross-layer optimization has been around for several years now. The primary goal of the cross-layer approach was to liberate the strict boundary between the layers of the traditional OSI protocol stack. This is to enable information flow between layers which then can be leveraged to optimize the network's performance across the layers. This concept has been of keen interest for tactical application as there is an overwhelming requirement to operate in a challenging and dynamic environment. The advent of software defined radios (SDR) accelerated the growth of this domain due to t…
As new use cases are emerging for unmanned aerial systems (UAS), advanced wireless communications technologies and systems need to be implemented and widely tested. This requires a flexible platform for development, deployment, testing and demonstration of wireless systems with ground and aerial nodes, enabling effective 3D mobile communications and networking. In this paper, we provide a comparative overview of software-defined radios (SDRs), with a specific focus on SDR hardware and software that can be used for aerial wireless experimentation and research. We discuss SDR hardware requiremen…
The article presents a method of organizing men-in-the-middle attack and penetration test on Bluetooth Low Energy devices and ZigBee packets using software define radio with sniffing and spoofing packets, capture and analysis techniques on wireless waves with the focus on Bluetooth. The paper contains the analysis of the latest scientific work in this area, provides a comparative analysis of SDRs and the rationale for the choice of hardware, gives the sequence of actions for collecting wireless data packets and data collection from ZigBee and BLE devices, and analyzes ways to improve captured …
Implementation of Zero-shot Semantic Communication on Software Defined Radio
Wireless Systems Laboratory, Wireless Networks Research Center（无线系统实验室，无线网络研究中心）；National Institute of Information and Communications Technology (NICT)（信息通信技术研究所）
Mobile Networks today comprise of multiple Radio Access Technologies (RATs), e.g., 4G LTE, Wireless Local Area Network (WLAN), and the upcoming 5G-New Radio (5G-NR). The access networks of these RATs are controlled by RAT-specific entities, e.g., the resource management function located inside an individual LTE eNB is used for the eNB control, or access controllers are used for controlling WLAN Access Points. Even in the 3GPP's 5G architecture, which has a common Core supporting multiple RATs, radio access related decisions are taken independently within individual RATs. Due to the fragmented …
Since J. Mitola's work in 1992, Software Defined Radios (SDRs) have been quite a hot topic in wireless systems research. Though many notable achievements were reported in the field, the scarcity of computational power on general purpose CPUs has always constrained their wide adoption in production environments. If conveniently applied within an SDR context, classical concepts known in computer science as space/time tradeoffs can be extremely helpful when trying to mitigate this problem. Inspired by and building on those concepts, this paper presents a novel SDR implementation technique which w…
5G New Radio (NR) is an emerging radio access technology, which is planned to succeed 4G Long Term Evolution (LTE) as global standard of cellular communications in the upcoming years. This paper considers a digital signal processing model and a software implementation of a complete transceiver chain of the Physical Uplink Shared Channel (PUSCH) defined by the version 15 of the 3GPP standard, consisting of both baseband transmitter and receiver chains on a physical layer level. The BLER performance of the prototype system implementation under AWGN and Rayleigh fading channel conditions is evalu…
The Cloud radio access network (C-RAN) offers a revolutionary approach to cellular network deployment, management and evolution. Advances in software-defined radio (SDR) and networking technology, moreover, enable delivering software-defined everything through the Cloud. Resources will be pooled and dynamically allocated leveraging abstraction, virtualization, and consolidation techniques; processes will be automated using common application programming interfaces; and network functions and services will be programmatically provided through an orchestrator. OOCRAN, oocran.dynu.com, is a softwa…
To meet the growing local and distributed computing needs, the cloud is now descending to the network edge and sometimes to user equipments. This approach aims at distributing computing, data processing, and networking services closer to the end users. Instead of concentrating data and computation in a small number of large clouds, many edge systems are envisioned to be deployed close to the end users or where computing and intelligent networking can best meet user needs. In this paper, we go further converging such massively distributed computing systems with multiple radio accesses. We propo…
Mobility management is the key feature of cellular networks. When integrating unmanned aerial vehicles (UAVs) into cellular networks, their cell association needs to be carefully managed for coexistence with other cellular users. UAVs move in three dimensions and may traverse several cells on their flight path, and so may be subject to several handovers. In order to enable research on mobility management with UAV users, this paper describes the design, implementation, and testing methodology for handover experiments with aerial users. We leverage software-defined radios (SDRs) and implement a …
Software defined radio is a widely accepted paradigm for design of reconfigurable modems. The continuing march of Moore's law makes real-time signal processing on general purpose processors feasible for a large set of waveforms. Data rates in the low Mbps can be processed on low-power ARM processors, and much higher data rates can be supported on large x86 processors. The advantages of all-software development (vs. FPGA/DSP/GPU) are compelling: much wider pool of talent, lower development time and cost, and easier maintenance and porting. However, very high-rate systems (above 100 Mbps) are st…
Software-defined Radio (SDR) is a programmable transceiver with the capability of operating various wireless communication protocols without the need to change or update the hardware. Progress in the SDR field has led to the escalation of protocol development and a wide spectrum of applications, with more emphasis on programmability, flexibility, portability, and energy efficiency, in cellular, WiFi, and M2M communication. Consequently, SDR has earned a lot of attention and is of great significance to both academia and industry. SDR designers intend to simplify the realization of communication…
More and more emerging Internet of Things (IoT) applications involve status updates, where various IoT devices monitor certain physical processes and report their latest statuses to the relevant information fusion nodes. A new performance measure, termed the age of information (AoI), has recently been proposed to quantify the information freshness in time-critical IoT applications. Due to a large number of devices in future IoT networks, the decentralized channel access protocols (e.g. random access) are preferable thanks to their low network overhead. Built on the AoI concept, some recent eff…
Terrestrial and satellite communication networks often rely on two-hop wireless architectures with an access channel followed by backhaul links. Examples include Cloud-Radio Access Networks (C-RAN) and Low-Earth Orbit (LEO) satellite systems. Furthermore, communication services characterized by the coexistence of heterogeneous requirements are emerging as key use cases. This paper studies the performance of critical service (CS) and non-critical service (NCS) for Internet of Things (IoT) systems sharing a grant-free channel consisting of radio access and backhaul segments. On the radio access …
This paper presents our methodology and toolbox that allows analyzing the radio access network security of laboratory and commercial 4G and future 5G cellular networks. We leverage a free open-source software suite that implements the LTE UE and eNB enabling real-time signaling using software radio peripherals. We modify the UE software processing stack to act as an LTE packet collection and examination tool. This is possible because of the openness of the 3GPP specifications. Hence, we are able to receive and decode LTE downlink messages for the purpose of analyzing potential security problem…
Dynamic resource allocation plays a critical role in the next generation of intelligent wireless communication systems. Machine learning has been leveraged as a powerful tool to make strides in this domain. In most cases, the progress has been limited to simulations due to the challenging nature of hardware deployment of these solutions. In this paper, for the first time, we design and deploy deep reinforcement learning (DRL)-based power control agents on the GPU embedded software defined radios (SDRs). To this end, we propose an end-to-end framework (MR-iNet Gym) where the simulation suite an…
The proliferation of wireless devices and their ever increasing influence on our day-to-day life is very evident and seems irreplaceable. This exponential growth in demand, both in terms of the number of devices and Quality of Service (QoS) had spawned the concept of cross-layer optimization several years ago. The primary goal of the cross-layer approach was to liberate the strict boundary between the layers of the traditional Open Systems Interconnection (OSI) protocol stack. The initial decade focused on establishing the theoretical feasibility of this revolutionary concept and gauging the e…
