We consider multiple-input multiple-output (MIMO) radar systems with widely-spaced antennas. Such antenna configuration facilitates capturing the inherent diversity gain due to independent signal dispersion by the target scatterers. We consider a new MIMO radar framework for detecting a target that lies in an unknown location. This is in contrast with conventional MIMO radars which break the space into small cells and aim at detecting the presence of a target in a specified cell. We treat this problem through offering a novel composite hypothesis testing framework for target detection when (i) one or more parameters of the target are unknown and we are interested in estimating them, and (ii) only a finite number of observations are available. The test offered optimizes a metric which accounts for both detection and estimation accuracies. In this paper as the parameter of interest we focus on the vector of time-delays that the waveforms undergo from being emitted by the transmit antennas until being observed by the receive antennas. The analytical and empirical results establish that for the proposed joint target detection and time-delay estimation framework, MIMO radars exhibit significant gains over phased-array radars for extended targets which consist of multiple independent scatterers. For point targets modeled as single scatterers, however, the detection/estimation accuracies of MIMO and phased-array radars for this specific setup (joint target detection and time-delay estimation) are comparable.
Spectrum sharing between radars and cellular systems is an emerging area of research. In this paper, we model channel between a seaborne MIMO radar and MIMO cellular system. We model a 2D channel to capture the azimuth aspect of the spectrum sharing scenario. Our channel modeling methodology allows MIMO radar to place accurate nulls in the azimuth location of base stations (BS), thus, protecting them from harmful radar interference. We use a projection based approach, where radar waveform is projected onto null space of channel, for mitigating radar interference to BSs. This is also known as a…
We propose a new technique for multiple-input multiple-output (MIMO) radar with colocated antennas which we call phased-MIMO radar. The new technique enjoys the advantages of MIMO radar without sacrificing the main advantage of phased-array radar which is the coherent processing gain at the transmitting side. The essence of the proposed technique is to partition the transmitting array into a number of subarrays that are allowed to overlap. Then, each subarray is used to coherently transmit a waveform which is orthogonal to the waveforms transmitted by other subarrays. Coherent processing gain …
This paper explores an overlapped-multiple-input multiple-output (MIMO) antenna architecture and a spectrum sharing algorithm via null space projection (NSP) for radar-communications coexistence. In the overlapped-MIMO architecture, the transmit array of a collocated MIMO radar is partitioned into a number of subarrays that are allowed to overlap. Each of the antenna elements in these subarrays have signals orthogonal to each other and to the elements of the other subarrays. The proposed architecture not only improves sidelobe suppression to reduce interference to communications system, but al…
A new approach is proposed, namely CSSF MIMO radar, which applies the technique of step frequency (SF) to compressive sensing (CS) based multi-input multi-output (MIMO) radar. The proposed approach enables high resolution range, angle and Doppler estimation, while transmitting narrowband pulses. The problem of joint angle-Doppler-range estimation is first formulated to fit the CS framework, i.e., as an L1 optimization problem. Direct solution of this problem entails high complexity as it employs a basis matrix whose construction requires discretization of the angle-Doppler-range space. Since h…
Multiple-input multiple-output (MIMO) radars offer higher resolution, better target detection, and more accurate target parameter estimation. Due to the sparsity of the targets in space-velocity domain, we can exploit Compressive Sensing (CS) to improve the performance of MIMO radars when the sampling rate is much less than the Nyquist rate. In distributed MIMO radars, block CS methods can be used instead of classical CS ones for more performance improvement, because the received signal in this group of MIMO radars is a block sparse signal in a basis. In this paper, two new methods are propose…
Sharing radar spectrum with communication systems is an emerging area of research. Deploying commercial wireless communication services in radar bands give wireless operators the much needed additional spectrum to meet the growing bandwidth demands. However, to enable spectrum sharing between these two fundamentally different systems interference concerns must be addressed. In order to assess interference concerns we design a three-dimensional (3D) channel model between radar and cellular base stations (BSs) in which the radar uses a two-dimensional (2D) antenna array and the BS uses a one-dim…
In this paper, we propose MIMO OFDM radar with sufficient cyclic prefix (CP), where all OFDM pulses transmitted from different transmitters share the same frequency band and are orthogonal to each other for every subcarrier in the discrete frequency domain. The orthogonality is not affected by time delays from transmitters. Thus, our proposed MIMO OFDM radar has the same range resolution as single transmitter radar and achieves full spatial diversity. Orthogonal designs are used to achieve this orthogonality across the transmitters, with which it is only needed to design OFDM pulses for the fi…
In this paper, we propose a cyclic prefix (CP) based MIMO-OFDM range reconstruction method and its corresponding MIMO-OFDM waveform design for co-located MIMO radar systems. Our proposed MIMO-OFDM waveform design achieves the maximum signal-to-noise ratio (SNR) gain after the range reconstruction and its peak-to-average power ratio (PAPR) in the discrete time domain is also optimal, i.e., 0dB, when Zadoff-Chu sequences are used in the discrete frequency domain as the weighting coefficients for the subcarriers. We also investigate the performance when there are transmit and receive digital beam…
In this paper, we derive an ambiguity function (AF) for the transmit beamspace (TB)-based multipleinput multiple-output (MIMO) radar for the case of far-field targets and narrow-band waveforms. The effects of transmit coherent processing gain and waveform diversity are incorporated into the AF definition. To cover all the phase information conveyed by different factors, we introduce the equivalent transmit phase centers. The newly defined AF serves as a generalized AF form for which the phased-array (PA) and traditional MIMO radar AFs are important special cases. We establish relationships amo…
Multiple-input multiple-output (MIMO) radar systems have been shown to achieve superior resolution as compared to traditional radar systems with the same number of transmit and receive antennas. This paper considers a distributed MIMO radar scenario, in which each transmit element is a node in a wireless network, and investigates the use of compressive sampling for direction-of-arrival (DOA) estimation. According to the theory of compressive sampling, a signal that is sparse in some domain can be recovered based on far fewer samples than required by the Nyquist sampling theorem. The DOA of tar…
To meet the growing spectrum demands, future cellular systems are expected to share the spectrum of other services such as radar. In this paper, we consider a network multiple-input multiple-output (MIMO) with partial cooperation model where radar stations cooperate with cellular base stations (BS)s to deliver messages to intended mobile users. So the radar stations act as BSs in the cellular system. However, due to the high power transmitted by radar stations for detection of far targets, the cellular receivers could burnout when receiving these high radar powers. Therefore, we propose a new …
In this letter, we consider the coexistence and spectrum sharing between downlink multi-user multiple-input-multiple-output (MU-MIMO) communication and a MIMO radar. For a given performance requirement of the downlink communication system, we design the transmit beamforming such that the detection probability of the radar is maximized. While the original optimization problem is non-convex, we exploit the monotonically increasing relationship of the detection probability with the non-centrality parameter of the resulting probability distribution to obtain a convex lower-bound optimization. The …
Multiple input multiple output (MIMO) radar exhibits several advantages with respect to traditional radar array systems in terms of flexibility and performance. However, MIMO radar poses new challenges for both hardware design and digital processing. In particular, achieving high azimuth resolution requires a large number of transmit and receive antennas. In addition, the digital processing is performed on samples of the received signal, from each transmitter to each receiver, at its Nyquist rate, which can be prohibitively large when high resolution is needed. Overcoming the rate bottleneck, …
In a typical MIMO radar scenario, transmit nodes transmit orthogonal waveforms, while each receive node performs matched filtering with the known set of transmit waveforms, and forwards the results to the fusion center. Based on the data it receives from multiple antennas, the fusion center formulates a matrix, which, in conjunction with standard array processing schemes, such as MUSIC, leads to target detection and parameter estimation. In MIMO radars with compressive sensing (MIMO-CS), the data matrix is formulated by each receive node forwarding a small number of compressively obtained samp…
Recently proposed multiple input multiple output radars based on matrix completion (MIMO-MC) employ sparse sampling to reduce the amount of data that need to be forwarded to the radar fusion center, and as such enable savings in communication power and bandwidth. This paper proposes designs that optimize the sharing of spectrum between a MIMO-MC radar and a communication system, so that the latter interferes minimally with the former. First, the communication system transmit covariance matrix is designed to minimize the effective interference power (EIP) to the radar receiver, while maintainin…
Future wireless communication systems are envisioned to share radio frequency (RF) spectrum, with other services such as radars, in order to meet the growing spectrum demands. In this paper, we consider co-channel spectrum sharing between cellular systems and radars. We address the problem of target detection by radars that are subject to shape its waveform in a way that it does not cause interference to cellular systems. We consider a multiple-input multiple-output (MIMO) radar and a MIMO cellular communication system with $\mc K$ base stations (BS). We propose a spectrum sharing algorithm wh…
The authors recently proposed a MIMO radar system that is implemented by a small wireless network. By applying compressive sensing (CS) at the receive nodes, the MIMO radar super-resolution can be achieved with far fewer observations than conventional approaches. This previous work considered the estimation of direction of arrival and Doppler. Since the targets are sparse in the angle-velocity space, target information can be extracted by solving an l1 minimization problem. In this paper, the range information is exploited by introducing step frequency to MIMO radar with CS. The proposed appro…
In this paper, considering multiple interference regions simultaneously, an optimal antenna deployment problem for distributed Multi-Input Multi-Output (MIMO) radar is investigated. The optimal antenna deployment problem is solved by proposing an antenna deployment method based on Multi-Objective Particle Swarm Optimization (MOPSO). Firstly, we construct a multi-objective optimization problem for MIMO radar antenna deployment by choosing the interference power densities of different regions as objective functions. Then, to obtain the optimal deployment result without wasting time and computati…
We present the design and hardware implementation of a radar prototype that demonstrates the principle of a sub-Nyquist collocated multiple-input multiple-output (MIMO) radar. The setup allows sampling in both spatial and spectral domains at rates much lower than dictated by the Nyquist sampling theorem. Our prototype realizes an X-band MIMO radar that can be configured to have a maximum of 8 transmit and 10 receive antenna elements. We use frequency division multiplexing (FDM) to achieve the orthogonality of MIMO waveforms and apply the Xampling framework for signal recovery. The prototype al…
Enabled by the advancement in radio frequency technologies, the convergence of radar and communication systems becomes increasingly promising and is envisioned as a key feature of future 6G networks. Recently, the frequency-hopping (FH) MIMO radar is introduced to underlay dual-function radar-communication (DFRC) systems. Superior to many previous radar-centric DFRC designs, the symbol rate of FH-MIMO radar-based DFRC (FH-MIMO DFRC) can exceed the radar pulse repetition frequency. However, many practical issues, particularly those regarding effective data communications, are unexplored/unsolve…
In colocated multiple-input multiple-output (MIMO) radar using compressive sensing (CS), a receive node compresses its received signal via a linear transformation, referred to as measurement matrix. The samples are subsequently forwarded to a fusion center, where an L1-optimization problem is formulated and solved for target information. CS-based MIMO radar exploits the target sparsity in the angle-Doppler-range space and thus achieves the high localization performance of traditional MIMO radar but with many fewer measurements. The measurement matrix is vital for CS recovery performance. This …
Co-Designing Statistical MIMO Radar and In-band Full-Duplex Multi-User MIMO Communications -- Part II: Joint Precoder, Radar Code, and Receive Filters Design
A distributed MIMO radar is considered, in which the transmit and receive antennas belong to nodes of a small scale wireless network. The transmit waveforms could be uncorrelated, or correlated in order to achieve a desirable beampattern. The concept of compressive sampling is employed at the receive nodes in order to perform direction of arrival (DOA) estimation. According to the theory of compressive sampling, a signal that is sparse in some domain can be recovered based on far fewer samples than required by the Nyquist sampling theorem. The DOAs of targets form a sparse vector in the angle …
A joint robust transmit/receive adaptive beamforming for multiple-input multipleoutput (MIMO) radar based on probability-constrained optimization approach is developed in the case of Gaussian and arbitrary distributed mismatch present in both the transmit and receive signal steering vectors. A tight lower bound of the probability constraint is also derived by using duality theory. The formulated probability-constrained robust beamforming problem is nonconvex and NP-hard. However, we reformulate its cost function into a bi-quadratic function while the probability constraint splits into transmit…
Multiple-input multiple-output (MIMO) radar is a relatively new concept in the field of radar signal processing. Many novel MIMO radar waveforms have been developed by considering various performance metrics and constraints. In this paper, we show that finite alphabet constant-envelope (FACE) quadrature-pulse shift keying (QPSK) waveforms can be designed to realize a given covariance matrix by transforming a constrained nonlinear optimization problem into an unconstrained nonlinear optimization problem. In addition, we design QPSK waveforms in a way that they don't cause interference to a cell…
This paper presents an analysis of target localization accuracy, attainable by the use of MIMO (Multiple-Input Multiple-Output) radar systems, configured with multiple transmit and receive sensors, widely distributed over a given area. The Cramer-Rao lower bound (CRLB) for target localization accuracy is developed for both coherent and non-coherent processing. Coherent processing requires a common phase reference for all transmit and receive sensors. The CRLB is shown to be inversely proportional to the signal effective bandwidth in the non-coherent case, but is approximately inversely proport…
We present a cognitive prototype that demonstrates a colocated, frequency-division-multiplexed, multiple-input multiple-output (MIMO) radar which implements both temporal and spatial sub-Nyquist sampling. The signal is sampled and recovered via the Xampling framework. Cognition is due to the fact that the transmitter adapts its signal spectrum by emitting only those subbands that the receiver samples and processes. Real-time experiments demonstrate sub-Nyquist MIMO recovery of target scenes with 87.5% spatio-temporal bandwidth reduction and signal-to-noise-ratio of -10 dB.
A multiple input, multiple output (MIMO) radar emits probings signals with multiple transmit antennas and records the reflections from targets with multiple receive antennas. Estimating the relative angles, delays, and Doppler shifts from the received signals allows to determine the locations and velocities of the targets. Standard approaches to MIMO radar based on digital matched filtering or compressed sensing only resolve the angle-delay-Doppler triplets on a $(1/(N_T N_R), 1/B,1/T)$ grid, where $N_T$ and $N_R$ are the number of transmit and receive antennas, $B$ is the bandwidth of the pro…
Multiple-input multiple-output (MIMO) radar has become a thriving subject of research during the past decades. In the MIMO radar context, it is sometimes more accurate to model the radar clutter as a non-Gaussian process, more specifically, by using the spherically invariant random process (SIRP) model. In this paper, we focus on the estimation and performance analysis of the angular spacing between two targets for the MIMO radar under the SIRP clutter. First, we propose an iterative maximum likelihood as well as an iterative maximum a posteriori estimator, for the target's spacing parameter e…
We study compressive sensing in the spatial domain to achieve target localization, specifically direction of arrival (DOA), using multiple-input multiple-output (MIMO) radar. A sparse localization framework is proposed for a MIMO array in which transmit and receive elements are placed at random. This allows for a dramatic reduction in the number of elements needed, while still attaining performance comparable to that of a filled (Nyquist) array. By leveraging properties of structured random matrices, we develop a bound on the coherence of the resulting measurement matrix, and obtain conditions…
New generation of radar systems will need to coexist with other radio frequency (RF) systems, anticipating their behavior and reacting appropriately to avoid interference. In light of this requirement, this paper designs, implements, and evaluates the performance of phase-only sequences (with constant power) for intelligent spectrum utilization using the custom built cognitive Multiple Input Multiple Output (MIMO) radar prototype. The proposed transmit waveforms avoid the frequency bands occupied by narrowband interferers or communication links, while simultaneously have a small cross-correlat…
A MIMO radar system is proposed for obtaining angle and Doppler information on potential targets. Transmitters and receivers are nodes of a small scale wireless network and are assumed to be randomly scattered on a disk. The transmit nodes transmit uncorrelated waveforms. Each receive node applies compressive sampling to the received signal to obtain a small number of samples, which the node subsequently forwards to a fusion center. Assuming that the targets are sparsely located in the angle- Doppler space, based on the samples forwarded by the receive nodes the fusion center formulates an l1-…
One of the trends that is gaining more and more importance in the field of beyond-5G and 6G wireless communication systems is the investigation on systems that jointly perform communication and sensing of the environment. This paper proposes to use a base station (BS), that we call \textit{radar-BS}, equipped with a large-scale antenna array to execute, using the same frequency range, communication with mobile users and sensing/surveillance of the surrounding environment through radar scanning. The massive antenna array can indeed both operate as a MIMO radar with co-located antennas -- transm…
In this paper, we propose a two-dimensional (2D) joint transmit array interpolation and beamspace design for planar array mono-static multiple-input-multiple-output (MIMO) radar for direction-of-arrival (DOA) estimation via tensor modeling. Our underlying idea is to map the transmit array to a desired array and suppress the transmit power outside the spatial sector of interest. In doing so, the signal-tonoise ratio is improved at the receive array. Then, we fold the received data along each dimension into a tensorial structure and apply tensor-based methods to obtain DOA estimates. In addition…
In this paper we consider the uplink of a massive MIMO communication system using 5G New Radio-compliant multiple access, which is to co-exist with a radar system using the same frequency band. We propose a system model taking into account the reverberation (clutter) produced by the radar system at the massive MIMO receiver. Then, we propose several linear receivers for uplink data-detection, ranging by the simple channel-matched beamformer to the zero-forcing and linear minimum mean square error receivers for clutter disturbance rejection. Our results show that the clutter may have a strong e…
In this study, the hybrid Cramer-Rao bound (CRB) is developed for target localization, to establish the sensitivity of the estimation mean-square error (MSE) to the level of phase synchronization mismatch in coherent Multiple-Input Multiple-Output (MIMO) radar systems with widely distributed antennas. The lower bound on the MSE is derived for the joint estimation of the vector of unknown parameters, consisting of the target location and the mismatch of the allegedly known system parameters, i.e., phase offsets at the radars. Synchronization errors are modeled as being random and Gaussian. A cl…
In this paper, we consider the design of a multiple-input multiple-output (MIMO) transmitter which simultaneously functions as a MIMO radar and a base station for downlink multiuser communications. In addition to a power constraint, we require the covariance of the transmit waveform be equal to a given optimal covariance for MIMO radar, to guarantee the radar performance. With this constraint, we formulate and solve the signal-to-interference-plus-noise ratio (SINR) balancing problem for multiuser transmit beamforming via convex optimization. Considering that the interference cannot be complet…
In colocated compressive sensing MIMO radar, the measurement matrix is specified by antenna placement. To guarantee an acceptable recovery performance, this measurement matrix should satisfy certain properties, e.g., a small coherence. Prior work in the literature often employs randomized placement algorithms which optimize the prior distribution of antenna locations. The performance of these algorithms is suboptimal, as they can be easily enhanced via expurgation. In this paper, we suggest an iterative antenna placement algorithm which determines the antenna locations deterministically. The p…
Subspace methods are essential to high-resolution environment sensing in the emerging unmanned systems, if further combined with the millimeter-wave (mm-Wave) massive multi-input multi-output (MIMO) technique. The estimation of signal/noise subspace, as one critical step, is yet computationally complex and presents a particular challenge when developing high-resolution yet low-complexity automotive radars. In this work, we develop a fast randomized-MUSIC (R-MUSIC) algorithm, which exploits the random matrix sketching to estimate the signal subspace via approximated computation. Our new approac…
A critical task of a radar receiver is data association, which assigns radar target detections to target filter tracks. Motivated by its importance, this paper introduces the problem of jointly designing multiple-input multiple-output (MIMO) radar transmit beam patterns and the corresponding data association schemes. We show that the coupling of the beamforming and the association subproblems can be conveniently parameterized by what we term an ambiguity graph, which prescribes if two targets are to be disambiguated by the beamforming design or by the data association scheme. The choice of amb…
In this paper, the problems of simultaneously detecting and localizing multiple targets are considered for noncoherent multiple-input multiple-output (MIMO) radar with widely separated antennas. By assuming a prior knowledge of target number, an optimal solution to this problem is presented first. It is essentially a maximum-likelihood (ML) estimator searching parameters of interest in a high dimensional space. However, the complexity of this method increases exponentially with the number G of targets.Besides, without the prior information of the number of targets, a multi-hypothesis testing s…
A fully-digital wideband joint communication-radar (JCR) with a multiple-input-multiple-output (MIMO) architecture at the millimeter-wave (mmWave) band will enable high joint communication and radar performance with enhanced design flexibility. A quantized receiver with few-bit analog-to-digital converters (ADCs) will enable a practical JCR solution with reduced power consumption for futuristic portable devices and autonomous vehicles. In this paper, we present a joint communication-radar proof-of-concept platform, named JCR70, to evaluate and demonstrate the performance of these JCR systems u…
In this work we consider a multiple-input multiple-output (MIMO) dual-function radar-communication (DFRC) system, which senses multiple spatial directions and serves multiple users. Upon resorting to an orthogonal frequency division multiplexing (OFDM) transmission format and a differential phase shift keying (DPSK) modulation, we study the design of the radiated waveforms and of the receive filters employed by the radar and the users. The approach is communication-centric, in the sense that a radar-oriented objective is optimized under constraints on the average transmit power, the power leak…
This paper considers the uplink of a massive MIMO communication system using 5G New Radio-compliant multiple access, which is to co-exist with a radar system using the same frequency band. A system model taking into account the reverberation (clutter) produced by the radar system onto the massive MIMO receiver is proposed. In this scenario, several receivers for uplink channel estimation and data detection are proposed, ranging from the simple channel-matched beamformer to the zero-forcing and linear minimum mean square error receivers for clutter disturbance rejection, under the two opposite …
The problem of joint design of transmit waveforms and receive filters is desirable in many application scenarios of multiple-input multiple-output (MIMO) radar systems. In this paper, the joint design problem is investigated under the signal-to-interference-plus-noise ratio (SINR) performance metric, in which case the problem is formulated to maximize the SINR at the receiver side subject to some practical transmit waveform constraints. A numerical algorithm is proposed for problem resolution based on the manifold optimization method, which has been shown to be powerful and flexible to address…
It is a fundamental problem to analyse the performance bound of multiple-input multiple-output (MIMO) dual-functional radar-communication (DFRC) systems. To this end, we derive a performance bound on the communication function under a constraint on radar performance. To facilitate the analysis, we consider a toy example, in which there is only one down-link user with a single receive antenna and one radar target. In such a simplified case, we obtain an analytical expression for the performance bound and the corresponding waveform design strategy to achieve the bound. The results reveal a trade…
In dual-functional communication-radar systems, common radio frequency (RF) signals are used for both communication and detection. For better compatibility with existing communication systems, we adopt multiple-input multiple-output (MIMO) orthogonal frequency division multiplexing (OFDM) signals as integrated signals and investigate the estimation performance of MIMO-OFDM signals. We first analyze the Cramer-Rao lower bound (CRLB) of parameters estimation. Then, transmit powers over different subcarriers are optimized to achieve the best tradeoff between transmission rate and estimation perfo…
We address the problem of tensor decomposition in application to direction-of-arrival (DOA) estimation for transmit beamspace (TB) multiple-input multiple-output (MIMO) radar. A general 4-order tensor model that enables computationally efficient DOA estimation is designed. Whereas other tensor decomposition-based methods treat all factor matrices as arbitrary, the essence of the proposed DOA estimation method is to fully exploit the Vandermonde structure of the factor matrices to take advantage of the shift-invariance between and within different subarrays. Specifically, the received signal of…
We analyze a multiple-input multiple-output (MIMO) radar model and provide recovery results for a compressed sensing (CS) approach. In MIMO radar different pulses are emitted by several transmitters and the echoes are recorded at several receiver nodes. Under reasonable assumptions the transformation from emitted pulses to the received echoes can approximately be regarded as linear. For the considered model, and many radar tasks in general, sparsity of targets within the considered angle-range-Doppler domain is a natural assumption. Therefore, it is possible to apply methods from CS in order t…
Since the seminal paper by Marzetta from 2010, the Massive MIMO paradigm in communication systems has changed from being a theoretical scaled-up version of MIMO, with an infinite number of antennas, to a practical technology. Its key concepts have been adopted in the 5G new radio standard and base stations, where $64$ fully-digital transceivers have been commercially deployed. Motivated by these recent developments, this paper considers a co-located MIMO radar with $M_T$ transmitting and $M_R$ receiving antennas and explores the potential benefits of having a large number of virtual spatial an…
