We report on the experimental investigation of a high-frequency
(1MHz - 1.8GHz) dielectric dispersion in unpoled and poled
Pb(Zr,Ti)O3 ceramics. Two overlapping loss peaks could be revealed in the dielectric spectrum. The linear dependence between the lower-frequency peak position and average grain size D, which holds for D< 10mkm, indicates that the corresponding polarization mechanism originates from piezoelectric resonances of grains. The intensity of the higher-frequency peak is drastically reduced by poling. It is thus proposed that this loss peak is related to domain-wall contribution to the dielectric dispersion.
The piezoelectric face-shear (d36) mode may be the most useful shear mode in piezoelectrics, while currently this mode can only exist in single crystals of specific point groups and cut directions. Theoretically the d36 coefficient vanishes in piezoelectric ceramics because of its transversally isotropic symmetry . In this work, we modified the symmetry of poled PZT ceramics from transversally isotropic to orthogonal through ferroelastic domain switching by applying a high lateral stress along the "2" direction and holding the stress for several hours. After removing the compression, the piezo…
Many ferroelectric devices are based on doped lead zirconate titanate (PZT) ceramics with compositions near the morphotropic phase boundary (MPB), at which the relevant material's properties approach their maximum. Based on a synchrotron x-ray diffraction study of MPB PZT, bulk fatigue is unambiguously found to arise from a less effective field induced tetragonal-to-monoclinic transformation, at which the degradation of the polarization flipping is detected by a less intense and more diffuse anomaly in the atomic displacement parameter of lead. The time dependence of the ferroelectric response…
The fundamental shear horizontal (SH0) wave in plate-like structures is extremely useful for non-destructive testing (NDT) and structural health monitoring (SHM) as it is non-dispersive. However, currently the SH0 wave is usually excited by electromagnetic acoustic transducers (EMAT) whose energy conversion efficiency is fairly low. The face-shear (d36) mode piezoelectrics is more promising for SH0 wave excitation but this mode cannot appear in conventional piezoelectric ceramics. Recently, by modifying the symmetry of poled PbZr1-xTixO3 (PZT) ceramics via ferroelastic domain engineering, we r…
Layered ferromagnetic-piezoelectric composites show mechanical strain mediated electromagnetic coupling. Here we discuss dielectric and piezoelectric properties of ferrite-lead zirconate titanate (PZT) and lanthanum manganite-PZT samples. Results of our investigations on dielectric and pyroelectric properties of multilayer ferromagnetic-piezoelectric are presented here. Lead zircinate-titanate PbZrxTi1-xO3 (PZT) was used for the piezoelectric phase in all the structures. The following materials were used for the ferromagnetic component: nickel-zinc ferrites Ni0.9Zn 0.1Fe2O4 (NFO1) and Ni0.8Zn0…
Results presented in this article demonstrate importance of taking into account such a phenomenon as the solid solution decomposition at the boundaries separating coexisting phases in lead-zirconate-titanate-based solid solutions with compositions belonging to the morphotropic boundary region of the "temperature-composition" phase diagram. It is shown that in the local decomposition of solid solutions in the vicinity of the boundaries separating the tetragonal and rhombohedral phases in lead-zirconate-titanate-based solid solutions lead to the changes of the chemical composition of the solid s…
The structure and dielectric properties of 6% $\rm{Sr}^{2+}$-substituted, modified Lead Zirconium Titanate (PZT) piezoelectric ceramic, with composition $[\rm{Pb}_{0.94}\rm{Sr}_{0.06}][(\rm{Mn}_{1/3}\rm{Sb}_{2/3})_{0.05}(\rm{Zr}_{0.54}\rm{Ti}_{0.46})_{0.95}]O_3$ and lead manganese antimonite as an additional dopant, synthesized by ceramic route have been investigated in a frequency range from 50Hz to 1MHz and in a temperature range between room temperature and 633K. The scanning electron micrograph of the sample taken at the room temperature confirms the formation of a fairly homogenous struct…
Magnetoelectric interactions in bilayers of magnetostrictive and piezoelectric phases are mediated by mechanical deformation. Here we discuss the theory and companion data for magnetoelectric (ME) coupling at electromechanical resonance (EMR) in a ferrite-lead zirconate titanate (PZT) bilayer. Estimated ME voltage coefficient versus frequency profiles for nickel, cobalt, or lithium ferrite and PZT reveal a giant ME effect at EMR with the highest coupling expected for cobalt ferrite-PZT. Measurements of resonance ME coupling have been carried out on layered and bulk composites of nickel ferrite…
Temperature dependent structural changes in a nearly pure monoclinic phase composition (x=0.525) of Pb(Zr_xTi_1-x)O_3 (PZT) have been investigated using Rietveld analysis of high-resolution synchrotron powder x-ray diffraction data and correlated with changes in the dielectric constant and planar electromechanical coupling coefficient. Our results show that the intrinsic piezoelectric response of the tetragonal phase of PZT is higher than that of the monoclinic phase. It is also shown that the high piezoelectric response of PZT may be linked with an anomalous softening of the elastic modulus (…
Piezoelectric PZT solid solutions were studied as a function of pressure and temperature. Moderate pressure is found to induce phase transitions to monoclinic phases (Cm,Cc) for Ti-rich PZT, which are the same ferroelectric phases responsible for the high piezoelectric properties of the MPB. The following transformation sequence P4mm -> Cm -> Cc -> F1 -> F-1 was identified upon increasing pressure. Compression behaviour is dominated by: (1) a rotation and a reduction of the spontaneouspolarization and (2) octahedral tilting leading to unit cell doubling. Future studies as a function of pressur…
Recent developments in piezoelectric films have heightened the need for the reliable methods to correctly characterize their piezoelectric coefficients. Here, we demonstrate that capacitive displacement method can be used to determine longitudinal piezoelectric coefficients in both bulk and thin film of piezoelectric materials reliably and simply. Our technique allows accurate detection of elastic displacement at a level of 2 pm. This achievement is of great interest and significance for the development of piezoelectric integration technology in modern smartdevices.
It is shown that the phase angle of the third harmonic of polarization response (delta3) is very sensitive to the ageing state of hard, Fe-doped lead zirconate titanate [Pb(Zr,Ti)O3 or PZT] ceramics and may thus provide rich information on processes responsible for ageing in hard ferroelectrics. When hard PZT ceramics experience hardening (aged state) - softening (deaged state) transition, delta3 changes by about 90 degrees at subswitching fields and by about 180 degrees at switching conditions. Evolution of delta3 with time, temperature and electric field amplitude during deageing suggests th…
The observation of strong magnetoelectric effects is reported in thick film bilayers and multilayers of ferrite-lead titanate zirconate (PZT) and lanthanum nanganite-PZT. The ferrites used in our studies included pure and zinc substituted cobalt-, nickel- and lithium ferrites. Samples were prepared by sintering 10-40 mm thick films obtained by tape-casting. Measurements of ME voltage coefficients at 10-1000 Hz indicated a giant ME effect in nickel ferrite-PZT, but a relatively weak coupling in other ferrite-PZT and manganite-PZT systems. Multilayers prepared by hot pressing was found to show a…
We report on the frequency and stress dependence of the direct piezoelectric d33 coefficient in BiFeO3 ceramics. The measurements reveal considerable piezoelectric nonlinearity, i.e., dependence of d33 on the amplitude of the dynamic stress. The nonlinear response suggests a large irreversible contribution of non-180° domain walls to the piezoelectric response of the ferrite, which, at present measurement conditions, reached a maximum of 38% of the total measured d33. In agreement with this interpretation, both types of non-180° domain walls, characteristic for the rhombohedral BiFeO3, i.e., 7…
High resolution x-ray powder diffraction measurements on poled PbZr(1-x)TixO3 (PZT) ceramic samples close to the rhombohedral-tetragonal phase boundary (the so-called morphotropic phase boundary, MPB) have shown that for both rhombohedral and tetragonal compositions, the piezoelectric elongation of the unit cell does not occur along the polar directions but along those directions associated with the monoclinic distortion. This work provides the first direct evidence for the origin of the very high piezoelectricity in PZT.
A method for evaluating the piezoelectric response of unpoled ferroelectric ceramics from elastic and dielectric measurements is proposed and tested on BaTiO$_3$. The method is based on the observation that the softening in a ferroelectric phase with respect to the paraelectric phase is of piezoelectric origin. The angular averages of the piezoelectric softening in unpoled ceramics are calculated for ferroelectric phases of different symmetries. The expression of the orientational average with the piezoelectric and dielectric constants of single crystal tetragonal BaTiO$_3$ from the literature…
In piezoelectric ceramics the changes in the phase stabilities versus stress and temperature in the vicinity of the phase boundary play a central role. The present study was dedicated to the classical piezoelectric, lead-zirconate-titanate (PZT) ceramic with composition Pb(Zr$_{0.54}$Ti$_{0.46}$)O$_3$ at the Zr-rich side of the morphotropic phase boundary at which both intrinsic and extrinsic contributions to piezoelectricity are significant. The pressure-induced changes in this two-phase (rhombohedral $R3c$+monoclinic $Cm$ at room temperature and $R3c+P4mm$ above 1 GPa pressures) system were …
PbZr_{1-x}Ti_xO_3 (PZT) and Pb(Mg_{1/3}Nb_{2/3})_{1-x}Ti_xO_3 (PMN-$x$PT) are complex lead-oxide perovskites that display exceptional piezoelectric properties for pseudorhombohedral compositions near a tetragonal phase boundary. In PZT these compositions are ferroelectrics, but in PMN-xPT they are relaxors because the dielectric permittivity is frequency dependent and exhibits non-Arrhenius behavior. We show that the nanoscale structure unique to PMN-xPT and other lead-oxide perovskite relaxors is absent in PZT and correlates with a greater than 100% enhancement of the longitudinal piezoelectr…
We report on the discovery of a lead-free morphotropic phase boundary in Sm doped BiFeO3 with a simple perovskite structure using the combinatorial thin film strategy. The boundary is a rhombohedral to pseudo-orthorhombic structural transition which exhibits a ferroelectric (FE) to antiferroelectric (AFE) transition at approximately Bi0.86Sm0.14FeO3 with dielectric constant and out-of-plane piezoelectric coefficient comparable to those of epitaxial (001) oriented Pb(Zr,Ti)O3 (PZT) thin films at the MPB. The discovered composition may be a strong candidate of a Pb-free piezoelectric replacement…
The traditional derivation of the elastic anomalies associated with ferroelectric (FE) phase transitions in the framework of the Landau theory is combined with the piezoelectric constitutive relations instead of being explicitly carried out with a definite expression of the FE part of the free energy. In this manner it is shown that the softening within the FE phase is of electrostrictive and hence piezoelectric origin. Such a piezoelectric softening may be canceled by the better known piezoelectric stiffening, when the piezoelectric charges formed during the vibration are accompanied by the d…
The thermal conductivity of polycrystalline bulk PZT (lead-zirconate-titanate) has been investigated according to electrical boundary conditions and poling. The thermal conductivity of poled PZT was measured in the poling direction for open circuit and short circuit conditions. The short circuit thermal conductivity had the largest thermal conductivity. The relationship between these two thermal properties, the electrothermal coupling factor $k_{33}^κ$, was found to be similar to the electromechanical coupling factor $k_{33}$ relating elastic compliance under short circuit and open circuit con…
We have investigated the behavior of the PbZr(0.94}Ti(0.06)O3 Raman spectra as a function of Hydrostatic pressures. The new structural phases were identified based on previous works performed in PZT system with different Ti concentrations at room- and high pressures. We showed that PbZr(0.94}Ti(0.06}O3 exhibits a rich phase sequence up to 3.7 GPa: rhombohedral(LT) {0.3 GPa} orthorhombic(I) {2.9 GPa} orthorhombic(I'). This sequence is different from that exhibited by PbZr(0.90)Ti(0.10)O3 suggesting a very interesting concentration-pressure phase diagram for rich Zr PZT system.
The lattice strain and domain switching behaviour was investigated as a function of cyclic field and grain orientation for a pseudorhombohedral composition of the high Curie point piezoelectric system xBiScO3 - (1-x)PbTiO3 (x = 0.40) by in-situ electric field diffraction technique with high energy synchrotron x-rays. Along the field direction, the system exhibts five time large strain along 100 as compared to the 111 direction. A one-to-one correspondence between the 200 lattice strain and the 111 domain switching suggests a strong correlation between the two phenomena.
We report a more than 10-fold enhancement of the piezoelectric coefficient $d_{33}$ of polycrystalline CH$_3$NH$_3$PbI$_3$ (MAPbI$_3$) films when interfacing them with ferroelectric PbZr$_{0.2}$Ti$_{0.8}$O$_3$ (PZT). Piezo-response force microscopy (PFM) studies reveal $d_{33}^{MAPbI_3}$ values of ~0.3 pm/V for MAPbI$_3$ deposited on Au and ITO surfaces, with small phase angles fluctuating at length scales smaller than the grain size. In sharp contrast, on samples prepared on epitaxial PZT films, we observe large scale polar domains exhibiting clear, close to 90° PFM phase angles, pointing to …
Strong piezoelectricity in the perovskite-type PbZr(1-x)TixO3 (PZT) and Pb(Zn1/3Nb2/3)O3-PbTiO3 (PZN-PT) systems is generally associated with the existence of a morphotropic phase boundary (MPB) separating regions with rhombohedral and tetragonal symmetry. An x-ray study of PZN-9%PT has revealed the presence of a new orthorhombic phase at the MPB, and a near-vertical boundary between the rhombohedral and orthorhombic phases, similar to that found for PZT between the rhombohedral and monoclinic phases. We discuss the results in the light of a recent theoretical paper by Vanderbilt and Cohen, wh…
Recent years have witnessed considerable work on the development of lead-free piezoelectric ceramic materials and their structure-property correlations. The development of piezo response is a strong function of phase evolution in these materials. In this work, we report the effect of Ru doping and consequent phase evolution on maximization of piezoelectric response of polycrystalline lead-free barium titanate, depicted as Ba(RuxTi1-x)O3 (BRT). The samples were prepared in a narrow compositional range of using conventional solid-state reaction method. Ru doping increases the leakage current of …
A new lead-free (1-x)Li0.12Na0.88NbO3-xBaTiO3 (0 to x to 40) piezoelectric ceramics have been prepared using conventional ceramics processing route. Structural analysis revealed an existence of morphotropic phase boundary (MPB), separating orthorhombic and tetragonal phases, between the BaTiO3 content, x = 10-12.5. A partial phase diagram has been established based on temperature-dependent permittivity data for this new system and a nearly vertical temperature-independent MPB is observed. An improvement in electrical properties near MPB (e.g., for x = 12.5; εr = 10489 at Tm, d33 = 30 pC/N, kp …
Piezoelectric and ferroelectric ceramics with a high Curie temperature (Tc) have attracted a growing attention owning to their applications under severe environments. In this work, phase structure, dielectric, ferroelectric and piezoelectric properties of (0.975-x)BiScO3-xPbTiO3-0.025Pb(Cd1/3Nb2/3)O3 ceramics (x = 0.58-0.64) were studied. A composition-induced structural transformation occurs from rhombohedral phase to tetragonal phase through an intermediate monoclinic phase with the increasing PT concentration. The relationship between structure and electrical properties of the system were d…
An optimization procedure determining the ideal configuration at the microstructural level of ferroelectric (FE) materials is applied to maximize piezoelectricity. Piezoelectricity in ceramic FEs differ significantly from that of single crystals because of the presence of crystallites (grains) possessing crystallographic axes aligned imperfectly. The piezoelectric properties of a polycrystalline (ceramic) FE is inextricably related to the grain orientation distribution (texture). The set of combination of variables, known as solution space, which dictates the texture of a ceramic is unlimited …
A first-principles-derived approach is used to study structural, piezoelectric and dielectric properties of Pb(Zr_{1-x}Ti_{x})O_{3} (PZT) solid solutions near the morphotropic phase boundary at low temperature. Three ferroelectric phases are found to exist: a tetragonal phase for larger x compositions, a rhombohedral phase for smaller x compositions, and the recently discovered monoclinic phase in between. In this monoclinic phase, the polarization associated with the Zr atoms behaves differently from the polarization associated with the Ti atoms. As the composition x decreases, the former rot…
Recently discovered fine structure of the morphotropic phase boundaries in highly piezoelectric mixture compounds PZT, PMN-PT, and PZN-PT demonstrates the importance of highly non-linear interactions in these systems. We show that an adequate Landau-type description of the ferroelectric phase transitions in these compounds is achieved by the use of a twelfth-order expansion of the Landau potential in terms of the phenomenological order parameter. Group-theoretical and catastrophe-theory methods are used in constructing the appropriate Landau potential. A complete phase diagram is calculated in…
The importance of a high shear coefficient d15 (or d24) to the piezoelectric properties of domain-engineered and polycrystalline ferroelectrics is discussed. The extent of polarization rotation, as a mechanism of piezoelectric response, is directly correlated to the shear coefficient. The terms "rotator" and "extender" are introduced to distinguish the contrasting behaviors of crystals such as 4mm BaTiO3 and PbTiO3. In "rotator" ferroelectrics, where d15 is high relative to the longitudinal coefficient d33, polarization rotation is the dominant mechanism of piezoelectric response; the maximum …
We have studied the processing of piezoelectric thick films using electrophoretic deposition (EPD) for high-frequency ultrasound applications. Lead-zirconium-titanate (PZT) particles synthetized by solid states synthesis were dispersed in ethanol using ammonium polyacrylate (PAA). The electrophoretic deposition of PZT particles was performed at a constant-current mode. PZT thick-films deposited at 1 mA for 60 seconds were sintered at 900oC for 2 hours in a PbO-controlled atmosphere. The scanning-electron microscopy (SEM) analysis shows that the thickness of PZT layer is uniform and that the po…
High performance lead zirconate titanate (PZT) ceramics with aligned porosity for sensing applications were fabricated by an ice-templating method. To demonstrate the enhanced properties of these materials and their potential for sensor and hydrophone applications, the piezoelectric voltage constants hydrostatic parameters and AC conductivity as a function of the porosity in directions both parallel and perpendicular to the freezing temperature gradient were studied. As the porosity level was increased, PZT poled parallel to the freezing direction exhibited the highest coefficients, and hydros…
The powder of barium titanate (BaTiO3) synthesized by solid state was characterised by spherical grains of the average size about 500 nm. The double mechanical activation and calcination of raw materials was necessary to receive the monophase material. In order to improve the mouldability, the obtained barium titanate powder was granulated in spray drier. Pellets and beams from BaTiO3 granulate were manufactured by both uniaxial and isostatic pressing. The properties of barium titanate material at each stage of its fabrication (powder, granulate, sintered material) influencing on its applicati…
Polymer-piezoceramic 0-3 composites combine the flexibility of the polymers and the excellent piezoelectric properties of the ferroelectric based ceramic. While grain size of the ceramic powder is one of the important considerations in the fabrication of such composites, a correlation relating poling field induced structural changes and its possible influence on the overall piezoelectric response of the composite is still lacking. In this paper, we examine this issue on a 0-3 piezo-composite comprising of a ceramic powders of a low-lead piezoelectric alloy (x)Bi(Ni1/2Zr1/2O3-(1-x)PbTiO3 in pro…
Oxygen octahedra tilting is a common structural phenomenon in perovskites and has been subject of intensive studies, particularly in rhombohedral Pb(Zr,Ti)O3 (PZT). Early reports suggest that the tilted octahedra may strongly affect the domain switching behavior, dielectric and piezoelectric properties of PZT ceramics. In a way similar to that proposed for tilts, however, charged defects, associated with oxygen vacancies, may also inhibit the motion of the domain walls, resulting macroscopically in pinched hysteresis loops and reduced piezoelectric response. Here, we revisit the early studies …
Magnetoelectric (ME) effect has been studied in a structure of a magnetostrictive TbFe2 alloy, two piezoelectric Pb(Zr,Ti)O3 (PZT) ceramics, and two nonmagnetic flakes. The ME coupling originates from the magnetic-mechanical-electric transform of the magnetostrictive effect in TbFe2 and the piezoelectric effect in PZT by end bonding, instead of interface bonding. Large ME coefficients of 10.5 and 9.9 Vcm-1Oe-1 were obtained at the first planar acoustic and third bending resonance frequencies, which are larger than that of conventional layered TbFe2/PZT composites. The results show that the lar…
This paper investigates the deflection of micro- electro-mechanical system (MEMS) based sandwiched cantilever beam for piezoelectric actuation using eight of the popular lead zirconatetitanate (PZT)piezoceramic material. The simulation for the investigation was carried away in COMSOL Multiphysics software environment. For the investigation of a certain model, the lowest tip deflection is found to be 38.074 nm for PZT-8 and the highest tip deflection is found to be 82.965 nm for PZT-5H. A 2 mm thick flexible foam core is sandwiched between two 8 mm thick aluminum layers in this model of sandwic…
An impedance spectroscopy (IS) is a versatile tool to study the effect of grains (bulk), grain boundaries and electrode-electrolyte interface on dielectric and electrical properties of electro-ceramics. This study only focuses the high frequency (1 kHz to 10 MHz) probe of bulk ferroelectric capacitance near ferroelectric phase transition temperature (FPTT). The PZTFW single phase and PZTFW-CFO composites, respectively, have been investigated to understand the microstructure-property relation. Keeping in mind the complex microstructure of both systems, low frequency ( less than 1 kHZ ) impedanc…
Structural and Optical properties of the (Na0.5 K0.5)y Li 1-y NbO3 (y = 0.934 & 0.936) ceramics have been explored in terms of the X-Ray diffraction patters, Rietveld analysis, UV-Vis spectroscopy, and Kubelka-Munk functions. Rietveld analysis of both these structures reveals them to be tetragonal with space group P4mm. It is found that increase in Li doping increases the optical band gap. Presence of additional hardening dopant MnO2 is found to have a uniform behavior for both these composition. With increasing MnO2 concentration, the band gap decreases indicative of increase in B-site cation…
Temperature-dependent dielectric permittivity of lead-free (LixNa1-x)NbO3 for nominal x = 0.04-0.20, prepared by solid state reaction followed by sintering, was studied to resolve often debated issue pertaining to exactness of morphotropic phase boundary (MPB) location along with structural aspects and phase stability in the system near MPB. Interestingly, a diffuse phase transition has been observed in the dielectric permittivity peak arising from the disorder induced in A-site and structural frustration in the perovskite cell due to Li substitution. A partial phase diagram has been proposed …
Dielectric behavior and conductivity mechanism in lead-free (100-x)(Li0.12Na0.88)NbO3-xBaTiO3 (0 to x to 40) piezoelectric ceramics were investigated using impedance spectroscopy over a wide temperature (-100 oC to500 oC) and frequency range (0.1 Hz to1 MHz). The grain and grain boundary response as well as the relaxation processes at different frequencies and temperatures were also discussed. A low frequency dispersion in dielectric permittivity (LFDD), a typical characteristic of high-temperature behavior was observed both below and above the ferro-paraelectric phase transition temperature, …
In this paper, a comprehensive methodology for characterizing the high power resonance behavior of bulk piezoelectric ceramics using the burst method is described. In the burst method, the sample is electrically driven at its resonance frequency, and then either a short circuit or an open circuit condition is imposed, after which the vibration decays at the resonance or antiresonance frequency, respectively. This decay can be used to measure the quality factor in either of these conditions. The resulting current in the short circuit vibration condition is related to the vibration velocity thro…
SrTiO3 ceramics are investigated by piezoresponse force microscopy. Piezoelectric contrast is observed on polished surfaces in both vertical and lateral regimes and depends on the grain orientation varying in both sign (polarization direction) and amplitude. The observed contrast is attested to the surface piezoelectricity due to flexoelectric effect (strain gradient-induced polarization) caused by the surface relaxation. The estimated flexoelectric coefficient is approximately one order of magnitude smaller as compared to those recently measured in SrTiO3 single crystals. The observed enhance…
For the past two decades piezo MEMS technology are emerging for its low power consumption of ultrasonic sensing and actuation devices for biomedical applications. Still researchers are facing challenges in miniaturization of piezo-MEMS devices. But up-to-date there is no reports on achieving better sensitivity and actuation strength properties in the same piezoelectric material. As piezoelectric materials are anisotropic in nature, for that it is essential to grow different textured PZT thin film on a single silicon substrate. In the present investigation we have demonstrated the simple method…
We report a first-principles study of a class of (BiScO3)_{1-x}-(PbTiO3)_x (BS-PT) alloys recently proposed by Eitel et al. as promising materials for piezoelectric actuator applications. We show that (i) BS-PT displays very large structural distortions and polarizations at the morphotropic phase boundary (MPB) (we obtain a c/a of ~1.05-1.08 and P_tet of ~1.1 C/m^2); (ii) the ferroelectric and piezoelectric properties of BS-PT are dominated by the onset of hybridization between Bi/Pb-6p and O-2p orbitals, a mechanism that is enhanced upon substitution of Pb by Bi; and (iii) the piezoelectric r…
Lead-free ceramics (K0.44+xNa0.52Li0.04)(Nb0.86Ta0.10Sb0.04)O3+x/2 (x=-0,06) were prepared by conventional solid state sintering. The results indicate a correlation between crystalline symmetry and electrical properties. Higher tetragonality was observed in samples with higher piezoelectric response. As the tetragonality increase the presence of polymorphic phase decrease associated with a reduction of the relaxor behaviour response. The ceramics with c/a = 1.011 ratio exhibit enhanced electrical properties. The Raman spectroscopy showed a certain asymmetry in the paraelectric phase above the …
In this work, a new methodology for comparing high power performance of different piezoelectric materials is presented. When comparing high power performance of piezoelectric materials of varying compositions and vibration modes, there exists an inherent problem in comparing the mechanical quality factor directly. Typically the behavior of the mechanical quality factor is reported as a function of tip vibration velocity of the sample. This paper shows why this approach can be inherently problematic and proposes an energy approach to characterize the mechanical quality factor as the solution. B…
The oxygen octahedral tilted domains in 0.90(Bi1/2Na1/2)TiO3-0.5(Bi1/2K1/2)TiO3-0.5BaTiO3 lead-free perovskite piezoelectric ceramic have been studied by transmission electron microscopy (TEM). Selected-area electron diffraction patterns shows the 1/2ooo and 1/2ooe reflections, indicating the presence of antiphase (a-a-a-) and in-phase (aoaoc+) octahedral tilting, respectively. The morphology and distributions of these tilted domains are shown in the centered dark-field images. Further, the Bragg-filtered high-resolution TEM image reveals that the size of the in-phase tilted domains varies fro…
Pb(Mg1/3Nb2/3)O3-PbTiO3 solid solution (PMN(1-x)-PTx) ceramics with 0 <x<1 have been prepared by homo-epitaxial templated grain growth (HTGG) using cubic PMN-PT single crystal seeds as templates and nanoparticles for thes ceramic matrix. Samples were prepared using the doctor Blade method and sintered in a controlled atmosphere. They were then analysed by DTA, TGA, optical/scanning electron microscopy, Raman spectroscopy and imaging. Relationships between Raman parameters such as band component or area versus composition (x) are proposed. Wavenumber and peak area shifts from the single crystal…
We report the high strength of magnetoelectric (ME) coupling of trilayered composites prepared by electro-deposition. The ME coupling of Ni-lead zirconate titanate (PZT)-Ni trilayered structure was measured ranged from1 kHz to 120 kHz. The trilayered composites exhibit high magnetoelectric voltage coefficient because of good bonding between piezoelectric and magnetostrictive layers. The maximum magnetoelectric voltage coefficient can be up to 33 V/cm Oe at the electromechanical resonance frequency. This magnetoelectric effect shows promising application in transducers for magnetoelectric energ…
In this work, we address the issue of peaking of piezoelectric response at a particular composition in the morphotropic phase boundary (MPB) region of (Pb0.940Sr0.06)(ZrxTi1-x)O3 (PSZT) piezoelectric ceramics. We present results of synchrotron x-ray powder diffraction, dielectric, piezoelectric and sound velocity studies to critically examine the applicability of various models for the peaking of physical properties. It is shown that the models based on the concepts of phase coexistence, polarization rotation due to monoclinic structure, tricritical point and temperature dependent softening of…
The high frequency performance of strong piezoelectric materials like PZT remains relatively less explored due to the assumption of large dielectric/ferroelectric losses at GHz frequencies. Recently, the advent of magnetoelectric technology as an on-chip route to excite magnetization dynamics has provided the impetus to evaluate the electromechanical performance of PZT at microwave frequencies. In this work, we demonstrate that HBARs fabricated using Barium-doped PZT (BPZT) films can efficiently generate acoustic waves up to 15 GHz. The ferroelectricity of BPZT endows added functionality to th…
The PZT material near the morphotropic phase boundary where a monoclinic phase was observed is studied. A theory of the tetragonal to monoclinic phase transition was developed within the Landau free energy approach. The phase transition from the tetragonal to the monoclinic phase is of the first order near the second order. Dielectric response near the phase transition from the tetragonal to the monoclinic phase was studied for the crystal and for the ceramic and polycrystalline material taking into account the diagonal 33 and the off diagonal 31 components of susceptibility. The later diverge…
