We report on a novel optofluidic system consisting of a silica-based 1D photonic crystal, integrated planar waveguides and electrically insulated fluidic channels. An array of pillars in a microfluidic channel designed for electrochromatography is used as a resonator for on-column label-free refractive index detection. The resonator was fabricated in a silicon oxynitride platform, to support electroosmotic flow, and operated at 1.55 microns. Different aqueous solutions of ethanol with refractive indices ranging from n = 1.3330 to 1.3616 were pumped into the column/resonator and the transmission spectra were recorded. Linear shifts of the resonant wavelengths yielded a maximum sensitivity of 480 nm/RIU and a minimum difference of 0.007 RIU was measured.
Currently, optical- or mechanical-resonances are commonly used in microfluidic research. However, optomechanical oscillations by light pressure were not shown with liquids. This is because replacing the surrounding air with water inherently increases the acoustical impedance and hence the associated acoustical radiation-losses. Here, we bridge between microfluidics and optomechanics by fabricating hollow bubble resonators with liquid inside and optically exciting 100-MHz vibrations with only mW optical-input power. This constitutes the first time that any microfluidic system is optomechanicall…
Photonic hook (PH) is a new type of artificial self-bending beam focused by a dielectric particle-lens with a curved waist smaller than the wavelength, which has the potential to revolutionize mesoscale photonics in many applications, e.g., optical trapping, signal switching, imaging, etc. In this paper, we discover a new mechanism that the highly curved PHs can be realised by the light interaction with the fully or partially metal-coated microchannels. The generated W-shaped and J-shaped PHs have bending angles exceeding 80-degree. Compared to other PH setups, the proposed design has a larger…
The microfluidic optomechanical resonator (uFOMR) based on a thin-walled glass capillary supports high Q-factor (>1000) mechanical modes in the presence of liquids. In this Letter, the sensitivity of the uFOMR to the surface change is studied by layer-by-layer removal of SiO2 molecules from the uFOMR inner surface using various concentrations of hydrofluoric acid solutions. A frequency downshift is observed with a sensitivity of 1.2 Hz/(pg/mm2), which translates to a surface density detection limit of 83 pg/mm2. This work opens a door to using the optomechanical mode for detection and characte…
Operation of nanomechanical devices in water environment has been challenging due to the strong viscous damping that greatly impedes the mechanical motion. Here we demonstrate an optomechanical micro-wheel resonator integrated in microfluidic system that supports low-loss optical resonances at near-visible wavelength with quality factor up to 1.5 million. The device can be operated in self-oscillation mode in air with low threshold power of 45 uW. The very high optical Q allows the observation of the thermal Brownian motion of the mechanical mode in both air and water environment with high sig…
We report a novel technique for launching broadband laser light into liquid-filled hollow-core photonic crystal fiber (HC-PCF). It uniquely offers self-alignment and self-stabilization via optomechanical trapping of a fused silica nanospike, fabricated by thermally tapering and chemically etching a single mode fiber into a tip diameter of 350 nm. We show that a trapping laser, delivering ~300 mW at 1064 nm, can be used to optically align and stably maintain the nanospike at the core center. Once this is done, a broadband supercontinuum beam (~575 to 1064 nm) can be efficiently and close to ach…
We report on the proposal and experimental realization of a spoof surface plasmon Fabry-Perot (FP) open resonator in a surface-wave photonic crystal. This surface-wave FP open resonator is formed by introducing a finite line defect in a surface-wave photonic crystal. The resonance frequencies of the surface-wave FP open resonator lie exactly within the forbidden band gap of the surface-wave photonic crystal and the FP open resonator uses this complete forbidden band gap to concentrate surface waves within a subwavelength cavity. Due to the complete forbidden band gap of the surface-wave photon…
A topologically protected ring-resonator formed in valley photonic crystals is proposed and fabricated on a silicon slab. The unidirectional transmission and robustness against structure defects of its resonant modes are illustrated. Coupled with topological waveguides, the topological ring is functioned as notch and channel-drop filters. The work opens up a new avenue for developing advanced chip-integrated photonic circuits with attributes of topological photonics.
We designed an on-chip transformative optic system of a metalens-photonic crystal resonator metasystem on a foundry compatible silicon photonic platform. By adjusting the on-chip metalens' focusing length and mode dimension, the insertion loss between the metalens and the photonic crystal resonator and waveguide structures are minimized through mode-matching. The micro-system does not involve any single mode silicon nanowire waveguide, and thus mechanically robust without any oxide claddings. The proposed microsystem is ideal for miniaturized chemical and biosensors operating in air or solutio…
The integration of photonic sensors into microfluidic devices provides opportunities for dynamic measurement of chemical and physical properties of fluids in very small volumes. We previously reported on the use of commercially available Fiber Bragg Gratings (FBGs) and on-chip silicon waveguides for temperature sensing. In this report, we demonstrate the integration of FBGs into easy-to-fabricate microfluidic devices and report on their sensitivity for temperature and pressure measurement in microliter volumes. These sensors present new routes to measurement in microfluidic applications such a…
Photonic molecules can be used to realize complex optical energy states and modes, analogous to those found in molecules, with properties useful for applications like spectral engineering and quantum optics. It is desirable to implement photonic molecules using high quality factor photonic integrated ring resonators due to their narrow atom-like spectral resonance, tunability, and the ability to scale the number of resonators on a photonic circuit. However, to take full advantage of molecule spectral complexity and tuning degree of freedom, resonator structures should have full symmetry in ter…
We describe a method that enables free-standing whispering-gallery-mode microresonators, and report spectral tuning of photonic molecules formed by coupled free and on-chip resonators with different geometries and materials. We study direct coupling via evanescent fields of free silica microtoroids and microspheres with on-chip polymer coated silica microtoroids. We demonstrate thermal tuning of resonance modes to achieve maximal spectral overlap, mode splitting induced by direct coupling, and the effects of distance between the resonators on the splitting spectra.
Fast and highly accurate method based on the Muller contour integral equations and a trigonometric-trigonometric Galerkin discretization technique is presented for spectral design and fine-tuning of clusters of whispering-gallery (WG) mode microdisk resonators and photonic crystal (PC) defect cavities. It is shown that degeneracy and near-degeneracy of natural modes as well as modes optical confinement in coupled resonator clusters are significantly influenced by the symmetry of the structure. Photonic molecules with greatly enhanced quality factors are designed by exploiting the symmetry of t…
Canonical Four-Wave-Mixing occurs in a resonator with only the required number of modes, thereby inhibiting competing parametric processes. The properties of the recently introduced photonic crystal parametric oscillator, Marty et al. Nat. Photonics, 15, 53 (2021), are discussed extensively. We compare the bichromatic design with other geometries of photonic crystal resonators. Based on a statistical study over more than 100 resonators and 10 parametric oscillators, robustness against fabrication tolerances is assessed, performances are evaluated in terms of average values and their dispersion…
We study photonic crystal fibers and ring resonators with topological features induced by Aubry- Andre-Harper modulations of the cladding. We find non trivial gaps and edge states at the interface between regions with different Chern numbers. We calculate the field profile and eigenvalue dispersion by an exact recursive approach. Compared with conventional circular resonators and fibers, the proposed structure features topological protection and hence robustness against symmetry-preserving local perturbations that do not close the gap. These topological photonic crystal fibers sustain strong f…
Optical bistability provides a simple way to control light with light. We demonstrate low-power thermo-optical bistability caused by the Joule heating mechanism in a one-dimensional photonic crystal (PC) nanobeam resonator with a moderate quality factor (Q ~ 8900) with an embedded reverse-biased pn-junction. We show that the photocurrent induced by the linear absorption in this compact resonator considerably reduces the threshold optical power. The proposed approach substantially relaxes the requirements on the input optical power for achieving optical bistability and provides a reliable way t…
Tight confinement of light in photonic cavities provides an efficient template for the realization of high optical intensity with strong field gradients. Here we present such a nanoscale resonator device based on a one-dimensional photonic crystal slot cavity. Our design allows for realizing highly localized optical modes with theoretically predicted Q factors in excess of 106. The design is demonstrated experimentally both in a high-contrast refractive index system (silicon), as well as in medium refractive index contrast devices made from aluminum nitride. We achieve extinction ratio of 21dB…
We outline the design for a photonic crystal resonator made in a hybrid Silicon/Lithium Niobate material system. Using the index contrast between silicon and lithium niobate, it is possible to guide and confine photonic resonances in a thin film of silicon bonded on top of lithium niobate. Quality factors greater than $10^6$ at optical wavelength scale mode volumes are achievable. We show that patterning electrodes on such a system can yield an electro-optic coupling rate of 0.6 GHz/V (4 pm/V).
We present the design and fabrication of photonic crystal structures exhibiting electromagnetic bands that are flattened in all crystal directions, i.e., whose frequency variation with wavevector is minimized. Such bands can be used to reduce group velocity of light propagating in arbitrary crystal direction, which is of importance for construction of miniaturized tunable optical delay components, low-threshold photonic crystal lasers, and study of nonlinear optics phenomena.
Resistance thermometry provides a time-tested method for taking temperature measurements. However, fundamental limits to resistance-based approaches has produced considerable interest in developing photonic temperature sensors to leverage advances in frequency metrology and to achieve greater mechanical and environmental stability. Here we show that silicon-based optical ring resonator devices can resolve temperature differences of 1 mK using the traditional wavelength scanning methodology. An even lower noise floor of 80 microkelvin for measuring temperature difference is achieved in the side…
Lab-on-a-Chip (LoC) devices combining microfluidic analyte provision with integrated optical analysis are highly desirable for several applications in biological oder medical sciences. While the microfluidic approach is already broadly adressed, yet some work needs to be done regarding the integrated optics, especially provision of highly integrable laser sources. Polymer optical fiber (POF) lasers represent an alignment-free, rugged and flexible technology platform. Additionally, POFs are intrinsically compatible to polymer microfluidic devices. Home-made Rhodamine B (RB) doped POFs were char…
We demonstrate waveguide-coupled titanium dioxide (TiO2) racetrack resonators with loaded quality factors of 2x10^4 for the visible wavelengths. The structures were fabricated in sputtered TiO2 thin films on oxidized silicon substrates using standard top-down nanofabrication techniques, and passively probed in transmission measurements using a tunable red laser. Devices based on this material could serve as integrated optical elements as well as passive platforms for coupling to visible quantum emitters.
Coupled split-ring-resonator metamaterials have previously been shown to exhibit large coupling effects, which are a prerequisite for obtaining large effective optical activity. By a suitable lateral arrangement of these building blocks, we completely eliminate linear birefringence and obtain pure optical activity and connected circular optical dichroism. Experiments at around 100-THz frequency and corresponding modeling are in good agreement. Rotation angles of about 30 degrees for 205nm sample thickness are derived.
Current quantum cascade lasers based upon conduction band electron transitions are predominantly TM (electrical field normal to the epitaxial direction) polarized. Here we present a study of localized defect modes, with the requisite TM polarization, in connected square and hexagonal lattice two-dimensional (2D) photonic crystals for application as quantum cascade laser resonators. A simple group-theory based analysis is used to produce an approximate description of the resonant modes supported by defects situated at different high symmetry points within the host photonic lattice. The results …
Photonic systems based on microring resonators have a fundamental constrain given by the strict relationship among free spectral range (FSR), total quality factor (QT) and resonator size, intrinsically making filter spacing, photonic lifetime and footprint interdependent. Here we break this paradigm employing CMOS compatible Silicon-on-Insulator (SOI) photonic molecules based on coupled multiple ring resonators. The resonance wavelengths and their respective linewidths are controlled by the hybridization of the quasi-orthogonal photonic states. We demonstrate photonic molecules with doublet an…
We study the resonant transmission of light in a coupled-resonator optical waveguide interacting with two nearly identical side cavities. We reveal and describe a novel effect of the coupled-resonator-induced reflection (CRIR) characterized by a very high and easily tunable quality factor of the reflection line, for the case of the inter-site coupling between the cavities and the waveguide. This effect differs sharply from the coupled-resonator-induced transparency (CRIT) -- an all-optical analogue of the electromagnetically-induced transparency -- which has recently been studied theoretically…
We analyze the resonant linear and nonlinear transmission through a photonic crystal waveguide side-coupled to a Kerr-nonlinear photonic crystal resonator. Firstly, we extend the standard coupled-mode theory analysis to photonic crystal structures and obtain explicit analytical expressions for the bistability thresholds and transmission coefficients which provide the basis for a detailed understanding of the possibilities associated with these structures. Next, we discuss limitations of standard coupled-mode theory and present an alternative analytical approach based on the effective discrete …
We demonstrate a photonic RF Hilbert transformer for broadband microwave in-phase and quadrature-phase generation based on an integrated frequency optical comb, generated using a nonlinear microring resonator based on a CMOS compatible, high-index contrast, doped-silica glass platform. The high quality and large frequency spacing of the comb enables filters with up to 20 taps, allowing us to demonstrate a quadrature filter with more than a 5-octave (3 dB) bandwidth and an almost uniform phase response.
We demonstrate wideband integrated photonic circuits in sputter-deposited aluminum nitride (AlN) thin films. At both near-infrared and visible wavelengths, we achieve low propagation loss in integrated waveguides and realize high-quality optical resonators. In the telecoms C-band (1520-1580 nm), we obtain the highest optical Q factor of 440,000. Critical coupled devices show extinction ratio above 30 dB. For visible wavelengths (around 770 nm), intrinsic quality factors in excess of 30,000 is demonstrated. Our work illustrates the potential of AlN as a low loss material for wideband optical ap…
We report enhanced optomechanical coupling by embedding a nano-mechanical beam resonator within an optical race-track resonator. Precise control of the mechanical resonator is achieved by clamping the beam between two low-loss photonic crystal waveguide couplers. The low insertion loss and the rigid mechanical support provided by the couplers yield both high mechanical and optical Q-factors for improved signal quality.
We report a simple technique in microwave photonic (MWP) signal processing that allows the use of an optical filter with a shallow notch to exhibit a microwave notch filter with anomalously high rejection level. We implement this technique using a low-loss, tunable Si3N4 optical ring resonator as the optical filter, and achieved an MWP notch filter with an ultra-high peak rejection > 60 dB, a tunable high resolution bandwidth of 247-840 MHz, and notch frequency tuning of 2-8 GHz. To our knowledge, this is a record combined peak rejection and resolution for an integrated MWP filter.
We build ring resonators to assess the potentialities of Kagome Hollow-Core Photonic Crystal Fibers for future applications to resonant rotation sensing. The large mode diameter of Kagome fibers permits to reduce the free space fiber-to-fiber coupling losses, leading to cavities with finesses of about 30 for a diameter equal to 15 cm. Resonance linewidths of 3.2~MHz with contrasts as large as 89\% are obtained. Comparison with 7-cell photonic band gap (PBG) fiber leads to better finesse and contrast with Kagome fiber. Resonators based on such fibers are compatible with the angular random walk …
The evanescent coupling from a photonic crystal resonator to a micron-thick optical fiber is investigated in detail by using a 3D-FDTD method. Properly designed photonic crystal cavity and taper structures are proposed, and optimal operating conditions are found to enhance the coupling strength while suppressing other cavity losses including the coupling to the slab propagating mode and to the higher-order fiber mode. In simulation, the coupling into the fundamental fiber mode is discriminated from other cavity losses by spatial and parity filtering of the FDTD results. The coupling efficiency…
An array of ring resonators specifically designed can perform as a topological insulator. We conduct simulations using both Tight-Binding Model (TBM) and Transfer Matrix Method (TMM) to analyze the transport properties of such optical structure, verifying the presence of robust topological edge states which is immune to disorder and defect. We have also made a comparison between these two methods, of which results suggesting that TBM is only applicable under weakly-coupling condition while TMM is more rigorous. Finally we compared the structure with common microring array and coupled resonator…
We introduce a numerical procedure which permits to drastically accelerate the design of multimode photonic crystal resonators. Specifically, we demonstrate that the optical response of an important class of such nanoscale structures is reproduced accurately by a simple, one-dimensional model, within the entire spectral range of interest. This model can describe a variety of tapered photonic crystal structures. Orders of magnitude faster to solve, our approach can be used to optimize certain properties of the nanoscale cavity. Here we consider the case of a nanobeam cavity, where the confineme…
We develop a model for the coupling of quasi-normal modes in open photonic systems consisting of two resonators. By expressing the modes of the coupled system as a linear combination of the modes of the individual particles, we obtain a generalized eigenvalue problem involving small size dense matrices. We apply this technique to dielectric rod dimmer of rectangular cross section for Transverse Electric (TE) polarization in a two-dimensional (2D) setup. The results of our model show excellent agreement with full-wave finite element simulations. We provide a convergence analysis, and a simplifi…
We demonstrate the first compact photonic flywheel with sub-fs time jitter (averaging times up to 10 μs) at the quantum-noise limit of a monolithic fiber resonator. Such quantum-limited performance is accessed through novel two-step pumping scheme for dissipative Kerr soliton (DKS) generation. Controllable interaction between stimulated Brillouin lasing and Kerr nonlinearity enhances the DKS coherence and mitigate the thermal instability challenge, achieving a remarkable 22-Hz intrinsic comb linewidth and an unprecedented phase noise of -180 dBc/Hz at 945 MHz carrier at free running. The schem…
In the development of topological photonics, achieving three dimensional topological insulators is of significant interest since it enables the exploration of new topological physics with photons, and promises novel photonic devices that are robust against disorders in three dimensions. Previous theoretical proposals towards three dimensional topological insulators utilize complex geometries that are challenging to implement. Here, based on the concept of synthetic dimension, we show that a two-dimensional array of ring resonators, which was previously demonstrated to exhibit a two-dimensional…
Many novel properties of non-Hermitian systems are found at or near the exceptional points-branch points of complex energy surfaces at which eigenvalues and eigenvectors coalesce. In particular, higher-order exceptional points can result in optical structures that are ultrasensitive to external perturbations. Here we show that an arbitrary order exceptional point can be achieved in a simple system consisting of identical resonators placed near a waveguide. Unidirectional coupling between any two chiral dipolar states of the resonators mediated by the waveguide mode leads to the exceptional poi…
We report that $> 80%$ of the photons generated inside a photonic crystal slab resonator can be funneled within a small divergence angle of $\pm 30^\circ$. The far-field radiation properties of a photonic crystal slab resonant mode are modified by tuning the cavity geometry and by placing a reflector below the cavity. The former method directly shapes the near-field distribution so as to achieve directional and linearly-polarized far-field patterns. The latter modification takes advantage of the interference effect between the original waves and the reflected waves to enhance the energy-direct…
Optical microresonators are of paramount importance in photonic circuits requiring fine spectral filtering or resonant light recirculation. Key performance metrics improve with increasing resonance quality factor (Q) across all applications. The performance of silicon photonic circuits is often hampered by the low-quality factor of planar silicon microresonators, typically of Q~10^4-10^5. On the other hand, bulk whispering gallery mode resonators provide a wide range of materials with intriguing optical properties and exceptionally high resonant quality factors Q>10^7. However, the efficient c…
Silicon photonics promises to alleviate the bandwidth bottleneck of modern day computing systems. But silicon photonic devices have the fundamental problem of being highly sensitive to ambient temperature fluctuations due to the high thermo-optic (TO) coefficient of silicon. Most of the approaches proposed to date to overcome this problem either require significant power consumption or incorporate materials which are not CMOS-compatible. Here we demonstrate a new class of optical devices which are passively temperature compensated, based on tailoring the optical mode confinement in silicon wav…
Whispering gallery modes are known for having orbital angular momentum, however the interplay of local spin density, orbital angular momentum, and the near-field interaction with quantum emitters is much less explored. Here, we study the spin-orbital interaction of a circularly polarized dipole with the whispering gallery modes (WGMs) of a spherical resonator. Using an exact dyadic Green's function approach, we show that the near-field interaction between the photonic spin of a circularly polarized dipole and the local spin density of whispering gallery modes gives rise to unidirectional behav…
Thermally-tuning silicon micro-cavities are versatile and beneficial elements in low-cost large-scale photonic integrated circuits (PICs). Traditional metal heaters used for thermal tuning in silicon micro-cavities usually need a thick SiO2 upper-cladding layer, which will introduce some disadvantages including low response speed, low heating efficiency, low achievable temperature and complicated fabrication processes. In this paper, we propose and experimentally demonstrate thermally-tuning silicon micro-disk resonators by introducing graphene transparent nano-heaters, which contacts the sili…
We develop and implement a new mathematical and computational framework for designing photonic elements with one or more high-$Q$ scattering resonances. The approach relies on solving for the poles of the scattering matrix, which mathematically amounts to minimizing the determinant of the Fredholm integral operator of the electric field with respect to the permittivity profile of the scattering element. We apply the method to design subwavelength gradient-permittivity structures with multiple scattering resonances and quality factors exceeding 500. We also find the spectral scattering cross se…
We report on mapping of the local density of states in L3 photonic crystal resonators (PCR) via deterministically positioned single Ge quantum dots (QDs). Perfect site-control of Ge QDs on pre-patterned silicon-on-insulator substrates was exploited to fabricate in one processing run almost 300 L3 PCRs containing single QDs in systematically varying positions in the cavities. The alignment precision of the QD emitters was better than 20 nm. This type of parallel processing is essentially based on standard Si device technologies and is therefore scalable to any number and configuration of PCR st…
Nonlinearity is a powerful determinant of physical systems. Controlling nonlinearity leads to interesting states of matter and new applications. In optics, diverse families of continuous and discrete states arise from balance of nonlinearity and group-velocity dispersion (GVD). Moreover, the dichotomy of states with locally enhanced or diminished field intensity depends critically on the relative sign of nonlinearity and either anomalous or normal GVD. Here, we introduce a resonator with unconditionally normal GVD and a single defect mode that supports both dark, reduced-intensity states and b…
Mode splitting induced by coherent optical mode interference in coupled resonant cavities is a key phenomenon in photonic resonators that can lead to powerful and versatile filtering functions, in close analogy to electromagnetically-induced-transparency, Autler-Townes splitting, Fano resonances, and dark states. It can not only break the dependence between quality factor, free spectral range, and physical cavity length, but can also lead to group delay response and mode interactions that are useful for enhancing light-material interaction and dispersion engineering in nonlinear optics. In thi…
