Using first principles calculations, we model the chemical vapor deposition (CVD) growth of carbon nanotubes (CNT) on nanoparticles of late transition (Ni, Pd, Pt) and coinage (Cu, Ag, Au) metals. The process is analyzed in terms of the binding of mono- and diatomic carbon species, their diffusion pathways, and the stability of the growing CNT. We find that the diffusion pathways can be controlled by the choice of the catalyst and the carbon precursor. Binding of the CNT through armchair edges is more favorable than through zigzag ones, but the relative stability varies significantly among the metals. Coinage metals, in particular Cu, are found to favor CVD growth of CNTs at low temperatures and with narrow chirality distributions.
We have developed a thermodynamic model of the catalytic growth of multiwall carbon nanotubes from hydrocarbon precursors at elevated temperature. Using this model we have computed the heat distribution, and carbon concentration in the catalyst. Calculations delivered a analytical formula for the growth time and growth rate. We find that the growth is mainly driven by a concentration gradient within the catalyst, rather than a temperature gradient.
We used microcontact printing to pattern a silicon surface with an iron-containing catalytic solution. Multi-wall carbon nanotubes were subsequently grown on the patterned areas by chemical vapor deposition at temperatures between 650 and 1000C. We demonstrate that the diameter of the catalytically grown multi-wall nanotubes increases with the deposition temperature. Raman spectroscopy has been used to investigate the crystalline character of the obtained structures and it is found that the fraction of the nano-crystalline shell increases with the temperatures. The measurement of the field emi…
We prepared three ferrite nanocatalysts: (i) copper ferrite (CuFe2O4), (ii) ferrite where cobalt was substituted by nickel (NixCo1-xFe2O4, with x= 0, 0.2, 0.4, 0.6), and (iii) ferrite where nickel was substituted by zinc (ZnyNi1-yFe2O4 with y= 1, 0.7, 0.5, 0.3), by the sol-gel method. The X-ray diffraction patterns show that the ferrite samples have been crystallized in the cubic spinel structural phase. We obtained the grain size by FE-SEM images in the range of 10-70 nm, and their magnetic properties by VSM. Next, carbon nanotubes were grown on these nanocatalysts by the CCVD method. We show…
Three different catalysts (Fe, Ni, Co nitrates dissolved in ethanol) were patterned on a SiO2/Si substrate and multi-wall carbon nanotubes were grown by catalytic decomposition of acetylene. We compare the growth of the carbon nanostructures in the temperature range between 580C and 1000C. With our experimental set-up the catalyst solutions of cobalt and nickel were found to be less efficient than the one of iron. An optimal production of multi-wall nanotubes was observed at temperatures between 650C and 720C with the iron solution as catalyst. We found a tendency towards thicker structures wi…
In the present work, extended Argon ion bombardment was used to modify anatase TiO2 nanotube (NTs) layers. In situ X-ray photoelectron spectroscopy revealed a high content of sub-oxide formed (Ti3+, Ti2+ states) in the nanotube layers. These samples were tested for their ability to show open-circuit photocatalytic hydrogen evolution. We found for UV (cw laser 325nm) illumination as well as for AM1.5 conditions, a strongly enhanced H2 evolution activity in absence of the usual noble metal-nanoparticle decoration. We conclude therefore that these sub-oxide states can play an important role in th…
The nucleation of carbon nanotubes on small nickel clusters is studied using a tight binding model coupled to grand canonical Monte Carlo simulations. This technique closely follows the conditions of the synthesis of carbon nanotubes by chemical vapor deposition. The possible formation of a carbon cap on the catalyst particle is studied as a function of the carbon chemical potential, for particles of different size, either crystalline or disordered. We show that these parameters strongly influence the structure of the cap/particle interface which in turn will have a strong effect on the contro…
In most envisioned applications, full utilization of a graphene-carbon nanotube (CNT) construct requires maintaining the integrity of the graphene layer during the CNT growth step. In this work, we exhibit an approach towards controlled CNT growth atop graphene substrates where the reaction equilibrium between source hydrocarbon decomposition and carbon saturation into and precipitation from the catalyst nanoparticles shifts towards CNT growth rather than graphene consumption. By utilizing C2H4 feedstock, we demonstrate that the low temperature growth permissible with this gas suppresses undes…
The nucleation of carbon caps on small nickel clusters is studied using a tight binding model coupled to grand canonical Monte Carlo simulations. It takes place in a well defined carbon chemical potential range, when a critical concentration of surface carbon atoms is reached. The solubility of carbon in the outermost Ni layers, that depends on the initial, crystalline or disordered, state of the catalyst and on the thermodynamic conditions, is therefore a key quantity to control the nucleation.
Addition of only 1% of acetylene into ethanol was found to enhance the growth rate of singlewalled carbon nanotubes (SWNTs) by up to ten times. Since acetylene is a byproduct of the thermal decomposition of ethanol, this suggests an alternative fast reaction pathway to the formation of SWNTs from ethanol via byproducts of decomposition. This accelerated growth, however, only occurred in the presence of ethanol, whereas pure acetylene at the same partial pressure resulted in negligible growth and quickly deactivated the catalyst. The dormant catalyst could be revived by reintroduction of ethano…
Chirality-selected single-walled carbon nanotubes (SWCNTs) ensure a great potential of building ~1 nm sized electronics. However, the reliable method for chirality-selected SWCNT is still pending. Here we present a theoretical study on the SWCNT's chirality assignment and control during the catalytic growth. This study reveals that the chirality of a SWCNT is determined by the kinetic incorporation of the pentagon formation during SWCNT nucleation. Therefore, chirality is randomly assigned on a liquid catalyst surface. Furthermore, based on the understanding, two potential methods of synthesiz…
Hybrid systems composed of the reduced graphene oxide-supported platinum and multiwall carbon nanotubes-supported iridium (both noble metals utilized at low loadings on the level of 15 and < 5 microg cm-2, respectively) have been considered as catalytic materials for the reduction of oxygen in acid media (0.5 mol dm-3 H2SO4). The electrocatalytic activity toward reduction of oxygen and formation of hydrogen peroxide intermediate have been tested using rotating ring-disk electrode voltammetric experiments. The efficiency of the proposed catalytic systems has also been addressed by performing ga…
We develop a new chemical route to prepare carbon nanotubes at room temperature. Graphite powder is immersed in a mixed solution of nitric and sulfuric acid with potassium chlorate. After heating the solution up to 70°C and leaving them in the air for 3 days, we obtained carbon nanotube bundles. This process could provide an easy and inexpensive method for the preparation of carbon nanotubes.
We report on the nano-electron beam assisted fabrication of atomically sharp iron-based tips and on the creation of a nano-soldering iron for nano-interconnects using Fe-filled multiwalled carbon nanotubes (MWCNTs). High energy electron beam machining has been proven a powerful tool to modify desired nanostructures for technological applications and to form molecular junctions and interconnections between carbon nanotubes. Recent studies showed the high degree of complexity in the creation of direct interconnections between multiwalled and CNTs having dissimilar diameters. Our technique allows…
Using the first-principles spin density functional approach, we have studied magnetism of a new type of all-carbon nanomaterials, i.e., the carbon nanowires inserted into the single-walled carbon nanotubes. It is found that if the 1D carbon nanowire density is not too higher, the ferromagnetic ground state will be more stable than the antiferromagnetic one, which is caused by weak coupling between the 1D carbon nanowire and the single-walled carbon nanotube. Also, both dimerization of the carbon nanowire and carbon vacancy on the tube-wall are found to enhance the magnetic moment of the compos…
We show that the presence of electrically insulating graphite oxide (GO) within a single wall carbon nanotube network strongly enhances electrical conductivity, whereas reduced graphite oxide, even though electrically conductive, suppresses electrical conductivity within a composite network with single wall carbon nanotubes. Measurements of Young modulus and of Raman spectra strongly support our interpretation of the indirect role of the oxide groups, present in graphite oxide within the single wall carbon nanotubes/graphite oxide composite, through electronic doping of metallic single wall ca…
In this paper the new concept of super-bridges, i.e. kilometre-long bridges suspended over carbon nanotube cables, is introduced. The analysis shows that the use of realistic (thus defective) carbon nanotube bundles as suspension cables can enlarge the current limit main span by a factor of 3.
First-principles simulations were performed to investigate reaction of carbon nanotubes with adsorbed metal atoms. Mechanical modification of their structures enhances chemical reactivity of carbon nanotubes. Adsorption of a tungsten, tantalum, or niobium atom on a (5, 0) nanotube with a Stone-Wales defect was shown to have characteristically strong chemisorption. Bond-breaking in the carbon-carbon network and formation of a local metal-carbon complex were observed during the simulation. Adsorption of W, Ta, Ni or Mo on a twisted (5, 0) nanotube showed a preferred breaking of several bonds, ev…
We show that separating metallic from semiconducting carbon nanotubes by dielectrophoresis is developing towards a bulk separation method, which allows for the first time to produce thin films of only metallic single-walled carbon nanotubes and to measure their optical absorption spectra. The data proofs that the selectivity of the separation scheme is independent from the nanotube diameter.
We have fabricated field effect transistors from carbon nanotubes using a novel selective placement scheme. We use carbon nanotubes that are covalently bound to molecules containing hydroxamic acid functionality. The functionalized nanotubes bind strongly to basic metal oxide surfaces, but not to silicon dioxide. Upon annealing, the functionalization is removed, restoring the electronic properties of the nanotubes. The devices we have fabricated show excellent electrical characteristics.
Fundamentally new families of carbon single walled nanotubes are proposed. These nanotubes, called graphynes, result from the elongation of covalent interconnections of graphite-based nanotubes by the introduction of yne groups. Similarly to ordinary nanotubes, arm-chair, zig-zag, and chiral graphyne nanotubes are possible. Electronic properties, predicted using tight-binding and ab initio density functional methods, show a rich variety of metallic and semiconducting behaviors.
The weak-chemisorption/charge-transfer picture for adsorption of aromatic molecules over carbon nanotubes, proposed in the commented paper, is criticized.
We calculate the van der Waals energy of a C60 molecule when it is encapsulated in a single-walled carbon nanotube with discrete atomistic structure. orientational degrees of freedom and longitudinal displacements of the molecule are taken into account, and several achiral and chiral carbon nanotubes are considered. A comparison with earlier work where the tube was approximated by a continuous cylindrical distribution of carbon atoms is made. We find that such an approximation is valid for high and intermediate tube radii; for low tube radii, minor chirality effects come into play. Three molec…
Electronic and optoelectronic devices based on thin films of carbon nanotubes are currently limited by the presence of metallic nanotubes. Here we present a novel approach based on nanotube alkyl functionalization to physically remove the metallic nanotubes from such network devices. The process relies on preferential thermal desorption of the alkyls from the semiconducting nanotubes and the subsequent dissolution and selective removal of the metallic nanotubes in chloroform. The approach is versatile and is applied to devices post-fabrication.
Metal catalysts supporting the growth of Single Wall Carbon Nanotubes display different carbon solubilities and chemical reactivities. In order to specifically assess the role of carbon solubility, we take advantage of the physical transparency of a tight binding model established for Ni-C alloys, to develop metal carbon models where all properties, except carbon solubility, are similar. These models are used to analyze carbon incorporation mechanisms, modifications of metal / carbon wall interfacial properties induced thereby, and the associated nanotube growth mechanisms. Fine tuning carbon …
Carboxylic functionalization (-COOH groups) of carbon nanotubes is known to improve their dispersion properties and increase the electrical conductivity of carbon-nanotube - polymer nanocomposites. We have studied experimentally the effects of this type of functionalization on the thermal conductivity of the nanocomposites. It was found that while even small quantities of carbon nanotubes (~1 wt%) can increase the electrical conductivity, a larger loading fraction (~3 wt%) is required to enhance the thermal conductivity of nanocomposites. Functionalized multi-wall carbon nanotubes performed th…
MD simulations based on an empirical potential energy surface were used to study the nucleation of bamboo-like carbon nanotubes (BCNTs). The simulations reveal that inner walls of the bamboo structure start to nucleate at the junction between the outer nanotube wall and the catalyst particle. In agreement with experimental results, the simulations show that BCNTs nucleate at higher dissolved carbon concentrations (i.e., feedstock pressures) than those where non-bamboolike carbon nanotubes are nucleated.
Large-scale fully interconnected ring carbon nanotube (CNT) networks were first prepared using thermo chemical vapor deposition in nano-channel network templates of porous anodic alumina. This conductive CNT network film consists of billions of nanotube segments with a single layer, and could be made as large as the centimeter size of the template, with a uniform two-dimensional ring topological structure. These CNT networks could be grown from tiny Fe/Co catalyst particles which were electro-deposited into the templates, or totally without additional metallic catalysts. The common interconnec…
A simple method to disperse individual single walled carbon nanotubes (SWCNT ) on an atomically flat substrate is presented. Proper tuning of ac modes of atomic force microscopes(AFM) is discussed. This is needed to discriminate between individual nanotubes and very small bundles. The distribution of lengths of the nanotubes measured by these methods is reported.
The lattice specific heat of carbon nanotubes is evaluated within the microscopic model proposed by Mahan and Jeon, published in the Physical Review B, in 2004. Phonons are considered for a single wall carbon nanotube in the armchair configuration. As expected, low temperature and high temperature regions show different behavior of specific heat. Carbon nanotubes are also displaying a very interesting lattice transport depending on the diameter, with a rather high thermal conductivity for small diameters.
Classical molecular dynamics (MD) simulations employing Brenner potential for intra-nanotube interactions and Van der Waals forces for polymer-nanotube interfaces are used to invetigate the thermal expansion and diffusion characteristics of carbon nanotube-polyethylene composites. Additions of carbon nanotubes to polymer matrix are found to increase the glass transition temperature Tg, and thermal expansion and diffusion coefficients in the composite above Tg. These findings could have implications in CNT composite processing, coating and painting applications.
This letter gives a credit to a pioneering paper that is almost unknown to scientific community. On the basis of Transmission Electron Microscopy images and X-ray Ray Diffraction patterns of carbon multi-layer tubular crystals the authors suggested a model of nanotube structure formation and hypothesis on various chirality of carbon nanotubes.
A novel method is developed to enable the formation, positioning and patterning of individual metal nano-clusters with controllable and monodispersed sizes down to 1-2 nm-scale. Among wide range of potential applications, the nanoparticle arrays are used for deterministic synthesis of monodispersed single walled carbon nanotubes. The carbon nanotubes are grown at individually controlled locations with near one-to-one yield, reaching one of the ultimate goals of nanotube synthesis.
Exploring the synthesis of novel molecular nanostructures has been in the forefront of material research in the last decade. One of the most interesting nanostructures are single wall carbon nanotubes (SWCNTs). Their catalyst free growth, however, remains an elusive goal. Here, we present the growth of single wall carbon nanotubes from organic solvents such as benzene and toluene in a confined environment, inside a host SWCNT. The solvents encapsulated in SWCNTs are transformed to an inner tube when subject to a heat treatment under dynamic vacuum at 1270 $^{\circ}$C. We used isotope labeling …
We predict new forms of carbon consisting of one and two dimensional networks of interlinked single wall carbon nanotubes, some of which are energetically more stable than van der Waals packing of the nanotubes on a hexagonal lattice. These interlinked nanotubes are further transformed with higher applied external pressures to more dense and complicated stable structures, in which curvature-induced carbon sp$^{3}$ re-hybridizations are formed. We also discuss the energetics of the bond formation between nanotubes and the electronic properties of these predicted novel structures.
Novel applications in nanotechnology rely on the design of tailored nano-architectures. For this purpose, carbon nanotubes and nanoparticles are intensively investigated. In this work we study the influence of non-functionalized carbon nanotubes on the synthesis of CdSe nanoparticles by means of organometallic colloidal routes. This new synthesis methodology does not only provide an effective path to attach nanoparticles non-covalently to carbon nanotubes but represents also a new way to control the shape of nanoparticles.
We use a multiscale procedure to derive a simple continuum model of multiwalled carbon nanotubes that takes into account both strong covalent bonds within graphene layers and weak bonds between atoms in different layers. The model predicts polygonization of crossections of large multiwalled nanotubes as a consequence of their curvature-induced turbostratic structure.
Persistent currents in rings constructed from carbon nanotubes are investigated theoretically. After studying the contribution of finite temperature or quenched disorder on covalent rings, the complexity due to the bundle packing is addressed. The case of interacting nanotori and self-interacting coiled nanotubes are analyzed in details in relation with experiments.
We theoretically compute the interface thermal resistance between crossing single walled carbon nanotubes of various chiralities, using an atomistic Green's function approach with semi-empirical potentials. The results are then used to model the thermal conductivity of three dimensional nanotube pellets in vacuum. For an average nanotube length of 1 $μ$m, the model yields an upper bound for the thermal conductivity of densely compacted pellets, of the order of a few W/m-K. This is in striking contrast with the ultra-high thermal conductivity reported on individually suspended nanotubes. The re…
A new group-theory method to relate a spectrum of carbon nanotubes with that of a graphene monolayer is elaborated. The spectrum reconstruction is performed using a virtual intermediate planar periodic structure. Selected irreducible representations of its space symmetry group and all those of the nanotube one are isomorphic and therefore span the correlated excitations. The method is applied to study the origin of the zone-center phonon modes of chiral and achiral carbon nanotubes. The structure of the G-band for particular types of nanotubes is determined. The results obtained could be usefu…
The analytical expressions for the van der Waals potential energy and force between two crossed carbon nanotubes are presented. The Lennard-Jones potential for two carbon atoms and the method of the smeared out approximation suggested by L.A. Girifalco were used. The exact formula is expressed in terms of rational and elliptical functions. The potential and force for carbon nanotubes were calculated. The uniform potential curves for single- and multi- wall nanotubes were plotted. The equilibrium distance, maximal attractive force, and potential energy have been estimated.
Nitrogen doped single wall carbon nanotubes have many functional benefits. Doping opens the possibility to control the electronic energy levels, surface energy, surface reactivity and charge carrier density. The additional electron in the outer shell changes the electronic properties of the nanotubes when introduced into the carbon lattice. Here we present the latest findings in the in-situ doping during synthesis of single wall carbon nanotubes using caffeine as a precursor of both carbon and nitrogen. A special furnace with two heating elements allowed us to sublimate and decompose the solid…
The first order phase transition of a water cluster confined in a dynamic single-walled carbon nanotube is investigated using a classical molecular dynamics (MD) method. The formation of ice-nanotube is monitored through the structure factor and potential energies. The transition temperature and its diameter dependence obtained by the simulations agree well with those of previously reported experiments. The transition temperature of the ice-nanotube was shown to take a maximum value of around room temperature with the number of the ring members n=5. Potential energy contribution to the phase c…
We performed ab initio calculation on the pristine and carbon-doped (5,5) and (9,0) BN nanotubes. It was found that Carbon substitution for either boron or nitrogen in BN nanotubes can induce spontaneous magnetization. Calculations based on density functional theory with the local-spin-density-approximation on the electronic band structure revealed a spin polarized, dispersionless band near the Fermi energy. The magnetization can be attributed to the carbon 2p electron. Compared to other theoretical models of light-element or metal-free magnetic materials, the Carbon-doped BN nanotubes are mor…
We use ab initio density functional calculations to study the chemical functionalization of single-wall carbon nanotubes and graphene monolayers by silyl (SiH3) radicals and hydrogen. We find that silyl radicals form strong covalent bonds with graphene and nanotube walls, causing local structural relaxations that enhance the sp3 character of these graphitic nanostructures. Silylation transforms all carbon nanotubes into semiconductors, independent of their chirality. Calculated vibrational spectra suggest that specific frequency shifts can be used as a signature of successful silylation.
We have computed the adsorption of Krypton in a closed single-walled carbon nanotube using the method of Grand Canonical Monte Carlo. Our results indicate evidence of an incommensurate solid formed at high pressure and low temperature (T<85K), before the formation of a second layer. The solid melts above that temperature. Our simulations are in good agreement with novel experimental results for adsorption in individual carbon nanotubes.
The poor thermal conductivity of bulk polymers may be enhanced by combining them with high thermal conductivity materials such as carbon nanotubes. Different from random doping, we find that the aligned carbon nanotube-polyethylene composites (ACPCs) has a high thermal conductivity by non-equilibrium molecular dynamics simulations. The analyses indicate that the aligned structure can not only take advantage of the high thermal conduction of carbon nanotubes, but enhance thermal conduction of polyethylene (PE) chains. Our predictions may inspire manufacturing aligned polymer-based composites fo…
We investigate the field emission properties of nitrogenated and boronated carbon nanotubes using time-dependent density functional theory, were the wave function propagation is performed using the Crank-Nicholson algorithm. We extract the current-voltage characteristics of the emitted electrons from nanotubes with different doping configurations. We found that boron doping either impedes, or slightly enhances, field emission. Nitrogen strongly influences the emission current, and the current is sensitive to the location of the nitrogen dopant in the nanotube. The emitted charge cloud from nit…
In an attempt to understand why catalytic methods for the growth of boron nitride nanotubes work much worse than for their carbon counterparts, we use first-principles calculations to study the energetics of elemental reactions forming N2, B2 and BN molecules on an iron catalyst. We observe that in the case of these small molecules, the catalytic activity is hindered by the formation of B2 on the iron surface. We also observe that the local morphology of a step edge present in our nanoparticle model stabilizes the boron nitride molecule with respect to B2 due to the ability of the step edge to…
We fabricated cantilevers for magnetic force microscopy with carbon nanotube tips coated with magnetic material. Images of a custom hard drive demonstrated 20 nm lateral resolution, with prospects for further improvements.
Process of vapor pyrolytic deposition of carbon on nickel and cobalt-containing ordered mesoporous MCM-41 matrices at decomposition of acetylene have been investigated. Formation of nanotubes, nanowires and amorphous carbon particles depending pyrolysis conditions is observed.
The stability of a single-walled carbon nanotube placed on top of a catalytic nickel nanoparticle is investigated by means of molecular dynamics simulations. As a case study, we consider the $(12,0)$ nanotube consisting of 720 carbon atoms and the icosahedral Ni$_{309}$ cluster. An explicit set of constant-temperature simulations is performed in order to cover a broad temperature range from 400 to 1200 K, at which a successful growth of carbon nanotubes has been achieved experimentally by means of chemical vapor deposition. The stability of the system depending on parameters of the involved in…
Carbon nanotubes have emerged as a possible new material for electronic applications. They show promising characteristics for transistors as well as for interconnects. Here we review their basic properties and focus on the status of nanotubes with respect to their application as interconnects and discuss the challenges facing their integration.
We analyze two scattering mechanisms that might cause intrinsic electronic resistivity in multi-wall carbon nanotubes: scattering by dopant impurities, and scattering by inter-tube electron-electron interaction. We find that for typically doped multi-wall tubes backward scattering at dopants is by far the dominating effect.
The crystallographic structure of CdSe nanoparticles attached to carbon nanotubes has been elucidated by means of high resolution transmission electron microscopy and high angle annular dark field scanning transmission electron microscopy tomography. CdSe rod-like nanoparticles, grown in solution together with carbon nanotubes, undergo a morphological transformation and become attached to the carbon surface. Electron tomography reveals that the nanoparticles are hexagonal-based with the (001) planes epitaxially matched to the outer graphene layer.
We present the first-principles study of effects of the charge dopants such as Cesium and Iodine encapsulated on the electronic structure of carbon nanotubes. An encapsulated cesium atom donates an electron to the nanotube and produces donor-like states below the conduction bands. In contrast, an iodine trimer (I$_{3}$) accepts an electron from the nanotube and produces an acceptor-like state above the valance band maximum. We find that a Cs atom inside a metallic armchair carbon nanotube gives rise to spatial oscillations of the density of states near the Fermi level.
Team C2CNT, or team Carbon dioxide to carbon nanotubes, proprietary technology directly removes the widest range of carbon dioxide from the ecosystem. C2CNT technology simply transforms low to high carbon dioxide into carbon and oxygen, and the carbon produced is permanently removed, that is stable on the order of geologic time frames. C2CNT technology directly removes, transforms and stores atmospheric 0.04% CO2 without pre-concentration from the air, or 5% CO2 removal of gas power plant CO2 emissions, or 12.5% CO2 removal of coal power plant CO2 emissions, or 33% CO2 (pertinent to the comple…
Tweaking the properties of carbon nanotubes is a prerequisite for their practical applications. Here we demonstrate fine-tuning the electronic properties of single-wall carbon nanotubes via filling with ferrocene molecules. The evolution of the bonding and charge transfer within the tube is demonstrated via chemical reaction of the ferrocene filler ending up as secondary inner tube. The charge transfer nature is interpreted well within density functional theory. This work gives the first direct observation of a fine-tuned continuous amphoteric doping of single-wall carbon nanotubes.
We present a detailed electron diffraction study of individual single-walled carbon nanotubes. A novel sample preparation procedure provides well-separated, long and straight individual single-shell nanotubes. Diffraction experiments are carried out at 60kV, below the threshold for knock-on damage in carbon nanotubes. We describe experimental parameters that allow single-tube electron diffraction experiments with widely available thermal emission transmission electron microscopes. Further, we review the simulation of diffraction patterns for these objects.
