Using a test TPC, consisting of the ALICE TPC field cage prototype in combination with the final ALICE TPC readout and electronics, the energy loss distribution and resolution were measured for identified protons. The measurements were compared to theoretical calculations and good quantitative agreement was found when detector effects were taken into account. The implications for particle identification are discussed.
The extraction and optimisation of the ALTRO Parameters out of the ALICE TPC data is described, including the performance measurment of this set. The ion tail of a signal pulse and the variation is firstly measured and quantified.
The ALICE High-Level Trigger processes data online, to either select interesting (sub-) events, or to compress data efficiently by modeling techniques. Focusing on the main data source, the Time Projection Chamber, the architecure of the system and the current state of the tracking and compression methods are outlined.
A large Time Projection Chamber (TPC) is the main device for tracking and charged-particle identification in the ALICE experiment at the CERN LHC. After the second long shutdown in 2019-2020, the LHC will deliver Pb beams colliding at an interaction rate of up to 50 kHz, which is about a factor of 50 above the present readout rate of the TPC. To fully exploit the LHC potential, the TPC readout chambers will be upgraded with Gas Electron Multiplier (GEM) technology. To assure stable behaviour of the upgraded chambers in the harsh LHC environment, a dedicated R&D programme was launched in order …
ALICE (A Large Heavy Ion Experiment) is one of the four major experiments at the Large Hadron Collider (LHC) at CERN, which is today the most powerful particle accelerator worldwide. The High Level Trigger (HLT) is an online compute farm of about 200 nodes, which reconstructs events measured by the ALICE detector in real-time. The HLT uses a custom online data-transport framework to distribute data and workload among the compute nodes. ALICE employs several calibration-sensitive subdetectors, e.g. the TPC (Time Projection Chamber). For a precise reconstruction, the HLT has to perform the calib…
In the upcoming LHC Run 3, starting in 2021, the upgraded Time Projection Chamber (TPC) of the ALICE experiment will record minimum bias Pb-Pb collisions in a continuous readout mode at an interaction rate up to 50 kHz. This corresponds to typically 4-5 overlapping collisions during the electron drift time in the detector. Despite careful tuning of the new quadruple GEM-based readout chambers, which fulfill the design requirement of an ion backflow below 1%, these conditions will lead to space-charge distortions of several centimeters that fluctuate in time. They will be corrected via a calibr…
The Time Projection Chamber of the ALICE experiment at the CERN Large Hadron Collider features highly integrated on-detector read-out electronics. It is following the general trend of high energy physics experiments by placing the front-end electronics as close to the detector as possible -- only some 10 cm away from its active volume. Being located close to the beams and the interaction region, the electronics is subject to a moderate radiation load, which allowed us to use commercial off-the-shelf components. However, they needed to be selected and qualified carefully for radiation hardness …
In LHC Run 3, ALICE will increase the data taking rate significantly to 50 kHz continuous read-out of minimum bias Pb-Pb collisions. The reconstruction strategy of the online-offline computing upgrade foresees a first synchronous online reconstruction stage during data taking enabling detector calibration and data compression, and a posterior calibrated asynchronous reconstruction stage. Many new challenges arise, among them continuous TPC read-out, more overlapping collisions, no a priori knowledge of the primary vertex and of location-dependent calibration in the synchronous phase, identific…
In LHC Run 3, ALICE will increase the data taking rate significantly to continuous readout of 50 kHz minimum bias Pb-Pb collisions. The reconstruction strategy of the online offline computing upgrade foresees a first synchronous online reconstruction stage during data taking enabling detector calibration, and a posterior calibrated asynchronous reconstruction stage. We present a tracking algorithm for the Time Projection Chamber (TPC), the main tracking detector of ALICE. The reconstruction must yield results comparable to current offline reconstruction and meet the time constraints like in th…
ALICE (A Large Ion Collider Experiment) is one of four major experiments at the Large Hadron Collider (LHC) at CERN. The High Level Trigger (HLT) is a compute cluster, which reconstructs collisions as recorded by the ALICE detector in real-time. It employs a custom online data-transport framework to distribute data and workload among the compute nodes. ALICE employs subdetectors sensitive to environmental conditions such as pressure and temperature, e.g. the Time Projection Chamber (TPC). A precise reconstruction of particle trajectories requires the calibration of these detectors. Performing …
A Time Projection Chamber (TPC) is a powerful detector for 3-dimensional tracking and particle identification for ultra-high multiplicity events. It is the central tracking device of many experiments, e.g. the ALICE experiment at CERN. The necessity of a switching electrostatic gate, which prevents ions produced in the amplification region o MWPCs from entering the drift volume, however, restricts its application to trigger rates of the order of 1 kHz. Charge amplification by Gas Electron Multiplier (GEM) foils instead of proportional wires offers an intrinsic suppression of the ion backflow, …
The ALICE Collaboration is planning a major upgrade of its central barrel detectors to be able to cope with the increased LHC luminosity beyond 2020. In order to record at an increased interaction rate of up to 50$\,$kHz in Pb$-$Pb collisions, the TPC will be operated in an ungated mode with continuous readout. This demands for a replacement of the currently employed gated Multi-Wire Proportional Chambers by GEM-based (Gas Electron Multiplier) readout chambers, while retaining the performance in particular in terms of particle identification capabilities via the measurement of the specific ene…
The ALICE experiment will run with continuous readout at interaction rates of up to 50 kHz in Pb-Pb collisions during Run 3 of the LHC. In order to achieve this goal, a new data processing scheme and software are developed. This scheme strongly relies on GPUs (Graphics Processing Unit) for fast online and offline calibration and reconstruction as well as on efficient data compression. On the hardware side, the Time Projection Chamber (TPC), among other detector systems, received major upgrades to its readout chambers and readout electronics. The multiwire proportional chambers were replaced by…
The ALICE (A Large Ion Collider Experiment) experiment at the Large Hadron Collider (LHC) at CERN is dedicated to heavy ion physics to explore the structure of strongly interacting matter. The Time Projection Chamber (TPC) of ALICE is a tracking detector located in the central region of the experiment. It offers excellent tracking capabilities as well as particle identification. After the second long shutdown (LS2) the LHC will run at substantially higher luminosities. To be able to increase the data acquisition rate by a factor of 100, the ALICE TPC experiment has to replace the Multi-Wire Pr…
After the Long Shutdown 2 the LHC will provide lead-lead collisions at interaction rates as high as 50kz. In order to cope with such conditions the ALICE Time Projection Chamber (TPC) needs to be upgraded. After the upgrade the TPC will run in a continuous mode, without any degradation of the momentum and dE/dx resolution compared to the performance of the present TPC. Since readout by multi-wire proportional chambers is no longer feasible with these requirements, new technologies have to be employed. In the new readout chambers the electron amplification is provided by a stack of four Gas Ele…
The online event reconstruction for the ALICE experiment at CERN requires processing capabilities to process central Pb-Pb collisions at a rate of more than 200 Hz, corresponding to an input data rate of about 25 GB/s. The reconstruction of particle trajectories in the Time Projection Chamber (TPC) is the most compute intensive step. The TPC online tracker implementation combines the principle of the cellular automaton and the Kalman filter. It has been accelerated by the usage of graphics cards (GPUs). A pipelined processing allows to perform the tracking on the GPU, the data transfer, and th…
A large Time Projection Chamber (TPC) is the main device for tracking and charged-particle identification in the ALICE experiment at the CERN LHC. After the second long shutdown in 2019-2020, the LHC will deliver Pb beams colliding at an interaction rate up to 50 kHz, which is about a factor of 100 above the present read-out rate of the TPC. To fully exploit the LHC potential the TPC will be upgraded based on the Gas Electron Multiplier (GEM) technology. A prototype of an ALICE TPC Outer Read-Out Chamber (OROC) was equipped with twelve large-size GEM foils as amplification stage to demonstrate…
In this paper the PreAmplifier ShAper (PASA) for the Time Projection Chamber (TPC) of the ALICE experiment at LHC is presented. The ALICE TPC PASA is an ASIC that integrates 16 identical channels, each consisting of Charge Sensitive Amplifiers (CSA) followed by a Pole-Zero network, self-adaptive bias network, two second-order bridged-T filters, two non-inverting level shifters and a start-up circuit. The circuit is optimized for a detector capacitance of 18-25 pF. For an input capacitance of 25 pF, the PASA features a conversion gain of 12.74 mV/fC, a peaking time of 160 ns, a FWHM of 190 ns, …
The ALICE Collaboration is planning a major upgrade of its central barrel detectors to be able to cope with the increased LHC luminosity beyond 2020. For the TPC, this implies a replacement of the currently used gated MWPCs (Multi-Wire Proportional Chamber) by GEM (Gas Electron Multiplier) based readout chambers. In order to prove, that the present particle identification capabilities via measurement of the specific energy loss are retained after the upgrade, a prototype of the ALICE IROC (Inner Readout Chamber) has been evaluated in a test beam campaign at the CERN PS. The d$E$/d$x$ resolutio…
ALICE will increase the data-taking rate for Run 3 significantly to 50 kHz continuous readout of minimum bias Pb--Pb collisions. The foreseen reconstruction strategy consists of 2 phases: a first synchronous online reconstruction stage during data-taking enabling detector calibration, and a posterior calibrated asynchronous reconstruction stage. The main challenges include processing and compression of 50 times more events per second than in Run 2, sophisticated compression and removal of TPC data not use for physics, tracking of TPC data in continuous readout, the TPC space-charge distortion …
The design, construction, and commissioning of the ALICE Time-Projection Chamber (TPC) is described. It is the main device for pattern recognition, tracking, and identification of charged particles in the ALICE experiment at the CERN LHC. The TPC is cylindrical in shape with a volume close to 90 m^3 and is operated in a 0.5 T solenoidal magnetic field parallel to its axis. In this paper we describe in detail the design considerations for this detector for operation in the extreme multiplicity environment of central Pb--Pb collisions at LHC energy. The implementation of the resulting requiremen…
ALICE (A Large Heavy Ion Experiment) is one of the four large scale experiments at the Large Hadron Collider (LHC) at CERN. The High Level Trigger (HLT) is an online computing farm, which reconstructs events recorded by the ALICE detector in real-time. The most compute-intense task is the reconstruction of the particle trajectories. The main tracking devices in ALICE are the Time Projection Chamber (TPC) and the Inner Tracking System (ITS). The HLT uses a fast GPU-accelerated algorithm for the TPC tracking based on the Cellular Automaton principle and the Kalman filter. ALICE employs gaseous s…
The ALICE experiment at the Large Hadron Collider at CERN is upgrading its central tracking detector, the Time Projection Chamber (TPC). The installation is foreseen during the second long shutdown of the Large Hadron Collider. The upgrade includes the complete exchange of the present MWPC readout chambers (ROC) with new ones based on Gas Electron Multiplier detectors. This is necessary due to the higher LHC luminosity and thus higher interaction rate. The new ROCs allow for continuous readout at 50 kHz compared to 500 Hz of the gated MWPC readout, while maintaining the particle identification…
The ALICE experiment at the Large Hadron Collider (LHC) proposes major detector upgrades to fully exploit the increase of the luminosity of the LHC in RUN~3 and to extend the physics reach for rare probes at low transverse momentum. The Time Projection Chamber (TPC) is one of the main tracking and PID devices in the central barrel of ALICE. The maximum trigger rate of the TPC is currently limited to about 3.5 kHz by the operation of a gating grid system. In order to make full use of the luminosity in RUN 3, the TPC is foreseen to be operated in an ungated mode with continuous readout. The exis…
In LHC Run 3, ALICE will increase the data taking rate significantly to 50 kHz continuous readout of minimum bias Pb--Pb collisions. The reconstruction strategy of the online-offline computing upgrade foresees a first synchronous online reconstruction stage during data taking enabling detector calibration, and a posterior calibrated asynchronous reconstruction stage. The main challenges include processing and compression of 50 times more events per second than in Run 2, identification of removable TPC tracks and hits not used for physics, tracking of TPC data in continuous readout, the TPC spa…
The Time Projection Chamber is the main tracking and particle identification detector of the ALICE experiment. The high luminosities delivered by the CERN LHC in Run 2 (2015-2018) posed new challenges in terms of detector performance and efficiency. The hardware components and calibration software were optimized and further developed to meet those challenges and maximize the quality of the data. In addition, unexpectedly large local distortions of the drift paths of ionization electrons have been observed at the edges of specific readout chambers. These distortions are caused by ions which ori…
ALICE is the dedicated heavy-ion experiment at the CERN Large Hadron Collider (LHC). Its main tracking and particle-identification detector is a large volume Time Projection Chamber (TPC). The TPC has been designed to perform well in the high-track density environment created in high-energy heavy-ion collisions. In this proceeding, we describe the track reconstruction procedure in ALICE. In particular, we focus on the two main challenges that were faced during the Run 2 data-taking period (2015--2018) of the LHC, which were the baseline fluctuations and the local space charge distortions in th…
Time Projection Chamber (TPC) has been chosen as the main tracking system in several high-flux and high repetition rate experiments. These include on-going experiments such as ALICE and future experiments such as PANDA at FAIR and ILC. Different $\mathrm{R}\&\mathrm{D}$ activities were carried out on the adoption of Gas Electron Multiplier (GEM) as the gas amplification stage of the ALICE-TPC upgrade version. The requirement of low ion feedback has been established through these activities. Low ion feedback minimizes distortions due to space charge and maintains the necessary values of detecto…
The ALICE High Level Trigger has to process data online, in order to select interesting (sub)events, or to compress data efficiently by modeling techniques.Focusing on the main data source, the Time Projection Chamber (TPC), we present two pattern recognition methods under investigation: a sequential approach "cluster finder" and "track follower") and an iterative approach ("track candidate finder" and "cluster deconvoluter"). We show, that the former is suited for pp and low multiplicity PbPb collisions, whereas the latter might be applicable for high multiplicity PbPb collisions, if it turns…
In LHC Run 3, ALICE will increase the data taking rate significantly, from an approximately 1 kHz trigger readout in minimum-bias Pb--Pb collisions to a 50 kHz continuous readout rate. The reconstruction strategy of the online-offline computing upgrade foresees a synchronous online reconstruction stage during data taking, which generates the detector calibration, and a posterior calibrated asynchronous reconstruction stage. The huge amount of data requires a significant compression in order to store all recorded events. The aim is a factor 20 compression of the TPC data, which is one of the ma…
The ALICE (A Large Ion Collider Experiment) Time Projection Chamber (TPC) at CERN LHC is presently equipped with Multi Wire Proportional Chambers (MWPCs). A gating grid prevents ions produced during the gas amplification from moving into the drift volume. The maximum drift time of the electrons together with the closure time of the gating grid allows a maximum readout rate of about 3 kHz. After the Long Shutdown 2 (from 2021 onwards), the LHC will provide lead-lead collisions at an expected interaction rate of 50 kHz. To take data at this rate the TPC will be upgraded with new readout chambers…
A new type of Time Projection Chamber (TPC) has been proposed for the upgrade of the ALICE (A Large Ion Collider Experiment at CERN) so as to cater to the high luminosity environment expected at the Large Hadron Collider (LHC) facility in future. This device will rely on the intrinsic ion back flow (IBF) suppression of Micro-Pattern Gas Detectors (MPGD) based technology in particular the Gas Electron Multiplier (GEM). GEM is to minimise the space charge effect in the main drift volume and thus will not require the standard gating grid and the resulting intrinsic dead time. It will thus be poss…
In this paper lossless and a quasi lossless algorithms for the online compression of the data generated by the Time Projection Chamber (TPC) detector of the ALICE experiment at CERN are described. The first algorithm is based on a lossless source code modelling technique, i.e. the original TPC signal information can be reconstructed without errors at the decompression stage. The source model exploits the temporal correlation that is present in the TPC data to reduce the entropy of the source. The second algorithm is based on a lossy source code modelling technique. In order to evaluate the con…
In LHC Run 3, ALICE will increase the data taking rate significantly to 50\,kHz continuous read out of minimum bias Pb-Pb events. This challenges the online and offline computing infrastructure, requiring to process 50 times as many events per second as in Run 2, and increasing the data compression ratio from 5 to 20. Such high data compression is impossible by lossless ZIP-like algorithms, but it must use results from online reconstruction, which in turn requires online calibration. These important online processing steps are the most computing-intense ones, and will use GPUs as hardware acce…
The ALICE Collaboration will undertake a major upgrade of the detector apparatus during the second LHC Long Shutdown LS2 (2019-2020) in view of the Runs 3 and 4 (2021-2029). The objective of the upgrade is two-fold: i) an improvement of the tracking precision and efficiency, in particular in the low-momentum range; ii) an improvement of the readout capabilities of the experiment, in order to fully exploit the luminosity for heavy ions envisaged after LS2. The first goal will be achieved by replacing the Inner Tracking System with a new tracker, composed of seven layers of silicon pixel detecto…
We study the electron/pion identification performance of the ALICE Transition Radiation Detector (TRD) prototypes using a neural network (NN) algorithm. Measurements were carried out for particle momenta from 2 to 6 GeV/c. An improvement in pion rejection by about a factor of 3 is obtained with NN compared to standard likelihood methods.
For the International Large Detector (ILD) at the planned International Linear Collider (ILC) a Time Projection Chamber (TPC) is foreseen as the main tracking detector. To achieve the required point resolution, Micro Pattern Gaseous Detectors (MPGD) will be used in the amplification stage. A readout module using a stack of three Gas Electron Multipliers (GEM) for gas amplification was developed at DESY. In a test campaign at the DESY II Test Beam Facility the performance of three of these modules was investigated. In this contribution results were presented on the particle identification capab…
We present the electron/pion identification performance measured with prototypes for ALICE TRD. Measured spectra of energy deposit of pions and electrons as well as their average values are presented and compared to calculations. Various radiators are investigated over the momentum range of 1 to 6 GeV/c. The time signature of TR is exploited in a bidimensional likelihood mothod.
We derive a method to improve particle identification (PID) at high transverse momentum ($p_T$) using the relativistic rise of the ionization energy loss ($rdE/dx$) when charged particles traverse the Time Projection Chamber (TPC) at STAR. Electrons triggered and identified by the Barrel Electro-Magnetic Calorimeter (BEMC), pure protons and pions from $Λ\to p+π^{-}$ ($\barΛ\to \bar{p}+π^{+}$), and $K^{0}_{S}\toπ^{+}+π^{-}$ decays are used to obtain the $dE/dx$ value and its width at given $βγ=p/m$. We found that the deviation of the $dE/dx$ from the Bichsel function can be up to $0.4σ$ ($\sim3…
A large Time Projection Chamber is the main device for tracking and charged-particle identification in the ALICE experiment at the CERN LHC. After the second long shutdown in 2019/20, the LHC will deliver Pb beams colliding at an interaction rate of about 50 kHz, which is about a factor of 50 above the present readout rate of the TPC. This will result in a significant improvement on the sensitivity to rare probes that are considered key observables to characterize the QCD matter created in such collisions. In order to make full use of this luminosity, the currently used gated Multi-Wire Propor…
The upgrade of the ALICE TPC will allow the experiment to cope with the high interaction rates foreseen for the forthcoming Run 3 and Run 4 at the CERN LHC. In this article, we describe the design of new readout chambers and front-end electronics, which are driven by the goals of the experiment. Gas Electron Multiplier (GEM) detectors arranged in stacks containing four GEMs each, and continuous readout electronics based on the SAMPA chip, an ALICE development, are replacing the previous elements. The construction of these new elements, together with their associated quality control procedures,…
We have constructed a liquid Argon TPC detector with fiducial mass of 150 kg as a part of the R&D program of the next generation neutrino and nucleon decay detector. This paper describes a study of particle identification performance of the detector using well-defined charged particles (pions, kaons, and protons) with momentum of ~800 MeV/$c$ obtained at J-PARC K1.1BR beamline.
In the HARP experiment the large-angle spectrometer is using a cylindrical TPC as main tracking and particle identification detector. The momentum scale of reconstructed tracks in the TPC is the most important systematic error for the majority of kinematic bins used for the HARP measurements of the double-differential production cross-section of charged pions in proton interactions on nuclear targets at large angle. The HARP TPC operated with a number of hardware shortfalls and operational mistakes. Thus it was important to control and characterize its momentum calibration. While it was not po…
The kaon identification is crucial for the flavor physics, and also benefits the flavor and charge reconstruction of the jets. We explore the particle identification capability for tracks with momenta ranging from 2-20 GeV/c using the $dE/dx$ measurements in the Time Projection Chamber at the future Circular Electron-Positron Collider. Based on Monte Carlo simulation, we anticipate that an average $3.2~σ$ ($2.6~σ$) $K/π$ separation can be achieved based on $dE/dx$ information for an optimistic (conservative) extrapolation of the simulated performance to the final system. Time-of-flight (TOF) i…
A prototype detector is being developed which combines the functions of a Time Projection Chamber for charged particle tracking and a Cherenkov detector for particle identification. The TPC consists of a 10x10x10 cm3 drift volume where the charge is drifted to a 10x10 cm2 triple GEM detector. The charge is measured on a readout plane consisting of 2x10 mm2 chevron pads which provide a spatial resolution ~ 100 microns per point in the chevron direction along with dE/dx information. The Cherenkov portion of the detector consists of a second 10x10 cm2 triple GEM with a photosensitive CsI photocat…
This paper presents the Forward Time Projection Chamber (FTPC) system of the NA61/SHINE experiment at the CERN SPS accelerator. This TPC system applies a novel tandem-TPC design to reduce the background originating from particle tracks not synchronous with the event trigger. The FTPC system is composed of three chambers with alternating drift field directions. The chambers were installed directly along the beamline region of the NA61/SHINE detector in a medium- to high-intensity (10-100 kHz) hadron or ion beam. The tandem TPC system has proved to be capable of rejecting out-of-time background …
The Transition Radiation Detector (TRD) provides particle identification in the ALICE central barrel. In particular, it allows electron identification via the measurement of transition radiation for $\rm p >$ 1 GeV/$c$, where pions can no longer be rejected sufficiently via specific energy loss in the ALICE Time Projection Chamber. The ALICE TRD is uniquely designed to record the time evolution of the signal, which allows even better electron/pion separation. In addition, the electron identification capability of the TRD can be used on-line to trigger at level 1. The particle identification an…
Precision timing has alway been a prominent topic in the instrumentation for high-energy physics experiments. In this document I discuss what the perspectives are for the use of silicon sensors for a time-of-flight detector in a next-generation heavy-ion experiment at the LHC. A brief overview of the experiment and a preliminary assessment of the expected particle-identification performance is also presented.
The search for a novel technology able to detect and reconstruct nuclear recoil events in the keV energy range has become more and more important as long as vast regions of high mass WIMP-like Dark Matter candidate have been excluded. Gaseous Time Projection Chambers (TPC) with optical readout are very promising candidate combining the complete event information provided by the TPC technique to the high sensitivity and granularity of last generation scientific light sensors. A TPC with an amplification at the anode obtained with Gas Electron Multipliers (GEM) was tested at the Laboratori Nazio…
This document contains the pre-design of the beam diagnostics components Tracking Detectors for the Super-FRS. A GEM-TPC detector has been suggested as suitable tracking detector for the ion/fragment beams produced at the in-flight separator Super-FRS under construction at the FAIR facility. The detector concept combines two widely used approaches in gas filled detectors, the Time Projection Chamber (TPC) and the Gas Electron Multiplication (GEM). Three detector generations (prototypes) have been tested in 2011, 2012 and 2014 with relativistic ion beams at GSI. Due to the high-resolution achro…
The specific energy loss (dE/dx) resolution is critical for particle identification and separation in TPC. In connection with the R&D for the TPC at the Circular Electron Positron Collider (CEPC), we find the laser ionisation obeys the Gaussian distribution theoretically and experimentally. Based on this, we develop a novel method using a 266 nm UV laser to measure the dE/dx resolution. Comparing to the traditional methods with particle beams or cosmic rays, the novel method with 266 nm UV laser is more convenient and flexible. We verify the method's feasibility with a TPC prototype and extrap…
Particle identification is an important feature of the ALICE detector at the LHC. In particular, for particle identification via the time-of-flight technique, the precise determination of the event collision time represents an important ingredient of the quality of the measurement. In this paper, the different methods used for such a measurement in ALICE by means of the T0 and the TOF detectors are reviewed. Efficiencies, resolution and the improvement of the particle identification separation power of the methods used are presented for the different LHC colliding systems (pp , p-Pb and Pb-Pb)…
The Time Projection Chamber (TPC) can identify particle species using the energy loss (dE/dx) measured by the readout pad rows. The dE/dx resolution for the ILD (International Large Detector) -TPC for the International Linear Collider experiment is expected to have high resolution for clear identification. The dE/dx resolution of our prototype TPC with gating device (gating GEM) to suppress ions feedback was measured using the electron test beam in a magnet field at the facility in DESY. The dE/dx resolution for ILD-TPC was estimated using this test beam data. The signal charge was measured as…
AXEL is a high-pressure xenon gas time projection chamber for neutrinoless double-beta decay (0n2b) search. The AXEL has a unique readout system called ELCC which has a cellular structure and photosensors to detect electroluminescence light produced by ionization electrons. We demonstrated the performance of the ELCC with a small prototype detector (AXEL-HP10L). The obtained energy resolution corresponds to 0.82 -- 1.74% (FWHM) at the 0n2b Q-value. We are constructing a new prototype (AXEL-HP180L) in order to study the energy resolution at the Q-value of 0n2b with a new design of ELCC with uni…
The Inner Tracking System is the ALICE detector closest to the beam axis. It is composed of six layers of silicon detectors: two innermost layers of Silicon Pixel Detectors (SPD), two intermediate layers of Silicon Drift Detectors (SDD) and two outermost layers of Silicon Strip Detectors (SSD). The ITS can be used as a standalone tracker in order to recover tracks that are not reconstructed by the Time Projection Chamber (TPC) and to reconstruct low momentum particles with $p_{t}$ down to 100 MeV/c. Particle identification in the ITS is performed by measuring the energy loss signal in the SDD …
