We investigate the source of large variations in the observed detection effiiencies of superconducting nanowire single-photon detectors between many nominally identical devices. Through both electrical and optical measurements, we infer that these variations arise from "constrictions:" highly localized regions of the nanowires where the effective cross-sectional area for superconducting current is reduced. These constrictions limit the DC bias current density to well below its critical value over the remainder of the wire, and thus prevent the detection efficiency from reaching the high values that occur in these devices only when they are biased near the critical current density.
We investigated the timing jitter of superconducting nanowire avalanche photodetectors (SNAPs, also referred to as cascade switching superconducting single photon detectors) based on 30-nm-wide nanowires. At bias currents (IB) near the switching current, SNAPs showed sub 35 ps FWHM Gaussian jitter similar to standard 100 nm wide superconducting nanowire single-photon detectors. At lower values of IB, the instrument response function (IRF) of the detectors became wider, more asymmetric, and shifted to longer time delays. We could reproduce the experimentally observed IRF time-shift in simulatio…
Superconducting nanowire single photon detectors are typically biased using a constant current source and shunted in a conductance which is over an order of magnitude larger than the peak normal domain conductance of the detector. While this design choice is required to ensure quenching of the normal domain, the use of a small load resistor limits the pulse amplitude, rising-edge slew rate, and recovery time of the detector. Here, we explore the possibility of actively quenching the normal domain, thereby removing the need to shunt the detector in a small resistance. We first consider the theo…
We present a 1024-element imaging array of superconducting nanowire single photon detectors (SNSPDs) using a 32x32 row-column multiplexing architecture. Large arrays are desirable for applications such as imaging, spectroscopy, or particle detection.
We present a linearly arrayed, 16-element, superconducting nanowire single-photon detector with 83.4$\%$ system detection efficiency at 1550 nm and a mean per-element dead-time of 9.6-ns, enabling counting at 1 giga-count per second with $>50\%$ System Detection Efficiency. This device was designed and fabricated in an existing scalable commercial process.
Here we propose a new design paradigm for a superconducting nanowire single photon detector that uses a multi-layer architecture that places the electric leads beneath the nanowires. This allows for a very large number of detector elements, which we will call pixels in analogy to a conventional CCD camera, to be placed in close proximity. This leads to significantly better photon number resolution than current single and multi-nanowire meanders, while maintaining similar detection areas. We discuss the reset time of the pixels and how the design can be modified to avoid the latching failure se…
We describe a micromachining process to allow the coupling of an array of single-mode telecommunication fibers to individual superconducting nanowire single photon detectors (SNSPDs). As proof of principle, we show the integration of four detectors on the same silicon chip, including two standard single-section nanowire detectors and two superconducting nanowire avalanche photodetectors (SNAPs) with modified series structure without external inductor, and their performances are compared. The SNAP shows saturated system detection efficiency of 16% while the dark count rate is less than 20 Hz, w…
Properties of superconducting nanowires set the performance level for Superconducting Nanowire Single Photon Detectors (SNSPD). Reset time in commonly employed large area SNSPDs,5-10ns,is known to be limited by the nanowires kinetic inductance.On the other hand, reduction of the kinetic inductance in small area (waveguide integrated) SNSPDs prevents biasing them close to the critical current due to latching into a permanent resistive state.In order to reduce the reset time in SNSPDs, superconducting nanowires with both low kinetic inductance and fast electron energy relaxation are required. In…
We demonstrate a 16-pixel array of radio-frequency superconducting nanowire single-photon detectors with an integrated and scalable frequency-division multiplexing architecture, reducing the required bias and readout lines to a single microwave feed line. The electrical behavior of the photon-sensitive nanowires, embedded in a resonant circuit, as well as the optical performance and timing jitter of the single detectors is discussed. Besides the single pixel measurements we also demonstrate the operation of the 16-pixel array with a temporal, spatial and photon-number resolution.
We investigate the recovery of superconducting NbN-nanowire photon counters after detection of an optical pulse at a wavelength of 1550 nm, and present a model that quantitatively accounts for our observations. The reset time is found to be limited by the large kinetic inductance of these nanowires, which forces a tradeoff between counting rate and either detection efficiency or active area. Devices of usable size and high detection efficiency are found to have reset times orders of magnitude longer than their intrinsic photoresponse time.
We demonstrate a 64-pixel free-space-coupled array of superconducting nanowire single photon detectors optimized for high detection efficiency in the near-infrared range. An integrated, readily scalable, multiplexed readout scheme is employed to reduce the number of readout lines to 16. The cryogenic, optical, and electronic packaging to read out the array, as well as characterization measurements are discussed.
Superconducting nanowire avalanche single-photon detectors (SNAPs) with n parallel nanowires are advantageous over single-nanowire detectors because their output signal amplitude scales linearly with n. However, the SNAP architecture has not been viably demonstrated for n > 4. To increase n for larger signal amplification, we designed a multi-stage, successive-avalanche architecture which used nanowires, connected via choke inductors in a binary-tree layout. We demonstrated an avalanche detector with n = 8 parallel nanowires and achieved eight-fold signal amplification, with a timing jitter of…
We demonstrate high-performance nanowire superconducting single photon detectors (SSPDs) on ultrathin NbN films grown at a temperature compatible with monolithic integration. NbN films ranging from 150nm to 3nm in thickness were deposited by dc magnetron sputtering on MgO substrates at 400C. The superconducting properties of NbN films were optimized studying the effects of deposition parameters on film properties. SSPDs were fabricated on high quality NbN films of different thickness (7 to 3nm) deposited under optimal conditions. Electrical and optical characterizations were performed on the S…
We investigate the performance of superconducting nanowire photon detectors fabricated from ultra-thin Nb. A direct comparison is made between these detectors and similar nanowire detectors fabricated from NbN. We find that Nb detectors are significantly more susceptible than NbN to thermal instability (latching) at high bias. We show that the devices can be stabilized by reducing the input resistance of the readout. Nb detectors optimized in this way are shown to have approximately 2/3 the reset time of similar large-active-area NbN detectors of the same geometry, with approximately 6% detect…
Superconducting nanowires are widely used as sensitive single photon detectors with wide spectral coverage and high timing resolution. We describe a demonstration of an array of DC biased superconducting nanowire single photon detectors read out with a microwave multiplexing circuit. In this design, each individual nanowire is part of a resonant LC circuit where the inductance is dominated by the kinetic inductance of the nanowire. The circuit also contains two parallel plate capacitors, one of them is in parallel with the inductor and the other is coupled to a microwave transmission line whic…
We demonstrate waveguide-integrated superconducting nanowire single-photon detectors on thin-film lithium niobate (LN). Using a 250 um-long NbN superconducting nanowire lithographically defined on top of a 125 um-long LN nanowaveguide, on-chip detection efficiency of 46% is realized with simultaneous high performance in dark count rate and timing jitter. As LN possesses high second-order nonlinear \c{hi}(2) and electro-optic properties, an efficient single-photon detector on thin-film LN opens up the possibility to construct small scale fully-integrated quantum photonic chip which includes sin…
We present the experimental demonstration of a superconducting photon number resolving detector. It is based on the series connection of N superconducting nanowires, each connected in parallel to an integrated resistor. The device provides a single voltage readout, proportional to the number of photons absorbed in distinct nanowires. Clearly separated output levels corresponding to the detection of n=1-4 photons are observed in a 4-element detector fabricated from an NbN film on GaAs substrate, with a single-photon system quantum efficiency of 2.6% at the wavelength of 1300nm. The series-nanow…
We demonstrate the fabrication of micron-wide tungsten silicide superconducting nanowire single-photon detectors on a silicon substrate using laser lithography. We show saturated internal detection efficiencies with wire widths from 0.59$μ$m to 1.43$μ$m under illumination at 1550nm. We demonstrate both straight wires, as well as meandered structures. Single-photon sensitivity is shown in devices up to 4mm in length. Laser-lithographically written devices allow for fast and easy structuring of large areas while maintaining a saturated internal efficiency for wire width around 1$μ$m.
We present a time-over-threshold readout technique to count the number of activated pixels from an array of superconducting nanowire single photon detectors (SNSPDs). This technique maintains the intrinsic timing jitter of the individual pixels, places no additional heatload on the cryostat, and retains the intrinsic count rate of the time-tagger. We demonstrate proof-of-principle operation with respect to a four-pixel device. Furthermore, we show that, given some permissible error threshold, the number of pixels that can be reliably read out scales linearly with the intrinsic signal-to-noise …
We demonstrate and verify quantum detector tomography of a superconducting nanowire single-photon detector (SNSPD) in a multiplexing scheme which permits measurement of up to 71000 photons per input pulse. We reconstruct the positive operator valued measure (POVM) of this device in the low photon-number regime, and use the extracted parameters to show the POVMs spanning the whole dynamic range of the device. We verify this by finding the mean photon number of a bright state. Our work shows that a reliable quantum description of large-scale SNSPD devices is possible, and should be applicable to…
We present an active anti-latching system for superconducting nanowire single-photon detectors. We experimentally test it against a bright-light attack, previously used to compromise security of quantum key distribution. Although our system detects continuous blinding, the detector is shown to be partially blindable and controllable by specially tailored sequences of bright pulses. Improvements to the countermeasure are suggested.
High-quality ultra-thin films of niobium nitride (NbN) are developed by plasma-enhanced atomic layer deposition (PEALD) technique. Superconducting nanowire single-photon detectors (SNSPDs) patterned from this material exhibit high switching currents and saturated internal efficiencies over a broad bias range at 1550 nm telecommunication wavelength. Statistical analyses on hundreds of fabricated devices show near-unity throughput yield due to exceptional homogeneity of the films. The ALD-NbN material represents an ideal superconducting material for fabricating large single-photon detector array…
We demonstrate a scalable readout scheme for an infrared single-photon pulse-position camera consisting of WSi superconducting nanowire single-photon detectors (SNSPDs). For an N x N array, only 2 x N wires are required to obtain the position of a detection event. As a proof-of-principle, we show results from a 2 x 2 array.
We present a novel design of a superconducting nanowire single photon detector (SNSPD) fabricated on a core of a single mode optical fiber. The proposed design allows high overlap between the fiber light mode and the detector, and consequently, our fabricated devices can remain small in dimension and maintain speed of operation, without scarifying the detection efficiency. The on-fiber fabrication method is detailed, together with experimental results. The proposed method can be exploited in the future for the fabrication of other fiber coupled devices.
We investigated the reset time of superconducting nanowire avalanche photodetectors (SNAPs) based on 30 nm wide nanowires. We studied the dependence of the reset time of SNAPs on the device inductance and discovered that SNAPs can provide a speed-up relative to SNSPDs with the same area, but with some limitations: (1) reducing the series inductance of SNAPs (necessary for the avalanche formation) could result in the detectors operating in an unstable regime; (2) a trade-off exists between maximizing the bias current margin and minimizing the reset time of SNAPs; and (3) reducing the reset time…
We present a stable and high-performance fiber-coupled NbTiN superconducting nanowire avalanche photon detector (SNAP). We demonstrate afterpulse-free operation in serially connected two SNAPs (SC-2SNAP), even in the absence of a choke inductor, achieving a 7.7 times faster response speed than standard SSPDs. The SC-2SNAP device showed a system detection efficiency (SDE) of 81.0% with wide bias current margin, a dark count rate of 6.8 counts/s, and full width at half maximum timing jitter of 68 ps, operating at 2.3 K.
The superconducting nanowire single-photon detector (SNSPD) is a quantum-limit superconducting optical detector based on the Cooper-pair breaking effect by a single photon, which exhibits a higher detection efficiency, lower dark count rate, higher counting rate, and lower timing jitter when compared with those exhibited by its counterparts. SNSPDs have been extensively applied in quantum information processing, including quantum key distribution and optical quantum computation. In this review, we present the requirements of single-photon detectors from quantum information, as well as the prin…
Recent progress in the development of superconducting nanowire single-photon detectors (SNSPDs) made of amorphous material has delivered excellent performances, and has had a great impact on a range of research fields. Despite showing the highest system detection efficiency (SDE) ever reported with SNSPDs, amorphous materials typically lead to lower critical currents, which impacts on their jitter performance. Combining a very low jitter and a high SDE remains a challenge. Here, we report on highly efficient superconducting nanowire single-photon detectors based on amorphous MoSi, combining sy…
We present high performance fiber-coupled niobium titanium nitride superconducting nanowire single photon detectors fabricated on thermally oxidized silicon substrates. The best device showed a system detection efficiency (DE) of 74%, dark count rate of 100 c/s, and full width at half maximum timing jitter of 68 ps under a bias current of 18.0 uA with a practical Gifford-McMahon cryocooler system. We also introduced six detectors into the cryocooler and confirmed that the system DE of all detectors was higher than 67% at the dark count rate of 100 c/s.
Universal fault-tolerant quantum computers, which promise to revolutionize computing, are currently limited by excessive noise in their constituent superconducting qubits. Determining the dominant sources of this excess noise will lead to a clearer understanding of how to mitigate it in future superconducting systems. Superconducting Nanowire Single-Photon Detectors (SNSPDs) are devices that do not appear to suffer from such effects and have extremely low dark-count backgrounds. We propose to use SNSPDs as low-background laboratories to study noise accumulation processes in superconducting sys…
We propose an optimized design for nanowire superconducting single photon detectors, using the recently discovered position dependent detection efficiency in these devices. This knowledge allows an optimized the design of meandering wire NbN detectors by altering the field distribution across the wire. In order to calculate the response of the detectors with different geometries, we use a monotonic local detection efficiency from a nanowire and optical absorption distribution via finite-different-time-domain simulations. The calculations predict a trade-off between average absorption and the e…
We demonstrate the integration of amorphous tungsten silicide superconducting nanowire single-photon detectors on titanium in-diffused lithium niobate waveguides. We show proof-of-principle detection of evanescently-coupled photons of 1550nm wavelength using bidirectional waveguide coupling for two orthogonal polarization directions. We investigate the internal detection efficiency as well as detector absorption using coupling-independent characterization measurements. Furthermore, we describe strategies to improve the yield and efficiency of these devices.
State-of-the-art Superconducting Nanowire Single Photon Detectors based on low-Tc materials reach 100% quantum efficiency. However, the response time is limited to >1-10 ns. Recently, it has been shown that due to a much lower kinetic inductance, a 100 ps response rate can be achieved in 120 $μ$m-long $MgB_{2}$ nanowires. In this work, we demonstrate experimentally that such $MgB_{2}$ nanowires function as single-photon detectors for both visible ($λ$= 630 nm) and infrared ($λ$= 1550 nm) photons when biased close to the critical current, with a dark count rate of <10 cps. $MgB_{2}$ photodetect…
Superconducting nanowire single photon detectors are capable of single-photon detection across a large spectral range, with near unity detection efficiency, picosecond timing jitter, and sub-10 $μ$m position resolution at rates as high as 10$^{9}$ counts/s. In an effort to bring this technology into nuclear physics experiments, we fabricate Niobium Nitride nanowire detectors using ion beam assisted sputtering and test their performance in strong magnetic fields. We demonstrate that these devices are capable of detection of 400 nm wavelength photons with saturated internal quantum efficiency at…
