We demonstrate and verify quantum detector tomography of a superconducting nanowire single-photon detector (SNSPD) in a multiplexing scheme which permits measurement of up to 71000 photons per input pulse. We reconstruct the positive operator valued measure (POVM) of this device in the low photon-number regime, and use the extracted parameters to show the POVMs spanning the whole dynamic range of the device. We verify this by finding the mean photon number of a bright state. Our work shows that a reliable quantum description of large-scale SNSPD devices is possible, and should be applicable to other multiplexing configurations.
We demonstrate quantum detector tomography of a commercial 2x2 array of superconducting nanowire single photon detectors. We show that detector-specific figures of merit including efficiency, dark-count and cross-talk probabilities can be directly extracted, without recourse to the underlying detector physics. These figures of merit are directly identified from just four elements of the reconstructed positive operator valued measure (POVM) of the device. We show that the values for efficiency and dark-count probability extracted by detector tomography show excellent agreement with independent …
We present a linearly arrayed, 16-element, superconducting nanowire single-photon detector with 83.4$\%$ system detection efficiency at 1550 nm and a mean per-element dead-time of 9.6-ns, enabling counting at 1 giga-count per second with $>50\%$ System Detection Efficiency. This device was designed and fabricated in an existing scalable commercial process.
We demonstrate a 64-pixel free-space-coupled array of superconducting nanowire single photon detectors optimized for high detection efficiency in the near-infrared range. An integrated, readily scalable, multiplexed readout scheme is employed to reduce the number of readout lines to 16. The cryogenic, optical, and electronic packaging to read out the array, as well as characterization measurements are discussed.
We demonstrate the fabrication of micron-wide tungsten silicide superconducting nanowire single-photon detectors on a silicon substrate using laser lithography. We show saturated internal detection efficiencies with wire widths from 0.59$μ$m to 1.43$μ$m under illumination at 1550nm. We demonstrate both straight wires, as well as meandered structures. Single-photon sensitivity is shown in devices up to 4mm in length. Laser-lithographically written devices allow for fast and easy structuring of large areas while maintaining a saturated internal efficiency for wire width around 1$μ$m.
We present a time-over-threshold readout technique to count the number of activated pixels from an array of superconducting nanowire single photon detectors (SNSPDs). This technique maintains the intrinsic timing jitter of the individual pixels, places no additional heatload on the cryostat, and retains the intrinsic count rate of the time-tagger. We demonstrate proof-of-principle operation with respect to a four-pixel device. Furthermore, we show that, given some permissible error threshold, the number of pixels that can be reliably read out scales linearly with the intrinsic signal-to-noise …
Here we propose a new design paradigm for a superconducting nanowire single photon detector that uses a multi-layer architecture that places the electric leads beneath the nanowires. This allows for a very large number of detector elements, which we will call pixels in analogy to a conventional CCD camera, to be placed in close proximity. This leads to significantly better photon number resolution than current single and multi-nanowire meanders, while maintaining similar detection areas. We discuss the reset time of the pixels and how the design can be modified to avoid the latching failure se…
Superconducting nanowire avalanche single-photon detectors (SNAPs) with n parallel nanowires are advantageous over single-nanowire detectors because their output signal amplitude scales linearly with n. However, the SNAP architecture has not been viably demonstrated for n > 4. To increase n for larger signal amplification, we designed a multi-stage, successive-avalanche architecture which used nanowires, connected via choke inductors in a binary-tree layout. We demonstrated an avalanche detector with n = 8 parallel nanowires and achieved eight-fold signal amplification, with a timing jitter of…
We present the experimental demonstration of a superconducting photon number resolving detector. It is based on the series connection of N superconducting nanowires, each connected in parallel to an integrated resistor. The device provides a single voltage readout, proportional to the number of photons absorbed in distinct nanowires. Clearly separated output levels corresponding to the detection of n=1-4 photons are observed in a 4-element detector fabricated from an NbN film on GaAs substrate, with a single-photon system quantum efficiency of 2.6% at the wavelength of 1300nm. The series-nanow…
We present an active anti-latching system for superconducting nanowire single-photon detectors. We experimentally test it against a bright-light attack, previously used to compromise security of quantum key distribution. Although our system detects continuous blinding, the detector is shown to be partially blindable and controllable by specially tailored sequences of bright pulses. Improvements to the countermeasure are suggested.
We demonstrate a scalable readout scheme for an infrared single-photon pulse-position camera consisting of WSi superconducting nanowire single-photon detectors (SNSPDs). For an N x N array, only 2 x N wires are required to obtain the position of a detection event. As a proof-of-principle, we show results from a 2 x 2 array.
We investigated the reset time of superconducting nanowire avalanche photodetectors (SNAPs) based on 30 nm wide nanowires. We studied the dependence of the reset time of SNAPs on the device inductance and discovered that SNAPs can provide a speed-up relative to SNSPDs with the same area, but with some limitations: (1) reducing the series inductance of SNAPs (necessary for the avalanche formation) could result in the detectors operating in an unstable regime; (2) a trade-off exists between maximizing the bias current margin and minimizing the reset time of SNAPs; and (3) reducing the reset time…
We present a stable and high-performance fiber-coupled NbTiN superconducting nanowire avalanche photon detector (SNAP). We demonstrate afterpulse-free operation in serially connected two SNAPs (SC-2SNAP), even in the absence of a choke inductor, achieving a 7.7 times faster response speed than standard SSPDs. The SC-2SNAP device showed a system detection efficiency (SDE) of 81.0% with wide bias current margin, a dark count rate of 6.8 counts/s, and full width at half maximum timing jitter of 68 ps, operating at 2.3 K.
The superconducting nanowire single-photon detector (SNSPD) is a quantum-limit superconducting optical detector based on the Cooper-pair breaking effect by a single photon, which exhibits a higher detection efficiency, lower dark count rate, higher counting rate, and lower timing jitter when compared with those exhibited by its counterparts. SNSPDs have been extensively applied in quantum information processing, including quantum key distribution and optical quantum computation. In this review, we present the requirements of single-photon detectors from quantum information, as well as the prin…
Recent progress in the development of superconducting nanowire single-photon detectors (SNSPDs) made of amorphous material has delivered excellent performances, and has had a great impact on a range of research fields. Despite showing the highest system detection efficiency (SDE) ever reported with SNSPDs, amorphous materials typically lead to lower critical currents, which impacts on their jitter performance. Combining a very low jitter and a high SDE remains a challenge. Here, we report on highly efficient superconducting nanowire single-photon detectors based on amorphous MoSi, combining sy…
Universal fault-tolerant quantum computers, which promise to revolutionize computing, are currently limited by excessive noise in their constituent superconducting qubits. Determining the dominant sources of this excess noise will lead to a clearer understanding of how to mitigate it in future superconducting systems. Superconducting Nanowire Single-Photon Detectors (SNSPDs) are devices that do not appear to suffer from such effects and have extremely low dark-count backgrounds. We propose to use SNSPDs as low-background laboratories to study noise accumulation processes in superconducting sys…
We developed an electro thermal model of NbN superconducting nanowire avalanche photodetectors (SNAPs) on sapphire substrates. SNAPs are single photon detectors consisting of the parallel connection of N superconducting nanowires. We extrapolated the physical constants of the model from experimental data and we simulated the time evolution of the device resistance, temperature and current by solving two coupled electrical and thermal differential equations describing the nanowires. The predictions of the model were in good quantitative agreement with the experimental results.
We demonstrate the integration of amorphous tungsten silicide superconducting nanowire single-photon detectors on titanium in-diffused lithium niobate waveguides. We show proof-of-principle detection of evanescently-coupled photons of 1550nm wavelength using bidirectional waveguide coupling for two orthogonal polarization directions. We investigate the internal detection efficiency as well as detector absorption using coupling-independent characterization measurements. Furthermore, we describe strategies to improve the yield and efficiency of these devices.
Multiphoton contributions pose a significant challenge for the realisation of heralded single-photon sources (HSPS) based on nonlinear processes. In this work, we improve the quality of single photons generated in this way by harnessing the photon-number resolving (PNR) capabilities of commercial superconducting nanowire single-photon detectors (SNSPDs). We report a $13 \pm 0.4 \%$ reduction in the intensity correlation function $g^{(2)}(0)$ even with a collection efficiency in the photon source of only $29.6\%$. Our work demonstrates the first application of the PNR capabilities of SNSPDs and…
We report on simulation results that shows optimum photon absorption by superconducting nanowires can happen at a fill-factor that is much less than 100%. We also present experimental results on high performance of our superconducting nanowire single photon detectors realized using NbTiN on oxidized silicon.
We propose an optimized design for nanowire superconducting single photon detectors, using the recently discovered position dependent detection efficiency in these devices. This knowledge allows an optimized the design of meandering wire NbN detectors by altering the field distribution across the wire. In order to calculate the response of the detectors with different geometries, we use a monotonic local detection efficiency from a nanowire and optical absorption distribution via finite-different-time-domain simulations. The calculations predict a trade-off between average absorption and the e…
We experimentally demonstrate that a superconducting nanowire single-photon detector is deterministically controllable by bright illumination. We found that bright light can temporarily make a large fraction of the nanowire length normally-conductive, can extend deadtime after a normal photon detection, and can cause a hotspot formation during the deadtime with a highly nonlinear sensitivity. In result, although based on different physics, the superconducting detector turns out to be controllable by virtually the same techniques as avalanche photodiode detectors. As demonstrated earlier, when …
Superconducting nanowire single photon detectors (SNSPDs) are fabricated directly on diamond substrates and their optical and electrical properties are characterized. Dark count performance and photon count rates are measured at varying temperatures for 1310nm and 632nm photons. The procedure to prepare diamond substrate surfaces suitable for the deposition and patterning of thin film superconducting layers is reported. Using this approach, diamond substrates with less than 300pm RMS surface roughness are obtained.
We present low-temperature measurements of low-loss superconducting nanowire-embedded resonators in the low-power limit relevant for quantum circuits. The superconducting resonators are embedded with superconducting nanowires with widths down to 20nm using a neon focused ion beam. In the low-power limit, we demonstrate an internal quality factor up to 3.9x10^5 at 300mK [implying a two-level-system-limited quality factor up to 2x10^5 at 10 mK], not only significantly higher than in similar devices but also matching the state of the art of conventional Josephson-junction-embedded resonators. We …
Superconducting nanowire single-photon detectors (SNSPDs) perform single-photon counting with exceptional sensitivity and time resolution at near-infrared wavelengths. State-of-the-art SNSPDs, based on 100 nm-wide, 4 to 5 nm thick NbN nanowires, are vulnerable to constrictions, which significantly limit their yield. Also, their sensitivity becomes negligible beyond 2 μm wavelength, which makes them unsuitable for mid-infrared applications. SNSPDs based on few-tens-of-nanometer-wide nanowires are expected to efficiently detect mid-infrared photons and to operate at low bias currents, so constri…
We report the fabrication of a superconducting nanowire single-photon detector (SSPD or SNSPD) with an ultralow dark count rate. By introducing optical band-pass filters at the input of the SSPD and cooling the filters at 3 K, the dark count rate is reduced to less than 1/100 at low bias. An SSPD with 0.1 cps dark count rate and 5.6% system detection efficiency at 1550 nm wavelength is obtained. We show that a quantum key distribution (QKD) over 300 km of fiber is possible based on a numerical calculation assuming a differential phase shift QKD protocol implemented with our SSPDs.
Single-photon detectors based on superconducting nanowires (SSPDs or SNSPDs) have rapidly emerged as a highly promising photon-counting technology for infrared wavelengths. These devices offer high efficiency, low dark counts and excellent timing resolution. In this review, we consider the basic SNSPD operating principle and models of device behaviour. We give an overview of the evolution of SNSPD device design and the improvements in performance which have been achieved. We also evaluate device limitations and noise mechanisms. We survey practical refrigeration technologies and optical coupli…
We demonstrate superconducting nanowire single photon detectors with 76 +/- 4 % system detection efficiency at a wavelength of 315 nm and an operating temperature of 3.2 K, with a background count rate below 1 count per second at saturated detection efficiency. We propose integrating these detectors into planar surface electrode radio-frequency Paul traps for use in trapped ion quantum information processing. We operate detectors integrated into test ion trap structures at 3.8 K both with and without typical radio-frequency trapping electric fields. The trapping fields reduce system detection …
We demonstrate niobium titanium nitride superconducting nanowires patterned on stoichiometric silicon nitride waveguides for detecting visible and infrared photons. The use of silicon nitride on insulator on silicon substrates allows us to simultaneously realize photonic circuits for visible and infrared light and integrate them with nanowire detectors directly on-chip. By implementing a traveling wave detector geometry in this material platform, we achieve efficient single photon detection for both wavelength regimes. Our detectors are an ideal match for integrated quantum optics as they prov…
The origin of the decoherence in superconducting nanowire single-photon detectors, the so-called dark count, was investigated. We measured the direct-current characteristics and bias-current dependencies of the dark count rate in a wide range of temperatures from 0.5 K to 4 K, and analyzed the results by theoretical models of thermal fluctuations of vortices. Our results indicate that the current-assisted unbinding of vortex-antivortex pairs is the dominant origin of the dark count.
Superconducting nanowires, a mature technology originally developed for quantum sensing, can be used as a target and sensor with which to search for dark matter interactions with electrons. Here we report on a 180-hour measurement of a tungsten silicide superconducting nanowire device with a mass of 4.3 nanograms. We use this to place new constraints on dark matter--electron interactions, including the strongest terrestrial constraints to date on sub-MeV (sub-eV) dark matter that interacts with electrons via scattering (absorption) processes.
We measure the maximal distance at which two absorbed photons can jointly trigger a detection event in NbN nanowire superconducting single photon detector (SSPD) microbridges by comparing the one-photon and two-photon efficiency of bridges of different overall lengths, from 0 to 400 nm. We find a length of $23 \pm 2$ nm. This value is in good agreement with to size of the quasiparticle cloud at the time of the detection event.
We investigate the circuit quantum electrodynamics of anharmonic superconducting nanowire oscillators. The sample circuit consists of a capacitively shunted nanowire with a width of about 20 nm and a varying length up to 350 nm, capacitively coupled to an on-chip resonator. By applying microwave pulses we observe Rabi oscillations, measure coherence times and the anharmonicity of the circuit. Despite the very compact design, simple top-down fabrication and high degree of disorder in the oxidized (granular) aluminum material used, we observe lifetimes in the microsecond range.
We use quantum detector tomography to investigate the detection mechanism in WSi nanowire superconducting single photon detectors (SSPDs). To this purpose, we fabricated a 250nm wide and 250nm long WSi nanowire and measured its response to impinging photons with wavelengths ranging from $λ$ = 900 nm to $λ$ = 1650 nm. Tomographic measurements show that the detector response depends on the total excitation energy only. Moreover, for energies Et > 0.8eV the current energy relation is linear, similar to what was observed in NbN nanowires, whereas the current-energy relation deviates from linear be…
We present the performances of a superconducting nanowire single-photon detector (SNSPD) in an ultralow-temperature region from 16 mK to 4 K. The system detection efficiency of the SNSPD showed saturation in the bias-current and temperature dependences, and reached the considerably high value of 15% for 100 Hz dark count rate below 1.4 K at a wavelength of 1550 nm even without an optical cavity structure. We found that the dark count exists even at 16 mK and black body radiation becomes its dominant origin in the low temperatures for fiber-coupled devices.
We developed superconducting nanowire single-photon detectors with an optical cavity (OC-SNSPDs) for multichannel systems. For efficient coupling, the devices were installed in compact fiber-coupled packages after their substrate thickness was reduced from 400 to 45 $μ$m. The measured detection efficiency (DE) measurement at different substrate thicknesses and the estimation of optical coupling efficiency indicated that ~98% of the input light beam could be radiated on a 15x15 $μm^2$ nanowire area from behind the substrate. The DEs of a NbN OC-SNSPD system were observed to be 9.5% and 25% at 1…
We perform quantum state reconstruction of coherent and thermal states with a detector which has an enhanced multiphoton response. The detector is based on superconducting nanowires, where the bias current sets the dependence of the click probability on the photon number; this bias current is used as tuning parameter in the state reconstruction. The nonlinear response makes our nanowire-based detector superior to the linear detectors that are conventionally used for quantum state reconstruction.
We show a hard induced superconducting gap in a Ge-Si nanowire Josephson transistor up to in-plane magnetic fields of $250$ mT, an important step towards creating and detecting Majorana zero modes in this system. A hard induced gap requires a highly homogeneous tunneling heterointerface between the superconducting contacts and the semiconducting nanowire. This is realized by annealing devices at $180$ $^\circ$C during which aluminium inter-diffuses and replaces the germanium in a section of the nanowire. Next to Al, we find a superconductor with lower critical temperature ($T_\mathrm{C}=0.9$ K…
Integrated arrays of Superconducting Nanowire Single Photon Detectors (SNSPDs) have shown capabilities such as Photon Number Resolution, single photon imaging and coincidences detection, and can be effectively used also in other different applications related to quantum optics. The growing complexity of such applications requires the use of multiplexing schemes for the simultaneous readout of different detectors. A simple multiplexing scheme can be realized by arranging a series of SNSPDs elements, shunted by appropriate resistances. The goal of this work is to investigate and optimize this sc…
We develop single-photon detectors comprising single-mode fiber-coupled superconducting nanowires, with high system detection efficiencies at a wavelength of 940 nm. The detector comprises a 6.5-nm-thick, 110-nm-wide NbN nanowire meander fabricated onto a Si substrate with a distributed Bragg reflector for enhancing the optical absorptance. We demonstrate that, via the design of a low filling factor (1/3) and active area (Φ = 10 μm), the system reaches a detection efficiency of ~60% with a dark count rate of 10 Hz, a recovery time <12 ns, and a timing jitter of ~50 ps.
Superconducting nanowire single photon detectors (SNSPDs) have advanced various frontier scientific and technological fields such as quantum key distribution and deep space communications. However, limited by available cooling technology, all past experimental demonstrations have had ground-based applications. In this work we demonstrate a SNSPD system using a hybrid cryocooler compatible with space applications. With a minimum operational temperature of 2.8 K, this SNSPD system presents a maximum system detection efficiency of over 50% and a timing jitter of 48 ps, which paves the way for var…
Superconducting nanowire single photon detectors are a key technology for quantum information and science due to their high efficiency, low timing jitter, and low dark counts. In this work, we present a detector for single 1550 nm photons with up to 78% detection efficiency, timing jitter below 50 ps FWHM, 158 counts/s dark count rate - as well as a world-leading maximum count rate of 1.5 giga-counts/s at 3 dB compression. The PEACOQ detector (Performance-Enhanced Array for Counting Optical Quanta) comprises a linear array of 32 straight superconducting niobium nitride nanowires which span the…
With the recent achievement of extremely high-quality epitaxial interfaces between InAs nanowires and superconducting Al shells with strong superconductor-semiconductor tunnel coupling, a new regime of proximity-induced superconductivity in semiconductors can be explored where the induced gap may be similar in value to the bulk Al gap (large gap) with negligible subgap conductance (hard gap). We propose several experimentally relevant consequences of this large-gap strong-coupling regime for tunneling experiments, and we comment on the prospects of this regime for topological superconductivity…
