V. I. Telnov
This paper is the second part of my overview on photon colliders given at the conference ``The photon: its first hundred years and the future'' (PHOTON2005 + PLC2005). The first paper describes the first 25 years of the history and evolution of photon colliders. The present paper considers the photon collider at the ILC: possible parameters, technical problems and present status.
机构、总结、中文摘要均由AI分析而来，可能存在错误，请以论文正文为准。
继续探索
Midterm Status Report of the ILC Technology Network Activities
ILC技术网络中期报告总结了当前工程研究进展及国际合作情况。
An introduction and the status of R&D activities for a high-resolution, "cold" beam position monitor (BPM) and the related read-out electronics are discussed. Two different BPM detector concepts, to be attached to the SC quadrupole and located inside the ILC cryomodule, are currently under investigation: A resonant dipole-mode cavity-style BPM pickup, developed at Fermilab, and a re-entrant resonant coaxial waveguide BPM, designed by CEA-Saclay. While the 1.5 GHz dipole-mode cavity BPM is still in the R&D phase, the re-entrant BPM has already passed first beam tests, including its read-out sys…
The design of the positron source for the International Linear Collider (ILC) is still under consideration. The baseline design plans to use the electron beam for the positron production before it goes to the IP. The high-energy electrons pass a long helical undulator and generate an intense circularly polarized photon beam which hits a thin conversion target to produce $e^+e^-$ pairs. The resulting positron beam is longitudinally polarized which provides an important benefit for precision physics analyses. In this paper the status of the design studies is presented with focus on ILC250. In pa…
The design of the positron source for the International Linear Collider (ILC) is still under discussion. The baseline design plans to use the high-energy electron beam for the positron production before it goes to the IP. The electrons pass a long helical undulator and generate an intense circularly polarized photon beam which hits a thin conversion target to produce $e^+e^-$ pairs. The resulting positron beam is longitudinally polarized which provides an important benefit for precision physics analyses at the ILC. In this paper the status of the positron target design studies is presented. Fo…
During the preparatory phase of the International Linear Collider (ILC) project, all technical development and engineering design needed for the start of ILC construction must be completed, in parallel with intergovernmental discussion of governance and sharing of responsibilities and cost. The ILC Preparatory Laboratory (Pre-lab) is conceived to execute the technical and engineering work and to assist the intergovernmental discussion by providing relevant information upon request. It will be based on a worldwide partnership among laboratories with a headquarters hosted in Japan. This proposal…
A superconducting RF accelerator test facility is currently under construction at Fermilab. The accelerator will consist of an electron gun, 40 MeV injector, beam acceleration section consisting of 3 TTF-type or ILC-type cryomodules, and multiple downstream beam lines for testing diagnostics and performing beam experiments. With 3 cryomodules installed this facility will initially be capable of generating an 810 MeV electron beam with ILC beam intensity. The facility can accommodate up to 6 cryomodules for a total beam energy of 1.5 GeV. This facility will be used to test SRF cryomodules under…
A superconducting RF accelerator test facility is being constructed at Fermilab. The existing New Muon Lab (NML) building is being converted for this facility. The accelerator will consist of an electron gun, injector, beam acceleration section consisting of 3 TTF-type or ILC-type cryomodules, multiple downstream beam lines for testing diagnostics and conducting various beam tests, and a high power beam dump. When completed, it is envisioned that this facility will initially be capable of generating an 810 MeV electron beam with ILC beam intensity. Expansion plans of the facility are underway …
The current status of the 2mrad crossing angle layout for the ILC is reviewed. The scheme developed in the UK and France is described and the performance discussed for a TeV machine. Secondly, the scheme developed at SLAC and BNL is then studied and modified for a TeV machine. We find that both schemes can handle the higher energy beam with modifications, and share many common features.
The Advanced Superconducting Test Acccelerator (ASTA) is being constructed at Fermilab. The existing New Muon Lab (NML) building is being converted for this facility. The accelerator will consist of an electron gun, injector, beam acceleration section consisting of 3 TTF-type or ILC-type cryomodules, multiple downstream beamlines for testing diagnostics and conducting various beam tests, and a high power beam dump. When completed, it is envisioned that this facility will initially be capable of generating a 750-MeV electron beam with ILC beam intensity. An expansion of this facility was recent…
Status Report on the Hydrodynamic Simulations of a Tapered Plasma Lens for Optical Matching at the ILC $e^+$ Source
针对ILC正电子源高度发散束流，本文提出并模拟了锥形等离子体透镜的光学匹配方案，初步流体动力学模拟验证了其可行性，为后续实验和设计优化奠定基础。
Beginning with the first linear collider, SLC at SLAC, it was quickly discovered that high energy muons that are produced in halo collimators in the beam delivery system can cause a significant background in the experiment detector. Following publication of the ILC Technical Design Report, May 2013 [1] a simulation of this background has been made using simulation codes MUCARLO and GEANT4. It became clear that to mitigate this background, various magnetic devices were going to be needed.
In this article, we describe the key features of the recently completed technical design for the International Linear Collider (ILC), a 200-500 GeV linear electron-positron collider (expandable to 1 TeV) that is based on 1.3 GHz superconducting radio-frequency (SCRF) technology. The machine parameters and detector characteristics have been chosen to complement the Large Hadron Collider physics, including the discovery of the Higgs boson, and to further exploit this new particle physics energy frontier with a precision instrument. The linear collider design is the result of nearly twenty years …
The goal of this study is to evaluate the impact of the latest ILC beam parameters at the Interaction Point (IP), as specified in the 2013 ILC Technical Design Report (TDR), on beam losses in the extraction line. The previous beam loss evaluation was based on the parameters specified in the 2007 ILC Reference Design Report (RDR). The results of this study are compared to the results obtained in the past for the ``nominal'' and the ``low power'' (low-P) parameter options of the RDR. The initial disrupted beam distribution at IP was generated using Guinea-Pig code, and the beam losses were obtai…
The purpose of this Introduction, presented at PHOTON2007, is to provide an overview of the basic principles, possible parameters, some technical aspects and the physics program of the photon collider and discuss its status within the ILC project.
The International Linear Collider Technical Design Report (TDR) describes in four volumes the physics case and the design of a 500 GeV centre-of-mass energy linear electron-positron collider based on superconducting radio-frequency technology using Niobium cavities as the accelerating structures. The accelerator can be extended to 1 TeV and also run as a Higgs factory at around 250 GeV and on the Z0 pole. A comprehensive value estimate of the accelerator is give, together with associated uncertainties. It is shown that no significant technical issues remain to be solved. Once a site is selecte…
At this time, the design of the International Linear Collider (ILC) is optimized for e+e- collisions; the photon collider (gamma-gamma and gamma-electron) is considered as an option. Unexpected discoveries, such as the diphoton excess F(750 GeV) seen at the LHC, could strongly motivate the construction of a photon collider. In order to enable the gamma-gamma collision option, the ILC design should be compatible with it from the very beginning. In this paper, we discuss the problem of the beam crossing angle. In the ILC technical design, this angle is 14 mrad, which is just enough to provide en…
The International Linear Collider (ILC) being proposed in Japan is an electron-positron linear collider with an initial energy of 250 GeV. The ILC accelerator is based on the technology of superconducting radio-frequency cavities. This technology has reached a mature stage in the European XFEL project and is now widely used. The ILC will start by measuring the Higgs properties, providing high-precision and model-independent determinations of its parameters. The ILC at 250 GeV will also search for direct new physics in exotic Higgs decays and in pair-production of weakly interacting particles. …
The ILC beam dumps are a key part of the accelerator design. At Snowmass 2005, the current status of the beam dump designs were reviewed, and the options for the overall dump layout considered. This paper describes the available dump options for the baseline and the alternatives and considers issues for the dumps that require resolution.
A large, world-wide community of physicists is working to realise an exceptional physics program of energy-frontier, electron-positron collisions with the International Linear Collider (ILC). This program will begin with a central focus on high-precision and model-independent measurements of the Higgs boson couplings. This method of searching for new physics beyond the Standard Model is orthogonal to and complements the LHC physics program. The ILC at 250 GeV will also search for direct new physics in exotic Higgs decays and in pair-production of weakly interacting particles. Polarised electro…
This report on Photon Colliders briefly reviews three main issues: physics motivation, possible parameters and technical feasibility, plans of works and international cooperation. New scheme of laser optics at the interaction region is described which can drastically (at least by one order) reduce the cost of the laser system.
Technical Status Report on Plasma Components and Systems in the context of EuPRAXIA
本文回顾了EuPRAXIA项目中激光与束流驱动等离子体加速器组件及系统的技术现状，并评估了未来设施实施需解决的挑战。
CEPC Project Status
本文回顾粒子物理成就并展望未来，介绍了CEPC项目的进展，包括TDR完成、EDR阶段启动及Ref-TDR发布，计划于2030-2035年申请建设。
The International Linear Collider Technical Design Report (TDR) describes in four volumes the physics case and the design of a 500 GeV centre-of-mass energy linear electron-positron collider based on superconducting radio-frequency technology using Niobium cavities as the accelerating structures. The accelerator can be extended to 1 TeV and also run as a Higgs factory at around 250 GeV and on the Z0 pole. A comprehensive value estimate of the accelerator is give, together with associated uncertainties. It is shown that no significant technical issues remain to be solved. Once a site is selecte…
In this conference paper, I review the present status and technical problems of the Photon collider, as well as various additional applications of Compton scattering.
The International Linear Collider Technical Design Report (TDR) describes in four volumes the physics case and the design of a 500 GeV centre-of-mass energy linear electron-positron collider based on superconducting radio-frequency technology using Niobium cavities as the accelerating structures. The accelerator can be extended to 1 TeV and also run as a Higgs factory at around 250 GeV and on the Z0 pole. A comprehensive value estimate of the accelerator is give, together with associated uncertainties. It is shown that no significant technical issues remain to be solved. Once a site is selecte…
In the baseline design of the International Linear Collider (ILC) an undulator-based source is foreseen for the positron source in order to match the physics requirements. The baseline parameters are optimized for the ILC at sqrt(s)=500 GeV, that means an electron drive beam of 250 GeV. Precision measurements in the Higgs sector, however, require measurements at sqrt(s)=250 GeV, i.e. running with the electron drive beam only at 125 GeV, which imposes a challenge for achieving a high yield. Therefore the baseline undulator parameters have to be optimized as much as possible within their technic…
In this invited talk at the ``historical'' session of PHOTON2005, I was asked to recount the history and the development, from its earliest days to the present, of the idea of photon colliders based on conversion of high energy electrons to high-energy photons at a future high-energy linear e+e- collider. Described in this talk are the general features and schemes of a photon collider, the evolution in understanding of what the parameters of a realistic photon collider are, possible solutions of various technical problems, the physics motivation, and the present status of photon-collider devel…
扫码添加微信好友，提出您的宝贵建议 👇
💡 备注请填写：网站反馈
发表机构由 AI 从论文文本抽取，如发现错误，欢迎反馈修正建议。