arXivDaily arXiv每日学术速递 周一至周五更新
arXiv 2311.01360physics.flu-dynmath-phmath.MP
收藏

在 OpenFOAM 中采用保对称性离散化的大涡模拟最小耗散模型

Minimum-dissipation model for large-eddy simulation using symmetry-preserving discretization in OpenFOAM

J Sun, R. W. C. P Verstappen

AI总结:

本文在 OpenFOAM 中评估结合保对称性与中心差分离散的最小耗散 QR 模型,通过槽道流、圆柱、周期山丘和风力机算例验证其精度与低成本优势。

摘要:

将最小耗散模型应用于雷诺数最高达 $Re_τ=2000$ 的槽道流、$Re=3900$ 的圆柱绕流以及 $Re=10595$ 的周期性山丘绕流。数值模拟在基于有限体积法的 OpenFOAM 中完成。我们在结构化网格上同时采用了 OpenFOAM 中的保对称性离散化方法和标准二阶精度离散化方法,并将结果与 DNS 及实验数据进行比较。槽道流结果表明,静态 QR 模型的表现与动态模型同样出色,同时降低了计算成本;模型常数 $C=0.024$ 给出最准确的预测,且亚格子模型的贡献随网格分辨率提高而减小,在使用细网格时变得非常小(低于分子黏性的 0.2)。此外,QR 模型无需壁面阻尼函数即可在最高 $Re_τ=2000$ 时准确预测平均速度和均方根速度。在 $Re_τ=1000$ 时,保对称性离散化优于标准 OpenFOAM 离散化。圆柱绕流结果显示,平均速度、阻力系数和升力系数与实验数据吻合良好,且与 QR 模型结合的中心差分格式预测结果更好。针对周期性山丘绕流开展的多项比较表明,在 OpenFOAM 中有必要将中心差分格式与最小耗散模型结合使用;最佳模型常数仍为 $C=0.024$。单台风力机模拟表明,QR 模型能够在复杂旋转场景中给出准确预测。

英文摘要:

The minimum-dissipation model is applied to channel flow up to $Re_τ= 2000$, flow past a circular cylinder at $Re=3900$, and flow over periodic hills at $Re=10595$. Numerical simulations were performed in OpenFOAM which is based on the finite volume methods. We used both symmetry-preserving and standard second-order accurate discretization methods in OpenFOAM on structured meshes. The results are compared to DNS and experimental data. The results of channel flow demonstrate a static QR model performs equally well as the dynamic models while reducing the computational cost. The model constant of $C=0.024$ gives the most accurate prediction, and the contribution of the sub-grid model decreases with the increase of the mesh resolution and becomes very small (less than 0.2 molecular viscosity) if a fine mesh is used. Furthermore, the QR model is able to predict the mean and rms velocity accurately up to $Re_τ= 2000$ without a wall damping function. The symmetry-preserving discretization outperforms the standard OpenFOAM discretization at $Re_τ=1000$. The results for the flow over a cylinder show that the mean velocity, drag coefficient, and lift coefficient are in good agreement with the experimental data and the central difference schemes conjugated with the QR model predict better results. The various comparisons carried out for flows over periodic hills demonstrate the need to use central difference schemes in OpenFOAM in combination with the minimum dissipation model. The best model constant is again $C=0.024$. The single wind turbine simulation shows that the QR model is capable of predicting accurate results in complex rotating scenarios.

机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。

↑