Characterizing self-interference is essential to the design and evaluation of in-band full-duplex communication systems. Until now, little has been understood about this coupling in full-duplex systems operating at millimeter wave (mmWave) frequencies, and it has been shown that the highly-idealized models proposed for such do not align with practice. This work presents the first spatial and statistical model of mmWave self-interference backed by measurements, enabling engineers to draw realizations that exhibit the large-scale and small-scale spatial characteristics observed in our nearly 6.5 million measurements taken at 28 GHz. Core to our model is its use of system and model parameters having real-world meaning, which facilitates its extension to systems beyond our own phased array platform through proper parameterization. We demonstrate this by collecting nearly 13 million additional measurements to show that our model can generalize to two other system configurations. We assess our model by comparing it against actual measurements to confirm its ability to align spatially and in distribution with real-world self-interference. In addition, using both measurements and our model of self-interference, we evaluate an existing beamforming-based full-duplex mmWave solution to illustrate that our model can be reliably used to design new solutions and validate the performance improvements they may offer.
While initial beam alignment (BA) in millimeter-wave networks has been thoroughly investigated, most research assumes a simplified terminal model based on uniform linear/planar arrays with isotropic antennas. Devices with non-isotropic antenna elements need multiple panels to provide good spherical coverage, and exhaustive search over all beams of all the panels leads to unacceptable overhead. This paper proposes a location- and orientation-aware solution that manages the initial BA for multi-panel devices. We present three different neural network structures that provide efficient BA with a w…
We present measurements of the 28 GHz self-interference channel for full-duplex sectorized multi-panel millimeter wave (mmWave) systems, such as integrated access and backhaul. We measure the isolation between the input of a transmitting phased array panel and the output of a co-located receiving phased array panel, each of which is electronically steered across a number of directions in azimuth and elevation. In total, nearly 6.5 million measurements were taken in an anechoic chamber to densely inspect the directional nature of the coupling between 256-element phased arrays. We observe that h…
In this paper, over-the-air experiments with external and internal interferences were performed using Chalmers millimeter-wave multiple-input-multiple-output testbed MATE. The resulting SINR for both interference experiments are compared and discussed.
This paper presents an evaluation of distortion and interference sources, namely, the harmonic distortion and antenna crosstalk, originating within a 2 x 2 millimeter-wave (mm-wave) multiple-input-multiple-output (MIMO) testbed. The experience gained through the insight into the built testbed could be fed into the design of future mm-wave massive MIMO testbeds.
This paper develops a novel methodology for designing analog beamforming codebooks for full-duplex millimeter wave (mmWave) transceivers, the first such codebooks to the best of our knowledge. Our design reduces the self-interference coupled by transmit-receive beam pairs and simultaneously delivers high beamforming gain over desired coverage regions, allowing mmWave full-duplex systems to support beam alignment while minimizing self-interference. To do so, our methodology allows some variability in beamforming gain to strategically shape beams that reject self-interference while still having …
Given the overcrowding in the 300 MHz-3 GHz spectrum, millimeter wave (mmWave) spectrum is a promising candidate for the future generations of wireless networks. With the unique propagation characteristics at mmWave frequencies, one of the fundamental questions to address is whether mmWave networks are noise or interference-limited. The regime in which the network operates significantly impacts the MAC layer design, resource allocation procedure and also interference management techniques. In this paper, we first derive the statistical characteristic of the cumulative interference in finite-si…
We study the distribution of the interference power in a millimeter wave (mmWave) cellular network. Such interference is random and highly dependent on the employed transmission technique, as well as the varying channel conditions and the varying association between users and base stations. Traditional networks at lower frequencies usually employ omnidirectional transmission which creates an (almost) equal amount of interference in any direction. MmWave networks, however, must employ directional beamforming transmission in order to compensate for the high path loss in mmWave frequency bands. T…
Power consumption is a key challenge in millimeter wave (mmWave) receiver front-ends, due to the need to support high dimensional antenna arrays at wide bandwidths. Recently, there has been considerable work in developing low-power front-ends, often based on low-resolution ADCs and low-power mixers. A critical but less studied consequence of such designs is the relatively low-dynamic range which in turn exposes the receiver to adjacent carrier interference and blockers. This paper provides a general mathematical framework for analyzing the performance of mmWave front-ends in the presence of ou…
The potential of the millimeter wave (mmWave) band in meeting the ever growing demand for high data rate and capacity in emerging fifth generation (5G) wireless networks is well-established. Since mmWave systems are expected to use highly directional antennas with very focused beams to overcome severe pathloss and shadowing in this band, the nature of signal propagation in mmWave wireless networks may differ from current networks. One factor that is influenced by such propagation characteristics is the interference behavior, which is also impacted by simultaneous use of the unlicensed portion …
There have been recent works on enabling in-band full-duplex operation using millimeter-wave (mmWave) transceivers. These works are based solely on creating sufficient isolation between a transceiver's transmitter and receiver via multiple-input multiple-output (MIMO) precoding and combining. In this work, we propose supplementing these beamforming strategies with analog self-interference cancellation (A-SIC). By leveraging A-SIC, a portion of the self-interference is cancelled without the need for beamforming, allowing for more optimal beamforming strategies to be used in serving users. We us…
This work develops LoneSTAR, a novel enabler of full-duplex millimeter wave (mmWave) communication systems through the design of analog beamforming codebooks. LoneSTAR codebooks deliver high beamforming gain and broad coverage while simultaneously reducing the self-interference coupled by transmit and receive beams at a full-duplex mmWave transceiver. Our design framework accomplishes this by tolerating some variability in transmit and receive beamforming gain to strategically shape beams that reject self-interference spatially while accounting for digitally-controlled analog beamforming netwo…
Smart Repeaters (SR) can potentially enhance the coverage in Millimeter-wave (mmWave) wireless communications. However, the angular coverage of the existing two-panel SR is too limited to make the SR a truly cost-effective mmWave range extender. This paper proposes the usage of a tri-sectoral Advanced SR (ASR) to extend the angular coverage with respect to conventional SR. We propose a multi-user precoder optimization for ASR in a downlink multi-carrier communication system to maximize the number of served User Equipments (UEs) while guaranteeing constraints on per-UE rate and time-frequency r…
Modern millimeter wave (mmWave) communication systems rely on beam alignment to deliver sufficient beamforming gain to close the link between devices. We present a novel beam selection methodology for multi-panel, full-duplex mmWave systems, which we call STEER, that delivers high beamforming gain while significantly reducing the full-duplex self-interference coupled between the transmit and receive beams. STEER does not necessitate changes to conventional beam alignment methodologies nor additional over-the-air feedback, making it compatible with existing cellular standards. Instead, STEER us…
Picocellular architectures are essential for providing the spatial reuse required to satisfy the ever-increasing demand for mobile data. A key deployment challenge is to provide backhaul connections with sufficiently high data rate. Providing wired support (e.g., using optical fiber) to pico base stations deployed opportunistically on lampposts and rooftops is impractical, hence wireless backhaul becomes an attractive approach. A multihop mesh network comprised of directional millimeter wave links is considered here for this purpose. The backhaul design problem is formulated as one of joint ro…
Equipping millimeter wave (mmWave) systems with full-duplex capability would accelerate and transform next-generation wireless applications and forge a path for new ones. Full-duplex mmWave transceivers could capitalize on the already attractive features of mmWave communication by supplying spectral efficiency gains and latency improvements while also affording future networks with deployment solutions in the form of interference management and wireless backhaul. Foreseeable challenges and obstacles in making mmWave full-duplex a reality are presented in this article along with noteworthy unkn…
Deploying sub-6GHz network together with millimeter wave (mmWave) is a promising solution to simultaneously achieve sufficient coverage and high data rate. In the heterogeneous networks (HetNets), the traditional coupled access, i.e., the users are constrained to be associated with the same base station in both downlink and uplink, is no longer optimal, and the concept of downlink and uplink decoupling has recently been proposed. In this paper, we propose an analytical framework to investigate the traditional sub-6GHz HetNets integrating with mmWave small cells (SCells) with decoupled access, …
Full Duplex (FD) communication can revolutionize wireless communications as it avoids using independent channels for bi-directional communications. This work generalizes the point-to-point FD communication in millimeter wave (mmWave) band consisting of K-pairs of massive MIMO FD nodes operating simultaneously. We present a novel joint hybrid beamforming (HYBF) and combining scheme for weighted sum-rate (WSR) maximization to enable the coexistence of massive MIMO FD links cost-efficiently. The proposed algorithm relies on alternative optimization based on the minorization-maximization method. M…
The wide bandwidths available at millimeter-wave (mmWave) frequencies have offered exciting potential to wireless communication systems and radar alike. Communication systems can offer higher rates and support more users with mmWave bands while radar systems can benefit from higher resolution captures. This leads to the possibility that portions of mmWave spectrum will be occupied by both communication and radar (e.g., 60 GHz industrial, scientific, and medical (ISM) band). This potential coexistence motivates the work of this paper, in which we present a design that can enable simultaneous, i…
We study whether realistic 5G mm-wave cellular networks would cause harmful out-of-band interference to weather satellites sensing in the 23.8 GHz band. We estimate uplink and downlink interference from a single interferer and a network of interferers in New York City, using real 3D building data and realistic antenna patterns. We perform detailed ray-tracing propagation simulations, for locations of the MetOp-B weather satellite and its scanning orientations and ground interferer antenna orientations for representative urban cell sites. In addition to the ITU-R threshold of -136 dBm/200 MHz, …
Exploiting the millimeter wave (mmWave) band has recently attracted considerable attention as a potential solution to widespread deployment of device-to-device (D2D) communication challenges, namely, spectrum scarcity and interference. However, its directional nature makes the utilization of mmWave band a challenging task as it requires careful beam alignment between the D2D transmitter and receiver. In this paper, we investigate the impact of inaccurate angle-of-arrival (AoA) estimation as a beam alignment impairment on the performance of a directional mmWave D2D network. We have used tools f…
Millimeter wave (mmWave) and terahertz MIMO systems rely on pre-defined beamforming codebooks for both initial access and data transmission. However, most of the existing codebooks adopt pre-defined beams that focus mainly on improving the gain of their target users, without taking interference into account, which could incur critical performance degradation in dense networks. To address this problem, in this paper, we propose a sample-efficient digital twin-assisted beam pattern design framework that learns how to form the beam pattern to reject the signals from the interfering directions. Th…
Employing large antenna arrays is a key characteristic of millimeter wave (mmWave) and terahertz communication systems. Due to the hardware constraints and the lack of channel knowledge, codebook based beamforming/combining is normally adopted to achieve the desired array gain. However, most of the existing codebooks focus only on improving the gain of their target user, without taking interference into account. This can incur critical performance degradation in dense networks. In this paper, we propose a sample-efficient online reinforcement learning based beam pattern design algorithm that l…
In this paper, a full-duplex unmanned aerial vehicle (FD-UAV) relay is employed to increase the communication capacity of millimeter-wave (mmWave) networks. Large antenna arrays are equipped at the source node (SN), destination node (DN), and FD-UAV relay to overcome the high path loss of mmWave channels and to help mitigate the self-interference at the FD-UAV relay. Specifically, we formulate a problem for maximization of the achievable rate from the SN to the DN, where the UAV position, analog beamforming, and power control are jointly optimized. Since the problem is highly non-convex and in…
In this letter, we investigate the millimeter wave (mmWave) downlink multiuser multiple-input multiple-output (MU-MIMO) system, adopting the dynamic subarray architecture at the base station and considering the multi-stream communication for each user. Aiming at maximizing the system spectral efficiency, we propose a novel hybrid beamforming design. First, assuming no inter-user interference (IUI), we easily get the optimal fully-digital beamformers and combiners using the singular value decomposition of each user channel and the waterfilling algorithm. Then, based on the obtained fullydigital…
We present measurements and analysis of self-interference in multi-panel millimeter wave (mmWave) full-duplex communication systems at 28 GHz. In an anechoic chamber, we measure the self-interference power between the input of a transmitting phased array and the output of a colocated receiving phased array, each of which is electronically steered across a number of directions in azimuth and elevation. These self-interference power measurements shed light on the potential for a full-duplex communication system to successfully receive a desired signal while transmitting in-band. Our nearly 6.5 m…
In this paper we present the first comprehensive study of the multi-user capacity of millimeter-wave (mm-wave) urban cellular networks, using site-specific ray-tracing propagation data and realistic antenna array patterns. We compare the performance of TDMA and SDMA (time and spatial division multiple access, respectively) for diverse network scenarios and antenna configurations. We propose a greedy heuristic algorithm to solve the network-wide directional link allocation problem, thereby estimating the achievable capacity and coverage of multi-user mm-wave networks. Our results show that inte…
In recent years, there has been extensive research on millimeter-wave (mmWave) communication and on in-band full-duplex (FD) communication, but work on the combination of the two is relatively lacking. FD mmWave systems could offer increased spectral efficiency and decreased latency while also suggesting the redesign of existing mmWave applications. While FD technology has been well-explored for sub-6 GHz systems, the developed methods do not translate well to mmWave. This turns us to a method called beamforming cancellation (BFC), where the highly directional mmWave beams are steered to mitig…
Millimeter (mm) wave picocellular networks are a promising approach for delivering the 1000-fold capacity increase required to keep up with projected demand for wireless data: the available bandwidth is orders of magnitude larger than that in existing cellular systems, and the small carrier wavelength enables the realization of highly directive antenna arrays in compact form factor, thus drastically increasing spatial reuse. In this paper, we carry out an interference analysis for mm-wave picocells in an urban canyon with a dense deployment of base stations. Each base station sector can serve …
Using out-of-band (OOB) side-information has recently been shown to accelerate beam selection in single-user millimeter wave (mmWave) massive MIMO communications. In this paper, we propose a novel OOB-aided beam selection framework for a mmWave uplink multi-user system. In particular, we exploit spatial information extracted from lower (sub-6 GHz) bands in order to assist with an inter-user coordination scheme at mmWave bands. To enforce coordination, we propose an exchange protocol exploiting device-to-device communications, where low-rate beam-related information is exchanged between the mob…
Millimeter wave (mmWave) communication is expected to play an important role in next generation cellular networks, aiming to cope with the bandwidth shortage affecting conventional wireless carriers. Using side-information has been proposed as a potential approach to accelerate beam selection in mmWave massive MIMO (m-MIMO) communications. However, in practice, such information is not error-free, leading to performance degradation. In the multi-user case, a wrong beam choice might result in irreducible inter-user interference at the base station (BS) side. In this paper, we consider location-a…
Wireless communication systems can be enhanced at the link level, in medium access, and at the network level when transceivers are equipped with full-duplex capability: the transformative ability to simultaneously transmit and receive over the same frequency spectrum. Effective methods to cancel self-interference are required to facilitate full-duplex operation, which we overview herein in the context of traditional radios, along with those in next-generation wireless networks. We highlight advances in self-interference cancellation that leverage machine learning, and we summarize key consider…
In this paper, we consider a hybrid millimeter wave (mmWave) and micro wave ($μ$Wave) network from the perspective of \emph{wireless caching} and study the optimal probabilistic content/file caching placement at desirable base stations (BSs) using a stochastic geometric framework. Considering the average success probability (ASP) of file delivery as the performance metric, we derive expressions for the association probability of the typical user to the mmWave and $μ$Wave networks. Accordingly, we provide an upper bound for the ASP of file delivery and formulate the content caching placement sc…
This paper investigates the application of non-orthogonal multiple access in millimeter-Wave communications (mmWave-NOMA). Particularly, we consider downlink transmission with a hybrid beamforming structure. A user grouping algorithm is first proposed according to the channel correlations of the users. Whereafter, a joint hybrid beamforming and power allocation problem is formulated to maximize the achievable sum rate, subject to a minimum rate constraint for each user. To solve this non-convex problem with high-dimensional variables, we first obtain the solution of power allocation under arbi…
The use of Millimeter-wave (mmWave) spectrum in cellular communications has recently attracted growing interest to support the expected massive increase in traffic demands. However, the high path-loss at mmWave frequencies poses severe challenges. In this paper, we analyze the potential coverage gains of using unmanned aerial vehicles (UAVs), as hovering relays, in integrated access and backhaul (IAB) mmWave cellular scenarios. Specifically, we utilize the WinProp software package, which employs ray tracing methodology, to study the propagation characteristics of outdoor mmWave channels at 30 …
The surging capacity demands of 5G networks and the limited coverage distance of high frequencies like millimeter wave (mmW) and sub-terahertz (THz) bands have led to consider the upper 6GHz (U6G) spectrum for radio access. However, due to the presence of the existing satellite (SAT) services in these bands, it is crucial to evaluate the impact of the interference of terrestrial U6G stations to SAT systems. A comprehensive study on the aggregated U6G-to-SAT interference is still missing in the literature. In this paper, we propose a stochastic model of interference (SMI) to evaluate the U6G-to…
Fifth generation (5G) wireless technology is expected to utilize highly directive antennas at millimeter wave (mmWave) spectrum to offer higher data rates. However, given the high directivity of antennas and adverse propagation characteristics at mmWave frequencies, these signals are very susceptible to obstacles. One of the important factors that are highly impacted is interference behavior. In fact, signals received from other terminals can be easily blocked or attenuated at the receiver. In addition, higher number of terminals can transmit signals without introducing much interference and h…
In this paper, using the stochastic geometry, we develop a tractable uplink modeling framework for the outage probability of both the single and multi-tier millimeter wave (mmWave) cellular networks. Each tier's mmWave base stations (BSs) are randomly located and they have particular spatial density, antenna gain, receiver sensitivity, blockage parameter and pathloss exponents. Our model takes account of the maximum power limitation and the per-user power control. More specifically, each user, which could be in line-of-sight (LOS) or non-LOS to its serving mmWave BS, controls its transmit powe…
The synergetic gains of spectrum sharing and millimeter wave communication networks have recently attracted attention, owing to the interference canceling benefits of highly-directional beamforming in such systems. In principle, fine-tuned coordinated scheduling and beamforming can drastically reduce cross-operator interference. However, this goes at the expense of the exchange of global channel state information, which is not realistic in particular when considering inter-operator coordination. Indeed, such an exchange of information is expensive in terms of backhaul infrastructure, and besid…
Delay alignment modulation (DAM) is a novel wideband communication technique, which exploits the high spatial resolution and multi-path sparsity of millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems to mitigate inter-symbol interference (ISI), without relying on conventional techniques like channel equalization or multi-carrier transmission. In this paper, we extend the DAM technique to multi-user mmWave massive MIMO communication systems. We first provide asymptotic analysis by showing that when the number of base station (BS) antennas is much larger than the total…
With the overcrowded sub-6 GHz bands, millimeter wave (mmWave) bands offer a promising alternative for the next generation wireless standard, i.e., 5G. However, the susceptibility of mmWave signals to severe pathloss and shadowing requires the use of highly directional antennas to overcome such adverse characteristics. Building a network with directional beams changes the interference behavior, since, narrow beams are vulnerable to blockages. Such sensitivity to blockages causes uncertainty in the active interfering node locations. Configuration uncertainty may also manifest in the spectral do…
In millimeter-wave (MMW) multiple-input multiple-output (MIMO) communications, users and their corresponding base station (BS) have to align their beam during both initial access and data transmissions to compensate for the high propagation loss. The beam alignment (BA) procedure specified for 5th Generation (5G) New Radio (NR) has been designed to be fast and precise in the presence of non-malicious interference and noise. A smart jammer might exploit this weakness and may launch an attack during the BA phase in order to degrade the accuracy of beam selection and, thus, adversely impacting th…
Full-duplex (FD) systems have the capability to transmit and receive at the same time in the same frequency band. FD systems can reduce congestion and latency and improve coverage and spectral efficiency. As a relay, they can increase range and decrease outages. Full-duplex (FD) wireless systems have been emerging as a practical solution to provide high bandwidth, low latency, and big data processing in millimeter wave and Terahertz systems to support cellular networks, autonomous driving, platooning, advanced driving assistance and other systems. However, FD systems suffer from loopback self-…
We investigate beam training and allocation for multiuser millimeter wave massive MIMO systems. An orthogonal pilot based beam training scheme is first developed to reduce the number of training times, where all users can simultaneously perform the beam training with the base station (BS). As the number of users increases, the same beam from the BS may point to different users, leading to beam conflict and multiuser interference. Therefore, a quality-of-service (QoS) constrained (QC) beam allocation scheme is proposed to maximize the equivalent channel gain of the QoS-satisfied users, under th…
The UFMC modulation is among the most considered solutions for the realization of beyond-OFDM air interfaces for future wireless networks. This paper focuses on the design and analysis of an UFMC transceiver equipped with multiple antennas and operating at millimeter wave carrier frequencies. The paper provides the full mathematical model of a MIMO-UFMC transceiver, taking into account the presence of hybrid analog/digital beamformers at both ends of the communication links. Then, several detection structures are proposed, both for the case of single-packet isolated transmission, and for the c…
Aiming at maximizing the achievable sum-rate of wideband multiuser mmWave massive MIMO systems, the hybrid precoding is studied. Since each computation of the achievable sum-rate can be performed only after the analog precoder and digital precoder are both determined, the maximization of the achievable sum-rate has intractable computational complexity. By introducing the interference free (IF) achievable sum-rate, the design of the analog and digital precoders can be decoupled. To avoid the beam conflict and maximize the IF achievable sum-rate, a Hungarian-based codeword selection algorithm is…
Full Duplex (FD) radio has emerged as a promising solution to increase the data rates by up to a factor of two via simultaneous transmission and reception in the same frequency band. This paper studies a novel hybrid beamforming (HYBF) design to maximize the weighted sum-rate (WSR) in a single-cell millimeter wave (mmWave) massive multiple-input-multiple-output (mMIMO) FD system. Motivated by practical considerations, we assume that the multi-antenna users and hybrid FD base station (BS) suffer from the limited dynamic range (LDR) noise due to non-ideal hardware and an impairment aware HYBF ap…
