We investigate the fundamental multiple access (MA) scheme in an active intelligent reflecting surface (IRS) aided energy-constrained Internet-of-Things (IoT) system, where an active IRS is deployed to assist the uplink transmission from multiple IoT devices to an access point (AP). Our goal is to maximize the sum throughput by optimizing the IRS beamforming vectors across time and resource allocation. To this end, we first study two typical active IRS aided MA schemes, namely time division multiple access (TDMA) and non-orthogonal multiple access (NOMA), by analytically comparing their achievable sum throughput and proposing corresponding algorithms. Interestingly, we prove that given only one available IRS beamforming vector, the NOMA-based scheme generally achieves a larger throughput than the TDMA-based scheme, whereas the latter can potentially outperform the former if multiple IRS beamforming vectors are available to harness the favorable time selectivity of the IRS. To strike a flexible balance between the system performance and the associated signaling overhead incurred by more IRS beamforming vectors, we then propose a general hybrid TDMA-NOMA scheme with user grouping, where the devices in the same group transmit simultaneously via NOMA while devices in different groups occupy orthogonal time slots. By controlling the number of groups, the hybrid TDMA-NOMA scheme is applicable for any given number of IRS beamforming vectors available. Despite of the non-convexity of the considered optimization problem, we propose an efficient algorithm based on alternating optimization. Simulation results illustrate the practical superiorities of the active IRS over the passive IRS in terms of the coverage extension and supporting multiple energy-limited devices, and demonstrate the effectiveness of our proposed hybrid MA scheme for flexibly balancing the performance-cost tradeoff.
In this letter, we consider an intelligent reflecting surface (IRS)-aided wireless relaying system, where a decode-and-forward relay (R) is employed to forward data from a source (S) to a destination (D), aided by M passive reflecting elements. We consider two practical IRS deployment strategies, namely, single-IRS deployment where all reflecting elements are mounted on one single IRS that is deployed near S, R, or D, and multi-IRS deployment where the reflecting elements are allocated over three separate IRSs which are deployed near S, R, and D, respectively. Under the line-of-sight (LoS) cha…
Intelligent reflecting surface (IRS) is a promising technology to support high performance wireless communication. By adaptively configuring the reflection amplitude and/or phase of each passive reflecting element on it, the IRS can reshape the electromagnetic environment in favour of signal transmission. This letter advances the existing research by proposing and analyzing a double-IRS aided wireless communication system. Under the reasonable assumption that the reflection channel from IRS 1 to IRS 2 is of rank 1 (e.g., line-of-sight channel), we propose a joint passive beamforming design for…
This paper investigates multiple intelligent reflecting surfaces (IRSs) aided wireless network, where the IRSs are deployed to cooperatively assist communications between a multi-antenna base station (BS) and multiple single-antenna cell-edge users. We aim at maximizing the weighted sum rate of all the cell-edge users by jointly optimizing the BS's transmit beamforming and IRS's phase shifts. Especially, the beamforming is optimally solved by the Lagrangian method, and the phase shifts are obtained based on the Riemannian manifold conjugate gradient (RMCG) method. Numerical results show that a…
This paper considers an active intelligent reflecting surface (IRS)-aided wireless powered communication network (WPCN), where devices first harvest energy and then transmit information to a hybrid access point (HAP). Different from the existing works on passive IRS-aided WPCNs, this is the first work that introduces the active IRS in WPCNs. To guarantee fairness, the problem is formulated as an amplifying power-limited weighted sum throughput (WST) maximization problem, which is solved by successive convex approximation technique and fractional programming alternatively. To balance the perfor…
Intelligent reflecting surface (IRS) has shown its effectiveness in facilitating orthogonal time-division integrated sensing and communications (TD-ISAC), in which the sensing task and the communication task occupy orthogonal time-frequency resources, while the role of IRS in the more interesting scenarios of non-orthogonal ISAC (NO-ISAC) systems has so far remained unclear. In this paper, we consider an IRS-aided NO-ISAC system, where a distributed IRS is deployed to assist concurrent communication and location sensing for a blind-zone user, occupying non-orthogonal/overlapped time-frequency …
Intelligent reflecting surface (IRS) as a promising technology rendering high throughput in future communication systems is compatible with various communication techniques such as non-orthogonal multiple-access (NOMA). In this paper, the downlink transmission of IRS-assisted NOMA communication is considered while undergoing imperfect channel state information (CSI). Consequently, a robust IRS-aided NOMA design is proposed by solving the sum-rate maximization problem to jointly find the optimal beamforming vectors for the access point and the passive reflection matrix for the IRS, using the pe…
We study the beamforming optimization for an intelligent reflecting surface (IRS)-aided full-duplex (FD) communication system in this letter. Specifically, we maximize the sum rate of bi-directional transmissions by jointly optimizing the transmit beamforming and the beamforming of the IRS reflection. A fast converging alternating algorithm is developed to tackle this problem. In each iteration of the proposed algorithm, the solutions to the transmit beamforming and the IRS reflect beamforming are obtained in a semi-closed form and a closed form, respectively. Compared to an existing method ba…
Prior studies on intelligent reflecting surface (IRS) have mostly considered wireless communication systems aided by a single passive IRS, which, however, has limited control over wireless propagation environment and suffers severe product-distance path-loss. To address these issues, we propose in this paper a new multi-active multi-passive (MAMP)-IRS aided wireless communication system, where a number of active and passive IRSs are deployed to assist the downlink communication in complex environment, by establishing a multi-hop reflection path across active and passive IRSs. An optimization p…
Intelligent reflecting surface (IRS)-aided communication is a promising technology for beyond 5G (B5G) systems, to reconfigure the radio environment proactively. However, IRS-aided communication in practice requires efficient channel estimation or passive beam training, whose overhead and complexity increase drastically with the number of reflecting elements/beam directions. To tackle this challenge, we propose in this paper a novel environment-aware joint active and passive beam selection scheme for IRS-aided wireless communication, based on the new concept of channel knowledge map (CKM). Spe…
Intelligent reflecting surface (IRS) has emerged as a promising technique for wireless communication networks. By dynamically tuning the reflection amplitudes/phase shifts of a large number of passive elements, IRS enables flexible wireless channel control and configuration, and thereby enhances the wireless signal transmission rate and reliability significantly. Despite the vast literature on designing and optimizing assorted IRS-aided wireless systems, prior works have mainly focused on enhancing wireless links with single signal reflection only by one or multiple IRSs, which may be insuffic…
Intelligent reflecting surface (IRS) has been considered as a promising technology to alleviate the blockage effect and enhance coverage in millimeter wave (mmWave) communication. To explore the impact of IRS on the performance of mmWave communication, we investigate a multi-IRS assisted mmWave communication network and formulate a sum rate maximization problem by jointly optimizing the active and passive beamforming and the set of IRSs for assistance. The optimization problem is intractable due to the lack of convexity of the objective function and the binary nature of the IRS selection varia…
Spectrum sensing is a key enabling technique for cognitive radio (CR), which provides essential information on the spectrum availability. However, due to severe wireless channel fading and path loss, the primary user (PU) signals received at the CR or secondary user (SU) can be practically too weak for reliable detection. To tackle this issue, we consider in this letter a new intelligent reflecting surface (IRS)-aided spectrum sensing scheme for CR, by exploiting the large aperture and passive beamforming gains of IRS to boost the PU signal strength received at the SU to facilitate its spectru…
In this paper, we focus on intelligent reflecting surface (IRS) assisted multi-antenna communications with transceiver hardware impairments encountered in practice. In particular, we aim to maximize the received signal-to-noise ratio (SNR) taking into account the impact of hardware impairments, where the source transmit beamforming and the IRS reflect beamforming are jointly designed under the proposed optimization framework. To circumvent the non-convexity of the formulated design problem, we first derive a closed-form optimal solution to the source transmit beamforming. Then, for the optimiz…
This paper considers an intelligent reflecting surface(IRS)-aided wireless powered communication network (WPCN), where devices first harvest energy from a power station (PS) in the downlink (DL) and then transmit information using non-orthogonal multiple access (NOMA) to a data sink in the uplink (UL). However, most existing works on WPCNs adopted the simplified linear energy-harvesting model and also cannot guarantee strict user quality-of-service requirements. To address these issues, we aim to minimize the total transmit energy consumption at the PS by jointly optimizing the resource alloca…
Intelligent reflecting surface (IRS) is an emerging technology that is able to significantly improve the performance of wireless communications, by smartly tuning signal reflections at a large number of passive reflecting elements. On the other hand, with ubiquitous wireless devices and ambient radio-frequency signals, wireless sensing has become a promising new application for the next-generation/6G wireless networks. By synergizing low-cost IRS and fertile wireless sensing applications, this article proposes a new IRS-aided sensing paradigm for enhancing the performance of wireless sensing c…
Intelligent reflecting surface (IRS) has emerged as a promising technique to control wireless propagation environment for enhancing the communication performance cost-effectively. However, the rapidly time-varying channel in high-mobility communication scenarios such as vehicular communication renders it challenging to obtain the instantaneous channel state information (CSI) efficiently for IRS with a large number of reflecting elements. In this paper, we propose a new roadside IRS-aided vehicular communication system to tackle this challenge. Specifically, by exploiting the symmetrical deploy…
Intelligent reflecting surface (IRS) is an emerging technology for wireless communication composed of a large number of low-cost passive devices with reconfigurable parameters, which can reflect signals with a certain phase shift and is capable of building programmable communication environment. In this paper, to avoid the high hardware cost and energy consumption in spatial modulation (SM), an IRS-aided hybrid secure SM (SSM) system with a hybrid precoder is proposed. To improve the security performance, we formulate an optimization problem to maximize the secrecy rate (SR) by jointly optimiz…
Active intelligent reflecting surface (IRS) enables flexible signal reflection control with \emph{power amplification}, thus effectively compensating the product-distance path-loss in conventional passive-IRS aided systems. In this letter, we characterize the communication performance of an active-IRS aided single-cell wireless network. To this end, we first propose a \emph{customized} IRS deployment strategy, where the active IRSs are uniformly deployed within a ring concentric with the cell to serve the users far from the base station. Next, given the Nakagami-$m$ fading channel, we characte…
This paper investigates the joint design of the beamforming scheme in intelligent reflecting surface (IRS) assisted multiuser (MU) multiple-input multiple-output (MIMO) downlink transmissions. Channel estimation errors associated with the minimum mean square error (MMSE) estimation are assumed and the weighted sum rate (WSR) is adopted as the performance metric. Low-resolution phase shifters (PSs) in practical implementations are taken into account as well. Under the constraint of the transmit power and discrete phase shifters (PSs), an optimization problem is formulated to maximize the WSR of…
This paper proposes a novel framework of resource allocation in multi-cell intelligent reflecting surface (IRS) aided non-orthogonal multiple access (NOMA) networks, where an IRS is deployed to enhance the wireless service. The problem of joint user association, subchannel assignment, power allocation, phase shifts design, and decoding order determination is formulated for maximizing the achievable sum rate. The challenging mixed-integer non-linear problem is decomposed into an optimization subproblem (P1) with continuous variables and a matching subproblem (P2) with integer variables. In an e…
This paper studies intelligent reflecting surface (IRS)-aided full-duplex (FD) wireless-powered communication network (WPCN), where a hybrid access point (HAP) broadcasts energy signals to multiple devices for their energy harvesting in the downlink (DL) and meanwhile receives information signals in the uplink (UL) with the help of IRS. Particularly, we propose three types of IRS beamforming configurations to strike a balance between the system performance and signaling overhead as well as implementation complexity. We first propose the fully dynamic IRS beamforming, where the IRS phase-shift …
In this letter, we study the resource allocation for a multiuser intelligent reflecting surface (IRS)-aided simultaneous wireless information and power transfer (SWIPT) system. Specifically, a multi-antenna base station (BS) transmits energy and information signals simultaneously to multiple energy harvesting receivers (EHRs) and information decoding receivers (IDRs) assisted by an IRS. Under this setup, we introduce a multi-objective optimization (MOOP) framework to investigate the fundamental trade-off between the data sum-rate maximization and the total harvested energy maximization, by joi…
Channel estimation is a practical challenge for intelligent reflecting surface (IRS) aided wireless communication. As the number of IRS reflecting elements or IRS-aided users increases, the channel training overhead becomes excessively high, which results in long delay and low throughput in data transmission. To tackle this challenge, we propose in this paper a new anchor-assisted channel estimation approach, where two anchor nodes, namely A1 and A2, are deployed near the IRS for facilitating its aided base station (BS) in acquiring the cascaded BS-IRS-user channels required for data transmiss…
The performance of Simultaneous Wireless Information and Power Transfer (SWIPT) is mainly constrained by the received Radio-Frequency (RF) signal strength. To tackle this problem, we introduce an Intelligent Reflecting Surface (IRS) to compensate the propagation loss and boost the transmission efficiency. This paper proposes a novel IRS-aided SWIPT system where a multi-carrier multi-antenna Access Point (AP) transmits information and power simultaneously, with the assist of an IRS, to a single-antenna User Equipment (UE) employing practical receiving schemes. Considering harvester nonlinearity…
Intelligent reflecting surfaces (IRSs) are promising enablers for high-capacity wireless communication systems by constructing favorable channels between the transmitter and receiver. However, general, accurate, and tractable outage analysis for IRS-aided multiple-input-multiple-output (MIMO) systems is not available in the literature. In this paper, we first characterize the mutual information (MI) of IRS-aided MIMO systems by capitalizing on large random matrix theory (RMT). Based on this result, a closed-form approximation for the outage probability is derived and a gradient-based algorithm…
This paper investigates the achievable rate region of the multiple-input single-output (MISO) interference channel aided by intelligent reflecting surfaces (IRSs). We exploit the the additional design degree of freedom provided by the coordinated IRSs to enhance the desired signal and suppress interference so as to enlarge the achievable rate region of the interference channel. To this end, we jointly optimize the active transmit beamforming at the transmitters and passive reflective beamforming at the IRSs, subject to the constant modulus constraints of reflective beamforming vectors. To addr…
Intelligent reflecting surface (IRS) has been deemed as a transformative technology to achieve smart and reconfigurable environment for wireless communication. This letter studies a new IRS-aided communication system, where multiple IRSs assist in the communication between a multi-antenna base station (BS) and a remote single-antenna user by multi-hop signal reflection. Specifically, by exploiting the line-of-sight (LoS) link between nearby IRSs, a multi-hop cascaded LoS link between the BS and user is established where a set of IRSs are selected to successively reflect the BS's signal, so tha…
In this paper, we study the waveform and passive beamforming design for intelligent reflecting surface (IRS)-aided wireless power transfer (WPT). Generalized multi-user and low complexity single-user algorithms are derived based on alternating optimization (AO) framework to maximize the weighted sum output DC current, subject to transmit power constraints and passive beamforming phases unit modulus constraints. The input signal waveform and IRS passive beamforming phase shifts are jointly designed as a function of users' individual frequency-selective channel state information (CSI). The energ…
Prior studies on intelligent reflecting surface (IRS) have mostly considered wireless communication systems aided by a single passive IRS, which, however, has limited control over wireless propagation environment and suffers from product-distance path-loss. To address these issues, we propose in this paper a new hybrid active/passive IRS aided wireless communication system, where an active IRS and multiple passive IRSs are deployed to assist the communication between a base station (BS) and a remote user in complex environment, by establishing a multihop reflection path across active/passive I…
In this paper, we develop a unified dynamic intelligent reflecting surface (IRS) beamforming framework to boost the sum computation rate of an IRS-aided mobile edge computing (MEC) system, where each device follows a binary offloading policy. Specifically, the task of each device has to be either executed locally or offloaded to MEC servers as a whole with the aid of given number of IRS beamforming vectors available. By flexibly controlling the number of IRS reconfiguration times, the system can achieve a balance between the performance and associated signalling overhead. We aim to maximize th…
Intelligent reflecting surface (IRS) is a promising technology for achieving spectrum and energy efficient wireless networks cost-effectively. Most existing works on IRS have focused on exploiting IRS to enhance the performance of wireless communication or wireless information transmission (WIT), while its potential for boosting the efficiency of radio-frequency (RF) wireless energy transmission (WET) still remains largely open. Although IRS-aided WET shares similar characteristics with IRS-aided WIT, they differ fundamentally in terms of design objective, receiver architecture, and practical …
In this paper, we propose a robust design framework for IRS-aided communication systems in the presence of user location uncertainty. By jointly designing the transmit beamforming vector at the BS and phase shifts at the IRS, we aim to minimize the transmit power subject to the worse-case quality of service (QoS) constraint, i.e., ensuring the user rate is above a threshold for all possible user location error realizations. With unit-modulus, this problem is not convex. The location uncertainty in the QoS constraint further increases the difficulty of solving this problem. By utilizing techniq…
This paper proposes a novel relay-aided intelligent reconfigurable surface (IRS) architecture for future wireless communication systems. The proposed architecture, which consists of two side-by-side intelligent surfaces connected via a full-duplex relay, has the potential of achieving the promising gains of intelligent surfaces while requiring much smaller numbers of reflecting elements. Consequently, the proposed IRS architecture needs significantly less channel estimation and beam training overhead and provides higher robustness compared to classical IRS approaches. Further, thanks to dividi…
In this paper, we propose a new dynamic IRS beamforming framework to boost the sum throughput of an intelligent reflecting surface (IRS) aided wireless powered communication network (WPCN). Specifically, the IRS phase-shift vectors across time and resource allocation are jointly optimized to enhance the efficiencies of both downlink wireless power transfer (DL WPT) and uplink wireless information transmission (UL WIT) between a hybrid access point (HAP) and multiple wirelessly powered devices. To this end, we first study three special cases of the dynamic IRS beamforming,namely user-adaptive I…
In this paper, we investigate the problem of pilot optimization and channel estimation of two-way relaying network (TWRN) aided by an intelligent reflecting surface (IRS) with finite discrete phase shifters. In a TWRN, there exists a challenging problem that the two cascading channels from source-to-IRS-to-Relay and destination-to-IRS-to-relay interfere with each other. Via designing the initial phase shifts of IRS and pilot pattern, the two cascading channels are separated by using simple arithmetic operations like addition and subtraction. Then, the least-squares estimator is adopted to esti…
We introduce a novel system setup where a backscatter device operates in the presence of an intelligent reflecting surface (IRS). In particular, we study the bistatic backscatter communication (BackCom) system assisted by an IRS. The phase shifts at the IRS are optimized jointly with the transmit beamforming vector of the carrier emitter to minimize the transmit power consumption at the carrier emitter whilst guaranteeing a required BackCom performance. The unique channel characteristics arising from multiple reflections at the IRS render the optimization problem highly non-convex. Therefore, …
An intelligent reflecting surface (IRS)-assisted millimeter-wave (mmWave) massive multiple input multiple output (MIMO) system with transmit antenna selection (TAS) using orthogonal space-time block codes (OSTBC) scheme is proposed in this paper. This system combines TAS and IRS with hybrid analog-digital beamforming (HBF) for 60 GHz mmWave communications in order to exploit the benefits of TAS, OSTBC, analog beamforming (ABF), and transmit digital precoding techniques. The proposed system, however, benefits from the transmit diversity gain of OSTBC scheme as well as from the signal-to-noise r…
We consider an Intelligent Reflecting Surface (IRS)-aided multiple-input single-output (MISO) system for downlink transmission. We compare the performance of Deep Reinforcement Learning (DRL) and conventional optimization methods in finding optimal phase shifts of the IRS elements to maximize the user signal-to-noise (SNR) ratio. Furthermore, we evaluate the robustness of these methods to channel impairments and changes in the system. We demonstrate numerically that DRL solutions show more robustness to noisy channels and user mobility.
This paper studies an intelligent reflecting surface (IRS)-aided multiple-input-multiple-output (MIMO) full-duplex (FD) wireless-powered communication network (WPCN), where a hybrid access point (HAP) operating in FD broadcasts energy signals to multiple devices for their energy harvesting (EH) in the downlink (DL) and meanwhile receives information signals from devices in the uplink (UL) with the help of an IRS. Taking into account the practical finite self-interference (SI) and the non-linear EH model, we formulate the weighted sum throughput maximization optimization problem by jointly opti…
Intelligent reflecting surface (IRS) technology has recently attracted a significant interest in non-light-of-sight radar remote sensing. Prior works have largely focused on designing single IRS beamformers for this problem. For the first time in the literature, this paper considers multi-IRS-aided multiple-input multiple-output (MIMO) radar and jointly designs the transmit unimodular waveforms and optimal IRS beamformers. To this end, we derive the Cramer-Rao lower bound (CRLB) of target direction-of-arrival (DoA) as a performance metric. Unimodular transmit sequences are the preferred wavefo…
In this letter, we study the wireless point-to-point communication from a transmitter (Tx) to a receiver (Rx), which is jointly aided by an active intelligent reflecting surface (AIRS) and a passive IRS (PIRS). We consider two practical transmission schemes by deploying the two IRSs in different orders, namely, Tx$\rightarrow$PIRS$\rightarrow$AIRS$\rightarrow$Rx (TPAR) and Tx$\rightarrow$AIRS$\rightarrow$PIRS$\rightarrow$Rx (TAPR). Assuming line-of-sight channels, we derive the achievable rates for the two schemes by optimizing the placement of the AIRS with the location of the PIRS fixed. Our…
We propose a novel design of a dual-function radar communication (DFRC) system aided by an Intelligent Reflecting Surface (IRS). We consider a scenario with one target and multiple communication receivers, where there is no line-of-sight between the radar and the target. The radar precoding matrix and the IRS weights are optimally designed to maximize the weighted sum of the signal-to-noise ratio (SNR) at the radar receiver and the SNR at the communication receivers subject to power constraints and constant modulus constraints on the IRS weights. The problem is decoupled into two sub-problems,…
We consider an intelligent reflecting surface (IRS)-aided mobile edge computing (MEC) system, where an IRS is deployed to assist computation offloading from two users to an access point connected with an edge cloud. For the IRS-aided data transmission, in contrast to the conventional non-orthogonal multiple-access (NOMA) and time-division multiple-access (TDMA), we propose a new flexible time-sharing NOMA scheme that allows users to flexibly divide their data into two parts transmitted via NOMA and TDMA, respectively, thus encapsulating both conventional NOMA and TDMA as special cases. We form…
This work examines the performance gain achieved by deploying an intelligent reflecting surface (IRS) in covert communications. To this end, we formulate the joint design of the transmit power and the IRS reflection coefficients by taking into account the communication covertness for the cases with global channel state information (CSI) and without a warden's instantaneous CSI. For the case of global CSI, we first prove that perfect covertness is achievable with the aid of the IRS even for a single-antenna transmitter, which is impossible without an IRS. Then, we develop a penalty successive c…
In this paper, an intelligent reflecting surface (IRS)-aided two-way decode-and-forward (DF) relay wireless network is considered, where two users exchange information via IRS and DF relay. To enhance the sum rate performance, three power allocation (PA) strategies are proposed. Firstly, a method of maximizing sum rate (Max-SR) is proposed to jointly optimize the PA factors of user U1, user U2 and relay station (RS). To further improve the sum rate performance, two high-performance schemes, namely maximizing minimum sum rate (Max-Min-SR) and maximizing sum rate with rate constraint (Max-SR-RC)…
This paper investigates an intelligent reflecting surface (IRS)-aided multi-cell multiple-input single-output (MISO) system consisting of several multi-antenna base stations (BSs) each communicating with a single-antenna user, in which an IRS is dedicatedly deployed for assisting the wireless transmission and suppressing the inter-cell interference. Under this setup, we jointly optimize the coordinated transmit beamforming at the BSs and the reflective beamforming at the IRS, for the purpose of maximizing the minimum weighted received signal-to-interference-plus-noise ratio (SINR) at users, su…
Intelligent reflecting surface (IRS) and device-to-device (D2D) communication are two promising technologies for improving transmission reliability between transceivers in communication systems. In this paper, we consider the design of reliable communication between the access point (AP) and actuators for a downlink multiuser multiple-input single-output (MISO) system in the industrial IoT (IIoT) scenario. We propose a two-stage protocol combining IRS with D2D communication so that all actuators can successfully receive the message from AP within a given delay. The superiority of the protocol …
Intelligent reflecting surface (IRS) has emerged as a promising paradigm to improve the capacity and reliability of a wireless communication system by smartly reconfiguring the wireless propagation environment. To achieve the promising gains of IRS, the acquisition of the channel state information (CSI) is essential, which however is practically difficult since the IRS does not employ any transmit/receive radio frequency (RF) chains in general and it has limited signal processing capability. In this paper, we study the uplink channel estimation problem for an IRS-aided multiuser single-input m…
Intelligent reflecting surface (IRS) is a promising technology to extend the wireless signal coverage and support the high performance communication. By intelligently adjusting the reflection coefficients of a large number of passive reflecting elements, the IRS can modify the wireless propagation environment in favour of signal transmission. Different from most of the prior works which did not consider any cooperation between IRSs, in this work we propose and study a cooperative double-IRS aided multiple-input multiple-output (MIMO) communication system under the line-of-sight (LoS) propagati…
