Results of a three-dimensional, flux-driven, electrostatic, global, two-fluid turbulence simulation for a 5-field period stellarator with an island divertor are presented. The numerical simulation is carried out with the GBS code, recently extended to simulate plasma turbulence in non-axisymmetric magnetic equilibria. The vacuum magnetic field used in the simulation is generated with the theory of Dommaschk potentials, and describes a configuration with a central region of nested flux surfaces, surrounded by a chain of magnetic islands, similarly to the diverted configurations of W7-X. The heat outflowing from the core reaches the island region and is transported along the magnetic islands, striking the vessel walls, which correspond to the boundary of the simulation domain.
The radial transport of particles and heat is found to be mainly driven by a field-aligned coherent mode with poloidal number $m=4$. The analysis of this mode, based on non-local linear theory considerations, shows its ballooning nature. In contrast to tokamak simulations and experiments, where blobs often contribute to transport, we do not observe the presence of intermittent transport events.
The design of any large stellarator requires a plan for the removal of the particles and heat that are exhausted across the plasma edge. This is called the divertor problem, for the particle exhaust must be diverted into pumping chambers. Although the physics of diverted plasmas has many subtleties, the magnetic field configuration between the plasma edge and the surrounding chamber walls is the foundation upon which divertor design is based. The properties of this magnetic configuration has both practical constraints and mathematical constraints from magnetic field lines obeying a 1~1/2 degre…
Non-resonant stellarator divertors have magnetic flux tubes, called magnetic turnstiles, that cross cantori, which are fractal remnants of destroyed invariant tori with holes, that lie outside the outermost confining surface. The exiting and entering flux tubes can be adjacent as is generally expected but can also have the unexpected feature of entering or exiting at separate locations of the cantori. Not only can there be two types of turnstiles, but pseudo turnstiles can also exist. A pseudo turnstile is formed when a cantorus has a sufficiently large, although limited, radial excursion to s…
An efficient numerical method of studying nonresonant stellarator divertors was introduced in Boozer and Punjabi [Phys. Plasmas 25, 092505 (2018)]. This method is used in this paper to study a different magnetic field model of a nonresonant divertor. The most novel and interesting finding of this study is that diffusive magnetic field lines can be distinguished from lines that exit through the primary and the secondary turnstile, and that below some diffusive velocity, all lines exit through only the primary turnstile. The footprints of each family are stellarator symmetric and have a fixed lo…
Initial evaluation of miniature ultra-high-field commercial stellarator reactors with breeding external to resistive coils
Laboratorio Nacional de Fusión, CIEMAT（国家聚变实验室，CIEMAT）；Departamento de Física, Universidad Carlos III de Madrid（马德里卡洛斯三世大学物理系）；Oak Ridge National Laboratory (ORNL)（橡树岭国家实验室）；University of Texas, Austin（德克萨斯大学奥斯汀分校）
We present the first single-stage optimization of islands in finite-$β$ stellarator equilibria. Stellarator optimization is traditionally performed as a two-stage process; in the first stage, an optimal equilibrium is calculated which balances a set of competing constraints, and in the second stage a set of coils is found that supports said equilibrium. Stage one is generally performed using a representation for the equilibrium that assumes nestedness of flux surfaces, even though this is not warranted and occasionally undesired. The second stage optimization of coils is never perfect, and the…
The formation of the radial electric field, $E_{\rm r}$ in the SOL has been experimentally studied for attached divertor conditions in stellarator W7-X. The main objective of this study is to test the validity in a complex 3D island divertor of simple models, typically developed in tokamaks, relating $E_{\rm r}$ to the sheath potential drop gradient at the target. Additionally, we investigate the effect of the edge $E_{\rm r}$ shear on the reduction of density fluctuation amplitude, a well-established phenomenon according to the existing bibliography. The main diagnostic for measurements in th…
General formula describing both the divertor strike point splitting and width of magnetic islands created by resonant magnetic perturbations (RMPs) in a poloidally diverted tokamak equilibrium is derived. Under the assumption that the RMP is produced by coils at the low-field side such as those used to control edge localized modes (ELMs) it is demonstrated that the width of islands on different magnetic surfaces at the edge and the amount of divertor splitting are related to each other. Explanation is provided of aligned maxima of the perturbation spectra with the safety factor profile - an ef…
We present recent highlights from the most recent operation phases of Wendelstein 7-X, the most advanced stellarator in the world. Stable detachment with good particle exhaust, low impurity content, and energy confinement times exceeding 100 ms, have been maintained for tens of seconds. Pellet fueling allows for plasma phases with reduced ITG turbulence, and during such phases, the overall confinement is so good (energy confinement times often exceeding 200 ms) that the attained density and temperature profiles would not have been possible in less optimized devices, since they would have had n…
Reciprocating probes are a classic and widespread tool for the investigation of the edge and Scrape-Off Layer of magnetic fusion plasmas. In the Wendelstein 7-X (W7-X) stellarator, the Multi-Purpose Manipulator serves as a multi-user platform for probe measurements of various kinds. This paper presents a review on reciprocating probe operation during the first operation phase of W7-X with a test divertor (2017-2018). It gives an overview of the diverse zoo of probe heads and presents lessons learned about probe operation in complex magnetic geometries, operation safety, and probe head design. …
A method is demonstrated to optimize a stellarator's geometry to eliminate magnetic islands and achieve other desired physics properties at the same time. For many physics quantities that have been used in stellarator optimization, including quasisymmetry, neoclassical transport, and magnetohydrodynamic stability, it is convenient to use a magnetic equilibrium representation that assures the existence of magnetic surfaces. However, this representation hides the possible presence of magnetic islands, which are typically undesirable. To include both surface-based objectives and island widths in …
Compact quasiaxisymmetric stellarators, a near axisymmetric theory
Princeton University（普林斯顿大学）；University of Wisconsin-Madison（威斯康星大学麦迪逊分校）；Max Plank Institute for Plasma Physics（马克斯·普朗克等离子体物理研究所）；Rudolf Peierls Centre for Theoretical Physics, Parks Road, Oxford, OX1 3PU, UK（牛津大学鲁道夫·皮尔斯理论物理中心）
Princeton University（普林斯顿大学）；Max Planck Institute for Plasma Physics（马普等离子体物理研究所）；Institute for Research in Electronics and Applied Physics, University of Maryland（马里兰大学电子与应用物理研究所）；Thea Energy（Thea能源公司）；Princeton Plasma Physics Laboratory（普林斯顿等离子体物理实验室）
Good magnetic surfaces, as opposed to magnetic islands and chaotic field lines, are generally desirable for stellarators. In previous work, M. Landreman et al. [Phys. of Plasmas 28, 092505 (2021)] showed that equilibria computed by the Stepped-Pressure Equilibrium Code (SPEC) [S. P. Hudson et al., Phys. Plasmas 19, 112502 (2012)] could be optimized for good magnetic surfaces in vacuum. In this paper, we build upon their work to show the first finite-$β$, fixed- and free-boundary optimization of SPEC equilibria for good magnetic surfaces. The objective function is constructed with the Greene's …
Error fields are predominantly attributed to inevitable coil imperfections. Controlling error fields during coil fabrication and assembly is crucial for stellarators. Excessively tight coil tolerance increases time and cost, and, in part, led to the cancellation of NCSX and delay of W7-X. In this paper, we improve the recently proposed Hessian matrix method to rapidly identify important coil deviations. Two of the most common figures of merit, magnetic island size and quasi-symmetry, are analytically differentiated over coil parameters. By extracting the eigenvectors of the Hessian matrix, we …
An adjoint method to calculate the gradient of island width in stellarators is presented and applied to a set of magnetic field configurations. The underlying method of calculation of the island width is that of Cary & Hanson (1991) (with a minor modification), and requires that the residue of the island centre be small. Therefore, the gradient of the residue is calculated in addition. Both the island width and the gradient calculations are verified using an analytical magnetic field configuration introduced in Reiman & Greenside (1986). The method is also applied to the calculation of the sha…
Stellarator News, an international journal of the stellarator community, is Published by Fusion Energy Division, Oak Ridge National Laboratory, James A. Rome, Editor In the March 1995 issue . . . **** Exerpts from the U.S. Congress Office of Technology Assment report on TPX and Alternate Concepts. **** Edge transport and turbulence studies on U-3M The turbulent-driven particle flow is shown to be comparable with the equilibrium flow at the boundary of the configuration under Alfven-heating conditions in the U-3M torsatron. **** Topological aspects of island divertor studies on W7-AS The struct…
This work addresses the question of the relation between strike-point splitting and magnetic stochasticity at the edge of a poloidally diverted tokamak in the presence of externally imposed magnetic perturbations. More specifically, ad-hoc helical current sheets are introduced in order to mimic a hypothetical screening of the external resonant magnetic perturbations by the plasma. These current sheets, which suppress magnetic islands, are found to reduce the amount of splitting expected at the target, which suggests that screening effects should be observable experimentally. Multiple screening…
Harnessing Toroidal Neutral Flows to Enhance Divertor Particle Exhaust
Gauss Fusion GmbH（高斯聚变有限公司）；Oak Ridge National Laboratory（橡树岭国家实验室）；United Kingdom Atomic Energy Authority（英国原子能管理局）；University of York（约克大学）；RI Research Instruments GmbH（RI研究仪器有限公司）
Single Helical Axis (SHAx) states obtained in high current reversed field pinch (RFP) plasmas display, aside from a dominant mode in the m=1 spectrum, also a dominant m=0 mode, with the same toroidal mode number as the m=1 one. The two modes have a fixed phase relationship. The island chain created by the m=0 mode across the reversal surface gives rise, at shallow reversal of the toroidal field, to an X-point structure which separates the last closed flux surface from the first wall, creating a divertor-like configuration. The plasma-wall interaction is found to be related to the connection le…
The core collapse events observed in a stellarator experiment are studied by a three-dimensional nonlinear MHD simulations. In the low magnetic shear configuration like the Wendelstein 7-X, the rotational transform profile is very sensitive to the toroidal current density. The 3D equilibrium with localized toroidal current density is studied. If the toroidal current density follows locally in the middle of the plasma minor radius, the rotational transform is also changed locally. Sometimes, the magnetic topology changes due to appearing the magnetic island. The nonlinear behaviors of the MHD i…
We analyze a Hamiltonian model with five wire loops that delineates the magnetic surfaces of the tokamak ITER, including a similar safety factor profile and the X-point related to the presence of a poloidal divertor. Non-axisymmetric magnetic perturbations are added by external coils, similar to the correction coils installed at the tokamak DIII-D and those that will be installed at ITER. To show the influence of magnetic perturbations on the field line escape, we integrate numerically the field line differential equations and obtain the footprints and deposition patterns on the divertor plate…
The shear Alfvén continuum spectrum is studied for a tokamak with a single island chain using the ideal Magnetohydrodynamics (MHD) theory. We have taken into account the toroidal geometry and toroidal mode coupling with the island considered as a highly-shaped stellarator. Various new frequency gaps open up inside the island due to its asymmetry both poloidally and toroidally, such as the Mirror-induced Alfvén Eigenmode (MAE) gap and the Helicity-induced Alfvén Eigenmode (HAE) gap. We have shown that the MAE gap acts as the continuation of the outside Toroidal Alfvén Eigenmode (TAE) gap into t…
We present simulated figures of the diverted magnetic field lines of the tokamak ITER, obtained by numerically integrating a Hamiltonian model with electrical currents in five wire loops and control coils. We show evidences of a sticky island embedded in the chaotic region near the divertor plates, which traps magnetic field lines for many toroidal turns increasing their connection lengths to these plates.
Long pulse operation of present and future magnetic fusion devices requires sophisticated methods for protection of plasma facing components from overheating. Typically, thermographic systems are being used to fulfill this task. Steady state operation requires, however, autonomous operation of the system and fully automatic detection of abnormal events. At Wendelstein 7-X (W7-X), a large advanced stellarator, which aims at demonstrating the capabilities of the stellarator line as a future fusion power plant, significant efforts are being undertaken to develop a fully automatic system based on …
This work explores the relation between magnetic islands, long range temporal correlations and heat transport. A low order rational surface ($ι/2π= 3/2$) was purposely scanned outward through an Electron Cyclotron Resonance Heated (ECRH) plasma in the TJ-II stellarator. Density turbulence and the poloidal flow velocity (or radial electric field) were characterized using a two channel Doppler Reflectometer. Simultaneously, the ECRH power was modulated to characterize heat transport, using measurements from a 12 channel Electron Cyclotron Emission diagnostic. A systematic variation of the poloid…
Impurities cause radiation losses and plasma dilution, and in stellarator plasmas the neoclassical ambipolar radial electric field is often unfavorable for avoiding strong impurity peaking. In this work we use a new continuum drift-kinetic solver, the SFINCS code (the Stellarator Fokker-Planck Iterative Neoclassical Conservative Solver) [M. Landreman et al., Phys. Plasmas 21 (2014) 042503] which employs the full linearized Fokker-Planck-Landau operator, to calculate neoclassical impurity transport coefficients for a Wendelstein 7-X (W7-X) magnetic configuration. We compare SFINCS calculations …
Identification of MHD equilibrium $β$ limits for CFQS plasmas
Huazhong University of Science and Technology（华中科技大学）；University of Wisconsin-Madison（威斯康星大学麦迪逊分校）；Southwest Jiaotong University（西南交通大学）；Hiroshima University（广岛大学）
Given the large anisotropy of transport processes in magnetized plasmas, the magnetic field structure can strongly impact heat diffusion: magnetic surfaces and cantori form barriers to transport while chaotic layers and island structures can degrade confinement. When a small but non-zero amount of perpendicular diffusion is included, the structure of the magnetic field becomes less important, allowing pressure gradients to be supported across chaotic regions and island chains. We introduce a metric for the effective volume over which the local parallel diffusion dominates based on the solution…
We present that a statistical method known as the Complexity-Entropy analysis is useful to characterize a state of plasma turbulence and flux in the resonant magnetic perturbation (RMP) edge localized mode (ELM) control experiment. The RMP ELM suppression phase with the stochastic pedestal top temperature fluctuation can be distinguished from the natural ELM free phase with the chaotic fluctuation. It is discussed that the stochastic temperature fluctuation localized near the pedestal top can be originated from the narrow layer of the field penetration near the pedestal top. The forced magneti…
MRX: A differentiable 3D MHD equilibrium solver without nested flux surfaces
Courant Institute of Mathematical Sciences, New York University（纽约大学柯朗数学科学研究所）；William E. Boeing Department of Aeronautics and Astronautics, University of Washington（华盛顿大学威廉E.波音航空航天系）
