Form factor can be engineered in photonic cavities such that it dramatically increases the scan speed of axion haloscope detectors. Using higher-order modes of a photonic cavity, we can probe axions at larger mass ranges beyond the reach of current detectors that rely on conventional copper cavities. The main idea is to produce a higher-order mode with longitudinal field distribution that has relatively high amplitude away from both the cavity axis and the cavity walls such that it results in a relatively large form factor and maintains a high-quality factor. The detector scan speed significantly increases as it is proportional to the square of the form factor multiplied by the quality factor.
Axion haloscope detectors use microwave cavities permeated by a magnetic field to resonate photons that are converted from axions due to the inverse Primakoff effect. The sensitivity of a detector is proportional to the form factor of the cavity's search mode. Transverse symmetry breaking is used to tune the search modes for scanning across a range of axion masses. However, numerical analysis shows transverse and longitudinal symmetry breaking reduce the sensitivity of the search mode. Simulations also show longitudinal symmetry breaking leads to other undesired consequences like mode mixing a…
In an effort to extend the usefulness of microwave cavity detectors to higher axion masses, above ~8 $μ$eV (~2 GHz), a numerical trade study of cavities was conducted to investigate the merit of using variable periodic post arrays and regulating vane designs for higher-frequency searches. The results show that both designs could be used to develop resonant cavities for high-mass axion searches. Multiple configurations of both methods obtained the scanning sensitivity equivalent to approximately 4 coherently coupled cavities with a single tuning rod.
The scan rate of an axion haloscope is proportional to the square of the cavity volume. In this paper, a new class of thin-shell cavities are proposed to search for axionic dark matter. These cavities feature active volume much larger (>20X) than that of a conventional cylindrical haloscope, comparable quality factor Q, and a similar frequency tuning range. Full 3D numerical finite-element analyses have been used to show that the TM_010 eigenmodes are singly polarized throughout the volume of the cavity and can facilitate axion-photon conversion in uniform magnetic field produced by a supercon…
Axion-like particles are a broad class of dark matter candidates which are expected to behave as a coherent, classical field with a weak coupling to photons. Research into the detectability of these particles with laser interferometers has recently revealed a number of promising experimental designs. Inspired by these ideas, we propose the Axion Detection with Birefringent Cavities (ADBC) experiment, a new axion interferometry concept using a cavity that exhibits birefringence between its two, linearly polarized laser eigenmodes. This experimental concept overcomes several limitations of the d…
Conventional axion dark matter search experiments employ cylindrical microwave cavities immersed in a solenoidal magnetic field. Exploring higher frequency regions requires smaller size cavities as the TM010 resonant frequencies scale inversely with cavity radius. One intuitive way to make efficient use of a given magnet volume, and thereby to increase the experimental sensitivity, is to bundle multiple cavities together and combine their individual outputs ensuring phase-matching of the coherent axion signal. We perform an extensive study for realistic design of a phase-matching mechanism for…
In an earlier paper, a new class of thin-shell cavities were proposed to evade the steep frequency scaling of conventional axion haloscopes. In this follow-up work, we see that a generalized conic geometry enables robust frequency-tuning for these large-volume cm-wave cavities. The frequency-defining dimension of a conic shell-cavity changes symmetrically and uniformly during tuning, maintaining a high axion coupling efficiency (the form factor) to an external solenoid field. It is further shown that such tunable geometry is not restricted to circular cones. A general prescription for arbitrar…
Many searches for axion cold dark matter rely on the use of tunable electromagnetic resonators. Current detectors operate at or near microwave frequencies and use cylindrical cavities with cylindrical tuning rods. The cavity performance strongly impacts the signal power of the detector, which is expected to be very small even under optimal conditions. There is strong motivation to characterize these microwave cavities and improve their performance in order to maximize the achievable signal power. We present the results of a study characterizing the HAYSTAC (Haloscope At Yale Sensitive to Axion…
Axion haloscope detectors require high-$Q$ cavities with tunable TM$_{010}$ modes whose resonant electric field occupies as much of the full volume of the cavity as possible. An analytical study of the effects of longitudinal symmetry breaking within microwave cavities was conducted to better understand the mode structure. The study revealed longitudinal symmetry breaking of the cavities was the mechanism for avoided mode crossings (AMC) in cylindrical microwave cavities. The results showed the size of the gaps in the search frequency spectrum due to an AMC was roughly proportional to the magn…
The Relic Axion Detector Experimental Setup (RADES) is an axion search project that uses a microwave filter as resonator for Dark Matter conversion. The main focus of this publication is the description of the 3 different cavity prototypes of RADES. The result of the first tests of one of the prototypes is also presented. The filters consist of 5 or 6 stainless steel sub-cavities joined by rectangular irises. The size of the sub-cavities determines the working frequency, the amount of sub-cavities determine the working volume. The first cavity prototype was built in 2017 to work at a frequency…
Axions are a popular dark matter candidate which are often searched for in experiments known as ``haloscopes" which exploit a putative axion-photon coupling. These experiments typically rely on Transverse Magnetic (TM) modes in resonant cavities to capture and detect photons generated via axion conversion. We present a study of a resonant cavity design for application in haloscope searches, of particular use in the push to higher mass axion searches (above $\sim$60$\,μ$eV). In particular, we take advantage of azimuthally varying TM$_{m10}$ modes which, whilst typically insensitive to axions du…
In halo dark matter axion search experiments, cylindrical microwave cavities are typically employed to detect signals from the axion-photon conversion. To enhance the conversion power and reduce the noise level, cavities are placed in strong solenoid magnetic fields at sufficiently low temperatures. Exploring high mass regions in cavity-based axion search experiments requires high frequency microwave cavities and thus understanding cavity properties at high frequencies in extreme conditions is deemed necessary. We present a study of the magnetoresistance of copper using a cavity with a resonan…
We report on the design and results of the GammeV search for axion-like particles and for chameleon particles. We also discuss plans for an improved experiment to search for chameleon particles, one which is sensitive to both cosmological and power-law chameleon models. Plans for an improved axion-like particle search using coupled resonant cavities are also presented. This experiment will be more sensitive to axion-like particles than stellar astrophysical models or current helioscope experiments.
The frequency band 1-15 GHz provides exciting prospects for resonant axion haloscopes as indicated by cosmological and astrophysical arguments. Among the challenges currently addressed to reach the required sensitivity, the development of high quality factor cavities that tolerate multi-Tesla fields plays a central role. We report a 3D resonator based on a right circular copper cavity with hollow cylinders that confine higher order modes around the cylinder axis. Its effective volume at 10.3\,GHz is $3.4 \cdot 10^{-2}$ liters, and under an 8\,T-field we measured an internal quality factor of m…
Using microwave cavities one can build a resonant ``light-shining-through-walls'' experiment to search for hidden sector photons and axion like particles, predicted in many extensions of the standard model. In this note we make a feasibility study of the sensitivities which can be reached using state of the art technology.
We propose an experiment to search for axions and axion-like-particles in the galactic halo using quantum-enhanced interferometry. This proposal is related to the previously reported ideas (Phys. Rev. D 98, 035021, Phys. Rev. Lett. 121, 161301, Phys. Rev. D 100, 023548) but searches for axions in the mass range from $10^{-16}$ eV up to $10^{-8}$ eV using two coupled optical cavities. We also show how to apply squeezed states of light to enhance the sensitivity of the experiment similar to the gravitational-wave detectors. The proposed experiment has a potential to be further scaled up to a mul…
The present state of the art axion haloscope employs a cylindrical resonant cavity in a solenoidal field. We, the Center for Axion and Precision Physics Research (CAPP) of the Institute for Basic Science (IBS) in Korea, are also pursuing halo axion discovery using this cylindrical geometry. However, the presence of end caps of cavities increases challenges as we explore higher frequency regions for the axion at above 2 GHz. To overcome these challenges we exploit a toroidal design of cavity and magnetic field. A toroidal geometry offers several advantages, two of which are a larger volume for …
To account for the dark matter content in our Universe, post-inflationary scenarios predict for the QCD axion a mass in the range $(10-10^3)\,μ\mbox{eV}$. Searches with haloscope experiments in this mass range require the monitoring of resonant cavity modes with frequency above 5\,GHz, where several experimental limitations occur due to linear amplifiers, small volumes, and low quality factors of Cu resonant cavities. In this paper we deal with the last issue, presenting the result of a search for galactic axions using a haloscope based on a $36\,\mbox{cm}^3$ NbTi superconducting cavity. The c…
In this work we consider searches for dark matter made of axions or axion-like particles (ALPs) using resonant radio frequency cavities inserted into dipole magnets from particle accelerators, wiggler magnets developed for accelerator based advanced light sources, and toroidal magnets similar to those used in particle physics detectors. We investigate the expected sensitivity of such ALP dark matter detectors and discuss the engineering aspects of building and tuning them. Brief mention is also made of even stronger field magnets that are becoming available due to improvements in magnetic tech…
Resonant feedback circuits are proposed as an alternative to normal modes of conducting wall cavities or lumped circuits in searches for hidden sector particles. The proposed method offers several potential advantages over the most sensitive axion searches to date, that employ cavity resonators, including coverage of a wider range of axion masses, the ability to probe many axion masses simultaneously, and the elimination of experimentally troublesome mechanical tuning rod mechanisms. After an outline of the proposed method, we present a noise budget for a straw-man experiment configuration. We…
Searches for dark matter axion involve the use of microwave resonant cavities operating in a strong magnetic field. Detector sensitivity is directly related to the cavity quality factor, which is limited, however, by the presence of the external magnetic field. In this paper we present a cavity of novel design whose quality factor is not affected by a magnetic field. It is based on a photonic structure by the use of sapphire rods. The quality factor at cryogenic temperature is in excess of $5 \times 10^5$ for a selected mode.
The axion is a light pseudoscalar particle which suppresses CP-violating effects in strong interactions and also happens to be an excellent dark matter candidate. Axions constituting the dark matter halo of our galaxy may be detected by their resonant conversion to photons in a microwave cavity permeated by a magnetic field. The current generation of the microwave cavity experiment has demonstrated sensitivity to plausible axion models, and upgrades in progress should achieve the sensitivity required for a definitive search, at least for low mass axions. However, a comprehensive strategy for s…
Microwave cavities for a Sikivie-type axion search are subject to several constraints. In the fabrication and operation of such cavities, often used at frequencies where the resonator is highly overmoded, it is important to be able to reliably identify several properties of the cavity. Those include identifying the symmetry of the mode of interest, confirming its form factor, and determining the frequency ranges where mode crossings with intruder levels cause unacceptable admixture, thus leading to the loss of purity of the mode of interest. A simple and powerful diagnostic for mapping out the…
Analogous to the light-shining-through-wall setup proposed for axion-like particle searches, a pair of resonant cavities have been considered to search for an extra U(1) massive gauge boson, called a hidden photon, which mediates the interactions in the hidden sector. We propose a new cavity configuration, consisting of a cylindrical emitter surrounded by a hollow cylindrical detector to remarkably improve experimental sensitivity to hidden photon signals in the $μ$eV mass range. An extensive study was conducted to find the optimal cavity geometry and resonant mode, which yields the best perfo…
The axion is a hypothetical particle considered to be the most economical solution to the strong CP problem. It can also be formulated as a compelling component of dark matter. The haloscope, a leading axion detection scheme, relies on the conversion of galactic halo axions into real photons inside a resonant cavity structure in the presence of a static magnetic field, where the generated photon frequency corresponds to the mass of the axion. For maximum sensitivity it is key that the central frequency of the cavity mode structure coincides with the frequency of the generated photon. As the ma…
We study the directional effect of the expected axion dark matter signal in a resonant cavity of an axion haloscope detector, for cavity geometries not satisfying the condition that the axion de Broglie wavelength $λ_a$ is sufficiently larger than the cavity dimensions $L$ for a fully coherent conversion, i.e. $λ_a \gtrsim 2πL$. We focus on long thin cavities immersed in dipole magnets and find, for appropriately chosen cavity lengths, an O(1) modulation of the signal with the cavity orientation with respect the momentum distribution of the relic axion background predicted by the isothermal sp…
A coupled microwave-cavity system of cylindrical TM$_{010}$ single-mode has been developed to search for dark matter axions around 10 $μ{\rm eV}$(2.4 GHz) with the Rydberg-atom cavity detector at 10 mK range temperature. One component of the coupled cavity (conversion cavity) made of oxygen-free high-conductivity copper is used to convert an axion into a single photon with the Primakoff process in the strong magnetic field, while the other component (detection cavity) made of Nb is utilized to detect the converted photons with Rydberg atoms passed through it without magnetic field. Top of the …
Axion-like particles (ALPs) with couplings to electromagnetism have long been postulated as extensions to the Standard Model. String theory predicts an "axiverse" of many light axions, some of which may make up the dark matter in the universe and/or solve the strong CP problem. We propose a new experiment using superconducting radiofrequency (SRF) cavities which is sensitive to light ALPs independent of their contribution to the cosmic dark matter density. Off-shell ALPs will source cubic nonlinearities in Maxwell's equations, such that if a SRF cavity is pumped at frequencies $ω_1$ and $ω_2$,…
A tunable photonic band gap resonator for axion dark matter searches
Wellesley College（韦尔斯利学院）；University of California, Davis（加州大学戴维斯分校）；University of California, Berkeley（加州大学伯克利分校）；Brown University（布朗大学）；Yale University（耶鲁大学）；Los Alamos National Laboratory（洛斯阿拉莫斯国家实验室）
Using eigenmode analysis and full 3D FEM modelling, we demonstrate that a closed cavity built of an array of elementary harmonic oscillators with negative mutual couplings exhibits a dispersion curve with lower order modes corresponding to higher frequencies. Such cavity arrays may help to achieve large mode volumes for boosting sensitivity of the axion searches, where the mode volume for the composed array scales proportional to the number of elements, but the frequency remains constant. The negatively coupled cavity array is demonstrated with magnetically coupling coils, where the sign of ne…
Axion is a promising candidate for ultralight dark matter which may cause a polarization rotation of laser light. Recently, a new idea of probing the axion dark matter by optical linear cavities used in the arms of gravitational wave detectors has been proposed [Phys. Rev. Lett. 123, 111301 (2019)]. In this article, a realistic scheme of the axion dark matter search with the arm cavity transmission ports is revisited. Since photons detected by the transmission ports travel in the cavity for odd-number of times, the effect of axion dark matter on their phases is not cancelled out and the sensit…
Extended High-Mass Axion Search with an Auxetically Tuned Higher-Order-Mode Cavity
Institute for Basic Science（基础科学研究院）；RIKEN Center for Quantum Computing（理化学研究所量子计算中心）；Oskar Klein Centre, Department of Physics, Stockholm University（斯德哥尔摩大学奥斯卡·克莱因物理中心）；Johannes Gutenberg-Universität Mainz（美因茨约翰内斯古腾堡大学）；Helmholtz Institute Mainz（美因茨亥姆霍兹研究所）；Department of Physics, Seoul National University（首尔大学物理系）；Department of Applied Physics, Graduate School of Engineering, The University of Tokyo（东京大学大学院工学系研究科应用物理专业）
Dark matter makes up 85% of the matter in the universe and 27% of its energy density, but we do not know what comprises dark matter. It is possible that dark matter may be composed of either axions or dark photons, both of which can be detected using an ultra-sensitive microwave cavity known as a haloscope. The haloscope employed by ADMX consists of a cylindrical cavity operating at the TM$_{010}$ mode and is sensitive to the QCD axion with masses of few $μ$eV. However, this haloscope design becomes challenging to implement for higher masses. This is because higher masses require smaller-diame…
Broad frequency tuning of a Nb$_{3}$Sn superconducting microwave cavity for dark matter searches
Dipartimento di Fisica e Astronomia（物理与天文系）；INFN, Sezione di Padova（意大利国家核物理研究所帕多瓦分部）；INFN, Laboratori Nazionali di Legnaro（意大利国家核物理研究所莱尼亚罗国家实验室）；Superconducting Quantum Materials and Systems center (SQMS), Fermi National Accelerator Laboratory（超导量子材料与系统中心（SQMS），费米国家加速器实验室）；Fermi National Accelerator Laboratory（费米国家加速器实验室）；INFN, Laboratori Nazionali di Frascati（意大利国家核物理研究所弗拉斯卡蒂国家实验室）
