Harvesting waste heat with temperatures lower than 100 oC can improve system efficiency and reduce greenhouse gas emissions, yet it has been a longstanding and challenging task. Electrochemical methods for harvesting low-grade heat have attracted research interest in recent years due to the relatively high effective temperature coefficient of the electrolytes (> 1 mV/K) compared with the thermopower of traditional thermoelectric devices. Comparing with other electrochemical devices such as temperature-variation based thermally regenerative electrochemical cycle and temperature-difference based thermogalvanic cells, the thermally regenerative flow battery (TRFB) has the advantages of providing a continuous power output, decoupling the heat source and heat sink and recuperating heat, and compatible with stacking for scaling up. However, TRFB suffers from the issue of stable operation due to the challenge of pH matching between catholyte and anolyte solutions with desirable temperature coefficients. In this work, we demonstrate a PH-neutral TRFB based on KI/KI3 and K3Fe(CN)6/K4Fe(CN)6 as the catholyte and anolyte, respectively, with a cell temperature coefficient of 1.9 mV/K and a power density of 9 uW/cm2. This work also presents a comprehensive model with a coupled analysis of mass transfer and reaction kinetics in a porous electrode that can accurately capture the flow rate dependence of power density and energy conversion efficiency. We estimate that the efficiency of the pH-neutral TRFB can reach 11% of the Carnot efficiency at the maximum power output with a temperature difference of 37 K. Via analysis, we identify that the mass transfer overpotential inside the porous electrode and the resistance of the ion exchange membrane are the two major factors limiting the efficiency and power density, pointing to directions for future improvements.
All solid state batteries are claimed to be the next-generation battery system, in view of their safety accompanied by high energy densities. A new advanced, multiscale compatible, and fully three dimensional model for solid electrolytes is presented in this note. The response of the electrolyte is profoundly studied theoretically and numerically, analyzing the equilibrium and steady state behaviors, the limiting factors, as well as the most relevant constitutive parameters according to the sensitivity analysis of the model.
Lithium-metal batteries employing concentrated glyme-based electrolytes and different cathode chemistries are herein evaluated in view of a safe use of the highly energetic alkali-metal anode. Indeed, diethylene-glycol dimethyl-ether (DEGDME) and triethylene-glycol dimethyl-ether (TREGDME) dissolving lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) and lithium nitrate (LiNO3) in concentration approaching the solvents saturation limit are used in lithium batteries employing either a conversion sulfur-tin composite (S:Sn 80:20 w/w) or a Li+ (de-)insertion LiFePO4 cathode. Cyclic voltammetry (…
Dendrite free electrodeposition of lithium metal is necessary for the adoption of high energy density rechargeable lithium metal batteries. Here, we demonstrate a new mechanism of using a liquid crystalline electrolyte to suppress dendrite growth with a lithium metal anode. A nematic liquid crystalline electrolyte modifies the kinetics of electrodeposition by introducing additional overpotential due to its bulk distortion and anchoring free energy. By extending the phase-field model, we simulate the morphological evolution of the metal anode and explore the role of bulk distortion and anchorin…
The development of silicon anodes to replace conventional graphite in efforts to increase energy densities of lithium-ion batteries has been largely impeded by poor interfacial stability against liquid electrolytes. Here, stable operation of 99.9 weight% micro-Si (uSi) anode is enabled by utilizing the interface passivating properties of sulfide based solid-electrolytes. Bulk to surface characterization, as well as quantification of interfacial components showed that such an approach eliminates continuous interfacial growth and irreversible lithium losses. In uSi || layered-oxide full cells, h…
A new class of high-performance pyrrolidinium cation based ionanofluid electrolytes with higher lithium salt concentration are developed. The electrolytes are formed by dispersing imidazolium ionic liquid functionalized TiO2 nanoparticles in low conducting, 0.6 M lithium salt doped N-alkyl-N-butylpyrrolidinium bis(trifluoromethylsulfonyl)imide (Pyr14TFSI) ionic liquid (IL) hosted electrolyte. Viscosity, ionic conductivity and thermal properties of these electrolytes are compared with well studied 0.2 M salt doped Pyr14TFSI IL-based electrolyte. The highly crystalline 0.6 M lithium salt dissolv…
Interfacial deposition stability between Li metal and a solid electrolyte (SE) is important in preventing interfacial contact loss, mechanical fracture, and dendrite growth in Li-metal solid-state batteries (SSB). In this work, we investigate the deposition and mechanical stability at the Li metal/SE interface and its consequences (such as SE fracture and contact loss). A wide range of contributing factors are investigated, such as charge and mass transfer kinetics, the plasticity of Li metal and fracture of the SE, and the applied stack pressure. We quantify the effect of the ionic conductivi…
Using a new class of (BH4)- substituted argyrodite Li6PS5Z0.83(BH4)0.17, (Z = Cl, I) solid electrolyte, Li-metal solid-state batteries operating at room temperature have been developed. The cells were made by combining the modified argyrodite with an In-Li anode and two types of cathode: an oxide, LixMO2 (M = 1/3Ni, 1/3Mn, 1/3Co; so called NMC) and a titanium disulfide, TiS2. The performance of the cells was evaluated through galvanostatic cycling and Alternating Current AC electrochemical impedance measurements. Reversible capacities were observed for both cathodes for at least tens of cycles…
Solid state batteries have emerged as a potential next-generation energy storage device due to safety and energy density advantages. Development of electrolyte is one of the most important topics in solid state batteries. Electrochemical Impedance Spectroscopy (EIS) is a popular measurement technique to obtain the conductivity and diagnose the electrolyte. Current interpretation mainly uses the semicircle part of the curves and discards other information revealed by EIS such as the slope of the curve at low frequency. What is worse, some features on the curve are not fully interpreted. To bett…
All-solid-state batteries are expected to enable batteries with high energy density with the use of lithium metal anodes. Although solid electrolytes are believed to be mechanically strong enough to prevent lithium dendrites from propagating, various reports today still show cell failure due to lithium dendritic growth at room temperature. While cell parameters such as current density, electrolyte porosity and interfacial properties have been investigated, mechanical properties of lithium metal and the role of applied stack pressure on the shorting behavior is still poorly understood. Here, we…
The penetration of dendrites in ceramic lithium conductors severely constrains the development of solid-state batteries (SSBs) while its nanoscopic origin remain unelucidated. We develop an in-situ nanoscale electrochemical characterization technique to reveal the nanoscopic lithium dendrite growth kinetics and use it as a guiding tool to unlock the design of interfaces for dendrite-proof SSBs. Using Li7La3Zr2O12 (LLZO) as a model system, in-situ nanoscopic dendrite triggering measurements, ex-situ electro-mechanical characterizations, and finite element simulations are carried out which revea…
We present a mechanistic theory for predicting void evolution in the Li metal electrode during the charge and discharge of all-solid-state battery cells. A phase field formulation is developed to model vacancy annihilation and nucleation, and to enable the tracking of the void-Li metal interface. This is coupled with a viscoplastic description of Li deformation, to capture creep effects, and a mass transfer formulation accounting for substitutional (bulk and surface) Li diffusion and current-driven flux. Moreover, we incorporate the interaction between the electrode and the solid electrolyte, …
In Li-ion batteries the electrochemical potential drives the redox reactions occurring at the interface between electrolyte and storage material, typically active particles for porous electrodes, allowing Li ions intercalation/extraction from electrodes. The limiting factor of the process is not solely related to the electrochemical affinity, but also to structural features as the morphology of the electrodes. In this note, the relevance of the electrodes architecture is investigated numerically, in terms of the electro-chemo-mechanical response of a battery cell with homogeneous electrodes an…
As one of the most promising next-generation energy storage device, lithium metal batteries have been extensively investigated. However, the poor safety issue and undesired lithium dendrites growth hinder the development of lithium metal batteries. The application of solid state electrolytes has attracted increasing attention as they can solve the safety issue and partly inhibit the growth of lithium dendrites. Polyethylene oxide (PEO)-based electrolytes are very promising due to their enhanced safety and excellent flexibility. However, PEO-based electrolytes suffer from low ionic conductivity…
All solid state Li-ion batteries employing metallic lithium as an anode offer higher energy densities while also being safer than conventional liquid electrolyte based Li-ion batteries. However, the growth of tiny filaments of lithium (dendrites) across the solid state electrolyte layer leads to premature shorting of cells and limits their practical viability. The microscopic mechanisms that lead to lithium dendrite growth in solid state cells are still unclear. Using garnet based lithium ion conductor as a model solid state electrolyte, we show that interfacial void growth during lithium diss…
Solid state battery technology has recently garnered considerable interest from companies including Toyota, BMW, Dyson, and others. The primary driver behind the commercialization of solid state batteries (SSBs) is to enable the use of lithium metal as the anode, as opposed to the currently used carbon anode, which would result in ~20% energy density improvement. However, no reported solid state battery to date meets all of the performance metrics of state of the art liquid electrolyte lithium ion batteries (LIBs) and indeed several solid state electrolyte (SSE) technologies may never reach pa…
Solid-state lithium-ion batteries (SSLIBs) are considered to be the new generation of devices for energy storage due to better performance and safety. Poly (ethylene oxide) (PEO) based material becomes one of the best candidate of solid electrolytes, while its thermal conductivity is crucial to heat dissipation inside batteries. In this work, we study the thermal conductivity of PEO by molecular dynamics simulation. By enhancing the structure order, thermal conductivity of aligned crystalline PEO is obtained as high as 60 W/m-K at room temperature, which is two orders higher than the value (0.…
This paper presents the current state of mathematical modelling of the electrochemical behaviour of lithium-ion batteries as they are charged and discharged. It reviews the models developed by Newman and co-workers, both in the cases of dilute and moderately-concentrated electrolytes and indicates the modelling assumptions required for their development. Particular attention is paid to the interface conditions imposed between the electrolyte and the active electrode material; necessary conditions are derived for one of these, the Butler-Volmer relation, in order to ensure physically realistic …
Solid-state electrolytes for Li-ion batteries are attracting growing interest as they allow building safer batteries, also using lithium metal anodes. Here we studied a compound in the lithium superionic conductor (LISICON) family, i.e. Li4-xGe1-xPxO4 (LGPO). Thin films were deposited via pulsed laser deposition and their electrical properties were compared with ceramic pellets. A detailed characterization of the micro structure shows that thin films can be deposited fully crystalline at higher temperatures but also partially amorphous at room temperature. The conductivity is not strongly infl…
