Two-dimensional transition metal dichalcogenides (TMDCs) have properties attractive for optoelectronic and quantum applications. A crucial element for devices is the metal-semiconductor interface. However, high contact resistances have hindered progress. Quantum transport studies are scant as low-quality contacts are intractable at cryogenic temperatures. Here, temperature-dependent transfer length measurements are performed on chemical vapour deposition grown single-layer and bilayer WS$_2$ devices with indium alloy contacts. The devices exhibit low contact resistances and Schottky barrier heights (\sim10 k$Ω$\si{\micro\metre} at 3 K and 1.7 meV). Efficient carrier injection enables high carrier mobilities ($\sim$190 cm$^2$V$^{-1}$s$^{-1}$) and observation of resonant tunnelling. Density functional theory calculations provide insights into quantum transport and properties of the WS$_2$-indium interface. Our results reveal significant advances towards high-performance WS$_2$ devices using indium alloy contacts.
Machine-learned potential for amorphous Indium-Tin-Oxide alloys
Center for Alloy Innovation and Design (CAID), State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University（西安交通大学合金创新与设计中心、材料力学行为国家重点实验室）
III-nitride alloys are wide band gap semiconductors with a broad range of applications in optoelectronic devices such as light emitting diodes and laser diodes. Indium gallium nitride light emitting diodes have been successfully produced over the past decade. But the progress of green emission light emitting devices has been limited by the incorporation of indium in the alloy, mainly due to phase separation. This difficulty could be addressed by studying the growth and thermodynamics of these alloys. Knowledge of thermodynamic phase stabilities and of pressure - temperature - composition phase…
We present a detailed theoretical analysis of the electronic structure of $c$-plane InGaN/GaN quantum wells with indium contents varying between 10\% and 25\%. The electronic structure of the quantum wells is treated by means of an atomistic tight-binding model, accounting for variations in strain and built-in field due to random alloy fluctuations. Our analysis reveals strong localisation effects in the hole states. These effects are found not only in the ground states, but also the excited states. We conclude that localisation effects persist to of order 100~meV into the valence band, for as…
Thin-film solar cells with CuIn$_x$Ga$_{1-x}$Se$_2$ (CIGS) absorber are still far below their efficiency limit, although lab cells reach already 19.9%. One important aspect is the homogeneity of the alloy. Large-scale simulations combining Monte Carlo and density functional calculations show that two phases coexist in thermal equilibrium below room temperature. Only at higher temperatures, CIGS becomes more and more a homogeneous alloy. A larger degree of inhomogeneity for Ga-rich CIGS persists over a wide temperature range, which may contribute to the low observed efficiency of Ga-rich CIGS s…
We demonstrate electrical spin injection into multilayer graphene (MLG) in a lateral spin valve device from a highly spin-polarized Co2FeSi (CFS) Huesler electrode. Exfoliated MLG was transferred onto pre-patterned epitaxial CFS wires grown on an Si(111) substrate by a polymer-based transfer method. This method enabled us to fabricate multiple single-crystal CFS electrodes in contact with MLG. Electrical spin injection from CFS to MLG was detected through non-local magnetoresistance (MR) measurement. A non-local spin signal of 430 ohm was observed; this is the largest value among all reported …
The eutectic Ga-In (EGaIn) alloy has low vapor pressure, low toxicity, high thermal and electrical conductivities, and thus has shown a great potential for smart material applications. For such applications, EGaIn is maintained above its melting point, below which it undergoes solidification and phase separation. A scientific understanding of the structural and compositional evolution during thermal cycling could help further assess the application range of low-melting-point fusible alloys. Here, we use an integrated suite of cryogenically-enabled advanced microscopy & microanalysis to better …
White light emitting diodes based on III-nitride InGaN/GaN quantum wells currently offer the highest overall efficiency for solid state lighting applications. Although current phosphor-converted white LEDs have high electricity-to-light conversion efficiencies, it has been recently pointed out that the full potential of solid state lighting could be exploited only by color mixing approaches without employing phosphor-based wavelength conversion. Such an approach requires direct emitting LEDs of different colors, in particular in the green/yellow range ov the visible spectrum. This range, howev…
InGaN is an ideal alloy system for optoelectronic devices due its tunable band gap. Yet high-quality InGaN requires high In concentration, which is a challenging issue that limits its use in green-light LEDs and other devices. In this paper, we investigated the surfactant effect of Sb on the In incorporation on InGaN (000-1) surface via first-principles approaches. Surface phase diagram was also constructed to determine surface structures under different growth conditions. By analyzing surface stress under different structures, we found that Sb adatom can induce tensile sites in the cation lay…
Electrical spin injection from the Heusler alloy Co_2MnGe into a p-i-n Al_0.1Ga_0.9As/GaAs light emitting diode is demonstrated. A maximum steady-state spin polarization of approximately 13% at 2 K is measured in two types of heterostructures. The injected spin polarization at 2 K is calculated to be 27% based on a calibration of the spin detector using Hanle effect measurements. Although the dependence on electrical bias conditions is qualitatively similar to Fe-based spin injection devices of the same design, the spin polarization injected from Co_2MnGe decays more rapidly with increasing te…
High performance thermoelectric materials for wide-range temperature applications still remains a challenge. In this study, we have produced high-quality homogeneous $In_{0.32}Ga_{0.68}N$ on ZnO substrates, with no phase separation at high Indium content, using metal organic chemical vapor deposition for thermoelectric applications. A record high room temperature figure of merit zT is obtained of 0.86, which is five times larger than that of SiGe, the current state of the art high temperature thermoelectric material. These materials are shown to have a nearly perfect doping concentration to ma…
A self-consistent model of bipolar charge-carrier injection and transport processes in a semiconductor/insulator/conductor system is developed which incorporates space-charge effects in the description of the injection process. The amount of charge-carriers injected is strongly determined by the energy barrier emerging at the contact, but at the same time the electrostatic potential generated by the injected charge-carriers modifies the height of this injection barrier itself. In our model, self-consistency is obtained by assuming continuity of the electric displacement and of the electrochemi…
We report the electrical injection and detection of spin polarized current in lateral ferromagnet-nonmagnet-ferromagnet spin valve devices, ferromagnet being cobalt and nonmagnet being indium (In) or indium oxide (In2O3) nanostructures. The In nanostructures were grown by depositing pure In on lithographically pre-patterned structures. In2O3 nanostructures were obtained by oxidation of In nanostructures. Spin valve devices were fabricated by depositing micro magnets over the nanostructures with connecting nonmagnetic electrodes via two steps of e-beam lithography. Clear spin switching behavior…
Liquid metals exhibit remarkable mechanical properties, in particular large surface tension and low viscosity. However, these properties are greatly affected by oxidation when exposed to air. We measure the viscosity, surface tension, and contact angle of gallium (Ga) and a eutectic gallium-indium alloy (eGaIn) while controlling such oxidation by surrounding the metal with an acid bath of variable concentration. Rheometry measurements reveal a yield stress directly attributable to an oxide skin that obscures the intrinsic behavior of the liquid metals. We demonstrate how the intrinsic viscosit…
Prediction and characterization of crystal structures of alloys are a key problem in materials research. Using high-throughput ab initio calculations we explore the low-temperature phase diagrams for the following systems: {Bi-In, Bi-Mg, Bi-Sb, In-Mg, In-Sb, and Mg-Sb}. For the experimentally observed phases in these systems we provide information about their stability at low temperatures. Keywords: Binary Alloys, Ab initio, Intermetallics, Transition Metals, Structure Prediction, Phase Stability, Magnesium, Indium, Bismuth, Antimony.
We report on electrical spin injection measurements on MWNTs . We use a ferromagnetic alloy Pd$_{1-x}$Ni$_{x}$ with x $\approx$ 0.7 which allows to obtain devices with resistances as low as 5.6 $kΩ$ at 300 $K$. The yield of device resistances below 100 $kΩ$, at 300 $K$, is around 50%. We measure at 2 $K$ a hysteretic magneto-resistance due to the magnetization reversal of the ferromagnetic leads. The relative difference between the resistance in the antiparallel (AP) orientation and the parallel (P) orientation is about 2%.
Chemically stable quantum-confined 2D metals are of interest in next-generation nanoscale quantum devices. Bottom-up design and synthesis of such metals could enable the creation of materials with tailored, on-demand, electronic and optical properties for applications that utilize tunable plasmonic coupling, optical non-linearity, epsilon-near-zero behavior, or wavelength-specific light trapping. In this work, we demonstrate that the electronic, superconducting and optical properties of air-stable two-dimensional metals can be controllably tuned by the formation of alloys. Environmentally robu…
Effect of the growth temperature and the AlN mole fraction on In incorporation and properties of quaternary III-nitride layers grown by molecular beam epitaxy
A self-consistent, mean-field model of charge-carrier injection and unipolar transport in an organic semiconductor diode is developed utilizing the effective transport energy concept and taking into account a realistic density-of-states distribution as well as the presence of trap states in an organic material. The consequences resulting from the model are discussed exemplarily on the basis of an indium tin oxide/organic semiconductor/metallic conductor structure. A comparison of the theory to experimental data of a unipolar indium tin oxide/poly-3-hexyl-thiophene/Al device is presented.
InGaN-based visible LEDs find commercial applications for solid-state lighting and displays, but lattice mismatch limits the thickness of InGaN quantum wells that can be grown on GaN with high crystalline quality. Since narrower wells operate at a higher carrier density for a given current density, they increase the fraction of carriers lost to Auger recombination and lower the efficiency. The incorporation of boron, a smaller group-III element, into InGaN alloys is a promising method to eliminate the lattice mismatch and realize high-power, high-efficiency visible LEDs with thick active regio…
Basal slip acts as a secondary deformation mode in hexagonal close-packed titanium and becomes one of the primary mechanisms in titanium alloyed with simple metals. As these solute elements also lead to a pronounced reduction of the energy of the basal stacking fault, one can hypothesize that they promote basal dissociation of dislocations which can then easily glide in the basal planes. Here, we verify the validity of this hypothesis using ab initio calculations to model the interaction of a screw dislocation with indium (In) and tin (Sn). These calculations confirm that these simple metals a…
We report on the determination of the anomalous spin Hall angle in the ferromagnetic metal alloy cobalt-iron (Co$_{25}$Fe$_{75}$, CoFe). This is accomplished by measuring the spin injection/detection efficiency in a multiterminal device with nanowires of platinum (Pt) and CoFe deposited onto the magnetic insulator yttrium iron garnet (Y$_3$Fe$_5$O$_{12}$, YIG). Applying a spin-resistor model to our multiterminal spin transport data, we determine the magnon conductivity in YIG, the spin conductance at the YIG/CoFe interface and finally the anomalous spin Hall angle of CoFe as a function of its …
Reducing critical current for spin-transfer-torque-induced magnetization reversal in CPP-GMR devices: effect of low damping and enhanced spin scattering asymmetry in $Co_2FeGa_{0.5}Ge_{0.5}$ Heusler alloy
High resolution total and indium differential atomic pair distribution functions (PDFs) for In_(0.5)Ga_(0.5)As alloys have been obtained by high energy and anomalous x-ray diffraction experiments, respectively. The first peak in the total PDF is resolved as a doublet due to the presence of two distinct bond lengths, In-As and Ga-As. The In differential PDF, which involves only atomic pairs containing In, yields chemical specific information and helps ease the structure data interpretation. Both PDFs have been fit with structure models and the way in that the underlying cubic zinc-blende lattic…
The Indium Gallium Nitride (InGaN) III-Nitride ternary alloy has the potentiality to allow achieving high efficiency solar cells through the tuning of its band gap by changing the Indium composition. It also counts among its advantages a relatively low effective mass, high carriersâ mobility, a high absorption coefficient along with good radiation tolerance.However, the main drawback of InGaN is linked to its p-type doping, which is difficult to grow in good quality and on which ohmic contacts are difficult to realize. The Schottky solar cell is a good alternative to avoid the p-type doping of…
We present a closed description of the charge carrier injection process from a conductor into an insulator. Common injection models are based on single electron descriptions, being problematic especially once the amount of charge-carriers injected is large. Accordingly, we developed a model, which incorporates space charge effects in the description of the injection process. The challenge of this task is the problem of self-consistency. The amount of charge-carriers injected per unit time strongly depends on the energy barrier emerging at the contact, while at the same time the electrostatic p…
Here, we demonstrate an approach that provides a precise control of the dimension of InAs from one-dimensional nanowires to wafer-scale free-standing two-dimensional nanosheets, which have a high degree of crystallinity and outstanding electrical and optical properties, using molecular-beam epitaxy by controlling catalyst alloy segregation. In our approach, two-dimensional InAs nanosheets can be obtained directly from one-dimensional InAs nanowires by silver-indium alloy segregation, which is much easier than all previously reported method, such as traditional buffering technique and select ar…
Utilizing a material in thermoelectric applications requires a mechanical, thermal, and lattice stability as well a high figure of merit (ZT). In this work, we present the structural, electronic, magnetic, mechanical, thermodynamic, dynamic, and thermoelectric properties of CoFeYGe (Y = Ti, Cr) quaternary Heusler compounds using the density functional theory (DFT). The calculated mechanical properties and phonon dispersions reveal that the structures of these compounds are stable. Both CoFeCrGe and CoFeTiGe compounds show a ferromagnetic and ferrimagnetic half-metallic behavior with band gaps …
Weyl semimetals are playing a major role in condensed matter physics due to exotic topological properties, and their coexistence with ferromagnetism may lead to enhanced spin-related phenomena. Here, the inverse spin Hall effect (ISHE) in the ferromagnetic Weyl-semimetal Heusler alloy Co$_2$MnGa was investigated at room temperature by means of electrical spin injection in lateral spin valve structures. Spin transport properties such as spin polarization and spin diffusion length in this material were precisely extracted in order to estimate the spin Hall angle $θ_{\textrm{SH}}$, which was foun…
Conventional 3D printings are generally time-consuming and printable metal inks are rather limited. From an alternative way, we proposed a liquid phase 3D printing for quickly making metal objects. Through introducing metal alloys whose melting point is slightly above room temperature as printing inks, several representative structures spanning from one, two and three dimension to more complex patterns were demonstrated to be quickly fabricated. Compared with the air cooling in a conventional 3D printing, the liquid-phase-manufacturing offers a much higher cooling rate and thus significantly i…
Magnesium and its alloys are intriguing as possible biodegradable biomaterials due to their unique combination of biodegradability and high specific mechanical properties. However, uncontrolled biodegradation of magnesium during implantation remains a major challenge in spite of the use of alloying and protective coatings. In this study, a hybrid composite structure of magnesium metal and a biopolymer was fabricated as an alternative approach to control the corrosion rate of magnesium. A multistep process that combines metal foam production and injection molding was developed to create a hybri…
It has been demonstrated that InSb nanoinclusions, which are formed in situ, can simultaneously improve all three individual thermoelectric properties of the n-type half Heusler compound (Ti,Zr,Hf)(Co,Ni)Sb [Xie et al., Acta Mater. 58, 4795 (2010)]. In the work presented herein, we have adopted the same approach to the p-type half Heusler compound Ti(Co,Fe)Sb. The results of resistivity, Seebeck coefficient, thermal conductivity, and Hall coefficient measurements indicate that the combined high mobility electron injection, low energy electron filtering, and boundary scattering, again, lead to …
We demonsrtate electrical spin injection and detection in $n$-type Ge ($n$-Ge) at room temperature using four-terminal nonlocal spin-valve and Hanle-effect measurements in lateral spin-valve (LSV) devices with Heusler-alloy Schottky tunnel contacts. The spin diffusion length ($λ$$_{\rm Ge}$) of the Ge layer used ($n \sim$ 1 $\times$ 10$^{19}$ cm$^{-3}$) at 296 K is estimated to be $\sim$ 0.44 $\pm$ 0.02 $μ$m. Room-temperature spin signals can be observed reproducibly at the low bias voltage range ($\le$ 0.7 V) for LSVs with relatively low resistance-area product ($RA$) values ($\le$ 1 k$Ω$$μ$m…
In this paper, we study the internal quantum efficiency and lasing threshold of AlGaN/GaN separate confinement heterostructures designed for ultraviolet laser emission. We discuss the effect of carrier localization and carrier diffusion on the optical performance. The implementation of graded index separate confinement heterostructures results in an improved carrier collection at the multi-quantum well, which facilitates population inversion and reduces the lasing threshold. However, this improvement is not correlated with the internal quantum efficiency of the spontaneous emission. We show th…
The performance of solution-processed organic light emitting diodes (OLEDs) is often limited by non-uniform contacts. In this work, we introduce Ni-containing solution-processed metal oxide (MO) interfacial layers inserted between indium tin oxide (ITO) and poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) to improve the bottom electrode contact for OLEDs using the poly(p-phenylene vinylene) (PPV) derivative Super-Yellow (SY) as an emission layer. For ITO/Ni-containing MO/PEDOT:PSS bottom electrode structures we show enhanced wetting properties that result in an improved OLE…
Using the full potential linearised augmented planewave method we study the electronic and magnetic properties of the (001) and (111) surfaces of the half-metallic Heusler alloy NiMnSb from first-principles. We take into account all possible surface terminations including relaxations of these surfaces. Special attention is paid to the spin-polarization at the Fermi level which governs the spin-injection from such a metal into a semiconductor. In general, these surfaces lose the half-metallic character of the bulk NiMnSb, but for the (111) surfaces this loss is more pronounced. Although structu…
Efficiency droop effect under high injection in GaN-based light emitting diodes (LEDs) strongly depends on wavelength, which is still not well understood. In this paper, through differential carrier lifetime measurements on commercialized near-UV, blue, and green LEDs, their different efficiency droop behaviors are attributed to different carrier lifetimes, which are prolonged as wavelength increases. This relationship between carrier lifetime and indium composition of InGaN quantum well is believed owing to the polarization-induced quantum confinement Stark effect. Long carrier lifetime not o…
A growing interest in colloidal quantum dot (QD) based light-emitting diodes (QD-LEDs) has been motivated by the exceptional color purity and spectral tunability of QD emission as well as the amenability of QD materials to highly scalable and inexpensive solution processing. One current challenge in the QD-LED field has been a still incomplete understanding of the role of extrinsic factors (e.g., recombination via QD surface defects) versus intrinsic processes such as multicarrier Auger recombination or electron-hole separation due to applied electric field in defining device efficiency. Here,…
