Broad bandwidth and stable microresonator frequency combs are critical for accurate and precise optical frequency measurements in a compact and deployable format. Typically, broad bandwidths (e.g., octave spans) are achieved by tailoring the microresonator's geometric dispersion. However, geometric dispersion engineering alone may be insufficient for sustaining bandwidths well beyond an octave. Here, we introduce the novel concept of synthetic dispersion, in which a second pump laser effectively alters the dispersion landscape to create Kerr soliton microcombs that extend far beyond the anomalous geometric dispersion region. Through detailed numerical simulations, we show that the synthetic dispersion model captures the system's key physical behavior, in which the second pump enables non-degenerate four-wave mixing that produces new dispersive waves on both sides of the spectrum. We experimentally demonstrate these concepts by pumping a silicon nitride microring resonator at 1060 nm and 1550 nm to generate a single soliton microcomb whose bandwidth approaches two octaves (137 THz to 407 THz) and whose phase coherence is verified through beat note measurements. Such ultra-broadband microcombs provide new opportunities for full microcomb stabilization in optical frequency synthesis and optical atomic clocks, while the synthetic dispersion concept can extend microcomb operation to wavelengths that are hard to reach solely through geometric dispersion engineering.
Optical frequency comb, with precisely controlled spectral lines spanning a broad range, has been the key enabling technology for many scientific breakthroughs. In addition to the traditional implementation based on modelocked lasers, photonic frequency microcombs based on dissipative Kerr and quadratic cavity solitons in high-Q microresonators have become invaluable in applications requiring compact footprint, low cost, good energy efficiency, large comb spacing, and access to nonconventional spectral regions. In this review, we comprehensively examine the recent progress of photonic frequenc…
Optical frequency combs enable state-of-the-art applications including frequency metrology, optical clocks, astronomical measurements, and sensing. Recent demonstrations of microresonator-based Kerr frequency combs or microcombs pave the way to scalable and stable comb sources on a photonic chip. Generating microcombs in the visible wavelength range, however, has been limited by large material dispersion and optical loss. Here we demonstrate a scheme for efficiently generating visible microcomb in a high Q aluminum nitride microring resonator. Enhanced Pockels effect strongly couples infrared …
Narrow linewidth lasers and optical frequency combs generated with mode-locked lasers revolutionized optical frequency metrology. The advent of soliton Kerr frequency combs in compact crystalline or integrated ring optical microresonators opens new horizons for applications. These combs, as was naturally assumed, however, require narrow-linewidth single-frequency pump lasers. We demonstrate that a regular multi-frequency Fabry-Perot laser diode self-injection locked to an optical whispering gallery mode (WGM) microresonator can be first efficiently transformed to a single-frequency ultra-narro…
Kerr soliton microcombs have recently emerged as a prominent topic in integrated photonics and enabled new horizons for optical frequency metrology. Kerr soliton microcombs, as its name suggests, are based on the high-order cubic optical nonlinearity. It is desirable to exploit quadratic photonic materials, namely Pockels materials, for soliton generation and on-chip implementation of 1f-2f comb self-referencing. Such quadratically-driven solitons have been theoretically proposed, but have not yet been observed in a nanophotonic platform despite of recent progresses in quadratic comb generatio…
We theoretically and experimentally investigate the formation of dissipative coherent structures in Kerr nonlinear optical microresonators, whose integrated dispersion exceeds the free-spectral range. We demonstrate that the presence of any periodic modulation along the resonator's circumference, such as periodically varying dispersion, can excite higher-order comb structures. We explore the outcomes of coherent microcomb generation in both cases of anomalous and normal dispersion. We are able to access this regime in microresonators via the high peak power of synchronous pulse-driving. For so…
Dissipative Kerr soliton microcomb has been recognized as a promising on-chip multi-wavelength laser source for fiber optical communications, as its comb lines possess frequency and phase stability far beyond independent lasers. In the scenarios of coherent optical transmission and interconnect, a highly beneficial but rarely explored target is to re-generate a Kerr soliton microcomb at the receiver side as local oscillators that conserve the frequency and phase property of the incoming data carriers, so that to enable coherent detection with minimized optical and electrical compensations. Her…
We demonstrate polarization multiplexed dissipative Kerr solitons in an on-chip silicon nitride micro-resonator. In our experiment, TE- and TM-polarized soliton can be individually generated and controlled, thanks to their weak mutual interaction as the result of sufficiently different repetition rates and orthogonal polarization states. Furthermore, we find that TE- and TM-polarized solitons usually exhibit uncorrelated time jitters, therefore the frequency and phase coherence between the polarization multiplexed soliton microcombs change dramatically as a function of pump laser parameters, b…
Frequency combs spanning over an octave have been successfully demonstrated in Kerr nonlinear microresonators on-chip. These micro-combs rely on both engineered dispersion, to enable generation of frequency components across the octave, and on engineered coupling, to efficiently extract the generated light into an access waveguide while maintaining a close to critically-coupled pump. The latter is challenging as the spatial overlap between the access waveguide and the ring modes decays with frequency. This leads to strong coupling variation across the octave, with poor extraction at short wave…
Laser frequency combs are coherent light sources that simultaneously provide pristine frequency spacings for precision metrology and the fundamental basis for ultrafast and attosecond sciences. Recently, nonlinear parametric conversion in high-Q microresonators has been suggested as an alternative platform for optical frequency combs, though almost all in 100 GHz frequencies or more. Here we report a low-phase-noise on-chip Kerr frequency comb with mode spacing compatible with high-speed silicon optoelectronics. The waveguide cross-section of the silicon nitride spiral resonator is designed to…
Dissipative solitons formed in Kerr microresonators may enable chip-scale frequency combs for precision optical metrology. Here we explore the creation of an octave-spanning, 15-GHz repetition-rate microcomb suitable for both f-2f self-referencing and optical-frequency comparisons across the near infrared. This is achieved through a simple and reliable approach to deterministically generate, and subsequently frequency stabilize, soliton pulse trains in a silica-disk resonator. Efficient silicon-nitride waveguides provide a supercontinuum spanning 700 to 2100 nm, enabling both offset-frequency …
In this Letter, we investigate the feasibility and performance of wavelength division multiplexed (WDM) optical communications using an integrated dissipative Kerr soliton micro-comb as the multi-channel laser source. First, we confirm that soliton microcomb pumped directly by a DFB laser self-injection locked to the host micro-cavity has sufficiently low frequency and amplitude noises to encode advanced data formats. Second, perfect soliton crystals are exploited to boost the power level of each microcomb line, so that they can be directly used for data modulation excluding pre-amplification.…
Microresonator-based optical frequency combs, or "microcombs", have attracted lots of attention in the last few years thanks to their promising applications in telecommunications, spectroscopy and optical clocks. The process of comb generation in microresonators can be modelled in the frequency domain using coupled mode equations, and has also recently been successfully described in the time domain using a nonlinear Schrödinger equation known as the Lugiato-Lefever equation. Though time-domain approaches have brought many interesting insights for the understanding of microcombs, an intuitive f…
Microresonator-based optical frequency combs emitted from high-quality-factor microresonators, also known as microcombs, have opened up new horizons to areas of optical frequency comb technology including frequency metrology, precision sensing, and optical communication. To extend the capability of microcombs for such applications, large and reliable tunability is of critical importance. Here, we show broad spectral tuning of Kerr soliton microcombs in a thermally controlled crystalline microresonator with pump-detuning stabilization. The fundamental elements composing frequency combs, namely …
By generating a Brillouin laser in an optical microresonator, we realize a soliton Kerr microcomb through exciting the Kerr frequency comb using the generated Brillouin laser in the same cavity. The intracavity Brillouin laser pumping scheme enables us to access the soliton states with a blue-detuned input pump. Due to the ultra-narrow linewidth and the low-noise properties of the generated Brillouin laser, the observed soliton microcomb exhibits narrow-linewidth comb lines and stable repetition rate even by using a diode laser with relatively broad linewidth. Also, we demonstrate a low-noise …
Advances in microresonator-based soliton generation promise chip-scale integration of optical frequency comb for applications spanning from time keeping to frequency synthesis. Miniaturized cavities harness Kerr nonlinearity and enable terahertz soliton repetition rates. However, such high repetition rates are not amenable to direct electronic detection. Here, we demonstrate hybrid Kerr and electro-optic microcombs using the lithium niobate thin film that exhibits both Kerr and Pockels nonlinearities. By interleaving the high-repetition-rate Kerr soliton comb with the low-repetition-rate elect…
Microresonator-based Kerr frequency comb (microcomb) generation can potentially revolutionize a variety of applications ranging from telecommunications to optical frequency synthesis. However, phase-locked microcombs have generally had low conversion efficiency limited to a few percent. Here we report experimental results that achieve ~30% conversion efficiency (~200 mW on-chip comb power excluding the pump) in the fiber telecommunication band with broadband mode-locked dark-pulse combs. We present a general analysis on the efficiency which is applicable to any phase-locked microcomb state. Th…
We demonstrate a photonic RF integrator based on an integrated soliton crystal microcomb source. By multicasting and progressively delaying the input RF signal using a transversal structure, the input RF signal is integrated discretely. Up to 81 wavelengths are provided by the microcomb source, which enable a large integration time window of 6.8 ns, together with a time resolution as fast as 84 ps. We perform signal integration of a diverse range of input RF signals including Gaussian pulses with varying time widths, dual pulses with varying time intervals and a square waveform. The experiment…
Unlocking the O-Band Coherent Transmission: high-power, broadband soliton microcomb
Aston University（阿斯顿大学）；Enlightra（恩莱特拉）；KDDI Research（KDDI研究院）；Lightera Laboratories（Lightera实验室）；Fraunhofer Heinrich-Hertz-Institute（弗劳恩霍夫海因里希·赫兹研究所）；The National Institute of Information and Communications Technology（信息通信研究机构）
Dissipative Kerr solitons are self-sustaining optical wavepackets in resonators. They use the Kerr nonlinearity to both compensate dispersion and to offset optical loss. Besides providing insights into nonlinear resonator physics, they can be applied in frequency metrology, precision clocks, and spectroscopy. Like other optical solitons, the dissipative Kerr soliton can radiate power in the form of a dispersive wave through a process that is the optical analogue of Cherenkov radiation. Dispersive waves typically consist of an ensemble of optical modes. A limiting case is demonstrated in which …
We demonstrate a scheme incorporating dual coupled microresonators through which mode interactions are intentionally introduced and controlled for Kerr frequency comb (microcomb) generation in the normal dispersion region. Microcomb generation, repetition rate selection, and mode locking are achieved with coupled silicon nitride microrings controlled via an on-chip microheater. Our results show for the first time that mode interactions can be programmably tuned to facilitate broadband normal-dispersion microcombs. The proposed scheme increases freedom in microresonator design and may make it p…
Microresonator-based soliton frequency combs - microcombs - have recently emerged to offer low-noise, photonic-chip sources for optical measurements. Owing to nonlinear-optical physics, microcombs can be built with various materials and tuned or stabilized with a consistent framework. Some applications require phase stabilization, including optical-frequency synthesis and measurements, optical-frequency division, and optical clocks. Partially stabilized microcombs can also benefit applications, such as oscillators, ranging, dual-comb spectroscopy, wavelength calibration, and optical communicat…
We demonstrate an RF photonic fractional Hilbert transformer based on an integrated Kerr micro-comb source featuring a record low free spectral range of 48.9 GHz, yielding 75 microcomb lines across the C-band. By programming and shaping the comb lines according to calculated tap weights, we demonstrate that the Hilbert transformer can achieve tunable bandwidths ranging from 1.2 to 15.3 GHz, switchable centre frequencies from baseband to 9.5 GHz, and arbitrary fractional orders. We experimentally characterize the RF amplitude and phase response of the tunable bandpass and lowpass Hilbert transf…
Soliton microcombs provide a versatile platform for realizing fundamental studies and technological applications. To be utilized as frequency rulers for precision metrology, soliton microcombs must display broadband phase coherence, a parameter characterized by the optical phase or frequency noise of the comb lines and their corresponding optical linewidths. Here, we analyse the optical phase-noise dynamics in soliton microcombs generated in silicon nitride high-Q microresonators and show that, because of the Raman self-frequency shift or dispersive-wave recoil, the Lorentzian linewidth of som…
A quiet point, an operating point of pump-resonance detuning that minimizes frequency fluctuation due to nonlinear effects inside a resonator, has been employed for phase noise reduction of a soliton Kerr microresonator frequency comb (microcomb). Naturally, it is expected that the use of the point will also improve performances of a microcomb in terms of frequency stability and faithfulness in a phase locked loop. In this study, we experimentally investigate the effect in a microcomb with a repetition frequency of 300~GHz. We obtain a lowest fractional frequency instability at a quiet point o…
Dissipative Kerr solitons are self-organized optical waves arising from the interplay between Kerr effect and dispersion. They can form spontaneously in nonlinear microresonators pumped with an external continuous-wave laser, which provides the parametric gain for the proliferation of an ultrastable frequency comb. These miniaturized and battery driven microcombs have become a disruptive technology for precision metrology, broadband telecommunication and ultrafast optical ranging. In this work, we report on the first experimental observation of dissipative Kerr solitons generated in a ring cav…
Microresonator frequency combs (microcombs) are enabling new applications in frequency synthesis and metrology from high-speed laser ranging to coherent optical communications. One critical parameter that dictates the performance of the microcomb is the optical quality factor (Q) of the microresonator. Microresonators fabricated in planar structures such as silicon nitride (Si3N4) allow for dispersion engineering and the possibility to monolithically integrate the microcomb with other photonic devices. However, the relatively large refractive index contrast and the tight optical confinement re…
We report a photonic radio frequency (RF) fractional differentiator based on an integrated Kerr micro-comb source. The micro-comb source has a free spectral range (FSR) of 49 GHz, generating a large number of comb lines that serve as a high-performance multi-wavelength source for the differentiator. By programming and shaping the comb lines according to calculated tap weights, arbitrary fractional orders ranging from 0.15 to 0.90 are achieved over a broad RF operation bandwidth of 15.49 GHz. We experimentally characterize the frequency-domain RF amplitude and phase responses as well as the tem…
Integrated Kerr microcombs are emerging as a powerful tool as sources of multiple wavelength channels for photonic RF and microwave signal processing mainly in the context of transversal filters. They offer a compact device footprint, very high versatility, large numbers of wavelengths, and wide Nyquist bands. Here, we review recent progress on Kerr microcomb-based photonic RF and microwave reconfigurable filters, based both on transversal filter methods and on RF to optical bandwidth scaling. We compare and contrast results achieved with wide comb spacing combs (200GHz) with more finely space…
The demand for high-speed and highly efficient optical communication techniques has been rapidly growing due to the ever-increasing volume of data traffic. As well as the digital coherent communication used for core and metro networks, intensity modulation and direct detection (IM-DD) are still promising schemes in intra/inter data centers thanks to their low latency, high reliability, and good cost performance. In this work, we study a microresonator-based frequency comb as a potential light source for future IM-DD optical systems where applications may include replacing individual stabilized…
We report a broadband radio frequency (RF) channelizer with up to 92 channels using a coherent microcomb source. A soliton crystal microcomb, generated by a 49 GHz micro-ring resonator (MRR), is used as a multi-wavelength source. Due to its ultra-low comb spacing, up to 92 wavelengths are available in the C band, yielding a broad operation bandwidth. Another high-Q MRR is employed as a passive optical periodic filter to slice the RF spectrum with a high resolution of 121.4 MHz. We experimentally achieve an instantaneous RF operation bandwidth of 8.08 GHz and verify RF channelization up to 17.5…
