The elasto-plastic material behavior, material strength and failure modes of metals fabricated by additive manufacturing technologies are significantly determined by the underlying process-specific microstructure evolution. In this work a novel physics-based and data-supported phenomenological microstructure model for Ti-6Al-4V is proposed that is suitable for the part-scale simulation of selective laser melting processes. The model predicts spatially homogenized phase fractions of the most relevant microstructural species, namely the stable $β$-phase, the stable $α_{\text{s}}$-phase as well as the metastable Martensite $α_{\text{m}}$-phase, in a physically consistent manner. In particular, the modeled microstructure evolution, in form of diffusion-based and non-diffusional transformations, is a pure consequence of energy and mobility competitions among the different species, without the need for heuristic transformation criteria as often applied in existing models. The mathematically consistent formulation of the evolution equations in rate form renders the model suitable for the practically relevant scenario of temperature- or time-dependent diffusion coefficients, arbitrary temperature profiles, and multiple coexisting phases. Due to its physically motivated foundation, the proposed model requires only a minimal number of free parameters, which are determined in an inverse identification process considering a broad experimental data basis in form of time-temperature transformation diagrams. Subsequently, the predictive ability of the model is demonstrated by means of continuous cooling transformation diagrams, showing that experimentally observed characteristics such as critical cooling rates emerge naturally from the proposed microstructure model, instead of being enforced as heuristic transformation criteria.
A Versatile SPH Modeling Framework for Coupled Microfluid-Powder Dynamics in Additive Manufacturing: Binder Jetting, Material Jetting, Directed Energy Deposition and Powder Bed Fusion
From powder to part: influence of virgin and recovered Inconel 625 powders on the DED-LP processability, microstructure and mechanical properties
Univ. Bordeaux, ESTIA Institute of Technology(波尔多大学,ESTIA理工学院);Arts et Métiers Institute of Technology, CNRS, Bordeaux INP, I2M, UMR 5295(巴黎国立高等工艺学院,法国国家科学研究中心,波尔多国立理工学院,I2M实验室)
Accurate prediction of melt pool shapes in laser powder bed fusion by the non-linear temperature equation including phase changes - isotropic versus anisotropic conductivity
在这方面的贡献,我们验证的物理模型的基础上瞬态温度方程(包括潜热)w.r.t. AMB 2018 -02是在美国国家标准与技术研究所建立的增材制造基准系列中提供的实验装置。我们的目标是预测以下感兴趣的量:宽度,深度和长度的熔池的数值模拟和报告也可获得的数值结果的冷却速率。我们首先假设激光器的双椭球形,并证明了一个良好的校准,纯热模型的基础上各向同性的热导率是能够预测所有感兴趣的数量,从实验测量值的最大偏差为7.3%。然而,有趣的是观察到,如果我们在模型中直接引入测量的激光轮廓(而不是双椭球形状),则所研究的模型返回与实验值的19.3%的偏差。这促使通过引入各向异性传导率来更新模型,该各向异性传导率旨在成为熔池内热材料对流的简化模型。这种各向异性模型能够预测上述所有感兴趣的量,与实验值的最大偏差为6.5%。我们注意到,虽然更具有预测性,但各向异性模型仅引起计算复杂性的边际增加。
Predicting Thermoelectric Power Factor of Bismuth Telluride During Laser Powder Bed Fusion Additive Manufacturing
Wright State University(莱特州立大学);Colorado School of Mines(科罗拉多矿业大学);The George Washington University(乔治·华盛顿大学);Open Additive, LLC(Open Additive 有限责任公司)
增材制造(AM)工艺,如激光粉末床熔合,允许通过分层散布和熔化粉末直到创建自由成形的零件形状来制造物体。为了提高AM工艺中所涉及的材料的性能,预测材料表征性能随加工条件的变化非常重要。在热电材料中,功率因数是衡量材料将热量转化为电能的效率的指标。虽然早期的工作已经使用各种技术预测了不同热电材料的材料表征特性,但是尚未探索在AM过程期间实施机器学习模型来预测碲化铋(Bi2Te3)的功率因数。这是重要的,因为Bi2Te3是用于低温应用的标准材料。因此,我们使用关于所涉及的制造工艺参数的数据和在Bi 2 Te 3的AM期间收集的原位传感器监测数据来训练不同的机器学习模型,以便预测其热电功率因数。我们使用80%的训练数据和20%的测试数据实施了有监督的机器学习技术,并进一步使用排列特征重要性方法来识别重要的工艺参数和最适合预测材料功率因数的原位传感器特征。基于集成的方法,如随机森林,AdaBoost分类器和装袋分类器在预测功率因数方面表现最好,其中装袋分类器模型的准确率最高,达到90%。此外,我们发现了前15个工艺参数和原位传感器特征,以表征材料的制造特性,如功率因数。这些特征可以进一步优化,以最大化热电材料的功率因数,并提高使用这种材料制造的产品的质量。