A Field-Enhanced Conduction-Cooled Superconducting Cavity for High-Repetition-Rate Ultrafast Electron Bunch Generation
Osama Mohsen, Daniel Mihalcea, Nathan Tom, Noah Adams, Ram Dhuley, Michael I Geelhoed, Aaron McKeown, Venumadhav Korampally, Philippe Piot, Iman Salehinia, Jaya… 展开作者
Osama Mohsen, Daniel Mihalcea, Nathan Tom, Noah Adams, Ram Dhuley, Michael I Geelhoed, Aaron McKeown, Venumadhav Korampally, Philippe Piot, Iman Salehinia, Jayakar C. Thangaraj, Tianzhe Xu
High-repetition-rate sources of bright electron bunches have a wide range of applications. They can directly be employed as probes in electron-scattering setups, or serve as a backbone for the generation of radiation over a broad range of the electromagnetic spectrum. This paper describes the development of a compact sub-Mega-electronvolt (sub-MeV) electron-source setup capable of operating at MHz repetition rates and forming sub-picosecond electron bunches with transverse emittance below 20~nm. The setup relies on a conduction-cooled superconducting single-cell resonator with its geometry altered to enhance the field at the surface of the emitter. The system is designed to accommodate cooling using a model a $2$~W at 4.2 K pulse tube cryogen-free cryocooler. Although we focus on the case of a photoemitted electron bunch, the scheme could be adapted to other emission mechanisms.
We present the results of multi-objective genetic algorithm optimizations of a potential single shot ultra fast electron diffraction beamline utilizing a 225 kV dc gun with a novel cryocooled photocathode system and buncher cavity. Optimizations of the transverse projected emittance as a function of bunch charge are presented and discussed in terms of the scaling laws derived in the charge saturation limit. Additionally, optimization of the transverse coherence length as a function of final rms bunch length at sample location have been performed for three different sample radii: 50, 100, 200 m…
We present a novel concept for the generation of gigahertz repetition rate high brightness electron bunches. A custom design 100 kV thermionic gun provides a continuous electron beam, with the current determined by the filament size and temperature. A 1 GHz rectangular RF cavity deflects the beam across a knife-edge, creating a pulsed beam. Adding a higher harmonic mode to this cavity results in a flattened magnetic field profile which increases the duty cycle to 30%. Finally, a compression cavity induces a negative longitudinal velocity-time chirp in a bunch, initiating ballistic compression.…
The formation of a double-horn current profile is a challenging issue in the achievement of electron bunch with high peak current, especially for high-repetition-rate X-ray free-electron lasers (XFELs) where more nonlinear and intricate beam dynamics propagation is involved. Here, we propose to correct the nonlinear beam longitudinal phase space distortion in the photoinjector section with a dual-mode buncher. In combination with the evolutionary many-objective beam dynamics optimization, this method is shown to be effective in manipulating the longitudinal phase space at the injector exit. Fu…
Using recently available GaN FETs, a 600 Volt three-stage, multi-FET switch has been developed having 2 nanosecond rise time driving a 200 Ohm load with the potential of approaching 30 MHz average switching rates. Possible applications include driving particle beam choppers kicking bunch-by-bunch and beam deflectors where the rise time needs to be custom tailored. This paper reports on the engineering issues addressed, the design approach taken and some performance results of this switch.
We present measurements of the pulse length of ultracold electron bunches generated by near-threshold two-photon photoionization of a laser-cooled gas. The pulse length has been measured using a resonant $3$ GHz deflecting cavity in TM$_{110}$ mode. We have measured the pulse length in three ionization regimes. The first is direct two-photon photoionization using only a $480$ nm femtosecond laser pulse, which results in short ($\sim 15$ ps) but hot ($\sim 10^{4}$ K) electron bunches. The second regime is just-above-threshold femtosecond photoionization employing the combination of a continuous…
We present the design of a high repetition rate MeV energy ultrafast electron diffraction instrument based on a DC photoelectron gun and an SRF linac with multiple independently controlled accelerating and bunching cavities. The design is based on the existing Cornell photoinjector, which can readily be applied to the presented findings. Using particle tracking simulations in conjunction with multiobjective genetic algorithm optimization, we explore the smallest bunch lengths, emittance, and probe spot sizes achievable. We present results for both stroboscopic conditions (with single electrons…
Studies were made into the arise and an evolution of the beam breakup (BBU) instability in a rectangular dielectric resonator under excitation by a sequence of relativistic electron bunches. The dielectric resonator is a metal rectangular waveguide $R_{26}$ $(45mm\times 90mm)$ with Teflon dielectric slabs $8.2mm$ thick (dielectric constant $\varepsilon=2.051$) located along the wide side of the resonator. The wavelength of the $LM_{21}$ operating mode having a symmetric profile of the longitudinal electric field component is $53.2mm$. The electron energy of bunches is $4.5MeV$ , the charge of …
To achieve Ampere-class electron beam accelerators the pulse delivery rate need to be much higher than the typical photo injector repetition rate of the order of a few kilohertz. We propose here an injector which can, in principle, generate electron bunches at the same rate as the operating RF frequency. A conduction-cooled superconducting radio frequency (SRF) cavity operating in the CW mode and housing a field emission element at its region of high axial electric field can be a viable method of generating high repetition-rate electron bunches. In this paper, we report the development and exp…
A train of short charged particle bunches can efficiently drive a strong plasma wakefield over a long propagation distance only if all bunches reside in focusing and decelerating phases of the wakefield. This is shown possible with equidistant bunch trains, but requires the bunch charge to increase along the train and the plasma frequency to be higher than the bunch repetition frequency.
A high-brilliance ($\sim10^{24}$~photon.s$^{-1}$.mm$^{-2}$.mrd$^{-2}$/0.1\%) gamma-ray source experiment is currently being planned at Fermilab ($E_γ\simeq 1.1$~MeV)~[1]. The source implements a high-repetition-rate inverse Compton scattering by colliding electron bunches formed in a 300-MeV superconducting linac with a high-intensity laser pulse. This paper describes the design rationale along with some of technical challenges associated to producing high-repetition-rate collision. The expected performances of the gamma-ray source are also presented.
With a low emittance and short-bunch electron beam at a high repetition rate realized by a superconducting linac, stimulated excitation of an optical cavity at the terahertz spectrum range has been shown. The electron beam passed through small holes in the cavity mirrors without being destroyed. A sharp resonance structure which indicated wide-band stimulated emission via coherent diffraction radiation was observed while scanning the round-trip length of the cavity.
We report on electron wakefield acceleration in the resonant bubble regime with few-millijoule near-single-cycle laser pulses at a kilohertz repetition rate. Using very tight focusing of the laser pulse in conjunction with microscale supersonic gas jets, we demonstrate a stable relativistic electron source with a high charge per pulse up to 24 pC/shot. The corresponding average current is 24 nA, making this kilohertz electron source useful for various applications.
Electro-optical detection has proven to be a valuable technique to study temporal profiles of THz pulses with pulse durations down to femtoseconds. As the Coulomb field around a relativistic electron bunch resembles the current profile, electro-optical detection can be exploited for non-invasive bunch length measurements at accelerators. We have developed a very compact and robust electro-optical detection system based on spectral decoding for bunch length monitoring at the European XFEL with single-shot resolution better than 200~fs. Apart from the GaP crystal and the corresponding laser opti…
Beam-driven collinear wakefield accelerators (CWAs) that operate by using slow-wave structures or plasmas hold great promise toward reducing the size of contemporary accelerators. Sustainable acceleration of charged particles to high energies in the CWA relies on using field-generating relativistic electron bunches with a highly asymmetric peak current profile and a large energy chirp. A new approach to obtaining such bunches has been proposed and illustrated with the accelerator design supported by particle tracking simulations. It has been shown that the required particle distribution in the…
Earlier, the authors found a mechanism for the sequence of short relativistic electron bunches, which leads to resonant excitation of the wakefield, even if the repetition frequency of bunches differs from the plasma frequency. In this case, the synchronization of frequencies is restored due to defocusing of the bunches which get into the bad phases with respect to the plasma wave. However, in this case, the bunches are lost, which as a result of this do not participate in the excitation of the wakefield. In this paper, numerical simulation was used to study the dynamics of electron bunches an…
Free Electron Lasers driven by Super-Conducting Linacs require the generation, acceleration and transport of trains of bunches with high charge, high repetition rate and low emittance. A numerical model already developed for the modeling of beam dynamics in SC Linacs has been now extended to treat RF guns with proper description of the photocathode bunch generation. The model algorithm is based on a coupled integration of Newton and Maxwell equations under a slowly varying envelope approximation for the time evolution of mode amplitudes in the accelerating structure and an envelope equation de…
The operation of an inverse-Compton scattering source of x-rays or gamma-rays requires the precision alignment and synchronization of highly focused electron bunches and laser pulses at the collision point. The arrival times of electron and laser pulses must be synchronized with picosecond precision. We have developed an RF synchronization technique that reduces the initial timing uncertainty from 350 ps to less than 2 ps, greatly reducing the parameter space to be optimized while commissioning the x-ray source. We describe the technique and present measurements of its performance.
The development of fast detection methods for comprehensive monitoring of electron bunches is a prerequisite to gain comprehensive control over the synchrontron emission in storage rings with their MHz repetition rate. Here, we present a proof-of-principle experiment with at detailed description of our implementation to detect the longitudinal electron bunch profiles via single-shot, near-field electro-optical sampling at the Karlsruhe Research Accelerator (KARA). Our experiment is equipped with an ultra-fast line array camera providing a high-throughput MHz data stream. We characterize statis…
The parallel operation of multiple undulator lines with a wide spectral range is an important way to increase the efficiency of x-ray free electron laser (XFEL) facilities, especially for machines with high-repetition-rate. In this paper, a delay system based on four double bend achromats is proposed to delay electron beams, thereby changing the arrival time of those delayed electron beams in the accelerating structure behind the system. Combined with kickers, the delay system can be used to generate bunch-to-bunch energy changed electron beams in a continuous wave XFEL facility. Start-to-end …
We discuss the design of the muon capture front end for a μ+-μ- Collider. In the front end, a proton bunch on a target creates secondary pions that drift into a capture transport channel, decaying into muons. A sequence of rf cavities forms the resulting muon beams into strings of bunches of differing energies, aligns the bunches to (nearly) equal central energies, and initiates ionization cooling. The muons are then cooled and accelerated to high energy into a storage ring for high-energy high luminosity collisions. Our initial design is based on the somewhat similar front end of the Internat…
We present a detailed study of the six-dimensional phase space of the electron beam produced by the Cornell Energy Recovery Linac Photoinjector, a high-brightness, high repetition rate (1.3 GHz) DC photoemission source designed to drive a hard x-ray energy recovery linac (ERL). A complete simulation model of the injector has been constructed, verified by measurement, and optimized. Both the horizontal and vertical 2D transverse phase spaces, as well as the time-resolved (sliced) horizontal phase space, were simulated and directly measured at the end of the injector for 19 pC and 77 pC bunches …
This paper reports on a 6 kV modulator built and installed at Fermilab to drive the electron gun anode for the Tevatron Electron Lens (TEL). The TEL was built with the intention of shifting the individual (anti)proton bunch tunes to even out the tune spread among all 36 bunches with the desire of improving Tevatron integrated luminosity. This modulator is essentially a 6 kV arbitrary waveform generator that enables the TEL to define the electron beam intensity on a bunch-by-bunch basis. A voltage waveform is constructed having a 7 μs duration that corresponds to the tune shift requirements of …
Recently, the self-modulation scheme of a weakly pre-bunched electron beam has been proposed [Yan et al., Physical Review Letters 126, 084801 (2021)], which is of great promise for high-repetition-rate seeded free-electron lasers (FELs), such as high-gain harmonic generation (HGHG). In this paper, the self-modulation scheme is systematically analyzed and optimized, and further experiments in which the self-modulator is resonant at the second harmonic of the seed laser are conducted. The three-dimensional numerical simulations show that the required seed laser intensity in the self-modulation s…
We propose a new concept of an electron source for ultrafast electron diffraction with sub-10~fs temporal resolution. Electrons are generated in a laser-plasma accelerator, able to deliver femtosecond electron bunches at 5 MeV energy with kHz repetition rate. The possibility of producing this electron source is demonstrated using Particle-In-Cell simulations. We then use particle tracking simulations to show that this electron beam can be transported and manipulated in a realistic beamline, in order to reach parameters suitable for electron diffraction. The beamline consists of realistic stati…
The interaction of intense particle bunches with plasma can give rise to plasma wakes capable of sustaining gigavolt-per-metre electric fields, which are orders of magnitude higher than provided by state-of-the-art radio-frequency technology. Plasma wakefields can, therefore, strongly accelerate charged particles and offer the opportunity to reach higher particle energies with smaller and hence more widely available accelerator facilities. However, the luminosity and brilliance demands of high-energy physics and photon science require particle bunches to be accelerated at repetition rates of t…
Proton beams with up to 100 pC bunch charge, 0.48 MeV cut-off energy and divergence as low as a $3^{\circ}$ were generated from solid targets at kHz repetition rate by a few-mJ femtosecond laser under controlled plasma conditions. The beam spatial profile was measured using a small aperture scanning time-of-flight detector. Detailed parametric studies were performed by varying the surface plasma scale length from 8 to 80 nm and the laser pulse duration from 4 fs to 1.5 ps. Numerical simulations are in good agreement with observations and, together with an in-depth theoretical analysis of the a…
We demonstrate laser wakefield acceleration of quasi-monoenergetic electron bunches up to 15 MeV at 1 kHz repetition rate with 2.5 pC charge per bunch and a core with < 7 mrad beam divergence. Acceleration is driven by 5 fs, < 2.7 mJ laser pulses incident on a thin, near-critical density hydrogen gas jet. Low beam divergence is attributed to reduced sensitivity to laser carrier envelope phase slip, achieved in two ways using laser polarization and gas jet control: (1) electron injection into the wake on the gas jet's plasma density downramp, and (2) use of circularly polarized drive pulses. Un…
Fine time-resolved analysis of matter - i.e. spectroscopy and photon scattering - in the linear response regime requires a fs-scale pulsed, high repetition rate, fully coherent X-ray source. A seeded Free-Electron Laser (FEL) driven by a Super-Conducting Linac, generating $10^{8}$-$10^{10}$ coherent photons at 2-5 keV with abou 0.5 MHz of repetition rate, can address this need. The seeding scheme proposed is the Echo-Enabled Harmonic Generation, alimented by a FEL Oscillator working at 13.6 nm with a cavity based on Mo-Si mirrors. The whole chain of the X-ray generation is here described by me…
We present the development of a high power fibre laser system to investigate its suitability for use in a transverse electron beam profile monitor i.e. a laserwire. A system capable of producing individual pulses up to $165.8 \pm 0.4 μ$J at 1036 nm with a full-width at half-maximum of $1.92 \pm 0.12$ps at 6.49 MHz is demonstrated using a master oscillator power amplifier design with a final amplification stage in a rod-type photonic crystal fibre. The pulses are produced in trains of 1 ms in a novel burst mode amplification scheme to match the bunch pattern of the charged particles in an accel…
SLAC National Accelerator Laboratory is collaborating with Arizona State University to design a LLRF system towards the advancement of the ASU Compact X-ray Light Source (CXLS). The CXLS is a phased project to develop small brilliant x-ray sources that may produce coherent x-rays appropriate as a seed source for LCLS and LCLS II. The CXLS electron beam is produced by an x-band photoinjector and linac operating at 9.3 GHz RF frequency and 1 kHz repetition rate with up to 300 pC per bunch. The linac consists of 3 short 20-cell sections of standing wave linac. The RF gun and linac sections are po…
Accelerator-based terahertz (THz) radiation has been expected to realize a high-power broadband source. Employing a low-emittance and short-bunch electron beam at a high repetition rate, a scheme of coherent diffraction-radiation in an optical cavity layout is proposed. The scheme's stimulated radiation process between bunches can greatly enhance the efficiency of the radiation emission. We performed an experiment with a superconducting linac constructed as an energy recovery linac (ERL) test facility. The electron beam passes through small holes in the cavity mirrors without being destroyed. …
Electromagnetic radiation in the soft x-ray spectral range ($1-100~\rm{nm}$ wavelengths or $0.01-1~\rm{keV}$ photon energies) is rapidly gaining importance in both fundamental research and industrial applications. At present the degree of coherence and the average photon flux required by advanced applications is only available at large-scale synchrotron facilities and Free Electron Lasers (FELs), severely limiting the range of applications. We propose a fully coherent soft x-ray source, based on Inverse Compton Scattering (ICS) of electron bunches created by photoionization of a laser-cooled a…
The research is aimed to address issues of analysis and mitigation of high repetition rate effects in Dielectric Wakefield Accelerators, and more specifically, to study charging rate and charge distribution in a thin walled dielectric wakefield accelerator from a passing charge bunch and the physics of conductivity and discharge phenomena in dielectric materials useful for such accelerator applications. The issue is the role played by the beam halo and intense wakefields in charging of the dielectric, possibly leading to undesired deflection of charge bunches and degradation of the dielectric …
A compact Inverse Compton Light Source (ICLS) design is presented, with flux and brilliance orders of magnitude beyond conventional laboratory-scale sources and other compact ICLS designs. This design utilizes the physics of inverse Compton scattering of an extremely low emittance electron beam by a laser pulse of rms length of approximately two-thirds of a picosecond (2/3 ps). The accelerator is composed of a superconducting radiofrequency (SRF) reentrant gun followed by four double-spoke SRF cavities. After the linac are three quadrupole magnets to focus the electron beam to the interaction …
A high-current emittance-compensated RF photoinjector is a key enabling technology for a high-power CW FEL. A preliminary design of a normal-conducting, 2.5-cell pi-mode, 700-MHz CW RF photoinjector that will be built for demonstration purposes, is completed. This photoinjector will be capable of accelerating a 100-mA electron beam (3 nC per bunch at 35 MHz bunch repetition rate) to 2.7 MeV while providing an emittance below 7 mm-mrad at the wiggler. More than 1 MW of RF power will be fed into the photoinjector cavity through two ridge-loaded tapered waveguides. The waveguides are coupled to t…
Fermilab's Superconducting RF Beam Test Facility currently under construction will produce electron beams capable of damaging the acceleration structures and the beam line vacuum chambers in the event of an aberrant accelerator pulse. The accelerator is being designed with the capability to operate with up to 3000 bunches per macro-pulse, 5Hz repetition rate and 1.5 GeV beam energy. It will be able to sustain an average beam power of 72 KW at the bunch charge of 3.2 nC. Operation at full intensity will deposit enough energy in niobium material to approach the melting point of 2500 °C. In the e…
We describe a compact THz-pump and X-ray-probe beamline, based on an electron linac, for ultrafast time-resolved diffraction applications. Two high-energy electron ($γ>50$) bunches, $5~$ns apart, impinge upon a single-foil or a multifoil radiator and generate THz radiation and X-rays simultaneously. The THz pulse from the first bunch is synchronized to the X-ray beam of the second bunch by using an adjustable optical delay of THz pulse. The peak power of THz radiation from the multifoil radiator is estimated to be $0.14~$GW for a $200~$pC well-optimized electron bunch. GEANT4 simulations show …
A design for a compact x-ray light source (CXLS) with flux and brilliance orders of magnitude beyond existing laboratory scale sources is presented. The source is based on inverse Compton scattering of a high brightness electron bunch on a picosecond laser pulse. The accelerator is a novel high-efficiency standing-wave linac and RF photoinjector powered by a single ultrastable RF transmitter at x-band RF frequency. The high efficiency permits operation at repetition rates up to 1 kHz, which is further boosted to 100 kHz by operating with trains of 100 bunches of 100 pC charge, each separated b…
Phase-Stable Self-Modulation for GHz Continuous-Wave Ultrafast X-Ray Free-Electron Lasers
Shanghai Advanced Research Institute, Chinese Academy of Sciences（中国科学院上海高等研究院）；University of Chinese Academy of Sciences（中国科学院大学）；Zhangjiang Laboratory（张江实验室）
We report the direct observations of sub-macropulse beam centroid oscillations correlated with higher order modes (HOMs) which were generated by off-axis electron beam steering in TESLA-type superconducting RF cavities. The experiments were performed at the Fermilab Accelerator Science and Technology (FAST) facility using its unique configuration of a photocathode rf gun injecting beam into two separated 9-cell cavities in series with corrector magnets and beam position monitors (BPMs) located before, between, and after them. Oscillations of ~100 kHz in the vertical plane and ~380 kHz in the h…
The description of physical processes with many-particle systems is a key approach to the modeling of countless physical systems. In storage rings, where ultrarelativistic particles are agglomerated in dense bunches, the measurement of their phase-space distribution (PSD) is of paramount importance: at any time the PSD not only determines the complete space-time evolution but also provides fundamental performance characteristics for storage ring operation. Here, we demonstrate a non-destructive tomographic imaging technique for the 2D longitudinal PSD of ultrarelativistic electron bunches. For…
High brightness, high repetition rate electron beams are key components for optimizing the performance of next generation scientific instruments, such as MHz-class X-ray Free Electron Laser (XFEL) and Ultra-fast Electron Diffraction/Microscopy (UED/UEM). In the Advanced Photo-injector EXperiment (APEX) at Berkeley Lab, a photoelectron gun based on a 185.7 MHz normal conducting re-entrant RF cavity, has been proven to be a feasible solution to provide high brightness, high repetition rate electron beam for both XFEL and UED/UEM. Based on the success of APEX, a new electron gun system, named APE…
This paper presents one of the case studies of the Gamma Factory initiative -- a proposal of a new operation scheme of ion beams in the CERN accelerator complex. Its goal is to extend the scope and precision of the LHC-based research by complementing the proton-proton collision programme with the high-luminosity nucleus-nucleus one. Its numerous physics highlights include studies of the exclusive Higgs-boson production in photon-photon collisions and precision measurements of the electroweak (EW) parameters. There are two principal ways to increase the LHC luminosity which do not require an up…
Antiprotons in Fermilab's Recycler ring are cooled by a 4.3 MeV, 0.1 - 0.5 A DC electron beam (as well as by a stochastic cooling system). The unique combination of the relativistic energy (γ = 9.49), an Ampere - range DC beam, and a relatively weak focusing makes the cooling efficiency particularly sensitive to ion neutralization. A capability to clear ions was recently implemented by way of interrupting the electron beam for 1-30 \mus with a repetition rate of up to 40 Hz. The cooling properties of the electron beam were analyzed with drag rate measurements and showed that accumulated ions s…
A neutron source is proposed. It is based on a proton accelerator with the energy Ep = 1.2 GeV, current Ip = 0.7A, pulse duration T = 3 mcsec, repetition rate F = 60 Hz, and accelerator length L = 30 m. Protons are accelerated by the field of electron rings. The electron rings are formed from a tube beam by way of modulation and creating rotating motion by crossing the magnetic field cusp. The frequency of modulation f1 = 142.8 MHz. The bunch is accelerated at the frequency f3 = 2856 MHz. The high frequency power required for making the field is P1 = 6 - 150 MW/section, the power transferred t…
