Based on energy conservation, we derive a critical condition theoretically for electrowettinginduced droplet detachment from a hydrophobic curved surface. Phase diagrams are constructed in terms of droplet volume, viscosity, Ohnesorge number, friction coefficient at contact line, surface curvature, surface wettability and electrowetting number. The deduced critical condition offers a general and quantitative prediction on when the detachment occurs, a criterion enabling us to gain more insights into how to accurately manipulate the electrowetting-induced detachment of an aqueous droplet on a curved surface. The results obtained in this paper also imply that the detachable regimes of the phase diagrams can be enlarged through increasing droplet volume and surface curvature, and reducing liquid viscosity, friction coefficient, Ohnesorge number and wettability of substrates.
Even though electrowetting-on-dielectric (EWOD) is a useful strategy in a wide array of biological and engineering processes with numerous droplet-manipulation applications, there is still a lack of complete theoretical interpretation on the dynamics of electrowetting. In this paper, we present an effective theoretical model and use Onsager variational principle to successfully derive the governing equations of non-equilibrium electrowetting dynamics for a droplet in both overdamped and underdamped regimes. It is found that the spreading and retraction dynamics of a droplet on EWOD substrates …
Floating electrode electrowetting is caused by dc voltage applied to a liquid droplet on the Cytop surface, without electrical connection to the substrate. The effect is caused by the charge separation in the floating electrode. A highly-resistive thermally-grown SiO2 layer underneath the Cytop enables the droplet to hold charges without leakage, which is the key contribution. Electrowetting with an SiO2 layer shows a memory effect, where the wetting angle stays the same after the auxiliary electrode is removed from the droplet in both conventional and floating electrode electrowetting. Floati…
Molecular dynamics simulations were employed to study the wetting behavior of nanoscale aqueous hydrophilic and hydrophobic Imidazolium based ionic liquid (IL) droplets on a solid graphite substrate subjected to the perpendicular electric field. Imminent transformation in the droplet configuration was observed at E = 0.08 V/Å both for hydrophobic ILs [EMIM][NTF2] and SPC/E water droplets. However, for hydrophilic, [EMIM][BF4], the droplet wets asymmetrically within electric field E = 0.09 V/Å for lower weight percentages of ILs and E = 0.1 V/Å at a higher weight percentage of ILs (i.e., 50wt%)…
The pinning of the contact line adversely influences the electrowetting performance of sessile liquid droplets. In this paper, we report the electrowetting hysteresis characteristics of 100 mM aq. KCl sessile liquid droplet placed on a hydrophobic PDMS surface. The effect of nanoparticles on the contact angle hysteresis under the imposed electric potential is further investigated. This study reveals that the contact angle hysteresis decreases beyond a certain threshold value of nanoparticles concentration. Therefore, nanoparticle suspension in the liquid droplet can be used to enhance or suppr…
Dynamic Wettability Modulation of Textured, Soft and LIS Interfaces Using Electrowetting
School of Mechanical Sciences, Indian Institute of Technology (IIT) Goa（印度理工学院果阿分校机械科学学院）；Department of Mechanical Engineering, Indian Institute of Technology, Kharagpur（印度理工学院卡拉格普尔分校机械工程系）
Electrowetting-on-dielectric (EWOD) is a powerful tool in many droplet-manipulation applications with a notorious weakness caused by contact-angle saturation (CAS), a phenomenon limiting the equilibrium contact angle of an EWOD-actuated droplet at high applied voltage. In this paper, we study the spreading behaviours of droplets on EWOD substrates with the range of applied voltage exceeding the saturation limit. We experimentally find that at the initial stage of spreading, the driving force at the contact line still follows the Young-Lippmann law even if the applied voltage is higher than the…
Understanding the critical condition and mechanism of the droplet wetting transition between Cassie-Baxter state and Wenzel state triggered by an external electric field is of considerable importance because of its numerous applications in industry and engineering. However, such a wetting transition on a patterned surface is still not fully understood, e.g., the effects of electro-wetting number, geometry of the patterned surfaces, and droplet volume on the transition have not been systematically investigated. In this paper, we propose a theoretical model for the Cassie-Baxter- Wenzel wetting …
During detachment of a viscous fluid extruded from a nozzle a filament linking the droplet to the latter is formed. Under the effect of surface tension the filament thins until pinch off and final detachment of the droplet. In this paper we study the effect of the presence of individual particles trapped in the filament on the detachment dynamics using granular suspensions of small volume fractions (ϕ < 6%). We show that even a single particle strongly modifies the detachment dynamics. The particle perturbs the thinning of the thread and a large droplet of fluid around the particle is formed. …
The presence of a very small amount of high molecular weight polymer significantly delays the pinch-off singularity of a drop of water falling from a faucet, and leads to the formation of a long-lived cylindrical filament. In this paper we present experiments, numerical simulations, and theory which examines the pinch-off process in the presence of polymers. The numerical simulations are found to be in excellent agreement with experiment. As a test case, we establish the conditions under which a small bead remains on the filament; we find that this is due to the asymmetry induced by the self-s…
The wetting of solid surfaces can be manoeuvred by altering the energy balance at the interfacial region. While electric field acts favourably to spread a droplet on a rigid surface, this tendency may be significantly suppressed over soft surfaces, considering a part of the interfacial energy being utilized to deform the solid elastically by capillary forces. Here, we bring out a unique mechanism by virtue of which addition of nano-particles to the droplet brings in a favourable recovery of the electro-spreading characteristics of a soft surface, by realizing an alteration in the effective die…
We use the Poisson-Boltzmann theory to predict contact angle saturation of aqueous droplets in electrowetting. Our theory predicts that injection of ions from the droplet into its surrounding medium is responsible for the deviation of the apparent contact angle from the Young-Lippmann equation for large applied voltages. The ion injection substantially decreases the Maxwell stress and increases the osmotic pressure at the interface between the two media, leading to saturation of the apparent contact angle. Moreover, we find that the contact angle does not saturate, but only has a broad minimum…
A proof-of-concept demonstration of the electrowetting-on-dielectric of a sessile soap bubble is reported here. The bubbles are generated using a commercial soap bubble mixture - the surfaces are composed of highly doped, commercial silicon wafers covered with nanometre thick films of Teflon. Voltages less than 40V are sufficient to observe the modification of the bubble shape and the apparent bubble contact angle. Such observations open the way to inter alia the possibility of bubble-transport, as opposed to droplet-transport, in fluidic microsystems (e.g. laboratory-on-a-chip) - the potentia…
Recent experiments by Kavousanakis et al., Langmuir, 2018 [1], showed that reversible electrowetting on superhydrophobic surfaces can be achieved by using a thick solid dielectric layer (e.g. tens of micrometers). It has also been shown, through equilibrium (static) computations, that when the dielectric layer is thick enough the electrostatic pressure is smoothly distributed along the droplet surface, thus the irreversible Cassie to Wenzel wetting transitions can be prevented. In the present work we perform more realistic, dynamic simulations of the electrostatically-induced spreading on supe…
When a droplet is generated, the ligament connecting the drop to the nozzle thins down and eventually pinches off. Adding solid particles to the liquid phase leads to a more complex dynamic, notably by increasing the shear viscosity. Moreover, it introduces an additional length scale to the system, the diameter of the particles, which eventually becomes comparable to the diameter of the ligament. In this paper, we experimentally investigate the thinning and pinch-off of drops of suspensions with two different sizes of particles. We characterize the thinning for different particle size ratios a…
We study here the microscopic deformations of elastic lamellae constituting a superhydrophobic substrate under different wetting conditions of a sessile droplet using electrowetting. The deformation profiles of the lamellae are experimentally evaluated using confocal microscopy. These experimental results are then explained using a variational principle formalism within the framework of linear elasticity. We show that the local deformation profile of a lamella is mainly controlled by the net horizontal component of the capillary forces acting on its top due to the pinned droplet contact line. …
We show how anisotropic, grooved features facilitate the trapping and directed transport of droplets on lubricated, liquid-shedding surfaces. Capillary action pins droplets to topographic surface features, enabling transport along the feature while inhibiting motion across (or detachment from) the feature. We demonstrate the robustness of this capillary-based mechanism for directed droplet transport on slippery surfaces by combining experiments on synthetic, lubricant-infused surfaces with observations on the natural trapping surface of a carnivorous pitcher plant. Controlling liquid navigatio…
In this work, we investigate crystallization from droplets formed on micro-patterned surfaces. By solvent exchange in a micro-chamber, a ternary solution consisting of a model compound beta-alanine, water, and isopropanol, was displaced by a flow of isopropanol. In the process, oiling-out droplets formed and crystallized. Our results showed that the shape and size of the crystals on micro-patterned surfaces could be simply mediated by the flow conditions of solvent exchange. Varying flow rate, concentration, or channel height led to the formation of a thin film with micro-holes, connected netw…
The Cassie-Baxter state droplet has many local energy minima on the textured surface, while the amount of the energy barrier between them can be affected by the gravity. When the droplet cannot find any local energy minimum point on the surface, the droplet starts to slide. Based on the Laplace pressure equation, the shape of a two-dimensional Cassie-Baxter droplet on a textured surface is predicted. Then the stability of the droplet is examined by considering the interference between the liquid and the surface microstructure as well as analyzing the free energy change upon the de-pinning. Aft…
The dynamic behavior of a partially wetting polymer droplet driven over a nanostructured interface is studied using molecular dynamics simulations. We consider the bead-spring model to represent a polymeric liquid that partially wets a rough surface composed of a periodic array of spherical particles. It is shown that at sufficiently small values of the external force, the droplet remains pinned at the particles' surface, while above the threshold, its motion consists of alternating periods of pinning and rapid displacements between neighboring particles. The latter process involves large peri…
We study a single, motionless three-dimensional droplet growing by adsorption of diffusing monomers on a 2D substrate. The diffusing monomers are adsorbed at the aggregate perimeter of the droplet with different boundary conditions. Models with both an adsorption boundary condition and a radiation boundary condition, as well as a phenomenological model, are considered and solved in a quasistatic approximation. The latter two models allow particle detachment. In the short time limit, the droplet radius grows as a power of the time with exponents of 1/4, 1/2 and 3/4 for the models with adsorptio…
Advancing and receding angles are physical quantities frequently measured to characterize the wetting properties of a rough surface. Thermodynamically, the advancing and receding angles are often interpreted as the maximum and minimum contact angles that can be formed by a droplet without losing its stability. Despite intensive research on wetting of rough surfaces, the gravitational effect on these angles has been overlooked because most studies have considered droplets smaller than the capillary length. In this study, however, by combining theoretical and numerical modeling, we show that the…
