Deep neural networks (NNs) have exhibited considerable potential for efficiently balancing the performance and complexity of multiple-input and multiple-output (MIMO) detectors. We propose a receiver framework that enables efficient online training by leveraging the following simple observation: although NN parameters should adapt to channels, not all of them are channel-sensitive. In particular, we use a deep unfolded NN structure that represents iterative algorithms in signal detection and channel decoding modules as multi layer deep feed forward networks. An expectation propagation (EP) module, called EPNet, is established for signal detection by unfolding the EP algorithm and rendering the damping factors trainable. An unfolded turbo decoding module, called TurboNet, is used for channel decoding. This component decodes the turbo code, where trainable NN units are integrated into the traditional max-log-maximum a posteriori decoding procedure. We demonstrate that TurboNet is robust for channels and requires only one off-line training. Therefore, only a few damping factors in EPNet must be re-optimized online. An online training mechanism based on meta learning is then developed. Here, the optimizer, which is implemented by long short-term memory NNs, is trained to update damping factors efficiently by using a small training set such that they can quickly adapt to new environments. Simulation results indicate that the proposed receiver significantly outperforms traditional receivers and that the online learning mechanism can quickly adapt to new environments. Furthermore, an over-the-air platform is presented to demonstrate the significant robustness of the proposed receiver in practical deployment.
Expectation Propagation (EP)-based Multiple-Input Multiple-Output (MIMO) detector is regarded as a state-of-the-art MIMO detector because of its exceptional performance. However, we find that the EP MIMO detector cannot guarantee to achieve the optimal performance due to the empirical parameter selection, including initial variance and damping factors. According to the influence of the moment matching and parameter selection for the performance of the EP MIMO detector, we propose a modified EP MIMO detector (MEPD). In order to obtain the optimal initial variance and damping factors, we adopt a…
An alternate direction method of multipliers (ADMM)-based detectors can achieve good performance in both small and large-scale multiple-input multiple-output (MIMO) systems. However, due to the difficulty of choosing the optimal penalty parameters, their performance is limited. This paper presents a deep neural network (DNN)-based massive MIMO detection method which can overcome the above limitation. It exploits the unfolding technique and learns to estimate the penalty parameters. Additionally, a computationally cheaper detector is also proposed. The proposed methods can handle the higher-ord…
We propose a multiple-input multiple-output (MIMO) detector based on an annealed version of the \emph{underdamped} Langevin (stochastic) dynamic. Our detector achieves state-of-the-art performance in terms of symbol error rate (SER) while keeping the computational complexity in check. Indeed, our method can be easily tuned to strike the right balance between computational complexity and performance as required by the application at hand. This balance is achieved by tuning hyperparameters that control the length of the simulated Langevin dynamic. Through numerical experiments, we demonstrate th…
This paper presents a low complexity detector for multiple-input multiple-output (MIMO) systems based on the recently proposed orthogonal time frequency space (OTFS) modulation. In the proposed detector, the copies of the transmitted symbol-vectors received through the different diversity branches (propagation paths and receive antennas) are linearly combined using the maximum ratio combining (MRC) technique to iteratively improve the signal to interference plus noise ratio (SINR) at the output of the combiner. To alleviate the performance degradation due to spatial correlation at the receiver…
Low-resolution analog-to-digital converters (ADCs) have been considered as a practical and promising solution for reducing cost and power consumption in massive Multiple-Input-Multiple-Output (MIMO) systems. Unfortunately, low-resolution ADCs significantly distort the received signals, and thus make data detection much more challenging. In this paper, we develop a new deep neural network (DNN) framework for efficient and low-complexity data detection in low-resolution massive MIMO systems. Based on reformulated maximum likelihood detection problems, we propose two model-driven DNN-based detect…
In this paper, we analyze the performance of evolutionary heuristic-aided linear detectors deployed in Multiple-Input Multiple-Output (MIMO) Orthogonal Frequency-Division Multiplexing (OFDM) systems, considering realistic operating scenarios. Hybrid linear-heuristic detectors under different initial solutions provided by linear detectors are considered, namely differential evolution (DE) and particle swarm optimization (PSO). Numerical results demonstrated the applicability of hybrid detection approach, which can improve considerably the performance of minimum mean-square error (MMSE) and matc…
In this work, the behaviour of bit error rates for both conventional and massive MIMO systems with high order constellations, which are essential to achieve spectral efficiency for 5G standard communications, has been evaluated. We have used real-domain Schnorr Euchner enumeration with K-best algorithm to reduce computational complexity of detection. The results, presented in this letter, have outperformed existing detection algorithms in terms of complexity and BER, especially in low SNR regions, for both massive and conventional MIMO systems. We performed simulations for N $\times$ N MIMO sy…
This work analyzes the performance of the implementable detectors for multiple-input-multiple-output (MIMO) orthogonal frequency division multiplexing (OFDM) technique under specific and realistic operation system condi- tions, including antenna correlation and array configuration. Time-domain channel model has been used to evaluate the system performance under realistic communication channel and system scenarios, including different channel correlation, modulation order and antenna arrays configurations. A bunch of MIMO-OFDM detectors were analyzed for the purpose of achieve high performance …
Cell-free (CF) massive multiple-input multiple-output (M-MIMO) technology plays a prominent role in the beyond fifth-generation (5G) networks. However, designing a high performance CF M-MIMO detector is a challenging task due to the presence of pilot contamination which appears when the number of pilot sequences is smaller than the number of users. This work proposes a CF M-MIMO detector referred to as CF expectation propagation (CF-EP) that incorporates the pilot contamination when calculating the posterior belief. The simulation results show that the proposed detector achieves significant im…
In this paper, an efficient massive multiple-input multiple-output (MIMO) detector is proposed by employing a deep neural network (DNN). Specifically, we first unfold an existing iterative detection algorithm into the DNN structure, such that the detection task can be implemented by deep learning (DL) approach. We then introduce two auxiliary parameters at each layer to better cancel multiuser interference (MUI). The first parameter is to generate the residual error vector while the second one is to adjust the relationship among previous layers. We further design the training procedure to opti…
Optimal symbol detection in multiple-input multiple-output (MIMO) systems is known to be an NP-hard problem. Hence, the objective of any detector of practical relevance is to get reasonably close to the optimal solution while keeping the computational complexity in check. In this work, we propose a MIMO detector based on an annealed version of Langevin (stochastic) dynamics. More precisely, we define a stochastic dynamical process whose stationary distribution coincides with the posterior distribution of the symbols given our observations. In essence, this allows us to approximate the maximum …
This paper firstly introduces our shared Matlab source code that simulates the two optimal-ordered SIC detectors proposed in [1] and [2]. Based on our shared Matlab code, we compare the computational complexities between the two detectors in [1] and [2] by theoretical complexity calculations and numerical experiments. We carry out theoretical complexity calculations to obtain the worst-case complexities for the two detectors in [1] and [2]. Then from the theoretical worst-case complexities, we make the conclusion that the detector proposed in [2] requires 9N 2 more floating-point operations (f…
In this paper, we have analyzed the performance-complexity tradeoff of {a selective} likelihood ascent search (LAS) algorithm initialized by a linear detector, such as matched filtering (MF), zero forcing (ZF) and minimum mean square error (MMSE), {and considering an optimization factor $ρ$ from the bit flipping rule}. The scenario is the uplink of a massive MIMO (M-MIMO) system, and the {analysis has }been developed by means of computer simulations. With the increasing number of base station (BS) antennas, the classical detectors become inefficient. Therefore, the LAS is employed for performa…
In this paper, we develop a dynamic detection network (DDNet) based detector for multiple-input multiple-output (MIMO) systems. By constructing an improved DetNet (IDetNet) detector and the OAMPNet detector as two independent network branches, the DDNet detector performs sample-wise dynamic routing to adaptively select a better one between the IDetNet and the OAMPNet detectors for every samples under different system conditions. To avoid the prohibitive transmission overhead of dataset collection in centralized learning (CL), we propose the federated averaging (FedAve)-DDNet detector, where al…
Incorporating deep learning (DL) into multiple-input multiple-output (MIMO) detection has been deemed as a promising technique for future wireless communications. However, most DL-based detection algorithms are lack of theoretical interpretation on internal mechanisms and could not provide general guidance on network design. In this paper, we analyze the performance of DL-based MIMO detection to better understand its strengths and weaknesses. We investigate two different architectures: a data-driven DL detector with a neural network activated by rectifier linear unit (ReLU) function and a mode…
In this paper, we design an efficient quadrature amplitude modulation (QAM) signal detector for massive multiple-input multiple-output (MIMO) communication systems via the penalty-sharing alternating direction method of multipliers (PS-ADMM). Its main content is as follows: first, we formulate QAM-MIMO detection as a maximum-likelihood optimization problem with bound relaxation constraints. Decomposing QAM signals into a sum of multiple binary variables and exploiting introduced binary variables as penalty functions, we transform the detection optimization model to a non-convex sharing problem…
Target detection is an important problem in multiple-input multiple-output (MIMO) radar. Many existing target detection algorithms were proposed without taking into consideration the quantization error caused by analog-to-digital converters (ADCs). This paper addresses the problem of target detection for MIMO radar with one-bit ADCs and derives a Rao's test-based detector. The proposed method has several appealing features: 1) it is a closed-form detector; 2) it allows us to handle sign measurements straightforwardly; 3) there are closed-form approximations of the detector's distributions, whi…
We investigate a turbo soft detector based on the expectation propagation (EP) algorithm for large-scale multiple-input multiple-output (MIMO) systems. Optimal detection in MIMO systems becomes computationally unfeasible for high-order modulations and/or large number of antennas. In this situation, the linear minimum mean square error (LMMSE) exhibits a low-complexity with a good performance, however far from optimal. To improve the performance, the EP algorithm can be used. In this paper, we review previous EP-based detectors and enhance their estimation in terms of complexity and performance…
Solving the optimal symbol detection problem in multiple-input multiple-output (MIMO) systems is known to be NP-hard. Hence, the objective of any detector of practical relevance is to get reasonably close to the optimal solution while keeping the computational complexity in check. In this work, we propose a MIMO detector based on an annealed version of Langevin (stochastic) dynamics. More precisely, we define a stochastic dynamical process whose stationary distribution coincides with the posterior distribution of the symbols given our observations. In essence, this allows us to approximate the…
Although routinely utilized in literature, orthogonal waveforms may lose orthogonality in distributed multi-input multi-output (MIMO) radar with spatially separated transmit (TX) and receive (RX) antennas, as the waveforms may experience distinct delays and Doppler frequency offsets unique to different TX-RX propagation paths. In such cases, the output of each waveform-specific matched filter (MF), employed to unravel the waveforms at the RXs, contains both an \auto term and multiple cross terms, i.e., the filtered response of the desired and, respectively, undesired waveforms. We consider the…
In this paper, we propose to dynamically select a MIMO detector using neural network for each resource element (RE) in the transport block of 5G NR/LTE communication system. The objective is to minimize the computational complexity of MIMO detection while keeping the transport block error rate (BLER) close to the BLER when dimension-reduced maximum-likelihood (DR-ML) detection is used. A detector selection problem is formulated to achieve this objective. However, since the problem is high dimensional and NP-hard, we first decompose the problem into smaller problems and train a multi-layer perc…
Southeast University（东南大学）；National Sun Yat-sen University（国立中山大学）；Georgia Institute of Technology（佐治亚理工学院）
In this paper, we investigate the model-driven deep learning (DL) for MIMO detection. In particular, the MIMO detector is specially designed by unfolding an iterative algorithm and adding some trainable parameters. Since the number of trainable parameters is much fewer than the data-driven DL based signal detector, the model-driven DL based MIMO detector can be rapidly trained with a much smaller data set. The proposed MIMO detector can be extended to soft-input soft-output detection easily. Furthermore, we investigate joint MIMO channel estimation and signal detection (JCESD), where the detec…
Multiuser massive multiple-input multiple-output (MU-MIMO) systems can be used to meet high throughput requirements of 5G and beyond networks. In an uplink MUMIMO system, a base station is serving a large number of users, leading to a strong multi-user interference (MUI). Designing a high performance detector in the presence of a strong MUI is a challenging problem. This work proposes a novel detector based on the concepts of expectation propagation (EP) and graph neural network, referred to as the GEPNet detector, addressing the limitation of the independent Gaussian approximation in EP. The …
Multi-user multiple-input multiple-output (MU-MIMO) systems can be used to meet high throughput requirements of 5G and beyond networks. A base station serves many users in an uplink MU-MIMO system, leading to a substantial multi-user interference (MUI). Designing a high-performance detector for dealing with a strong MUI is challenging. This paper analyses the performance degradation caused by the posterior distribution approximation used in the state-of-the-art message passing (MP) detectors in the presence of high MUI. We develop a graph neural network based framework to fine-tune the MP dete…
The stringent requirements on reliability and processing delay in the fifth-generation ($5$G) cellular networks introduce considerable challenges in the design of massive multiple-input-multiple-output (M-MIMO) receivers. The two main components of an M-MIMO receiver are a detector and a decoder. To improve the trade-off between reliability and complexity, a Bayesian concept has been considered as a promising approach that enhances classical detectors, e.g. minimum-mean-square-error detector. This work proposes an iterative M-MIMO detector based on a Bayesian framework, a parallel interference…
In this paper, we present a differential modulation and detection scheme for use in the uplink of a system with a large number of antennas at the base station, each equipped with low-resolution analog-to-digital converters (ADCs). We derive an expression for the maximum likelihood (ML) detector of a differentially encoded phase information symbol received by a base station operating in the low-resolution ADC regime. We also present an equal performing reduced complexity receiver for detecting the phase information. To increase the supported data rate, we also present a maximum likelihood expre…
In this paper, the efficiency of various MIMO detectors was analyzed from the perspective of highly correlated channels, where MIMO systems have a lack of performance, besides in some cases an increasing complexity. Considering this hard, but {a useful} scenario, various MIMO detection schemes {were accurately evaluated concerning} complexity and bit error rate (BER) performance. Specifically, successive interference cancellation (SIC), lattice reduction (LR) and the combination of them were associated with conventional linear MIMO detection techniques. {To demonstrate effectiveness}, a wide r…
This article presents a differential detection scheme for the uplink of a massive MIMO system that employs one-bit quantizers on each receive antenna. We focus on the detection of differential amplitude and phase shift keying symbols and we use the Bussgang theorem to express the quantized received signal in terms of quantized signals received during previous channel uses. Subsequently, we derive the maximum likelihood detector for the differentially encoded amplitude and phase information symbols. We note that while the one-bit detector can decode the differentially encoded phase information …
Index modulation (IM) brings the reduction of power consumption and complexity of the transmitter to classical multiple-input multiple-output orthogonal frequency division multiplexing (MIMO-OFDM) systems. However, due to the introduction of IM, the complexity of the detector at receiver is greatly increased. Furthermore, the detector also requires the channel state information at receiver, which leads to high system overhead. To tackle these challenges, in this paper, we introduce deep learning (DL) in designing a non-iterative detector. Specifically, based on the structural sparsity of the t…
In the present work, a reinforcement learning (RL) based adaptive algorithm to optimise the transmit beampattern for a colocated massive MIMO radar is presented. Under the massive MIMO regime, a robust Wald type detector, able to guarantee certain detection performances under a wide range of practical disturbance models, has been recently proposed. Furthermore, an RL/cognitive methodology has been exploited to improve the detection performance by learning and interacting with the surrounding unknown environment. Building upon previous findings, we develop here a fully adaptive and data driven …
In this letter, we develop an $\ell_2$-box maximum likelihood (ML) formulation for massive multiple-input multiple-output (MIMO) quadrature amplitude modulation (QAM) signal detection and customize an alternating direction method of multipliers (ADMM) algorithm to solve the nonconvex optimization model. In the $\ell_2$-box ADMM implementation, all variables are solved analytically. Moreover, several theoretical results related to convergence, iteration complexity, and computational complexity are presented. Simulation results demonstrate the effectiveness of the proposed $\ell_2$-box ADMM dete…
To provide important prior knowledge for the DOA estimation of UAV emitters in future wireless networks, we present a complete DOA preprocessing system for inferring the number of emitters via massive MIMO receive array. Firstly, in order to eliminate the noise signals, two high-precision signal detectors, square root of maximum eigenvalue times minimum eigenvalue (SR-MME) and geometric mean (GM), are proposed. Compared to other detectors, SR-MME and GM can achieve a high detection probability while maintaining extremely low false alarm probability. Secondly, if the existence of emitters is de…
Multi-user multiple-input multiple-output (MU-MIMO) beamforming design is typically formulated as a non-convex weighted sum rate (WSR) maximization problem that is known to be NP-hard. This problem is solved either by iterative algorithms, which suffer from slow convergence, or more recently by using deep learning tools, which require time-consuming pre-training process. In this paper, we propose a low-complexity meta-learning based gradient descent algorithm. A meta network with lightweight architecture is applied to learn an adaptive gradient descent update rule to directly optimize the beam…
In this paper, deep neural network (DNN) is utilized to improve the belief propagation (BP) detection for massive multiple-input multiple-output (MIMO) systems. A neural network architecture suitable for detection task is firstly introduced by unfolding BP algorithms. DNN MIMO detectors are then proposed based on two modified BP detectors, damped BP and max-sum BP. The correction factors in these algorithms are optimized through deep learning techniques, aiming at improved detection performance. Numerical results are presented to demonstrate the performance of the DNN detectors in comparison w…
We propose an uplink massive MIMO system using an array of holographic metasurfaces as a sector antenna. The antenna consists of a set of rectangular waveguide-fed metasurfaces combined along the elevation direction into a planar aperture, each with subwavelength-sized metamaterial elements as radiators. The metamaterial radiators are designed such that the waveguide-fed metasurface implements a holographic solution for the guided (or reference) mode, generating a fan beam towards a prescribed direction, thereby forming a multibeam antenna system. We demonstrate that a narrowband uplink massiv…
In this paper, we develop an efficient detector for massive multiple-input multiple-output (MIMO) communication systems via penalty-sharing alternating direction method of multipliers (PS-ADMM). Its main content are as follows: first, we formulate the MIMO detection as a maximum-likelihood optimization problem with bound relaxation constraints. Then, the higher modulation signals are decomposed into a sum of multiple binary variables through their inherent structures, by exploiting introduced binary variables as penalty functions, the detection optimization model is equivalent to a nonconvex s…
For massive multiple-input multiple-output (MIMO) systems, linear minimum mean-square error (MMSE) detection has been shown to achieve near-optimal performance but suffers from excessively high complexity due to the large-scale matrix inversion. Being matrix inversion free, detection algorithms based on the Gauss-Seidel (GS) method have been proved more efficient than conventional Neumann series expansion (NSE) based ones. In this paper, an efficient GS-based soft-output data detector for massive MIMO and a corresponding VLSI architecture are proposed. To accelerate the convergence of the GS m…
Efficient signal detectors are rather important yet challenging to achieve satisfactory performance for large-scale communication systems. This paper considers a non-orthogonal sparse code multiple access (SCMA) configuration for multiple-input multiple-output (MIMO) systems with recently proposed orthogonal time frequency space (OTFS) modulation. We develop a novel low-complexity yet effective customized Memory approximate message passing (AMP) algorithm for channel equalization and multi-user detection. Specifically, the proposed Memory AMP detector enjoys the sparsity of the channel matrix …
Index modulation (IM) reduces the power consumption and hardware cost of the multiple-input multiple-output (MIMO) system by activating part of the antennas for data transmission. However, IM significantly increases the complexity of the receiver and needs accurate channel estimation to guarantee its performance. To tackle these challenges, in this paper, we design a deep learning (DL) based detector for the IM aided MIMO (IM-MIMO) systems. We first formulate the detection process as a sparse reconstruction problem by utilizing the inherent attributes of IM. Then, based on greedy strategy, we …
This paper presents a novel data detector ASIC for massive multiuser multiple-input multiple-output (MU-MIMO) wireless systems. The ASIC implements a modified version of the large-MIMO approximate message passing algorithm (LAMA), which achieves near-optimal error-rate performance (i) under realistic channel conditions and (ii) for systems with as many users as base-station (BS) antennas. The hardware architecture supports 32 users transmitting 256-QAM simultaneously and in the same time-frequency resource, and provides soft-input soft-output capabilities for iterative detection and decoding. …
In cell-free massive MIMO networks, an efficient distributed detection algorithm is of significant importance. In this paper, we propose a distributed expectation propagation (EP) detector for cell-free massive MIMO. The detector is composed of two modules, a nonlinear module at the central processing unit (CPU) and a linear module at the access point (AP). The turbo principle in iterative decoding is utilized to compute and pass the extrinsic information between modules. An analytical framework is then provided to characterize the asymptotic performance of the proposed EP detector with a larg…
A neighborhood restricted Mixed Gibbs Sampling (MGS) based approach is proposed for low-complexity high-order modulation large-scale Multiple-Input Multiple-Output (LS-MIMO) detection. The proposed LS-MIMO detector applies a neighborhood limitation (NL) on the noisy solution from the MGS at a distance d - thus, named d-simplified MGS (d-sMGS) - in order to mitigate its impact, which can be harmful when a high order modulation is considered. Numerical simulation results considering 64-QAM demonstrated that the proposed detection method can substantially improve the MGS algorithm convergence, wh…
