Low propagation loss in high confinement waveguides is critical for chip-based nonlinear photonics applications. Sophisticated fabrication processes which yield sub-nm roughness are generally needed to reduce scattering points at the waveguide interfaces in order to achieve ultralow propagation loss. Here, we show ultralow propagation loss by shaping the mode using a highly multimode structure to reduce its overlap with the waveguide interfaces, thus relaxing the fabrication processing requirements. Microresonators with intrinsic quality factors (Q) of 31.8 $\pm$ 4.4 million are experimentally demonstrated. Although the microresonators support 10 transverse modes only the fundamental mode is excited and no higher order modes are observed when using nonlinear adiabatic bends. A record-low threshold pump power of 73 $μ$W for parametric oscillation is measured and a broadband, almost octave spanning single-soliton frequency comb without any signatures of higher order modes in the spectrum spanning from 1097 nm to 2040 nm (126 THz) is generated in the multimode microresonator. This work provides a design method that could be applied to different material platforms to achieve and use ultrahigh-Q multimode microresonators.
Dissipative Kerr soliton (DKS) frequency combs - also known as microcombs - have arguably created a new field in cavity nonlinear photonics, with a strong cross-fertilization between theoretical, experimental, and technological research. Spatiotemporal mode-locking (STML) not only add new degrees of freedom to ultrafast laser technology, but also provide new insights for implementing analogue computers and heuristic optimizers with photonics. Here, we combine the principles of DKS and STML for the first time to demonstrate the STML DKS by developing an unexplored ultrahigh-quality-factor Fabry…
The synthesis of ultralow-noise microwaves is of both scientific and technological relevance for timing, metrology, communications and radio-astronomy. Today, the lowest reported phase noise signals are obtained via optical frequency-division using mode-locked laser frequency combs. Nonetheless, this technique ideally requires high repetition rates and tight comb stabilisation. Here, a soliton microcomb with a 14 GHz repetition rate is generated with an ultra-stable pump laser and used to derive an ultralow-noise microwave reference signal, with an absolute phase noise level below -60 dBc/Hz a…
We proposed a refractive index (RI) sensing method with temperature compensation by using an optical frequency comb (OFC) sensing cavity employing a multimode-interference (MMI) fiber, namely, the MMI-OFC sensing cavity. The MMI-OFC sensing cavity enables simultaneous measurement of material-dependent RI and sample temperature by decoding from the comb spacing frequency shift and the wavelength shift of the OFC. We realized the simultaneous and continuous measurement of RI-related concentration of a liquid sample and its temperature with precisions of 1.6*10^-4 RIU and 0.08 degree. The propose…
The foundry development of integrated photonics has revolutionized today's optical interconnect and datacenters. Over the last decade, we have witnessed the rising of silicon nitride (Si$_3$N$_4$) integrated photonics, which is currently transferring from laboratory research to foundry manufacturing. The development and transition are triggered by the ultimate need of low optical loss offered by Si$_3$N$_4$, which is beyond the reach of silicon and III-V semiconductors. Combined with modest Kerr nonlinearity, tight optical confinement and dispersion engineering, Si$_3$N$_4$ has today become th…
Smooth-Curvature Bend Design Guided by Variational Analysis for Adiabatic Multimode Integrated Photonics
Wuhan National Laboratory for Optoelectronics, Huazhong University of Science and Technology（华中科技大学武汉国家光电研究中心）；School of Optical and Electronic Information, Huazhong University of Science and Technology（华中科技大学光学与电子信息学院）；Optics Valley Laboratory（光谷实验室）
A drawback of high-quality modes in optical microdisks is their isotropic light emission characteristics. Here we report a novel, robust, and general mechanism that results in highly directional light emission from those modes. This surprising finding is explained by a combination of wave phenomena (wave localization along unstable periodic ray trajectories) and chaotic ray dynamics in open systems (escape along unstable manifolds). The emission properties originating in the chaotic ray dynamics permit directional light output even from microlasers operating in the common multi-mode regime. We…
Nonlinear photonics based on integrated circuits has enabled applications such as parametric amplifiers, soliton frequency combs, supercontinua, and non-reciprocal devices. Ultralow optical loss and the capability for dispersion engineering are essential, which necessitate the use of multi-mode waveguides. Despite that rich interaction among different spatial waveguide eigenmodes can give rise to novel nonlinear phenomena, spatial mode interaction is typically undesired as it increases optical loss, perturbs local dispersion profile, and impedes soliton formation. Adiabatic bends, such as Eule…
Multimode nonclassical states of light are an essential resource in quantum computation with continuous variables, for example in cluster state computation. They can be generated either by mixing different squeezed light sources using linear optical operations, or directly in a multimode optical device. In parallel, frequency combs are perfect tools for high precision metrological applications and for quantum time transfer. Synchronously Pumped Optical Parametric Oscillators (SPOPOs) have been theoretically shown to produce multimode non-classical frequency combs. In this paper, we present the…
Low-noise lasers are of central importance in a wide variety of applications, including high spectral-efficiency coherent communication protocols, distributed fibre sensing, and long distance coherent LiDAR. In addition to low phase noise, frequency agility, that is, the ability to achieve high-bandwidth actuation of the laser frequency, is imperative for triangular chirping in frequency-modulated continuous-wave (FMCW) based ranging or any optical phase locking as routinely used in metrology. While integrated silicon-based lasers have experienced major advances and are now employed on a comme…
We present a nonlinear multimode superconducting electroacoustic system, where the interplay between superconducting kinetic inductance and piezoelectric strong coupling establishes an effective Kerr nonlinearity among multiple acoustic modes at 10 GHz that could hardly be achieved via intrinsic mechanical nonlinearity. By exciting this multimode Kerr system with a single microwave tone, we further demonstrate a coherent electroacoustic frequency comb and provide theoretical understanding of multimode nonlinear interaction in the superstrong coupling limit. This nonlinear superconducting elect…
A multimode microcavity sensor based on a self-interference microring resonator is demonstrated experimentally. The proposed multimode sensing method is implemented by recording wideband transmission spectra that consist of multiple resonant modes. It is different from the previous dissipative sensing scheme, which aims at measuring the transmission depth changes of a single resonant mode in a microcavity. Here, by combining the dissipative sensing mechanism and the machine learning algorithm, the multimode sensing information extracted from a broadband spectrum can be efficiently fused to est…
Low-loss photonic integrated circuits (PIC) and microresonators have enabled novel applications ranging from narrow-linewidth lasers, microwave photonics, to chip-scale optical frequency combs and quantum frequency conversion. To translate these results into a widespread technology, attaining ultralow optical losses with established foundry manufacturing is critical. Recent advances in fabrication of integrated Si3N4 photonics have shown that ultralow-loss, dispersion-engineered microresonators can be attained at die-level throughput. For emerging nonlinear applications such as integrated trav…
Adaptable, reconfigurable and programmable are key functionalities for the next generation of silicon-based photonic processors, neural and quantum networks. Phase change technology offers proven non-volatile electronic programmability, however the materials used to date have shown prohibitively high optical losses which are incompatible with integrated photonic platforms. Here, we demonstrate the capability of the previously unexplored material Sb$_2$Se$_3$ for ultralow-loss programmable silicon photonics. The favorable combination of large refractive index contrast and ultralow losses seen i…
Long-distance quantum communication through optical fibers is currently limited to a few hundreds of kilometres due to fiber losses. Quantum repeaters could extend this limit to continental distances. Most approaches to quantum repeaters require highly multimode quantum memories in order to reach high communication rates. The atomic frequency comb memory scheme can in principle achieve high temporal multimode storage, without sacrificing memory efficiency. However, previous demonstrations have been hampered by the difficulty of creating high-resolution atomic combs, which reduces the efficienc…
Optical I/O plays a crucial role in the lifespan of lab-on-a-chip systems, from preliminary testing to operation in the target environment. However, due to the precise alignments required, efficient and reliable fiber-to-chip connections remain challenging, yielding inconsistent test results and unstable packaged performance. To overcome this issue, for use in single mode on-chip systems, we propose the incorporation of area-enlarged grating couplers working in conjunction with multimode fibers. This combination enables simpler, faster, and more reliable connections than the traditional small …
The first demonstration of narrowband spectral filtering of multimode light on a 3D integrated photonic chip using photonic lanterns and waveguide Bragg gratings is reported. The photonic lanterns with multi-notch waveguide Bragg gratings were fabricated using the femtosecond direct-write technique in boro-aluminosilicate glass (Corning, Eagle 2000). Transmission dips of up to 5 dB were measured in both photonic lanterns and reference single-mode waveguides with 10.4-mm-long gratings. The result demonstrates efficient and symmetrical performance of each of the gratings in the photonic lantern.…
Lithium niobate is an excellent photonic material with large $χ^2$ and $χ^3$ nonlinearities. Recent breakthroughs in nanofabrication technology have enabled ultralow-loss nanophotonic devices based on a lithium-niobate-on-insulator (LNOI) platform. Here we present an overview of recent developments in the LNOI platform for on-chip optical frequency comb generation. These devices could lead to new opportunities for integrated nonlinear photonic devices for classical and quantum photonic applications.
The generation of dissipative Kerr solitons in optical microresonators has provided a route to compact frequency combs of high repetition rate, which have already been employed for optical frequency synthesizers, ultrafast ranging, coherent telecommunication and dual-comb spectroscopy. Silicon nitride (Si$_3$N$_4$) microresonators are promising for photonic integrated soliton microcombs. Yet to date, soliton formation in Si$_3$N$_4$ microresonators at electronically detectable repetition rates, typically less than 100 GHz, is hindered by the requirement of external power amplifiers, due to the…
Phonons offer the possibility to connect the microwave and optical domains while being efficiently transduced with electronic and optical signals. Here, we present a multimodal optomechanical platform, consisting of a mechanical-optical-mechanical resonator configuration. The mechanical modes, with frequencies at 265 MHz and 6.8 GHz, can be simultaneously excited into a phonon lasing regime as supported by a stability analysis of the system. Both the MHz and the GHz modes enter a self-sustained oscillation regime, leading to the intermodulation of two frequency combs in the optical field. We c…
Multimode receivers based on spatial or modal diversity are promising architectures to mitigate in real time the atmospheric turbulence effects for free space optical (FSO) communications. In this paper, we evaluate and comment on the dynamical communication performances of a FSO mode diversity receiver, based on a spatial demultiplexer and a silicon photonic coherent combiner, for an optical link from a GEO satellite to an optical ground station (OGS). We simulate time series of distorted wavefronts received by the OGS and we show numerically that the coherent combination of spatial modes mit…
Comb-enabled spectral-domain image transport through perturbation-prone multimode fibers
State Key Laboratory of Precision Spectroscopy, and Hainan Institute, East China Normal University（精密光谱学国家重点实验室及海南研究院，华东师范大学）；Chongqing Key Laboratory of Precision Optics, Chongqing Institute of East China Normal University（精密光学重庆市重点实验室，华东理工大学重庆研究院）；Jinan Institute of Quantum Technology（济南量子技术研究院）；Shanghai Research Center for Quantum Sciences（上海量子科学研究中心）
A method is proposed to experimentally determine principal modes for mode division multiplexing in a multimode optical fiber, i.e., increasing optical fiber information capacity via higher-order transverse eigenmodes. Principal modes are a special linear combination of eigenmodes that do not exhibit mode dispersion up to first order in frequency. This method is based on an SU(N) representation of mode dispersion whereby the generators of the corresponding SU(N) Lie algebra, i.e., generalized Gell-Mann matrices, predict higher-order Stokes parameters which can be used to measure principal modes…
Material characteristics and input-field specifics limit the controllability of nonlinear electromagnetic-field interactions. As these nonlinear interactions could be exploited to create strongly localized bright and dark waves, such as nonlinear surface polaritons, ameliorating this limitation is important. We present our approach to amelioration, which is based on a surface-polaritonic waveguide reconfiguration that enables excitation, propagation and coherent control of coupled dark rogue waves having orthogonal polarizations. Our control mechanism is achieved by finely tuning laser-field i…
The cavity electromechanical devices with radiation-pressure-interaction induced Kerr-like nonlinearity are promising candidates to generate microwave frequency combs. We construct a silicon-nitride-membrane-based superconducting cavity electromechanical device and study two mechanical modes mediated synergistic frequency combs. Around the threshold of intracavity field instability, we firstly show independent frequency combs with tooth spacing equalling to each mechanical mode frequency. At the overlap boundaries of these two individual mechanical mode mediated instability thresholds, we obse…
We propose a method to efficiently pump an excited mode of a multimode optical waveguide starting from a fundamental-mode input by combining Stark-Chirped Rapid Adiabatic Passage (SCRAP) and Supersymmetry (SUSY) transformations. In a two-waveguide set, we implement SCRAP by modulating the core refractive index of one waveguide, which is evanescently coupled to its SUSY partner. SCRAP provides an efficient transfer of light intensity between the modes of different waveguides, while SUSY allows to control which modes are supported. Using both techniques allows to achieve fidelities above 99% for…
We introduce a numerical procedure which permits to drastically accelerate the design of multimode photonic crystal resonators. Specifically, we demonstrate that the optical response of an important class of such nanoscale structures is reproduced accurately by a simple, one-dimensional model, within the entire spectral range of interest. This model can describe a variety of tapered photonic crystal structures. Orders of magnitude faster to solve, our approach can be used to optimize certain properties of the nanoscale cavity. Here we consider the case of a nanobeam cavity, where the confineme…
We demonstrate a convenient and fast method to measure the spectrally resolved far-fields of multimode terahertz quantum cascade lasers by combining a microbolometer focal plane array with an FTIR spectrometer. Far-fields of fundamental TM0 and higher lateral order TM1 modes of multimode Fabry-Pérot type lasers have been distinguished, which very well fit to the results obtained by a 3D finite-element simulation. Furthermore, multimode random laser cavities have been investigated, analyzing the contribution of each single laser mode to the total far-field. The presented method is thus an impor…
Inverse precoding algorithms in multimode fiber based communication networks are used to exploit mode dependent losses on the physical layer. This provides an asymmetry between legitimate (Bob) and unlegitimate (Eve) receiver of messages resulting in a significant SNR advantage for Bob. In combination with dynamic mode channel changes, Eve has no chance to reconstruct a sent message even in a worst case scenario in which she is almighty. This is the first time, Physical Layer Security in a fiber optical network is investigated on the basis of measured transmission matrices. These results show …
Mode-locking operation and multimode instabilities in Terahertz (THz) quantum cascade lasers (QCLs) have been intensively investigated during the last decade. These studies have unveiled a rich phenomenology, owing to the unique properties of these lasers, in particular their ultrafast gain medium. Thanks to this, in QCLs a modulation of the intracavity field intensity gives rise to a strong modulation of the population inversion, directly affecting the laser current. In this work we show that this property can be used to study the real-time dynamics of multimode THz QCLs, using a self-detecti…
Soliton microcombs -- phase-locked microcavity frequency combs -- have become the foundation of several classical technologies in integrated photonics, including spectroscopy, LiDAR, and optical computing. Despite the predicted multimode entanglement across the comb, experimental study of the quantum optics of the soliton microcomb has been elusive. In this work, we use second-order photon correlations to study the underlying quantum processes of soliton microcombs in an integrated silicon carbide microresonator. We show that a stable temporal lattice of solitons can isolate a multimode below-…
Quantum memory is a fundamental building block for large-scale quantum networks. On-demand optical storage with a large bandwidth, a high multimode capacity and an integrated structure simultaneously is crucial for practical application. However, this has not been demonstrated yet. Here, we fabricate an on-chip waveguide in a $\mathrm {^{151}Eu^{3+}:Y_2SiO_5}$ crystal with insertion losses of 0.2 dB, and propose a novel pumping scheme to enable spin-wave atomic frequency comb (AFC) storage with a bandwidth of 11 MHz inside the waveguide. Based on this, we demonstrate the storage of 200 tempora…
An ultralow-loss integrated photonic platform for discrete-variable quantum information processing
International Quantum Academy（国际量子科学院）；Shenzhen Futian SUSTech Institute for Quantum Technology and Engineering（深圳福田南方科技大学量子技术与工程研究院）；School of Physical Sciences and Hefei National Laboratory, University of Science and Technology of China（中国科学技术大学物理科学学院与合肥国家实验室）；Southern University of Science and Technology（南方科技大学）
The coupling of distinct systems underlies nearly all physical phenomena and their applications. A basic instance is that of interacting harmonic oscillators, which gives rise to, for example, the phonon eigenmodes in a crystal lattice. Particularly important are the interactions in hybrid quantum systems consisting of different kinds of degrees of freedom. These assemblies can combine the benefits of each in future quantum technologies. Here, we investigate a hybrid optomechanical system having three degrees of freedom, consisting of a microwave cavity and two micromechanical beams with close…
We analyze the properties of a Raman quantum light-atom interface in long atomic ensemble and its applications as a quantum memory or two-mode squeezed state generator. We consider the weak-coupling regime and include both Stokes and anti-Stokes scattering and the effects of Doppler broadening in buffer gas assuming frequent velocity-averaging collisions. We find the Green functions describing multimode transformation from input to output fields of photons and atomic excitations. Proper mode basis is found via singular value decomposition for short interaction times. It reveals that triples of…
