Reducing the operating temperature of normal conducting particle accelerators substantially increases their efficiency. Low-temperature operation increases the yield strength of the accelerator material and reduces surface resistance, hence a great reduction in cyclic fatigue could be achieved resulting in a large reduction in breakdown rates compared to room-temperature operation. Furthermore, temperature reduction increases the intrinsic quality factor of the accelerating cavities, and consequently, the shunt impedance leading to increased system efficiency and beam loading capabilities. In this paper, we present an experimental demonstration of the high-gradient operation of an X-band, 11.424 GHz, 20-cells linear accelerator (linac) operating at a liquid nitrogen temperature of 77 K. The tested linac was previously processed and tested at room temperature. We verified the enhanced accelerating parameters of the tested accelerator at cryogenic temperature using different measurements including electron beam acceleration up to a gradient of 150 MV/m, corresponding to a peak surface electric field of 375 MV/m. We also measured the breakdown rates in the tested structure showing a reduction of two orders of magnitude, x100, compared to their values at room temperature for the same accelerating gradient.
We report results of the experimental test of the High Temperature Superconductor based fast cycling prototype accelerator magnet capable to operate up to about 300 Tesla per second field ramping rate with some 0.5 T field in the magnet gap. The measured upper limit for the cryogenic cooling power required to support magnet conductor operation at high ramping rates indicates great potential for such types of magnets in rapid cycling synchrotrons for neutrino research or muon acceleration. The test magnet design, construction, and supporting cryogenic and power systems are briefly described. Th…
Since the introduction of the radio-frequency (rf) photoinjector electron source over thirty years ago, peak performance demands have dictated the use of high accelerating electric fields. With recent strong advances in obtainable field values, attendant increases in beam brightness are expected to be dramatic. In this article, we examine the implementation of very high gradient acceleration in a high frequency, cryogenic rf photoinjector. We discuss in detail the effects of introducing, through an optimized rf cavity shape, rich spatial harmonic content in the accelerating modes in this devic…
We report a surface treatment that systematically improves the quality factor of niobium radio frequency cavities beyond the expected limit for niobium. A combination of annealing in a partial pressure of nitrogen or argon gas and subsequent electropolishing of the niobium cavity surface leads to unprecedented low values of the microwave surface resistance, and an improvement in the efficiency of the accelerating structures up to a factor of 3, reducing the cryogenic load of superconducting cavities for both pulsed and continuous duty cycles. The field dependence of the surface resistance is r…
We have explored a concept for an advanced Normal-Conducting Radio-Frequency (NCRF) C-band linear accelerator (linac) structure to achieve a high gradient, high power e$^+$e$^-$ linear collider in the TeV class. This design study represents the first comprehensive investigation for an emerging class of distributed coupling accelerator topology exploring nominal cavity geometries, frequency and temperature of operation. The structure features internal manifolds for distributing RF power separately to each cell, permitting the full structure geometry to be designed for high shunt impedance and l…
The normal conducting Annular Coupled Structure (ACS) is applied for 190-400 MeV part of high intensity proton linac for the J-PARC. The ACS operating frequency is 972 MHz. The J-PARC ACS is strongly based on the results of previous investigations, especially results of Japan Hadron Project (JHP) research program in KEK. However, the design was revised and optimized to meet the requirements of reliability, operation efficiency and cost reduction. The cells shape of accelerating cells was optimized in total energy range to have high shunt impedance value together with the careful matching with …
We demonstrate practical accelerating gradients on a superconducting radiofrequency (SRF) accelerator cavity with cryocooler conduction cooling, a cooling technique that does not involve the complexities of the conventional liquid helium bath. A design is first presented that enables conduction cooling an elliptical-cell SRF cavity. Implementing this design, a single cell 650 MHz Nb3Sn cavity coupled using high purity aluminum thermal links to a 4 K pulse tube cryocooler generated accelerating gradients up to 6.6 MV/m at 100% duty cycle. The experiments were carried out with the cavity-cryocoo…
We have developed high-efficiency normal-conducting RF accelerating structures by combining H-mode resonator cavities and a transverse beam focusing by permanent-magnet quadrupoles (PMQ), for beam velocities in the range of a few percent of the speed of light. The shunt impedance of inter-digital H-mode (IH-PMQ) structures is 10-20 times higher than that of a conventional drift-tube linac, while the transverse size is 4-5 times smaller. Results of the combined 3-D modeling - electromagnetic computations, multi-particle beam-dynamics simulations with high currents, and thermal-stress analysis -…
There is a strong demand for accelerating structures able to achieve higher gradients and more compact dimensions for the next generation of linear accelerators for research, industrial and medical applications. In the framework of the Compact Light XLS project, an ultra high gradient higher harmonic RF accelerating structure is needed for the linearization of the longitudinal space phase. In order to determine the maximum sustainable gradients in normal conducting RF powered particle beam accelerators with extremely low probability of RF breakdown, investigations are in progress for using sho…
Travelling wave (TW) disk-loaded accelerating structure is one of the key components in normal conducting (NC) linear accelerators, and has been studied for many years. In the design process, usually after the dimensions of each cell and the two couplers are finalized, the structure is fabricated and tuned, and then the whole structure characteristics can be measured by the vector network analyzer. Before the structure fabrication, the whole structure characteristics are less simulated limited by the available computer capability. In this paper, we described the method to do the RF-thermal-str…
Ionization cooling is the preferred method for producing bright muon beams. This cooling technique requires the operation of normal conducting, radio-frequency (RF) accelerating cavities within the multi-tesla fields of DC solenoid magnets. Under these conditions, cavities exhibit increased susceptibility to RF breakdown, which can damage channel components and imposes limits on channel length and transmission efficiency. We present a solution to the problem of breakdown in strong magnetic fields. We report, for the first time, stable high-vacuum, copper cavity operation at gradients above 50 …
A high-current emittance-compensated RF photoinjector is a key enabling technology for a high-power CW FEL. A preliminary design of a normal-conducting, 2.5-cell pi-mode, 700-MHz CW RF photoinjector that will be built for demonstration purposes, is completed. This photoinjector will be capable of accelerating a 100-mA electron beam (3 nC per bunch at 35 MHz bunch repetition rate) to 2.7 MeV while providing an emittance below 7 mm-mrad at the wiggler. More than 1 MW of RF power will be fed into the photoinjector cavity through two ridge-loaded tapered waveguides. The waveguides are coupled to t…
Direct stroke measurement of Piezos for cavity frequency tuner of the ILC prototype cryomodule using a Laser Displacement Sensor
High Energy Accelerator Research Organization（高能加速器研究机构）；The Graduate University for Advanced Studies, Department of Accelerator Science, School of High Energy Accelerator Science, High Energy Accelerator Research Organization (KEK)（高级研究院高能加速器科学学部加速器科学系）
Superconducting radio-frequency (SRF) accelerating cavities are a promising technology for compact, high-power, MeV-scale accelerators, providing continuous beam operation for a wide range of potential applications in industry, medicine, national security, and science. However, SRF cavities have traditionally been cooled using complex and expensive cryogenic infrastructure, which has been a significant obstacle in employing this powerful technology in small-scale systems. With the recent progress on high-performance Nb$_3$Sn-coated SRF cavities and the introduction of cryocoolers, which can pr…
We report on an approach to produce quasi continuous-wave (cw) electron beams with an average beam current of milliamperes and a mean beam energy of a few MeV in a pulsed RF injector. Potential applications are in the planned laboratory astrophysics programs at DESY. The beam generation is based on field emission from a specially designed metallic field emitter. A quasi cw beam profile is formed over subsequent RF cycles at the resonance frequency of the gun cavity. This is realized by debunching in a cut disk structure accelerating cavity (booster) downstream of the gun. The peak and average …
This note presents optimization results for an injector with a super-conducting gun for the cw operation of the European XFEL, the corresponding start-to-end simulation calculations for the beam transport to the undulators and SASE calculations of the X-ray intensities for the achievable photon energies. The optimizations for an injector with a super-conducting gun are done mainly for an already experimentally shown accelerating gradient of 40 MV/m. Different working points with respect to transverse emittance and bunch length are chosen to see whether the lower transverse emittance of the lon…
