arXivDaily arXiv每日学术速递 周一至周五更新
arXiv周末暂无论文更新,休息一下吧,周末愉快~~
arXiv 2009.10560physics.app-phphysics.ins-detquant-ph
收藏

不同材料和热处理的七个几何形状相似的真空室的放气率比较

Outgassing rate comparison of seven geometrically similar vacuum chambers of different materials and heat treatments

James A. Fedchak, Julia K. Scherschligt, Sefer Avdiaj, Daniel S. Barker, Stephen P. Eckel, Ben Bowers, Scott OConnell, Perry Henderson

摘要:

我们测量了七个相同几何形状但由不同材料和热处理制成的真空室的水和氢的放气速率。测试了五种不同材料的腔室:304 L、316L和316LN不锈钢;钛(ASTM 2级);和6061铝。此外,由316L和316LN不锈钢构成的腔室经受真空烧制过程,其中它们在真空下加热至约950 °C持续24小时;这两个腔室被指定为316L-XHV和316LN-XHV。所有腔室具有相同的几何形状并且由相同的制造商制造,因此可以对这些腔室之间的放气速率进行相对比较。水脱气率作为时间的函数使用的吞吐量技术进行测量。316 L、316 LN、316 L-XHV、316 LN-XHV的水除气结果均相似,但在10^4 s时比304 L低3至5倍。Ti和Al腔室的水除气结果接近304 L的水除气结果,Ti稍低。使用上升速率法测量氢气除气速率,并在125 °C至150 °C的低温烘烤至少72小时后进行。Ti、Al、316 L-XHV和316 LN-XHV电离室的比释气速率都低于1 × 10^-11 Pa·L·s^-1·cm^-2,至少是304 L电离室的100倍或更高。304 L、316 L和316 LN真空室没有进行真空火焰热处理,其氢的释气速率比其他真空室大,比释气速率在4.0 X 10^-11 Pa·L ^-1·cm^-2和8.0 X 10^-11 Pa·L ^-1·cm^-2之间。我们得出结论,Ti,Al,316L-XHV和316LN-XHV具有氢除气率,使其成为超高真空(UHV)和极高真空(XHV)应用的绝佳选择,选择取决于成本和其他材料性能。

英文摘要:

We have measured the water and hydrogen outgassing rates of seven vacuum chambers of identical geometry but constructed of different materials and heat treatments. Chambers of five different materials were tested: 304L, 316L, and 316LN stainless steels; titanium (ASTM grade 2); and 6061 aluminum. In addition, chambers constructed of 316L and 316LN stainless steel were subjected to a vacuum-fire process, where they were heated to approximately 950 °C for 24 hours while under vacuum; these two chambers are designated as 316L-XHV and 316LN-XHV. All chambers were of identical geometry and made by the same manufacturer, thus a relative comparison of the outgassing rates among these chambers can be made. Water outgassing rates were measured as a function of time using the throughput technique. The water outgassing results for the 316L, 316LN, 316L-XHV, 316LN-XHV were all similar, but lower than those of 304L by a factor of 3 to 5 lower at 10^4 s. The water outgassing results for Ti and Al chambers were close to that of 304L, Ti being slightly lower. Hydrogen outgassing rates were measured using the rate-of-rise method and performed after a low-temperature bake of 125 °C to 150 °C for a minimum of 72 hours. The Ti, Al, 316L-XHV, and 316LN-XHV chambers all have specific outgassing rates below 1 X 10^-11 Pa L s^-1 cm^-2 and are at least a factor of 100 or better than the 304L chamber. The 304L, 316L, and 316LN chambers without vacuum-fire heat treatment have larger hydrogen outgassing rates than the other chambers, with specific outgassing rates ranging between 4.0 X 10^-11 Pa L s^-1 cm^-2 and 8.0 X 10^-11 Pa L s^-1 cm^-2. We conclude that Ti, Al, 316L-XHV, and 316LN-XHV have hydrogen outgassing rates that make them excellent choices for ultra-high vacuum (UHV) and extreme-high vacuum (XHV) applications, the choice depending on cost and other material properties.

机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。

↑