In this paper, we study the multiple-input and multiple-output (MIMO) wireless power transfer (WPT) system so as to enhance the output DC power of the rectennas. To that end, we revisit the rectenna nonlinearity considering multiple receive antennas. Two combining schemes for multiple rectennas at the receiver, DC and RF combinings, are modeled and analyzed. For DC combining, we optimize the transmit beamforming, adaptive to the channel state information (CSI), so as to maximize the total output DC power. For RF combining, we compute a closed-form solution of the optimal transmit and receive beamforming. In addition, we propose a practical RF combining circuit using RF phase shifter and RF power combiner and also optimize the analog receive beamforming adaptive to CSI. We also analytically derive the scaling laws of the output DC power as a function of the number of transmit and receive antennas. Those scaling laws confirm the benefits of using multiple antennas at the transmitter or receiver. They also highlight that RF combining significantly outperforms DC combining since it leverages the rectenna nonlinearity more efficiently. Two types of performance evaluations, based on the nonlinear rectenna model and based on realistic and accurate rectenna circuit simulations, are provided. The evaluations demonstrate that the output DC power can be linearly increased by using multiple rectennas at the receiver and that the relative gain of RF combining versus DC combining in terms of the output DC power level is very significant, of the order of 240% in a one-transmit antenna ten-receive antenna setup.
Hybrid Massive MIMO reduces implementation complexity but only supports beamforming coefficients that are common across all subbands. However, in macro cellular where the channel has limited degrees of freedom, the long-term component of the channel can be decomposed into a set of subband-independent beamforming basis functions referred to as eigenbeams. A Coherent Hybrid Massive MIMO system can form arbitrary linear combinations of the eigenbeams at every subband to mimic Digital Massive MIMO beamforming as observed across all locations in the cell.
Energy beamforming has emerged as a promising technique for enhancing the energy transfer efficiency of wireless power transfer (WPT). However, the performance of conventional energy beamforming may seriously degrade due to the non-linear radio frequency (RF) to direct current (DC) conversion at energy receivers (ERs). To tackle this issue, this letter proposes a new time-division energy beamforming, in which different energy beamforming matrices (of high ranks in general) are time shared to exploit the "convex-concave" shape of the RF-DC power relation at ERs. By considering a particular time…
Cognitive multiple-input multiple-output (MIMO) radar is capable of adjusting system parameters adaptively by sensing and learning in complex dynamic environment. Beamforming performance of MIMO radar is guided by both beamforming weight coefficients and the transceiver configuration. We propose a cognitive-driven MIMO array design where both the beamforming weights and the transceiver configuration are adaptively and concurrently optimized under different environmental conditions. The perception-action cycle involves data collection of full virtual array, covariance reconstruction and joint d…
In this paper, a novel robust beamforming scheme is proposed in three dimensional multi-input multi-output (3D-MIMO) systems. As one of the typical deployments of massive MIMO, a 3D-MIMO system owns sparse channels in angular domain. Thus, various of sparse channel estimation algorithms produce sparse channel estimation errors which can be utilized to narrow down the perturbation region of imperfect CSI. We investigate a $l_1$-norm bounded channel uncertainty model for the robust beamforming problems, which captures the sparse nature of channel errors. Compared with the conventional spherical …
Hybrid analog and digital beamforming has emerged as a key enabling technology for millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) communication systems since it can balance the trade-off between system performance and hardware efficiency. Owing to the strong ability of central control, cooperative networks show great potential to enhance the spectral efficiency of mmWave communications. In this paper, we consider cooperative mmWave MIMO systems and propose user association and hybrid beamforming design algorithms for three typical hybrid beamforming architectures. The c…
This letter develops an optimum beamforming method for downlink transmissions in cell-free massive multiple-input multiple-output (MIMO) systems, which employ a massive number of distributed access points to provide concurrent services to multiple users. The optimum design is formulated as a max-min problem that maximizes the minimum signal-to-interference-plus-noise ratio of all users. It is shown analytically that the problem is quasi-concave, and the optimum solution is obtained with the second-order cone programming. The proposed method identifies the best achievable beamforming performanc…
Beamforming is one of the key techniques in millimeter wave (mmWave) multi-input multi-output (MIMO) communications. Designing appropriate beamforming not only improves the quality and strength of the received signal, but also can help reduce the interference, consequently enhancing the data rate. In this paper, we propose a distributed multi-agent double deep Q-learning algorithm for beamforming in mmWave MIMO networks, where multiple base stations (BSs) can automatically and dynamically adjust their beams to serve multiple highly-mobile user equipments (UEs). In the analysis, largest receive…
This work proposes compact, flexible Multiple Input Multiple Output (MIMO) antennas. The design principle is based on the excitation of different orthogonal radiating modes within the same antenna volume. Via phase control of the excited modes, beamforming is demonstrated in azimuth and elevation planes using single-layered structures. For flexibility, the antennas are designed using Polydimethylsiloxane (PDMS) as the substrate. Numerical results demonstrate that isolation better than 23 dB is realized in all investigated antennas under different bend configurations. Moreover, the proposed tec…
Hybrid beamforming is considered a key enabler to realize millimeter wave (mmWave) multiple-input multiple-output (MIMO) communications due to its capability of considerably reducing the number of costly and power-hungry radio frequency chains in the transceiver. However, in mmWave MIMO orthogonal frequency-division multiplexing (MIMO-OFDM) systems, hybrid beamforming design is challenging because the analog precoder and combiner are required to be shared across the whole employed bandwidth. In this paper, we propose closed-form solutions to the problem of designing the analog precoder/combine…
Sparse array design aided by emerging fast sensor switching technologies can lower the overall system overhead by reducing the number of expensive transceiver chains. In this paper, we examine the active sparse array design enabling the maximum signal to interference plus noise ratio (MaxSINR) beamforming at the MIMO radar receiver. The proposed approach entails an entwined design, i.e., jointly selecting the optimum transmit and receive sensor locations for accomplishing MaxSINR receive beamforming. Specifically, we consider a co-located multiple-input multiple-output (MIMO) radar platform wi…
This letter investigates a multiple-input multiple-output (MIMO) wireless power transfer (WPT) system under practical non-liner energy harvesting (EH) models. We propose a new generic energy receiver (ER) architecture consisting of $N$ receive antennas and $L$ rectifiers, for which one power splitter is inserted after each antenna to adaptively split the received radio frequency (RF) signals among the $L$ rectifiers for efficient non-linear RF-to-direct current (DC) conversion. With the proposed architecture, we maximize the total harvested DC power at the ER, by jointly optimizing the transmi…
Hybrid beamforming has evolved as a promising technology that offers the balance between system performance and design complexity in mmWave MIMO systems. Existing hybrid beamforming methods either impose unit-modulus constraints or a codebook constraint on the analog precoders/combiners, which in turn results in a performance-overhead tradeoff. This paper puts forth a tensor framework to handle the wideband hybrid beamforming problem, with Vandermonde constraints on the analog precoders/combiners. The proposed method strikes the balance between performance, overhead and complexity. Numerical r…
In this letter, we investigate the millimeter wave (mmWave) downlink multiuser multiple-input multiple-output (MU-MIMO) system, adopting the dynamic subarray architecture at the base station and considering the multi-stream communication for each user. Aiming at maximizing the system spectral efficiency, we propose a novel hybrid beamforming design. First, assuming no inter-user interference (IUI), we easily get the optimal fully-digital beamformers and combiners using the singular value decomposition of each user channel and the waterfilling algorithm. Then, based on the obtained fullydigital…
In this paper, we propose an energy-efficient radar beampattern design framework for a Millimeter Wave (mmWave) massive multi-input multi-output (mMIMO) system, equipped with a hybrid analog-digital (HAD) beamforming structure. Aiming to reduce the power consumption and hardware cost of the mMIMO system, we employ a machine learning approach to synthesize the probing beampattern based on a small number of RF chains and antennas. By leveraging a combination of softmax neural networks, the proposed solution is able to achieve a desirable beampattern with high accuracy.
In this paper, we propose a beamforming design for dual-functional radar-communication (DFRC) systems at the millimeter wave (mmWave) band, where hybrid beamforming and sub-arrayed MIMO radar techniques are jointly exploited. We assume that a base station (BS) is serving a user equipment (UE) located in a Non-Line-of-Sight (NLoS) channel, which in the meantime actively detects multiple targets located in a Line-of-Sight (LoS) channel. Given the optimal communication beamformer and the desired radar beampattern, we propose to design the analog and digital beamformers under non-convex constant-m…
In this paper, we study a multi-sine multiple-input multiple-output (MIMO) wireless power transfer (WPT) system with the objective to increase the output DC power. We jointly optimize the multi-sine waveform and beamforming accounting for the rectenna nonlinearity, and consider two combining schemes for the rectennas at the receiver, namely DC and RF combinings. For DC combining, the waveform and transmit beamforming are optimized, as a function of the channel state information (CSI). For RF combining, the optimal transmit and receive beamformings are provided in closed form and the waveform i…
In this paper, we consider a dual-hop Multiple Input Multiple Output (MIMO) wireless multi-relay network, in which a source-destination pair both equipped with multiple antennas communicates through multiple half-duplex amplify-and-forward (AF) relay terminals which are also with multiple antennas. Since perfect channel state information (CSI) is difficult to obtain in practical multi-relay network, we consider imperfect CSI for all channels. We focus on maximizing the signal-to-interference-plus-noise ratio (SINR) at the destination. We propose a novel robust linear beamforming at the relays,…
Beamforming gain is a key ingredient in the performance of LEO satellite communication systems to be integrated into cellular networks. However, beam codebooks previously designed in the context of MIMO communication for terrestrial networks, do not provide the appropriate performance in terms of inter-beam interference and gain stability as the satellite moves. In this paper, we propose a dynamic codebook that provides a stable gain during the period of time that the satellite covers a given cell, while avoiding link retraining and extra calculation as the satellite moves. In addition, the pr…
Massive MIMO is currently a leading physical layer technology candidate that can dramatically enhance throughput in 5G systems, for both unicast and multicast transmission modalities. As antenna elements are becoming smaller and cheaper in the mmW range compared to radio frequency (RF) chains, it is crucial to perform antenna selection at the transmitter, such that the available RF chains are switched to an appropriate subset of antennas. This paper considers the joint problem of multicast beamforming and antenna selection for a single multicast group in massive MIMO systems. The prior state-o…
Intelligent reflecting surfaces (IRSs) constitute passive devices, which are capable of adjusting the phase shifts of their reflected signals, and hence they are suitable for passive beamforming. In this paper, we conceive their design with the active beamforming action of multiple-input multipleoutput (MIMO) systems used at the access points (APs) for improving the beamforming gain, where both the APs and users are equipped with multiple antennas. Firstly, we decouple the optimization problem and design the active beamforming for a given IRS configuration. Then we transform the optimization p…
In this paper, outage probability (OP) of a joint transmit and receive antenna selection (JTRAS) scheme is analyzed in multiple-input multiple-output non orthogonal multiple access based downlink energy harvesting (EH) relaying networks. In this dual-hop and amplify-and-forward relaying based network, since the first and second hops are types of single-user and multi-user systems, respectively, the optimal JTRAS and suboptimal majority-based JTRAS schemes are employed in the first and second hops. The theoretical OP analysis is carried out over Nakagami-m fading channels in the cases of perfec…
Hybrid analog and digital beamforming (HBF) has been recognized as an attractive technique offering a tradeoff between hardware implementation limitation and system performance for future broadband millimeter wave (mmWave) communications. In contrast to most current works focusing on the HBF design for orthogonal frequency division multiplexing based mmWave systems, this paper investigates the HBF design for single carrier (SC) systems due to the advantage of low peak-to-average power ratio in transmissions. By applying the alternating minimization method, we propose an efficient HBF scheme ba…
Designing beamforming techniques for the downlink (DL) of frequency division duplex (FDD) massive MIMO is known to be a challenging problem due to the difficulty of obtaining channel state information (CSI). Indeed, since the uplink-downlink bands are disjoint, the system cannot rely on channel reciprocity to estimate the channel from uplink (UL) pilots as in time division duplexing (TDD) system. Still, in this paper, we propose original designs for robust beamformers that do not require any feedback from the users and only rely on the transmission of UL pilots. The price to pay is that the be…
Future wireless communication systems are expected to explore spectral bands typically used by radar systems, in order to overcome spectrum congestion of traditional communication bands. Since in many applications radar and communication share the same platform, spectrum sharing can be facilitated by joint design as dual function radar-communications system. In this paper, we propose a joint transmit beamforming model for a dual-function multiple-input-multiple-output (MIMO) radar and multiuser MIMO communication transmitter sharing the spectrum and an antenna array. The proposed dual-function…
In this letter, we consider optimal hybrid beamforming design to minimize the transmission power under individual signal-to-interference-plus-noise ratio (SINR) constraints in a multiuser massive multiple-input-multiple-output (MIMO) system. This results in a challenging non-convex optimization problem. We consider two cases. In the case where the number of users is smaller than or equal to that of radio frequency (RF) chains, we propose a low-complexity method to obtain a globally optimal solution and show that it achieves the same transmission power as an optimal fully-digital beamformer. In…
Hybrid beamforming (HB) has emerged as a promising technology to support ultra high transmission capacity and with low complexity for Millimeter Wave (mmWave) multiple-input and multiple-output (MIMO) system. However, the design of digital and analog beamformer is a challenge task with non-convex optimization, especially for the multi-user scenario. Recently, the blooming of deep learning research provides a new vision for the signal processing of communication system. In this work, we propose a deep neural network based HB for the multi-User mmWave massive MIMO system, referred as DNHB. The H…
Over-the-air computation (AirComp) has been recognized as a promising technique in Internet-of-Things (IoT) networks for fast data aggregation from a large number of wireless devices. However, as the number of devices becomes large, the computational accuracy of AirComp would seriously degrade due to the vanishing signal-to-noise ratio (SNR). To address this issue, we exploit the massive multiple-input multiple-output (MIMO) with hybrid beamforming, in order to enhance the computational accuracy of AirComp in a cost-effective manner. In particular, we consider the scenario with a large number …
Multiple-input multiple-output (MIMO) systems exploit spatial diversity to facilitate multi-user communications with high spectral efficiency by beamforming. As MIMO systems utilize multiple antennas and radio frequency (RF) chains, they are typically costly to implement and consume high power. A common method to reduce the cost of MIMO receivers is utilizing less RF chains than antennas by employing hybrid analog/digital beamforming (HBF). However, the added analog circuitry involves active components whose consumed power may surpass that saved in RF chain reduction. An additional method to r…
Federated learning (FL) is recognized as a key enabling technology to support distributed artificial intelligence (AI) services in future 6G. By supporting decentralized data training and collaborative model training among devices, FL inherently tames privacy leakage and reduces transmission costs. Whereas, the performance of the wireless FL is typically restricted by the communication latency. Multiple-input multiple-output (MIMO) technique is one promising solution to build up a communication-efficient edge FL system with limited radio resources. In this paper, we propose a novel joint devic…
This work proposes an electrically small 3D beamforming antenna for PHYsical Layer (PHY-layer) security. The antenna comprises two layers of stacked patch structures and is a five-mode five-port MIMO system operating around 1.85 GHz with electrical size ${ka=0.98}$ and radiation efficiency of up to ${55\%}$. By studying the properties of the excited modes, phase and amplitude control allow for unidirectional beam scanning towards any direction around the elevation and azimuth planes. PHY-layer security is investigated using the directional modulation (DM) technique, which transmits unscrambled…
To satisfy the capacity requirements of future mobile systems, under-utilized millimeter wave frequencies can be efficiently exploited by employing massive MIMO technology with highly directive beamforming. Hybrid analog-digital beamforming has been recognised as a promising approach for large-scale MIMO implementations with a reduced number of costly and power-hungry RF chains. In comparison to fully connected architecture, hybrid beamforming (HBF) with partially connected RF architecture is particularly appealing for the practical implementation due to less complex RF power division and comb…
This paper jointly designs linear precoding (LP) and codebook-based beamforming implemented in a satellite with massive multiple-input multiple-output (mMIMO) antenna technology. The codebook of beamforming weights is built using the columns of the discrete Fourier transform (DFT) matrix, and the resulting joint design maximizes the achievable throughput under limited transmission power. The corresponding optimization problem is first formulated as a mixed integer non-linear programming (MINP). To adequately address this challenging problem, an efficient LP and DFT-based beamforming algorithm …
This paper considers a lens antenna array-assisted millimeter wave (mmWave) multiuser multiple-input multiple-output (MU-MIMO) system. The base station's beam selection matrix and user terminals' phase-only beamformers are jointly designed with the aim of maximizing the uplink sum rate. In order to deal with the formulated mixed-integer optimization problem, a penalty dual decomposition (PDD)-based iterative algorithm is developed via capitalizing on the weighted minimum mean square error (WMMSE), block coordinate descent (BCD), and minorization-maximization (MM) techniques. Moreover, a low-co…
Massive multiple-input multiple-output (MIMO) is an important technology in fifth generation (5G) cellular networks and beyond. To help design the beamforming at the base station, 5G has introduced new support in the form of flexible feedback and configurable antenna array geometries. In this article, we present an overview of MIMO throughout the mobile standards, highlight the new beam-based feedback system in 5G NR, and describe how this feedback system enables massive MIMO through beam management. Finally, we conclude with challenges related to massive MIMO in 5G.
Terahertz (THz) communications with a frequency band $0.1-10$ THz are envisioned as a promising solution to future high-speed wireless communication. Although with tens of gigahertz available bandwidth, THz signals suffer from severe free-spreading loss and molecular-absorption loss, which limit the wireless transmission distance. To compensate for the propagation loss, the ultra-massive multiple-input-multiple-output (UM-MIMO) can be applied to generate a high-gain directional beam by beamforming technologies. In this paper, a review of beamforming technologies for THz UM-MIMO systems is prov…
The ever-evolving internet of things (IoT) has led to the growth of numerous wireless sensors, communicating through the internet infrastructure. When designing a network using these sensors, one critical aspect is the longevity and self-sustainability of these devices. For extending the lifetime of these sensors, radio frequency energy harvesting (RFEH) technology has proved to be promising. In this paper, we propose CURE, a novel framework for RFEH that effectively combines the benefits of cell-free massive MIMO (CFmMIMO), unmanned aerial vehicles (UAVs), and reconfigurable intelligent surfa…
Cell-free massive MIMO (CF-mMIMO) systems represent a promising approach to increase the spectral efficiency of wireless communication systems. However, near-optimal beamforming solutions require a large amount of signaling exchange between access points (APs) and the network controller (NC). In this letter, we propose two unsupervised deep neural networks (DNN) architectures, fully and partially distributed, that can perform decentralized coordinated beamforming with zero or limited communication overhead between APs and NC, for both fully digital and hybrid precoding. The proposed DNNs achie…
