We investigate dynamic fracture of heterogeneous materials experimentally by measuring displacement fields as a rupture propagates through a periodic array of obstacles of controlled fracture energy. Our measurements demonstrate the applicability of the classical equation of motion of cracks at a discontinuity of fracture energy: the crack speed jumps at the entrance and exit of an obstacle, as predicted by the crack-tip energy balance within the brittle fracture framework. The speed jump amplitude is governed by the fracture energy contrast and by the combination of rate-dependency of fracture energy and inertia of the medium, which allows the crack to cross a fracture energy discontinuity at constant energy release rate. This discontinuous dynamics and the rate-dependence cause higher effective toughness, which governs the coarse-grained behavior of these cracks.
Three dimensional calculations of ductile crack growth under mode I plane strain, small scale yielding conditions are carried out using an elastic-viscoplastic constitutive relation for a progres- sively cavitating plastic solid with two populations of void nucleating second phase particles. Full field solutions are obtained for three dimensional material microstructures characterized by ran- dom distributions of void nucleating particles. Crack growth resistance curves and fracture surface roughness statistics are calculated using standard procedures. The range of void nucleating particle vol…
Understanding the fracture toughness (resistance) of glasses is a fundamental problem of prime theoretical and practical importance. Here we theoretically study its dependence on the loading rate, the age (history) of the glass and the notch radius $ρ$. Reduced-dimensionality analysis suggests that the notch fracture toughness results from a competition between the initial, age- and history-dependent, plastic relaxation timescale $τ^{pl}_0$ and an effective loading timescale $τ^{ext}(\dot{K}_I,ρ)$, where $\dot{K}_I$ is the tensile stress-intensity-factor rate. The toughness is predicted to sca…
Fracture in a disordered lattice system is studied. In our system, particles are initially arranged on the triangular lattice and each nearest-neighbor pair is connected with a randomly chosen soft or hard Hookean spring. Every spring has the common threshold of stress at which it is cut. We make an initial crack and expand the system perpendicularly to the crack. We find that the maximum stress in the stress-strain curve is larger than those in the systems with soft or hard springs only (uniform systems). Energy required to advance fracture is also larger in some disordered systems, which ind…
Entanglement of polymer chains is ubiquitous in elastomers, gels, and biological tissues. While the effects of chain entanglement on elasticity and viscoelasticity of polymer networks have been intensively studied, it remains elusive how chain entanglement affects fracture and fatigue of polymer networks. In this paper, using polyacrylamide hydrogels as a model material, we systematically compare fracture toughness and fatigue threshold of polymer networks with various levels of chain entanglement. We find that the fracture toughness and fatigue threshold of an unentangled polymer network are …
Brittle materials fail catastrophically. In consequence of their limited flaw-tolerance, failure occurs by localized fracture and is typically a dynamic process. Recently, experiments on epithelial cell monolayers have revealed that this scenario can be significantly modified when the material susceptible to cracking is adhered to a hydrogel substrate. Thanks to the hydraulic coupling between the brittle layer and the poroelastic substrate, such a composite can develop a toughening mechanism that relies on the simultaneous growth of multiple cracks. Here, we study this remarkable behaviour by …
Hydrogels have the ability to undergo large deformations and yet fail like brittle materials. The development of biocompatible hydrogels with high strength and toughness is an ongoing challenge in many applications. We crosslinked bovine gelatin using glutaraldehyde (control) and methylglyoxal (MGO) and assessed changes in their fracture toughness. Swelling experiments show ~710% retention of water in MGO hydrogels as compared to ~450% in control specimens. We used FTIR to identify the presence of chemical groups that may be involved in the crosslinking of gelatin gels. Scanning electron micro…
Using Brownian dynamics, we simulate the fracture of polymer interfaces reinforced by diblock connector chains. We find that for short chains the interface fracture toughness depends linearly on the degree of polymerization $N$ of the connector chains, while for longer chains the dependence becomes $N^{3/2}$. Based on the geometry of initial chain configuration, we propose a scaling argument that accounts for both short and long chain limits and crossover between them.
We combine molecular dynamics simulations of deformations at the submicron scale with a continuum fracture mechanics calculation for the onset of crack propagation to predict the macroscopic fracture toughness of amorphous glassy polymers. Key ingredients in this multiscale approach are the elastic properties of polymer crazes and the stress at which craze fibrils fail through chain pullout or scission. Our results are in quantitative agreement with dimensionless ratios that describe experimental polymers and their variation with temperature, polymer length and polymer rigidity.
In this work we investigate the Orowan hypothesis, that decreases in surface energy due to surface adsorbates lead directly to lowered fracture toughness, at an atomic/molecular level. We employ a Lennard-Jones system with a slit crack and an infiltrating fluid, nominally with gold-water properties, and explore steric effects by varying the soft radius of fluid particles and the influence of surface energy/hydrophobicity via the solid-fluid binding energy. Using previously developed methods, we employ the J-integral to quantify the sensitivity of fracture toughness to the influence of the flui…
We examine how shell geometry affects fracture. As suggested by previous results and our own phase-field simulations, shell shape dramatically affects crack evolution and the effective toughness of the shell structure. To gain insight and eventually develop new concepts for optimizing the design of thin shell structures, we derive the configurational force conjugate to crack extension for Koiter's linear thin shell theory. We identify the conservative contribution to this force through an Eshelby tensor, as well as non-conservative contributions arising from curvature.
Here, we report measurements of detailed dynamic cohesive properties (DCPs) beyond the dynamic fracture toughness of a bicontinuously nanostructured copolymer, polyurea, under an extremely loading rate, from deep-learning analyses of a dynamic big-data-generating experiment. We first describe a new Dynamic Line-Image Shearing Interferometer (DL-ISI), which uses a streak camera to record optical fringes of displacement-gradient vs time profile along a line on sample's rear surface. This system enables us to detect crack initiation and growth processes in plate-impact experiments. Then, we prese…
In our previous paper (Eur. Phys. J. E 4, 121 (2001)) we proposed a coarse-grained elastic energy for nacre, or stratified structure of hard and soft layers. We then analyzed a crack running perpendicular to the layers and suggested one possible reason for the enhanced toughness of this substance. In the present paper, we consider a crack running parallel to the layers. We propose a new term added to the previous elastic energy, which is associated with the bending of layers. We show that there are two regimes for the parallel-fracture solution of this elastic energy; near the fracture tip the…
Soft materials including elastomers and gels are pervasive in biological systems and technological applications. Whereas it is known that intrinsic fracture energies of soft materials are relatively low, how the intrinsic fracture energy cooperates with mechanical dissipation in process zone to give high fracture toughness of soft materials is not well understood. In addition, it is still challenging to predict fracture energies and crack-tip strain fields of soft tough materials. Here, we report a scaling theory that accounts for synergistic effects of intrinsic fracture energies and dissipat…
Molecular-dynamics simulations of fracture in metallic glass-like systems are observed to undergo embrittlement due to a small change in interatomic potential. This change in fracture toughness, however, is not accompanied by a corresponding change in flow stress. Theories of brittle fracture proposed by Freund and Hutchinson indicate that strain rate sensitivity is the controling physical parameter in these cases. A recent theory of viscoplasticity in this class of solids by Falk and Langer further suggests that the change in strain rate sensitivity corresponds to a change in the susceptibili…
Soft yet tough materials are ubiquitous in nature and everyday life. The ratio between fracture toughness and intrinsic fracture energy of a soft material defines its toughness enhancement. Soft materials' toughness enhancement has been long attributed to their bulk stress-stretch hysteresis induced by dissipation mechanisms such as Mullins effect and viscoelasticity. With a combination of experiments and theory, here we show that the bulk dissipation mechanisms significantly underestimate the toughness enhancement of soft tough materials. We propose a new mechanism and scaling law to account …
Based on spatial-temporal resolved measurements of the stress field at crack tip based on polarized optical microscopy (str-POM), the stress analysis approach to elastomeric fracture uncovers new insights. We show new phenomenology in contrast to the standard description of linear elastic fracture mechanics (LEFM). First, str-POM measurements show emergence of a stress saturation zone whose dimension r_ss is independent of the stress intensity factor K. This elastic zone is plastic zone whose size would scale quadratically with K. The absence of stress divergence allows us to measure tip stres…
Sacrificial bonds and hidden length in structural molecules account for the greatly increased fracture toughness of biological materials compared to synthetic materials without such structural features, by providing a molecular-scale mechanism for energy dissipation. One example is in the polymeric glue connection between collagen fibrils in animal bone. In this paper, we propose a simple kinetic model that describes the breakage of sacrificial bonds and the release of hidden length, based on Bell's theory. We postulate a master equation governing the rates of bond breakage and formation. This…
We explore the Mode I fracture toughness of a polymer gel containing a semi-infinite, growing crack. First, an expression is derived for the energy release rate within the linearized, small-strain setting. This expression reveals a crack tip velocity-independent toughening that stems from the poroelastic nature of polymer gels. Then, we establish a poroelastic cohesive zone model that allows us to describe the micromechanics of fracture in gels by identifying the role of solvent pressure in promoting poroelastic toughening. We evaluate the enhancement in the effective fracture toughness throug…
The fundamental problem of friction in the presence of macroscopic adhesion, as in soft bodies, is receiving interest from many experimentalists. Since the first fracture mechanics `purely brittle' model of Savkoor and Briggs, models have been proposed where the mixed mode toughness is interpreted with phenomenological fitting coefficients introducing weaker coupling between modes than expected by the "purely brittle" model. We compare here two such previously proposed models and introduce a third one to show that the transition to sliding is very sensitive to the form of the mixed-mode model.…
Experimental and theoretical observations have agreed that the onset of cavitation in soft materials requires higher tensile pressure than pure water. The extra tensile pressure is required since the cavitating bubble needs to overcome the elastic energy in soft materials. In this manuscript, we have developed two models to study and quantify the extra tensile pressure. In the first approach, we proposed a strain energy based random fiber network (RFN) failure criteria in which interaction between the cavitating bubble and RFN is considered. Gelatin samples are prepared for different concentra…
We study experimentally the fracture mechanisms of a model cohesive granular medium consisting of glass beads held together by solidified polymer bridges. The elastic response of this material can be controlled by changing the cross-linking of the polymer phase, for example. Here we show that its fracture toughness can be tuned over an order of magnitude by adjusting the stiffness and size of the polymer bridges. We extract a well-defined fracture energy from fracture testing under a range of material preparations. This energy is found to scale linearly with the cross-sectional area of the bri…
Understanding the fracture toughness of glasses is of prime importance for science and technology. We study it here using extensive atomistic simulations in which the interaction potential, glass transition cooling rate and loading geometry are systematically varied, mimicking a broad range of experimentally accessible properties. Glasses' nonequilibrium mechanical disorder is quantified through $A_{\rm g}$, the dimensionless prefactor of the universal spectrum of nonphononic excitations, which measures the abundance of soft glassy defects that affect plastic deformability. We show that while …
Sacrificial bonds and hidden length (SBHL) in structural molecules provide a mechanism for energy dissipation at the nanoscale. It is hypothesized that their presence leads to greater fracture toughness than what is observed in materials without such features. Here, we investigate this hypothesis using a simplified model of a mineralized collagen fibril sliding on a polymeric interface with SBHL systems. A 1D coarse-grained nonlinear spring-mass system is used to model the fibril. Rate-and-displacement constitutive equations are used to describe the mechanical properties of the polymeric syste…
We study the dynamics of proppants carried by fluid driven into an evolving penny-shaped fracture. The behaviour of the slurry flow is investigated in two phases: pressurised injection and elastic closure. During injection the slurry is modelled using a frictional rheology that takes into account the shear-induced migration and jamming of the proppants. Making pragmatic assumptions of negligible toughness and cross-fracture fluid slip, we find self-similar solutions supporting a range of proppant concentration profiles. In particular, we define an effective viscosity, which equates the fractur…
