Chemical doping is one of the most important strategies for tuning electrical properties of semiconductors, particularly thermoelectric materials. Generally, the main role of chemical doping lies in optimizing the carrier concentration, but there can potentially be other important effects. Here, we show that chemical doping plays multiple roles for both electron and phonon transport properties in half-Heusler thermoelectric materials. With ZrNiSn-based half-Heusler materials as an example, we use high-quality single and polycrystalline crystals, various probes, including electrical transport measurements, inelastic neutron scattering measurement, and first-principles calculations, to investigate the underlying electron-phonon interaction. We find that chemical doping brings strong screening effects to ionized impurities, grain boundary, and polar optical phonon scattering, but has negligible influence on lattice thermal conductivity. Furthermore, it is possible to establish a carrier scattering phase diagram, which can be used to select reasonable strategies for optimization of the thermoelectric performance.
Determining defect types and concentrations remains a big challenge of semiconductor materials science. By using ab-initio thermal conductivity calculations we reveal that Ni/vacancy antisites, and not the previously claimed Sn/Zr antisites, are the dominant defects affecting thermal transport in half-Heusler compound ZrNiSn. Our calculations correctly predict the thermal conductivity dependence with temperature and concentration, in quantitative agreement with published experimental results. Furthermore, we find a characteristic proportionality between phonon-antisite scattering rates and the…
ZrNiSn and related half Heusler compounds are candidate materials for efficient thermoelectric energy conversion with a reported thermoelectric figure-of-merit of n-type ZrNiSn exceeding unity. Progress on p-type materials has been more limited, which has been attributed to the presence of an impurity band, possibly related to the presence of Ni interstitials in nominally vacant 4d position. The specific energetic position of this band, however, has not been resolved. Here, we report results of a concerted theory-experiment investigation for a nominally undoped ZrNiSn, based on measurements of…
There is an increasing reckoning that the thermoelectric performance of a material is dependent on its microstructure. However, the microstructure-properties relationship often remains elusive, in part due to the complexity of the hierarchy and scales of features that influence transport properties. Here, we focus on the promising Heusler-Fe2VAl compound. We directly correlate microstructure and local properties, using advanced scanning electron microscopy methods including in-situ four-point-probe technique for electron transport measurements. The local thermal conductivity is investigated by…
Thermoelectric figures of merit, ZT > 0.5, have been obtained in arc-melted TiNiSn-based ingots. This promising conversion efficiency is due to a low lattice thermal conductivity, which is attributed to excess nickel in the half-Heusler structure.
Half-Heusler alloys such as the (Zr,Hf)NiSn intermetallic compounds are important thermoelectric materials for converting waste heat into electricity. Reduced electrical resistivity at the hot interface between the half-Heusler material and a metal contact is critical for device performance, however this has yet to be achieved in practice. Recent experimental work suggests that a coherent interface between half-Heusler and full-Heusler compounds can form due to diffusion of transition metal atoms into the vacant sublattice of the half-Heusler lattice. We study theoretically the structural and …
Improvements in the thermoelectric properties of Half-Heusler materials have been achieved by means of a micrometer-scale phase separation that increases the phonon scattering and reduces the lattice thermal conductivity. A detailed study of the p-type Half-Heusler compounds Ti(1-x)Hf(x)CoSb0.85Sn0.15 using high-resolution synchrotron powder X-ray diffraction and element mapping electron microscopy evidences the outstanding thermoelectric properties of this system. A combination of intrinsic phase separation and adjustment of the carrier concentration via Sn substitution is used to realize a r…
The discovery of Heusler alloys has revolutionized the research field of intermetallics due to the ease with which one can derive potential candidates for multifunctional applications. During recent years, many half Heusler alloys have been investigated for their thermoelectric properties. The f electron based rare earth ternary half Heusler compound DyPdBi has its f energy levels located close to the Fermi energy level. Other research efforts have emphasized that such materials have good thermoelectric capabilities. We have explored using first principles the electronic band structure of DyPd…
The electronic and transport properties of the half-Heusler compound LaPtSb are investigated by performing first-principles calculations combined with semi-classical Boltzmann theory and deformation potential theory. Compared with many typical half-Heusler compounds, the LaPtSb exhibits obviously larger power factor at room temperature, especially for the n-type system. Together with the very low lattice thermal conductivity, the thermoelectric figure of merit (ZT) of LaPtSb can be optimized to a record high value of 2.2 by fine tuning the carrier concentration.
Thermoelectricity is a promising avenue for harvesting energy but large-scale applications are still hampered by the lack of highly-efficient low-cost materials. Recently, Fe$_2YZ$ Heusler compounds were predicted theoretically to be interesting candidates with large thermoelectric power factor. Here, we show that under doping conditions compatible with thermoelectric applications, these materials are prone to an unexpected magnetic instability detrimental to their thermoelectric performance. We rationalize the physics at the origin of this instability, provide guidelines for avoiding it and d…
Half-Heusler compounds usually exhibit relatively higher lattice thermal conductivity that is undesirable for thermoelectric applications. Here we demonstrate by first-principles calculations and Boltzmann transport theory that the BiBaK system is an exception, which has rather low thermal conductivity as evidenced by very small phonon group velocity and relaxation time. Detailed analysis indicates that the heavy Bi and Ba atoms form a cage-like structure, inside which the light K atom rattles with larger atomic displacement parameters. In combination with its good electronic transport propert…
Half-Heusler alloys (MgAgSb structure) are promising thermoelectric materials. RNiSn half-Heusler phases (R=Hf, Zr, Ti) are the most studied in view of their thermal stability. The highest dimensionless figure of merit (ZT) obtained is ~1 in the temperature range ~450-900oC, primarily achieved in nanostructured alloys. Through proper annealing, ZT~1.2 has been obtained in a previous ZT~1 n-type (Hf,Zr)NiSn phase without the nanostructure. There is an appreciable increase in the power factor, decrease in charge carrier density, and increase in carrier mobility. The findings are attributed to th…
We have performed systematic density functional calculations and evaluated thermoelectric properties, See- beck coefficient and anomalous Nernst coefficient of half-Heusler comounds CoMSb(M=Sc, Ti, V, Cr, and Mn). The carrier concentration dependence of Seebeck coefficients in nonmagnetic compounds are in good agreement with experimental values. We found that the half-metallic ferromagnetic CoMnSb show large anomalous Nernst effect originating from Berry curvature at the Brillouin zone boundary. These results help to understanding for the mechanism of large anomalous Nernst coefficient and giv…
In order to improve the thermoelectric performance of TiCoSb we have substituted 50% of Ti equally with Zr and Hf at Ti site and Sb with Sn and Se equally at Sb site. The electronic structure of Ti0.5Zr0.25Hf0.25CoSn0.5Se0.5 is investigated using the full potential linearized augmented plane wave method and the thermoelectric transport properties are calculated on the basis of semi-classical Boltzmann transport theory. Our band structure calculations show that Ti0.5Zr0.25Hf0.25CoSn0.5Se0.5 has semiconducting behavior with indirect band gap value of 0.98 eV which follow the empirical rule of 18…
Intermetallic semiconductors with the cubic Half-Heusler structure (XYZ) have excellent thermoelectric properties. This has been attributed to the high degeneracy of the carrier pockets in the band structure, but large differences are found between different material compositions. Half-Heuslers are often interpreted within Zintl chemistry, making a clear distinction between an electropositive cation ($X^{n+}$) and an extended polyanion ($YZ^{n-}$). Based on quantitative real space chemical bonding analysis, we unravel large degrees of covalent bonding between the formal cation and anion, makin…
Half-Heusler compounds (space group Fm3m) has garnered increasing attention in recent years in the thermoelectric community. Three decades ago, refractory RNiSn half-Heusler compounds (R represents refractory metals such as Hf, Zr, Ti) were found to be narrow-gap semiconductors with large Seebeck coefficients in 100s of micro-volt per Kelvin. Today, half-Heusler (HH) compounds have emerged as promising thermoelectric materials in the intermediate temperature range (400-800oC). HH materials are endowed with good thermal stability and scalability. Thermoelectric n-p modules based on HH materials…
Half-Heusler phases have gained recently much interest as thermoelectric materials. Screening of possible systems was performed by ab-initio simulation using VASP-software. The energy-versus-Volume (E(V)) curves were calculated and calibrated. For TiCoSb, NbNiSn, FeMoSb the stability of Half-Heusler phase against concurrent crystal structures like TiNiSi, ZrCoAl, ZrBeSi, FeSiV, ZrNiP and Full Heusler was confirmed. However, the thermo-dynamical driving force as calculated from the difference in lattice energies is less than 0.1eV/atom. Hence, the fabrication of Half Heusler phases is a challen…
The electronic structure and thermoelectric properties of ZrRuTe-based Half-Heusler compounds are studied using density functional theory (DFT) and Boltzmann transport formalism. Based on rigorous computations of electron relaxation time $τ$ considering electron-phonon interactions and lattice thermal conductivity $κ_l$ considering phonon-phonon interactions, we find ZrRuTe to be an intrinsically good thermoelectric material. It has a high power factor of $\sim 2\times 10^{-3}$ W/m-K$^{2}$ and low $κ_l\sim 10$ W/m-K at 800 K. The thermoelectric figure of merit $ZT \sim 0.13$ at 800 K is higher…
Half-Heusler and Heusler compounds have been of great interest for several decades for thermoelectric, magnetic, half-metallic and many other interesting properties. Among these systems, Zr-Ni-Sn compounds are interesting thermoelectrics which can go from semiconducting half-Heusler (HH) limit, ZrNiSn, to metallic Heusler (FH) limit, ZrNi$_2$Sn. Recently Makogo et al. [J. Am. Chem. Soc. 133, 18843 (2011)] found that dramatic improvement in the thermoelectric power factor of HH can be achieved by putting excess Ni into the system. This was attributed to an energy filtering mechanism due to the …
We report on the high-temperature (350 K <T< 1000 K) thermoelectric properties of the ternary compounds LuNiSb (cubic) and LuNiSn (orthorhombic) and a composite material (LuNiSb)$_{0.5}$(LuNiSn)$_{0.5}$. The electrical conductivity in LuNiSn is metallic, while it is semiconducting-like in LuNiSb. The Seebeck coefficient reaches -5.5 $μ$V/K at 700 K for the former compound and 66 $μ$V/K at 607 K for the latter one. The composite sample (LuNiSb)$_{0.5}$(LuNiSn)$_{0.5}$ constructed from orthorhombic matrix with cubic inclusions combines the electrical conductivity of LuNiSn with the thermoelectri…
Half-Heusler phases (space group F43m, C1b) have recently captured much attention as promising thermoelectric materials for heat-to-electric power conversion in the mid-to-high temperature range. The most studied ones are the RNiSn-type half-Heusler compounds, where R represents refractory metals Hf, Zr, and Ti. These compounds have shown a high-power factor and high-power density, as well as good material stability and scalability. Due to their high thermal conductivity, however, the dimensionless figure of merit (zT) of these materials has stagnated near 1 for a long time. Since 2013, the ve…
A half-Heusler material FeNb$_{0.8}$Ti$_{0.2}$Sb has been identified as a promising thermoelectric material due to its excellent thermoelectric performance at high temperatures. The origins of the efficient thermoelectric performance are investigated through a series of low-temperature (2 - 400 K) measurements. The high data coherence of the low and high temperatures is observed. An optimal and nearly temperature-independent carrier concentration is identified, which is ideal for the power factor. The obtained single type of hole carrier is also beneficial to the large Seebeck coefficient. The…
Half-Heusler (HH) alloys have attracted considerable interest as promising thermoelectric (TE) materials in the temperature range around 700 K and above, which is close to the temperature range of most industrial waste heat sources. The past few years have seen nanostructuing play an important role in significantly enhancing the TE performance of several HH alloys. In this article, we briefly review the recent progress and advances in these HH nanocomposites. We begin by presenting the structure of HH alloys and the different strategies that have been utilized for improving the TE properties o…
To understand the unexpectedly high thermoelectric performance observed in the thin-film Heusler alloy Fe$_2$V$_{0.8}$W$_{0.2}$Al, we study the magnon drag effect, generated by the tungsten based impurity band, as a possible source of this enhancement, in analogy to the phonon drag observed in FeSb$_2$. Assuming that the thin-film Heusler alloy has a conduction band integrating with the impurity band, originated by the tungsten substitution, we derive the electrical conductivity $L_{11}$ based on the self-consistent t-matrix approximation and the thermoelectric conductivity $L_{12}$ due to mag…
We investigate electronic structures and thermoelectric properties of recent synthetic half-Heusler $\mathrm{ZrNiPb}$ by using generalized gradient approximation (GGA) and GGA plus spin-orbit coupling (GGA+SOC). Calculated results show that $\mathrm{ZrNiPb}$ is a indirect-gap semiconductor. Within the constant scattering time approximation, semi-classic transport coefficients are performed through solving Boltzmann transport equations. It is found that the SOC has more obvious influence on power factor in p-type doping than in n-type doping, leading to a detrimental effect in p-type doping. Th…
A series of full-Heusler alloys, $\rm Fe_2V_{1-x}W_xAl$, $0 \leq x \leq 0.2$, was prepared, characterized and relevant physical properties to account for the thermoelectric performance were studied in a wide temperature range. Additionally, off-stoichiometric samples with similar compositions have been included, and a 10~\% improvement of the thermoelectric figure of merit was obtained. The V/W substitution causes i) a change of the main carrier type, from holes to electrons as evidenced from Seebeck and Hall measurements and ii) a substantial reduction of the lattice thermal conductivity due …
We investigated six heavy element bismuth-based 18-VEC half-Heusler alloys CoTiBi, CoZrBi, CoHfBi, FeVBi, FeNbBi, and FeTaBi by first principles approach, in search of better thermoelectric prospects. The motivation is driven by expected lower thermal conductivity and the recent discovery of CoZrBi-based materials. Significantly, our calculated power factor values of all the systems show an increment of $\sim$40\% in comparison to the reported \textit{p}-type CoTiSb. We propose that doping at Bi-site, on account of electronic features, will be helpful in achieving the proposed power factor val…
Utilizing a material in thermoelectric applications requires a mechanical, thermal, and lattice stability as well a high figure of merit (ZT). In this work, we present the structural, electronic, magnetic, mechanical, thermodynamic, dynamic, and thermoelectric properties of CoFeYGe (Y = Ti, Cr) quaternary Heusler compounds using the density functional theory (DFT). The calculated mechanical properties and phonon dispersions reveal that the structures of these compounds are stable. Both CoFeCrGe and CoFeTiGe compounds show a ferromagnetic and ferrimagnetic half-metallic behavior with band gaps …
Polycrystalline samples of Er$_{1-x}$Ho$_x$NiSb ($x$ = 0, 0.2, 0.3, 0.5, 0.7, 0.8, 1) were characterized by means of x-ray powder diffraction (XRD), scanning electron microscopy (SEM), and optical metallography. The results proved the formation of half-Heusler alloys in the entire composition range. Their electrical transport properties (resistivity, thermoelectric power) were studied in the temperature interval 350-1000 K. The measured electrical resistivity spanned between 5 and 25 $μΩ$m. The maximum thermopower of 50-65 $μ$V/K was observed at temperatures 500-650 K. Replacing Ho for Er resu…
High lattice thermal conductivity in half-Heusler alloys has been the major bottleneck in thermoelectric applications. Disordered half-Heusler alloys could be a plausible alternative to this predicament. In this paper, utilizing first-principles simulations, we have demonstrated the low lattice thermal conductivity in two such phases, NbFe$_{0.5}$Ni$_{0.5}$Sn and TaFe$_{0.5}$Ni$_{0.5}$Sn, in comparison to well-known half-Heusler alloy TiCoSb. We trace the low thermal conductivity to their short phonon lifetime, originating from the interaction among acoustic and low-lying optical phonons. We r…
Half-Heuslers, an emerging thermoelectric material group, has complex bandstructures with multiple bands that can be aligned through band engineering approaches, giving us an opportunity to improve their power factor. In this work, going beyond the constant relaxation time approximation, we perform an investigation of the benefits of band alignment in improving the thermoelectric power factor under different density of states dependent scattering scenarios. As a test case we consider the Co-based p-type half-Heuslers TiCoSb, NbCoSn and ZrCoSb. First, using simplified effective mass models comb…
By using ab initio electronic structure calculations here we report the three new full Heusler alloys which are possessing very good thermoelectric behavior and expected to be synthesized in the laboratories. These are Fe2 ScP, Fe2 ScAs and Fe2 ScSb compound. First two compounds are indirect band gap semiconductors and the last one shows semimetallic ground state. The value of band gap of Fe2 ScP and Fe2 ScAs is 0.3 and 0.09 eV, respectively. These compounds show the presence of flat conduction bands along Γ - X-direction suggesting for the large electron like effective mass and promising for …
On the basis of density functional theory and semi-classical Boltzmann theory, we have investigated the structural, elastic, electronic, optical and thermoelectric properties of 18--valence electron count rhodium based half-Heusler alloys focusing on RhTiP, RhTiAs, RhTiSb, and RhTiBi. The absence of imaginary frequencies in the phonon dispersion curve for these system verifies that they are structurally stable. RhTiP is ductile in nature, while others are brittle. The alloys are found to be semiconducting with indirect band gaps ranging from 0.94 to 1.01 eV. Our calculations suggest these mate…
Materials design based on first-principles electronic calculations has proven a fruitful strategy to identify new thermoelectric materials with a favorable figure of merit. Recent electronic structure calculations predict that in cobalt-based half-Heusler systems a power factor higher than in CoTiSb can be achieved upon p-type doping of CoVSn, CoNbSn, CoTaSn, CoMoIn, and CoWIn. Here, using a first-principles approach and semi-classical Boltzmann transport theory, we investigate the electrical and thermal transport properties of these materials. The calculated thermal conductivity at room tempe…
We have performed a comprehensive set of first principles calculations to study the structural, elastic, electronic, magnetic and transport properties of new quaternary Heusler compounds CoZrMnX (X =Al, Ga, Ge, In). The results showed that all the quaternary Heusler compounds were stable in Type(I) structure. CoZrMnX are elastically stable and relatively hard materials. CoZrMnAl, CoZrMnGa, and CoZrMnIn are found to be ductile and CoZrMnGe is brittle in nature. The calculated Debye temperatures of all compounds are relatively high. The electronic structure calculations reveal that CoZrMnAl is n…
First principle study of electronic, magnetic and thermoelectric properties of Co$_2$YPb (Y = Tc, Ti, Zr and Hf) full Heusler: Application to embedded automotive systems
Half-Heusler alloys have been one of the benchmark high temperature thermoelectric materials owing to their thermal stability and promising figure of merit ZT. Simonson et al. early showed that small amounts of vanadium doped in Hf0.75Zr0.25NiSn enhanced the Seebeck coefficient and correlated the change with the increased density of states near the Fermi level. We herein report a systematic study on the role of vanadium (V), niobium (Nb), and tantalum (Ta) as prospective resonant dopants in enhancing the ZT of n-type half-Heusler alloys based on Hf0.6Zr0.4NiSn0.995Sb0.005. The V doping was fou…
We have explored the mechanical, electronic, optical and thermoelectric properties of p-type half-Heusler compound BaAgP for the first time using density functional theory based calculations. The mechanical and dynamical stability of this compound is confirmed by studying the Born stability criteria and phonon dispersion curve, respectively. It is soft, ductile and elastically anisotropic. The atomic bonding along a-axis is stronger than that along c-axis. The calculated electronic structure reveals that the studied compound is an indirect band gap semiconductor. The analysis of charge density…
Structural, electronic, and transport properties of ScNiSb, ScPdSb, and ScPtSb were investigated from first principles. Electronic band structures derived within the fully relativistic MBJLDA approach were compared with those obtained from the standard GGA calculations. All the compounds studied exhibit indirect narrow band gaps (0.24-0.63 eV). The effective masses of hole-like carriers are relatively small (0.27-0.36), and decrease with an increasing atomic number of the transition metal component. The carrier relaxation time, required for realistic calculations of the electrical conductivity…
We report $^{59}$Co, $^{93}$Nb, and $^{121}$Sb nuclear magnetic resonance (NMR) measurements combined with density functional theory (DFT) calculations on a series of half-Heusler semiconductors, including NbCoSn, ZrCoSb, TaFeSb and NbFeSb, to better understand their electronic properties and general composition-dependent trends. These materials are of interest as potentially high efficiency thermoelectric materials. Compared to the other materials, we find that ZrCoSb tends to have a relatively large amount of local disorder, apparently antisite defects. This contributes to a small excitation…
Half-Heusler compounds have emerged as promising thermoelectric materials that offer huge compositional space to tune their thermoelectric performance. A class of stable half Heusler compounds formed from elements of three specific groups in the periodic table viz. X$_{p}$X$'_{1-p}$Y$_{q}$Y$'_{1-q}$Z$_{r}$Z$'_{1-r}$ (with X, X$'$= Ti, Zr, Hf, Y, Y$'$ = Ni, Pd, Pt and Z, Z$'$ = Ge, Sn, Pb and p, q, r = 0, 0.25, 0.75 and 1) via various stoichiometric isoelectronic elemental substitution at the X, Y and Z sites respectively is investigated. Intelligent filters are employed at each step of our hig…
Half-Heusler (HH) phases (space group F43m, Clb) are increasingly gaining attention as promising thermoelectric materials in view of their thermal stability, scalability, and environmental benignity as well as efficient power output. Until recently, the verifiable dimensionless figure of merit (ZT) of HH phases has remained moderate near 1, which limits the power conversion efficiency of these materials. We report herein ZT~1.3 in n-type (Hf,Zr)NiSn alloys near 850 K developed through elemental substitution and simultaneously embedment of nanoparticles in the HH matrix, obtained by annealing t…
We explore the structural, electronic, mechanical and thermoelectric properties of a new half Heusler compound, HfPtPb which is all metallic heavy element and has been recently been proposed to be stable [Nature Chem 7 (2015) 308]. In the present work, we employ density functional theory and semiclassical Boltzmann transport equations with constant relaxation time approximation. The mechanical properties such as Shear modulus, Young modulus, elastic constants, Poisson ratio, and shear anisotropy factor are investigated. The elastic and phonon properties reveal that this compound is mechanicall…
Half-Heusler (HH) phases have garnered much attention as thermally stable and non-toxic thermoelectric materials for power conversion. The most studied alloys to date utilize Hf, Zr, and Ti as the base components. These alloys can achieve a moderate dimensionless figure of merit, ZT, near 1. Recent studies have advanced the thermoelectric performance of HH alloys by employing nanostructures and novel compositions to achieve larger ZT, reaching as high as 1.5. Herein, we report that traditional alloying techniques applied to the conventional HfZr-based half-Heusler alloys can also lead to excep…
Calculations using density functional theory (DFT) were performed to investigate the structural, dynamical, mechanical, electronic, magnetic, and thermoelectric properties of VTiRhZ (Z = Al, Ga, In) alloys. The most stable structure of these alloys was found to be the type-I configuration. Using GGA-PBE functional, VTiRhGa, and VTiRhIn alloys are predicted as half-metallic ferromagnets with a 100% spin-polarization and a total magnetic moment of 3μB, which is promising for spintronic applications. The thermoelectric properties and lattice thermal conductivity of VTiRhZ alloys were obtained usi…
Science-driven design of future thermoelectric materials requires a deep understanding of the fundamental relationships between microstructure and transport properties. Grain boundaries in polycrystalline materials influence the thermoelectric performance through the scattering of phonons or the trapping of electrons due to space-charge effects. Yet, the current lack of careful investigations on grain boundary-associated features hinders further optimization of properties. Here, we study n-type NbCo1-xPtxSn half-Heusler alloys, which were synthesized by ball milling and spark plasma sintering …
The microscopic physics behind the lattice thermal conductivity of NiTiSn is investigated using first-principles-based anharmonic lattice dynamics. The calcu lated lattice thermal conductivity of bulk materials (5.3 W/m.K) is in good agreement with the experimental value at the optimal working temper ature (700 K), but is overestimated below this temperature. The calculated values can be strongly affected by the size of the crystalline grains. We show tha t the lattice thermal conductivity is dominated by the acoustic (transverse and mostly longitudinal) modes with no contribution from the opt…
