As a means to control wireless propagation environments, the use of emerging and novel intelligent reflecting surfaces (IRS) is envisioned to enhance and broaden many applications in future wireless networks. This paper is concerned with a point-to-point IRS-assisted millimeter-wave (mmWave) system in which the IRS consists of multiple subsurfaces, each having the same number of passive reflecting elements, whereas both the transmitter and receiver are equipped with massive antenna arrays. Under the scenario of having very large numbers of antennas at both transmit and receive ends, the achievable rate of the system is derived. Furthermore, with the objective of maximizing the achievable rate, the paper presents optimal solutions of power allocation, precoding/combining, and IRS's phase shifts. Then it is shown that when the number of reflecting elements at each subsurface is very large, the number of favorable and controllable propagation paths provided by the IRS is simply equal to the number of subsurfaces while the received signal-to-noise ratio corresponding to each of the favorable paths increases quadratically with the number of reflecting elements. In addition, the problem of minimizing the transmit power subject to the rate constraint is analyzed for the scenario without direct paths in the pure LOS propagation. Finally, numerical results are provided to corroborate the obtained analysis.
In mmWave massive multiple-input multiple-output (mMIMO) systems, hybrid digital/analog beamforming has been recognized as an economic means to overcome the severe mmWave propagation loss. To facilitate beamforming for mmWace mMIMO, there is a great urgency to acquire accurate channel state information. To this end, a novel doubly-sparse approach is proposed to estimate doubly-selective mmWave channels under hybrid mMIMO. Via the judiciously designed training pattern, the well-known beamspace sparsity along with the under-investigated delay-domain sparsity that mmWave channels exhibit can be j…
Recently, intelligent reflecting surface (IRS) assisted mmWave networks are emerging, which bear the potential to address the blockage issue of the millimeter wave (mmWave) communication in a more cost-effective way. In particular, IRS is built by passive and programmable electromagnetic elements that can manipulate the mmWave propagation channel into a more favorable condition that is free of blockage via judicious joint BS-IRS transmission design. However, the coexistence of IRSs and mmWave BSs complicates the network architecture, and thus poses great challenges for efficient beam managemen…
In this paper, we study the high-resolution channel estimation problem for intelligent reflecting surface (IRS)-assisted millimeter wave (mmWave) multiple-input-multiple-output (MIMO) communications, which is a prerequisite to guarantee further high-rate data transmission. Considering the typical sparsity of mmWave channels, we formulate the cascaded channel estimation problem from a sparse signal recovery perspective, and then propose a novel two-step cascaded channel estimation protocol to estimate the cascaded user-IRS-base station channel with high-resolution for IRS-assisted mmWave MIMO c…
Millimeter-wave (mmWave) communications provide access to spectra with bandwidths and in abundance. However, the high susceptibility of mmWave to blockage imposes crucial challenges, especially to low-latency services. In this paper, a novel intelligent reflecting surface (IRS) assisted mmWave scheme is proposed to overcome the impact of blockage. New methods are developed to minimize the user power for a multi-user mmWave system by jointly optimizing individual device power, multi-user detection matrix and passive beamforming, subject to delay requirements. An alternating optimization framewo…
In this letter, secure beamforming in a multiple intelligent reflecting surfaces (IRSs)-aided millimeter-wave (mmWave) system is investigated. In this system, the secrecy rate is maximized by controlling the on-off status of each IRS as well as optimizing the phase shift matrix of the IRSs. This problem is posed as a joint optimization problem of transmit beamforming and IRS control, whose goal is to maximize the secrecy rate under the total transmission power and unit-modulus constraints. The problem is difficult to solve optimally due to the nonconvexity of constraint conditions and coupled …
In this paper, we focus on the sum-rate optimization in a multi-user millimeter-wave (mmWave) system with distributed intelligent reflecting surfaces (D-IRSs), where a base station (BS) communicates with users via multiple IRSs. The BS transmit beamforming, IRS switch vector, and phase shifts of the IRS are jointly optimized to maximize the sum-rate under minimum user rate, unit-modulus, and transmit power constraints. To solve the resulting non-convex optimization problem, we develop an efficient alternating optimization (AO) algorithm. Specifically, the non-convex problem is converted into t…
Millimeter wave (mmWave) communications are evolving as a promising technology to meet the ever increasing data rate requirements. However, high directivity and severe path loss make it vulnerable to blockages, which could be frequent in indoor or urban environments. To address this issue, intelligent reflecting surfaces (IRSs) are introduced to provide additional adjustable reflected paths. Most prior works assume that elements of IRSs have an infinite phase resolution, which is difficult to be realized in practical systems. In this paper, IRSs with low-resolution phase shifters are considere…
Millimeter wave (MmWave) communications is capable of supporting multi-gigabit wireless access thanks to its abundant spectrum resource. However, the severe path loss and high directivity make it vulnerable to blockage events, which can be frequent in indoor and dense urban environments. To address this issue, in this paper, we introduce intelligent reflecting surface (IRS) as a new technology to provide effective reflected paths to enhance coverage of mmWave signals. In this framework, we study joint active and passive precoding design for IRS-assisted mmWave systems, where multiple IRSs are …
As communication systems that employ millimeter wave (mmWave) frequency bands must use large antenna arrays to overcome the severe propagation loss of mmWave signals, hybrid beamforming has been considered as an integral component of mmWave communications. Recently, intelligent reflecting surface (IRS) has been proposed as an innovative technology that can significantly improve the performance of mmWave communication systems through the use of low-cost passive reflecting elements. In this paper, we study IRS-aided mmWave multiple-input multiple-output (MIMO) systems with hybrid beamforming arc…
Intelligent reflecting surface (IRS) is envisioned as a promising solution for controlling radio propagation environments in future wireless systems. In this paper, we propose a distributed intelligent reflecting surface (IRS) assisted multi-user millimeter wave (mmWave) system, where IRSs are exploited to enhance the mmWave signal coverage when direct links between base station and users are unavailable. First, a joint active and passive beamforming problem is established for weighted sum-rate maximization. Then, an alternating iterative algorithm with closed-form expressions is proposed to t…
In this paper, we consider channel estimation for intelligent reflecting surface (IRS)-assisted millimeter wave (mmWave) systems, where an IRS is deployed to assist the data transmission from the base station (BS) to a user. It is shown that for the purpose of joint active and passive beamforming, the knowledge of a large-size cascade channel matrix needs to be acquired. To reduce the training overhead, the inherent sparsity in mmWave channels is exploited. By utilizing properties of Katri-Rao and Kronecker products, we find a sparse representation of the cascade channel and convert cascade ch…
This letter focuses on the secure transmission for an intelligent reflecting surface (IRS)-assisted millimeter-wave (mmWave) and terahertz (THz) systems, in which a base station (BS) communicates with its destination via an IRS, in the presence of a passive eavesdropper. To maximize the system secrecy rate, the transmit beamforming at the BS and the reflecting matrix at the IRS are jointly optimized with transmit power and discrete phase-shift constraints. It is first proved that the beamforming design is independent of the phase shift design under the rank-one channel assumption. The formulat…
Beijing Institute of Technology（北京理工大学）；CNRS（法国国家科学研究中心）；CentraleSupélec（中央理工-高等电力学院）；Université Paris-Saclay（巴黎-萨克雷大学）；King Abdullah University of Science and Technology（阿卜杜拉国王科技大学）
Integrating large intelligent reflecting surfaces (IRS) into millimeter-wave (mmWave) massive multi-input-multi-ouput (MIMO) has been a promising approach for improved coverage and throughput. Most existing work assumes the ideal channel estimation, which can be challenging due to the high-dimensional cascaded MIMO channels and passive reflecting elements. Therefore, this paper proposes a deep denoising neural network assisted compressive channel estimation for mmWave IRS systems to reduce the training overhead. Specifically, we first introduce a hybrid passive/active IRS architecture, where v…
The opening of the millimeter wave (mmWave) spectrum bands for 5G communications has motivated the need for novel spectrum sharing solutions at these high frequencies. In fact, reconfigurable intelligent surfaces (RISs) have recently emerged to enable spectrum sharing while enhancing the incumbents' quality-of-service (QoS). Nonetheless, co-existence over mmWave bands remains persistently challenging due to their unfavorable propagation characteristics. Hence, initiating mmWave spectrum sharing requires the RIS to further assist in improving the QoS over mmWave bands without jeopardizing spect…
In this letter, we investigate the robust and secure beamforming (RSBF) in an intelligent reflecting surface (IRS) aided millimeter wave (mmWave) multiple input single output (MISO) system, where multiple single antenna eavesdroppers (Eves) are arbitrarily distributed nearby the legitimate receiver. Considering the channel state information (CSI) of Eves' channels is imperfectly known at the legitimate transmitter, the RSBF design problems to maximize the worst case of achievable secrecy rate (ASR) are formulated under the total transmission power and unit-modulus constraints. Since the proble…
This work investigates the effect of double intelligent reflecting surface (IRS) in improving the spectrum efficient of multi-user multiple-input multiple-output (MIMO) network operating in the millimeter wave (mmWave) band. Specifically, we aim to solve a weighted sum rate maximization problem by jointly optimizing the digital precoding at the transmitter and the analog phase shifters at the IRS, subject to the minimum achievable rate constraint. To facilitate the design of an efficient solution, we first reformulate the original problem into a tractable one by exploiting the majorization-min…
Intelligent reflecting surfaces (IRSs) are regarded as promising enablers for future millimeter wave (mmWave) wireless communication, due to their ability to create favorable line-of-sight (LoS) propagation environments. In this paper, we investigate channel estimation in downlink IRS-assisted mmWave multiple-input multiple-output (MIMO) systems. By leveraging the sparsity of mmWave channels, we formulate the channel estimation problem as a fixed-rank constrained non-convex optimization problem. To tackle the non-convexity, an efficient algorithm is proposed by capitalizing on alternating mini…
The use of millimeter waves for wireless communications is one of the main technological innovations of 5G systems with respect to previous generations of cellular systems. Their consideration, however, has been up to now mainly restricted to the case in which analog or, at most, hybrid analog-digital beamforming structures were used, thus posing a limitation on the multiplexing capabilities and peak data rates that could be theoretically achieved at these frequencies. Recent progress in the field of electronics, however, has made the energy consumption of digital beamforming structures at lea…
Millimeter wave (mmWave) is a practical solution to provide high data rate for the vehicle-to-everything (V2X) communications. This enables the future autonomous vehicles to exchange big data with the base stations (BSs) such as the velocity and the location to improve the awareness of the advanced driving assistance system (ADAS). In this context, we consider a single-cell multiuser doubly-selective system wherein the BS simultaneously serves multiple vehicles. To accomplish this requirement, the BS is implemented in hybrid architecture to support multiple spatial streams while the vehicles h…
In this paper, a downlink intelligent reflecting surface (IRS) enhanced millimeter-wave (mmWave) non-orthogonal multiple access (NOMA) system is considered. A joint optimization problem over active beamforming, passive beamforming and power allocation is formulated. Due to the highly coupled variables, the formulated optimization problem is non-convex. To solve this problem, an alternative optimization and successive convex approximation based iterative algorithm is proposed. Numerical results illustrate that: 1) the proposed scheme offers significant sum-rate gains, which confirms the effecti…
This letter focuses on the non-convex joint optimization with a dynamic resource of multi-user for an intelligent reflecting surface-enhanced mmWave system, where all users are concentrated on the unique cluster beam. Firstly, the objective function of the above non-linear problem is converted into a quadratic programming form under the quality of service constraints. Further, a multi-blocks alternating optimization framework with dynamic power allocation is proposed to obtain the maximum sum-rate, where the relaxed ADMM algorithm is adopted to tackle the optimal fulldigital precoder and the c…
In this paper, we derive the uplink achievable rate expression of intelligent reflecting surface (IRS)-aided millimeter-wave (mmWave) systems, taking into account the phase noise at IRS and the quantization error at base stations (BSs). We show that the performance is limited only by the resolution of analog-digital converters (ADCs) at BSs when the number of IRS reflectors grows without bound. On the other hand, if BSs have ideal ADCs, the performance loss caused by IRS phase noise is a constant. Finally, our results validate the feasibility of using low-precision hardware at the IRS when BSs…
In this paper, we present a novel mobile user tracking (UT) scheme for codebook-based intelligent reflecting surface (IRS) aided millimeter wave (mmWave) systems. The proposed UT scheme exploits the temporal correlation of the direction from the IRS to the mobile user for selecting IRS phase shifts that provide reflection towards the user. To this end, the user's direction is periodically estimated based on a generalized likelihood ratio test (GLRT) and the user's movement trajectory is extrapolated from several past direction estimates. The efficiency of the proposed UT scheme is evaluated in…
We investigate the use of an intelligent reflecting surface (IRS) in a millimeter-wave (mmWave) vehicular communication network. An intelligent reflecting surface consists of passive elements, which can reflect the incoming signals with adjustable phase shifts. By properly tuning the phase shifts we can improve link performance. This is known as phase optimization or passive beamforming. We consider the problem of rate maximization in the uplink, which utilizes an IRS. However, using an IRS brings more challenges in terms of channel estimation. We propose two schemes to reduce the channel esti…
A fundamental challenge in millimeter-wave (mmWave) communication is the susceptibility to blocking objects. One way to alleviate this problem is the use of reconfigurable intelligent surfaces (RIS). Nevertheless, due to the large number of passive reflecting elements on RIS, channel estimation turns out to be a challenging task. In this paper, we address the channel estimation for RIS-aided mmWave communication systems based on a localization method. The proposed idea consists of exploiting the sparsity of the mmWave channel and the topology of the RIS. In particular, we first propose the con…
Intelligent reflecting surface (IRS) offers a cost effective solution to link blockage problem in mmWave communications, and the prerequisite of which is the accurate estimation of (1) the optimal beams for base station/access point (BS/AP) and mobile terminal (MT), (2) the optimal reflection patterns for IRSs, and (3) link blockage. In this paper, we carry out beam training design for IRSs assisted mmWave communications to estimate the aforementioned parameters. To acquire the optimal beams and reflection patterns, we firstly perform random beamforming and maximum likelihood estimation to est…
Intelligent reflecting surface (IRS) has been considered as a promising technology to alleviate the blockage effect and enhance coverage in millimeter wave (mmWave) communication. To explore the impact of IRS on the performance of mmWave communication, we investigate a multi-IRS assisted mmWave communication network and formulate a sum rate maximization problem by jointly optimizing the active and passive beamforming and the set of IRSs for assistance. The optimization problem is intractable due to the lack of convexity of the objective function and the binary nature of the IRS selection varia…
In this letter, we optimize the channel estimator of the cascaded channel in an intelligent reflecting surface (IRS)-assisted millimeter wave (mmWave) multi-antenna system. In this system, the receiver is equipped with a hybrid architecture adopting quantized beamforming. Different from traditional multiple-input multiple-output (MIMO) systems, the design of channel estimation is challenging since the IRS is usually a passive array with limited signal processing capability. We derive the optimized channel estimator in a closed form by reformulating the problem of cascaded channel estimation in…
We consider the problem of downlink channel estimation for intelligent reflecting surface (IRS)-assisted millimeter Wave (mmWave) orthogonal frequency division multiplexing (OFDM) systems. By exploring the inherent sparse scattering characteristics of mmWave channels, we show that the received signals can be expressed as a low-rank third-order tensor that admits a tensor rank decomposition, also known as canonical polyadic decomposition (CPD). A structured CPD-based method is then developed to estimate the channel parameters. Our analysis reveals that the training overhead required by our prop…
We consider the problem of spatial channel covariance matrix (CCM) estimation for intelligent reflecting surface (IRS)-assisted millimeter wave (mmWave) communication systems. Spatial CCM is essential for two-timescale beamforming in IRS-assisted systems; however, estimating the spatial CCM is challenging due to the passive nature of reflecting elements and the large size of the CCM resulting from massive reflecting elements of the IRS. In this paper, we propose a CCM estimation method by exploiting the low-rankness as well as the positive semi-definite (PSD) 3-level Toeplitz structure of the …
This paper investigates two performance metrics, namely ergodic capacity and symbol error rate, of mmWave communication system assisted by a reconfigurable intelligent surface (RIS). We assume independent and identically distributed (i.i.d.) Rician fadings between user-RIS-Access Point (AP), with RIS surface consisting of passive reflecting elements. First, we derive a new unified closed-form formula for the average symbol error probability of generalised M-QAM/M-PSK signalling over this mmWave link. We then obtain new closed-form expressions for the ergodic capacity with and without channel s…
Beam alignment is required in millimeter wave communication to ensure high data rate transmission. However, with narrow beamwidth in massive MIMO, beam alignment could be computationally intensive due to the large number of beam pairs to be measured. In this paper, we propose an efficient beam alignment framework by exploiting the location information of the user equipment (UE) and potential reflecting points. The proposed scheme allows the UE and the base station to perform a coordinated beam search from a small set of beams within the error boundary of the location information, the selected …
Multiple-input multiple-output (MIMO) techniques can help in scaling the achievable air-to-ground (A2G) channel capacity while communicating with drones. However, spatial multiplexing with drones suffers from rank deficient channels due to the unobstructed line-of-sight (LoS), especially in millimeter-wave (mmWave) frequencies that use narrow beams. One possible solution is utilizing low-cost and low-complexity metamaterial-based intelligent reflecting surfaces (IRS) to enrich the multipath environment, taking into account that the drones are restricted to fly only within well-defined drone co…
Intelligent reflecting surface (IRS) technology offers more feasible propagation paths for millimeter-wave (mmWave) communication systems to overcome blockage than existing technologies. In this paper, we consider a downlink wireless system with the IRS and formulate a joint power allocation and beamforming design problem to maximize the weighted sum-rate, which is a multi-variable optimization problem. To solve the problem, we propose a novel alternating manifold optimization based beamforming algorithm. Simulation results show that our proposed optimization algorithm outperforms existing alg…
Multi-Block Attention for Efficient Channel Estimation in IRS-Assisted mmWave MIMO
School of Electrical and Computer Engineering, University of Tehran（德黑兰理工大学电子与计算机工程学院）；Department of Computer Engineering, Sharif University of Technology（谢赫·伊斯兰技术大学计算机工程系）
Intelligent reflecting surface (IRS) has emerged as a competitive solution to address blockage issues in millimeter wave (mmWave) and Terahertz (THz) communications due to its capability of reshaping wireless transmission environments. Nevertheless, obtaining the channel state information of IRS-assisted systems is quite challenging because of the passive characteristics of the IRS. In this paper, we consider the problem of beam training/alignment for IRS-assisted downlink mmWave/THz systems, where a multi-antenna base station (BS) with a hybrid structure serves a single-antenna user aided by …
5G radio at millimeter wave (mmWave) and beyond 5G concepts at 0.1-1 THz can exploit angle and delay measurements for localization, by the virtue of increased bandwidth and large antenna arrays but are limited in terms of blockage caused by obstacles. Reconfigurable intelligent surfaces (RISs) are seen as a transformative technology that can control the physical propagation environment in which they are embedded by passively reflecting EM waves in preferred directions. Whereas such RISs have been mainly intended for communication purposes, RISs can have great benefits in terms of performance, …
In this paper, we establish an integrated sensing and communication (ISAC) system based on a distributed semi-passive intelligent reflecting surface (IRS), which allows location sensing and data transmission to be carried out simultaneously, sharing the same frequency and time resources. The detailed working process of the proposed IRS-based ISAC system is designed, including the transmission protocol, location sensing and beamforming optimization. Specifically, each coherence block consists of two periods, the ISAC period with two time blocks and the pure communication (PC) period. During eac…
An intelligent reflecting surface (IRS)-assisted millimeter-wave (mmWave) massive multiple input multiple output (MIMO) system with transmit antenna selection (TAS) using orthogonal space-time block codes (OSTBC) scheme is proposed in this paper. This system combines TAS and IRS with hybrid analog-digital beamforming (HBF) for 60 GHz mmWave communications in order to exploit the benefits of TAS, OSTBC, analog beamforming (ABF), and transmit digital precoding techniques. The proposed system, however, benefits from the transmit diversity gain of OSTBC scheme as well as from the signal-to-noise r…
Capacity-Net-Based RIS Precoding Design without Channel Estimation for mmWave MIMO System
Institute of Communication Engineering (ICE), National Sun Yat-sen University (NSYSU)（通信工程研究所，国立中山大学）；Research Center for Information Technology Innovation (CITI), Academia Sinica (AS)（资讯科技创新研究中心，中华学术院）；Department of Electrical Engineering, National Ilan University (NIU)（电气工程系，国立宜兰大学）
