submitted for possible journal publication (Part of this work will be presented in the IEEE International Conference on Communications (ICC), Dublin, Ireland, 2020 Available: arXiv:1907.06002)
Intelligent reflecting surface (IRS) that enables the control of wireless propagation environment has recently emerged as a promising cost-effective technology for boosting the spectrum and energy efficiency in future wireless communication systems. Prior works on IRS are mainly based on the ideal phase shift model assuming the full signal reflection by each of the elements regardless of its phase shift, which, however, is practically difficult to realize. In contrast, we propose in this paper the practical phase shift model that captures the phase-dependent amplitude variation in the element-wise reflection coefficient. Based on the proposed model and considering an IRS-aided multiuser system with an IRS deployed to assist in the downlink communications from a multi-antenna access point (AP) to multiple single-antenna users, we formulate an optimization problem to minimize the total transmit power at the AP by jointly designing the AP transmit beamforming and the IRS reflect beamforming, subject to the users' individual signal-to-interference-plus-noise ratio (SINR) constraints. Iterative algorithms are proposed to find suboptimal solutions to this problem efficiently by utilizing the alternating optimization (AO) or penalty-based optimization technique. Moreover, we analyze the asymptotic performance loss of the IRS-aided system that employs practical phase shifters but assumes the ideal phase shift model for beamforming optimization, as the number of IRS elements goes to infinity. Simulation results unveil substantial performance gains achieved by the proposed beamforming optimization based on the practical phase shift model as compared to the conventional ideal model.
This work proposes linear time strategies to optimally configure the phase shifts for the reflective elements of an intelligent reflecting surface (IRS). Specifically, we show that the binary phase beamforming can be optimally solved in linear time to maximize the received signal-to-noise ratio (SNR). For the general K-ary phase beamforming, we develop a linear time approximation algorithm that guarantees performance within a constant fraction (1+\cos(π/K))/2 of the global optimum, e.g., it can attain over 85% of the optimal performance for the quadrature beamforming with K=4. According to the…
Intelligent reflecting surface (IRS) has become a promising technology to aid next generation wireless communication systems. In this paper, we develop an alternating beamforming technique with a novel concept of IRS element allocation for multiple-input multiple-output systems when a base station supports multiple single antenna users aided with a single IRS. Specifically, we allocate each IRS element separately to each user, thus, in the beamforming stage allowing the IRS element only consider a single user at a time. In result to this separation, the complexity is vastly decreased. The prop…
Intelligent reflecting surface (IRS) is a proposing technology in 6G to enhance the performance of wireless networks by smartly reconfiguring the propagation environment with a large number of passive reflecting elements. However, current works mainly focus on single IRS-empowered wireless networks, where the channel rank deficiency problem has emerged. In this paper, we propose a distributed IRS-empowered communication network architecture, where multiple source-destination pairs communicate through multiple distributed IRSs. We further contribute to maximize the achievable sum-rates in this …
In this paper, we study the waveform and passive beamforming design for intelligent reflecting surface (IRS)-aided wireless power transfer (WPT). Generalized multi-user and low complexity single-user algorithms are derived based on alternating optimization (AO) framework to maximize the weighted sum output DC current, subject to transmit power constraints and passive beamforming phases unit modulus constraints. The input signal waveform and IRS passive beamforming phase shifts are jointly designed as a function of users' individual frequency-selective channel state information (CSI). The energ…
Reconfigurable intelligent surface (RIS) provides a promising way to build the programmable wireless transmission environments in the future. Owing to the large number of reflecting elements used at the RIS, joint optimization for the active beamforming at the transmitter and the passive reflector at the RIS is usually complicated and time-consuming. To address this problem, this paper proposes a low-complexity joint beamforming and reflecting algorithm based on fractional programing (FP). Specifically, we first consider a RIS-aided multi-user communication system with perfect channel state in…
As communication systems that employ millimeter wave (mmWave) frequency bands must use large antenna arrays to overcome the severe propagation loss of mmWave signals, hybrid beamforming has been considered as an integral component of mmWave communications. Recently, intelligent reflecting surface (IRS) has been proposed as an innovative technology that can significantly improve the performance of mmWave communication systems through the use of low-cost passive reflecting elements. In this paper, we study IRS-aided mmWave multiple-input multiple-output (MIMO) systems with hybrid beamforming arc…
This paper investigates the achievable rate region of the multiple-input single-output (MISO) interference channel aided by intelligent reflecting surfaces (IRSs). We exploit the the additional design degree of freedom provided by the coordinated IRSs to enhance the desired signal and suppress interference so as to enlarge the achievable rate region of the interference channel. To this end, we jointly optimize the active transmit beamforming at the transmitters and passive reflective beamforming at the IRSs, subject to the constant modulus constraints of reflective beamforming vectors. To addr…
In this letter, we investigate joint application of reconfigurable intelligent surface (RIS) and vertical beamforming in cognitive radio networks (CRN). After properly modeling the network, an optimization problem is formed to jointly design the beamforming vector and tilt angle at the secondary base station (BS) as well as the phase shifts at the RIS with the objective of maximizing spectral efficiency of the secondary network. The optimization problem is non-convex; thus, we propose an efficient solution method for it. Numerical results show that adding a RIS and optimizing the radiation ori…
Intelligent reflecting surface (IRS) that enables the control of the wireless propagation environment has been looked upon as a promising technology for boosting the spectrum and energy efficiency in future wireless communication systems. Prior works on IRS are mainly based on the ideal phase shift model assuming the full signal reflection by each of the elements regardless of its phase shift, which, however, is practically difficult to realize. In contrast, we propose in this paper a practical phase shift model that captures the phase-dependent amplitude variation in the element-wise reflecti…
Intelligent reflecting surface (IRS) has emerged as a cost-effective solution to enhance wireless communication performance via passive signal reflection. Existing works on IRS have mainly focused on investigating IRS's passive beamforming/reflection design to boost the communication rate for users assuming that their channel state information (CSI) is fully or partially known. However, how to exploit IRS to improve the wireless transmission reliability without any CSI, which is typical in high-mobility/delay-sensitive communication scenarios, remains largely open. In this paper, we study a ne…
While intelligent reflecting surface (IRS) assisted wireless communication has emerged as an important research paradigm, channel state information (CSI) acquisition remains a critical challenge to design the IRS phase-shifts and yield the promised coherent beamforming gains. In this paper, we propose an IRS-assisted opportunistic beamforming (OBF) scheme under proportional fair scheduling, which does not require instantaneous CSI to design the IRS parameters. In a slow-fading environment, we show that with only random rotations at the IRS, the proposed scheme can capitalize on the multi-user …
Intelligent reflecting surface (IRS) has the potential to significantly enhance the network performance by reconfiguring the wireless propagation environments. It is however difficult to obtain the accurate downlink channel state information (CSI) for efficient beamforming design in IRS-aided wireless networks. In this article, we consider an IRS-aided downlink multiple-input single-output (MISO) network, where the base station (BS) is not required to know the underlying channel distribution. We formulate an outage probability minimization problem by jointly optimizing the beamforming vector a…
We consider in this paper a new intelligent reflecting surface (IRS)-aided LEO satellite communication system, by utilizing the controllable phase shifts of massive passive reflecting elements to achieve flexible beamforming, which copes with the time-varying channel between the high-mobility satellite (SAT) and ground node (GN) cost-effectively. In particular, we propose a new architecture for IRS-aided LEO satellite communication where IRSs are deployed at both sides of the SAT and GN, and study their cooperative passive beamforming (CPB) design over line-of-sight (LoS)-dominant single-refle…
In this paper, we consider covert beamforming design for intelligent reflecting surface (IRS) assisted Internet of Things (IoT) networks, where Alice utilizes IRS to covertly transmit a message to Bob without being recognized by Willie. We investigate the joint beamformer design of Alice and IRS to maximize the covert rate of Bob when the knowledge about Willie's channel state information (WCSI) is perfect and imperfect at Alice, respectively. For the former case, we develop a covert beamformer under the perfect covert constraint by applying semidefinite relaxation. For the later case, the opt…
This letter investigates the joint active and passive beamforming optimization for intelligent reflecting surface (IRS) aided multiuser multiple-input multiple-output systems with the objective of maximizing the weighted sum-rate. We show that this problem can be solved via a matrix weighted mean square error minimization equivalence. In particular, for the optimization of the passive IRS beamforming, we first propose an iterative algorithm with excellent performance based on the manifold optimization. By using the matrix fractional programming technique to obtain a more tractable object funct…
Large intelligent surface (LIS) has emerged as a promising new solution to improve the energy and spectrum efficiency of wireless networks. A LIS, composed of a large number of low-cost and energy-efficient reconfigurable passive reflecting elements, enhances wireless communications by reflecting impinging electro-magnetic waves. In this paper, we propose a novel passive beamforming and information transfer (PBIT) technique, in which the LIS simultaneously enhances the primary communication and sends information to the receiver. We develop a passive beamforming method to improve the average re…
Terahertz (THz) communications open a new frontier for the wireless network thanks to their dramatically wider available bandwidth compared to the current micro-wave and forthcoming millimeter-wave communications. However, due to the short length of THz waves, they also suffer from severe path attenuation and poor diffraction. To compensate the THz-induced propagation loss, this paper proposes to combine two promising techniques, viz., massive multiple input multiple output (MIMO) and intelligent reflecting surface (IRS), in THz multi-user communications, considering their significant beamform…
Intelligent reflecting surfaces (IRSs) have received much attention recently and are envisioned to promote 6G communication networks. In this paper, for wireless communications aided by IRS units, we formulate optimization problems for power control under quality of service (QoS) and max-min fair QoS under three kinds of traffic patterns from a base station (BS) to mobile users (MUs): unicast, broadcast, and multicast. The optimizations are achieved by jointly designing the transmit beamforming of the BS and the phase shift matrix of the IRS. For power control under QoS, existing IRS studies i…
Considering intelligent reflecting surface (IRS), we study a multi-cluster multiple-input-single-output (MISO) non-orthogonal multiple access (NOMA) downlink communication network. In the network, an IRS assists the communication from the base station (BS) to all users by passive beamforming. Our goal is to minimize the total transmit power by jointly optimizing the transmit beamforming vectors at the BS and the reflection coefficient vector at the IRS. Because of the restrictions on the IRS reflection amplitudes and phase shifts, the formulated quadratically constrained quadratic problem is h…
This work gives a blind beamforming strategy for intelligent reflecting surface (IRS), aiming to boost the received signal-to-noise ratio (SNR) by coordinating phase shifts across reflective elements in the absence of channel information. While the existing methods of IRS beamforming typically first estimate channels and then optimize phase shifts, we propose a conditional sample mean based statistical approach that explores the wireless environment via random sampling without performing any channel estimation. Remarkably, the new method just requires a polynomial number of random samples to y…
This paper investigates multiuser multi-input single-output downlink symbiotic radio communication systems assisted by an intelligent reflecting surface (IRS). Different from existing methods ideally assuming the secondary user (SU) can jointly decode information symbols from both the access point (AP) and the IRS via multiuser detection, we consider a more practical SU that only non-coherent detection is available. To characterize the non-coherent decoding performance, a practical upper bound of the average symbol error rate (SER) is derived. Subsequently, we jointly optimize the beamformer a…
Wireless communications via intelligent reflecting surfaces (IRSs) has received considerable attention from both academia and industry. In particular, IRSs are able to create favorable wireless propagation environments with typically low-cost passive devices. While various IRS-aided wireless communication systems have been investigated in the literature, thus far, the optimal design of such systems is not well understood. In this paper, IRS-assisted single-user multiple-input single-output (MISO) communication is investigated. To maximize the spectral efficiency, a branch-and-bound (BnB) algor…
This paper considers an active intelligent reflecting surface (IRS)-aided wireless powered communication network (WPCN), where devices first harvest energy and then transmit information to a hybrid access point (HAP). Different from the existing works on passive IRS-aided WPCNs, this is the first work that introduces the active IRS in WPCNs. To guarantee fairness, the problem is formulated as an amplifying power-limited weighted sum throughput (WST) maximization problem, which is solved by successive convex approximation technique and fractional programming alternatively. To balance the perfor…
The current literature on intelligent reflecting surface (IRS) focuses on optimizing the IRS phase shifts to yield coherent beamforming gains, under the assumption of perfect channel state information (CSI) of individual IRS-assisted links, which is highly impractical. This work, instead, considers the random rotations scheme at the IRS in which the reflecting elements only employ random phase rotations without requiring any CSI. The only CSI then needed is at the base station (BS) of the overall channel to implement the beamforming transmission scheme. Under this framework, we derive the sum-…
This paper investigates a multiuser downlink communication system with coexisting intelligent reflecting surface (IRS) and classical half-duplex decode-and-forward (DF) relay. In this system, the IRS and the DF relay interact with each other and assist transmission simultaneously. In particular, active beamforming at the base station (BS) and at the DF relay, and passive beamforming at the IRS, are jointly designed to maximize the sum-rate of all users. The sum-rate maximization problem is nonconvex due to the coupled beamforming vectors. We propose an alternating optimization (AO) based algor…
In this letter, we investigate the robust and secure beamforming (RSBF) in an intelligent reflecting surface (IRS) aided millimeter wave (mmWave) multiple input single output (MISO) system, where multiple single antenna eavesdroppers (Eves) are arbitrarily distributed nearby the legitimate receiver. Considering the channel state information (CSI) of Eves' channels is imperfectly known at the legitimate transmitter, the RSBF design problems to maximize the worst case of achievable secrecy rate (ASR) are formulated under the total transmission power and unit-modulus constraints. Since the proble…
Reconfigurable intelligent surface has recently emerged as a promising technology for shaping the wireless environment by leveraging massive low-cost reconfigurable elements. Prior works mainly focus on a single-layer metasurface that lacks the capability of suppressing multiuser interference. By contrast, we propose a stacked intelligent metasurface (SIM)-enabled transceiver design for multiuser multiple-input single-output downlink communications. Specifically, the SIM is endowed with a multilayer structure and is deployed at the base station to perform transmit beamforming directly in the e…
Bistatic backscatter communication (BackCom) allows passive tags to transmit over extended ranges, but at the cost of having carrier emitters either transmitting at high powers or being deployed very close to tags. In this paper, we examine how the presence of an intelligent reflecting surface (IRS) could benefit the bistatic BackCom system. We study the transmit power minimization problem at the carrier emitter, where its transmit beamforming vector is jointly optimized with the IRS phase shifts, whilst guaranteeing a required BackCom performance. A unique feature in this system setup is the …
We consider reconfigurable intelligent surface (RIS) aided sixth-generation (6G) terahertz (THz) communications for indoor environment in which a base station (BS) wishes to send independent messages to its serving users with the help of multiple RISs. For indoor environment, various obstacles such as pillars, walls, and other objects can result in no line-of-sight signal path between the BS and a user, which can significantly degrade performance. To overcome such limitation of indoor THz communication, we firstly optimize the placement of RISs to maximize the coverage area. Under the optimize…
In this paper, we study the problem of joint active and passive beamforming for intelligent reflecting surface (IRS)-assisted massive MIMO systems, where multiple IRSs equipped with a large number of passive elements are deployed to assist a base station (BS) to simultaneously serve a small number of single-antenna users in the same time-frequency resource. Our objective is to maximize the minimum signal to interference plus noise (SINR) at users by jointly optimizing the transmit precoding vector at the BS and phase shift parameters at IRSs. We show that an interesting automatic interference …
This paper considers an intelligent reflecting surface (IRS) aided multiple-input single-output communication system, where statistical channel state information (CSI) is exploited for transmit beamforming and IRS beamforming. A tight upper bound is derived for the ergodic capacity of the system. Based on which, the joint optimization of transmit beam and IRS beam are studied. Depending on whether a line-of-sight path exists between the access point and user, two different cases, namely, Rician fading and Rayleigh fading, are separately treated. Specifically, for the Rician fading case, an ite…
Intelligent reflecting surface (IRS) is a cost-efficient technique to improve power efficiency and spectral efficiency. However, IRS-aided multi-antenna transmission needs to jointly optimize the passive and active beamforming, imposing a high computational burden and high latency due to its iterative optimization process. Making use of hybrid analog-digital beamforming in high-frequency transmission systems, a novel technique, coined dual-beam IRS, is proposed in this paper. The key idea is to form a pair of beams towards the IRS and user, respectively. Then, the optimization of passive and a…
This letter aims to clarify the impact of channel aging and phase noise on the performance of intelligent reflecting surface-aided wireless systems. We first model mathematically the outdated channel state information (CSI) due to Doppler shifts and phase noise stemming from hardware impairment. Then, a closed-form expression of achievable spectral efficiency under noisy and aged CSI is theoretically derived. Some typical simulation results to numerically demonstrate the performance impact are illustrated.
This letter focuses on the secure transmission for an intelligent reflecting surface (IRS)-assisted millimeter-wave (mmWave) and terahertz (THz) systems, in which a base station (BS) communicates with its destination via an IRS, in the presence of a passive eavesdropper. To maximize the system secrecy rate, the transmit beamforming at the BS and the reflecting matrix at the IRS are jointly optimized with transmit power and discrete phase-shift constraints. It is first proved that the beamforming design is independent of the phase shift design under the rank-one channel assumption. The formulat…
Different from traditional reflection-only reconfigurable intelligent surfaces (RISs), simultaneously transmitting and reflecting RISs (STAR-RISs) represent a novel technology, which extends the half-space coverage to full-space coverage by simultaneously transmitting and reflecting incident signals. STAR-RISs provide new degrees-of-freedom (DoF) for manipulating signal propagation. Motivated by the above, a novel STAR-RIS assisted non-orthogonal multiple access (NOMA) (STAR-RIS-NOMA) system is proposed in this paper. Our objective is to maximize the achievable sum rate by jointly optimizing t…
Reconfigurable Intelligent Surfaces (RIS) or Intelligent Reflecting Surfaces (IRS) are metasurfaces that can be deployed in various places in wireless environments to make these environments controllable and reconfigurable. In this paper, we investigate the problem of using 3D beamforming in RIS-empowered wireless networks and propose a new scheme that provides more degrees of freedom in designing and deploying the RIS-based networks. In the proposed scheme, a base station (BS) equipped with a full dimensional array of antennas optimizes its radiation pattern in the three-dimensional space to …
Reconfigurable intelligent surface (RIS)-empowered communication is a revolutionary technology that enables to manipulate wireless propagation environment via smartly controllable low-cost reflecting surfaces. However, in order to outperform conventional communication systems, an RIS-aided system with solely passive reflection requires an extremely large surface. To meet this challenge, the concept of active RIS, which performs simultaneous amplification and reflection on the incident signal at the expense of additional power consumption, has been recently introduced. In this paper, deploying …
In this paper, a downlink intelligent reflecting surface (IRS) enhanced millimeter-wave (mmWave) non-orthogonal multiple access (NOMA) system is considered. A joint optimization problem over active beamforming, passive beamforming and power allocation is formulated. Due to the highly coupled variables, the formulated optimization problem is non-convex. To solve this problem, an alternative optimization and successive convex approximation based iterative algorithm is proposed. Numerical results illustrate that: 1) the proposed scheme offers significant sum-rate gains, which confirms the effecti…
This paper investigates intelligent reflecting surface (IRS) enabled non-line-of-sight (NLoS) wireless sensing, in which an IRS is deployed to assist an access point (AP) to sense a target in its NLoS region. It is assumed that the AP is equipped with multiple antennas and the IRS is equipped with a uniform linear array. The AP aims to estimate the target's direction-of-arrival (DoA) with respect to the IRS, based on the echo signals from the AP-IRS-target-IRS-AP link. Under this setup, we jointly design the transmit beamforming at the AP and the reflective beamforming at the IRS to minimize t…
In this paper, we introduce a variant of reconfigurable intelligent surfaces (RISs) called omni-digital-RISs (DRISs), which allow multiple physical processes, with application to optical wireless communications systems. The proposed omni-DRIS contains both reflectors and refractive elements, as well as elements that perform both simultaneously. We describe and explain the concept of omni-DRIS, suggest and analyze an omni-DRIS coding structure, discuss metamaterials to be used, and provide a design example. Furthermore, we demonstrate that the achievable rate of an omni-DRIS system depends on t…
This paper investigates the passive beamforming and deployment design for an intelligent reflecting surface (IRS) aided full-duplex (FD) wireless system, where an FD access point (AP) communicates with an uplink (UL) user and a downlink (DL) user simultaneously over the same time-frequency dimension with the help of IRS. Under this setup, we consider three deployment cases: 1) two distributed IRSs placed near the UL user and DL user, respectively; 2) one centralized IRS placed near the DL user; 3) one centralized IRS placed near the UL user. In each case, we aim to minimize the weighted sum tr…
In this work, we propose a new single-RF MIMO architecture which enjoys high scalability and energy-efficiency. The transmitter in this proposal consists of a single RF illuminator radiating towards a reflecting surface. Each element on the reflecting surface re-transmits its received signal after applying a phase-shift, such that a desired beamforming pattern is obtained. For this architecture, the problem of beamforming is interpreted as linear regression and a solution is derived via the method of least-squares. Using this formulation, a fast iterative algorithm for tuning of the reflecting…
This letter investigates secure transmission in an intelligent reflecting surface (IRS) assisted non-orthogonal multiple access (NOMA) network. Consider a practical eavesdropping scenario with imperfect channel state information of the eavesdropper, we propose a robust beamforming scheme using artificial noise to guarantee secure NOMA transmission with the IRS. A joint transmit beamforming and IRS phase shift optimization problem is formulated to minimize the transmit power. Since the problem is non-convex and challenging to resolve, we develop an effective alternative optimization (AO) algori…
Intelligent Reflecting Surface (IRS) has been a promising solution to enhance wireless networks both spectral-efficiently and energy-efficiently. This paper considers an IRS-assisted the Internet of Things network for massive connectivity. We aim to solve the IRS-related activity detection and channel estimation problem which has not been studied before. In this paper, we formulate the IRS-related activity detection and channel estimation problem as sparse matrix factorization, matrix completion and Multiple Measurement Vector problem and, we propose a three-stage framework based on the approx…
Intelligent reflecting surface (IRS) has emerged as a key enabling technology to realize smart and reconfigurable radio environment for wireless communications, by digitally controlling the signal reflection via a large number of passive reflecting elements in real-time. Different from conventional wireless communication techniques that only adapt to but have no or limited control over dynamic wireless channels, IRS provides a new and cost-effective means to combat the wireless channel impairments in a proactive manner. However, despite its great potential, IRS faces new and unique challenges …
With the advancement of sensing technologies over the years, it has become critical to ensure the seamless connectivity of the Internet of Things (IoT) gadgets. With the advancement of communication technology, cellular networks are increasingly being utilized to link IoT systems. An IRS is a rectangular metasurface made up of a vast number of reflecting components that has recently gained research attention due to its ability to significantly improve the energy and spectral efficiencies of communication networks by modifying wireless transmission environments.
In reconfigurable intelligent surfaces (RISs) aided communications, the existing passive beamforming (PB) design involves polynomial complexity in the number of reflecting elements, and thus is difficult to implement due to a massive number of reflecting elements. To overcome this difficulty, we propose a reflection-angle-based cascaded channel model by adopting the generalized Snell's law, in which the dimension of the variable space involved in optimization is significantly reduced, resulting in a simplified hierarchical passive beamforming (HPB) design. We develop an efficient two-stage HPB…
Reducing computational complexity is crucial in optimizing the phase shifts of Intelligent Reflecting Surface (IRS) systems since IRS-assisted communication systems are generally deployed with a large number of reflecting elements (REs). This letter proposes a low-complexity algorithm, designated as Dimension-wise Sinusoidal Maximization (DSM), to obtain the optimal IRS phase shifts that maximize the sum capacity of a MIMO network. The algorithm exploits the fact that the objective function for the optimization problem is sinusoidal w.r.t. the phase shift of each RE. The numerical results show…
This paper investigates the passive beamforming and information transfer (PBIT) technique for the multiuser multiple-input multiple-output (MIMO) systems with the aid of a reconfigurable intelligent surface (RIS), where the RIS enhances the primary communication via passive beamforming and at the same time delivers additional information by the spatial modulation (which adjusts the on-off states of the reflecting elements). For the passive beamforming design, we propose to maximize the sum channel capacity of the RIS-aided multiuser MIMO channel and formulate the problem as a two-step stochast…
Most prior works on intelligent reflecting surface (IRS) merely consider point-to-point communications, including a single user, for ease of analysis. Nevertheless, a practical wireless system needs to accommodate multiple users simultaneously. Due to the lack of frequency-selective reflection, namely the set of phase shifts cannot be different across frequency subchannels, the integration of IRS imposes a fundamental challenge to frequency-multiplexing approaches such as frequency-division multiple access (FDMA) and the widely adopted technique called orthogonal FDMA (OFDMA). It motivates us …
In this paper, we study the performance of wideband terahertz (THz) communications assisted by an intelligent reflecting surface (IRS). Specifically, we first introduce a generalized channel model that is suitable for electrically large THz IRSs operating in the near-field. Unlike prior works, our channel model takes into account the spherical wavefront of the emitted electromagnetic waves and the spatial-wideband effect. We next show that conventional frequency-flat beamfocusing significantly reduces the power gain due to beam squint, and hence is highly suboptimal. More importantly, we analy…
This paper considers an intelligent reflecting sur-face (IRS)-aided simultaneous wireless information and power transfer (SWIPT) network, where multiple users decode data and harvest energy from the transmitted signal of a transmit-ter. The proposed design framework exploits the cost-effective IRS to establish favorable communication environment to improve the fair energy efficient. In particular, we study the max-min energy efficiency (EE) of the system by jointly designing the transmit information and energy beamforming at the base station (BS), phase shifts at the IRS, as well as the power …
