The emerging quantum technological applications call for fast and accurate initialization of the corresponding devices to low-entropy quantum states. To this end, we theoretically study a recently demonstrated quantum-circuit refrigerator in the case of non-linear quantum electric circuits such as superconducting qubits. The maximum refrigeration rate of transmon and flux qubits is observed to be roughly an order of magnitude higher than that of usual linear resonators, increasing flexibility in the design. We find that for typical experimental parameters, the refrigerator is suitable for resetting different qubit types to fidelities above 99.99% in a few or a few tens of nanoseconds depending on the scenario. Thus the refrigerator appears to be a promising tool for quantum technology and for detailed studies of open quantum systems.
An implementation of a small quantum absorption refrigerator in a circuit QED architecture is proposed. The setup consists of three harmonic oscillators coupled to a Josephson unction. The refrigerator is autonomous in the sense that it does not require any external control for cooling, but only thermal contact between the oscillators and heat baths at different temperatures. In addition, the setup features a built-in switch, which allows the cooling to be turned on and off. If timing control is available, this enables the possibility for coherence-enhanced cooling. Finally, we show that signi…
Quantum technology promises revolutionizing applications in information processing, communications, sensing, and modelling. However, efficient on-demand cooling of the functional quantum degrees of freedom remains a major challenge in many solid-state implementations, such as superconducting circuits. Here, we demonstrate direct cooling of a superconducting resonator mode using voltage-controllable quantum tunneling of electrons in a nanoscale refrigerator. This result is revealed by a decreased electron temperature at a resonator-coupled probe resistor, even when the electrons in the refriger…
Superconducting circuits present a promising platform with which to realize a quantum refrigerator. Motivated by this, we fabricate and perform spectroscopy of a gated Cooper-pair box, capacitively coupled to two superconducting coplanar waveguide resonators with different frequencies. We experimentally demonstrate the strong coupling of a charge qubit to two superconducting resonators, with the ability to perform voltage driving of the qubit at GHz frequencies. We go on to discuss how the measured device could be modified to operate as a cyclic quantum refrigerator by terminating the resonato…
Absorption refrigerators are autonomous thermal machines that harness the spontaneous flow of heat from a hot bath into the environment in order to perform cooling. Here we discuss quantum realizations of absorption refrigerators in two different settings: namely, cavity and circuit quantum electrodynamics. We first provide a unified description of these machines in terms of the concept of virtual temperature. Next, we describe the two different physical setups in detail and compare their properties and performance. We conclude with an outlook on future work and open questions in this field of…
We investigate a mesoscopic refrigerator based on chiral quantum Hall edge channels. We discuss a three-terminal cooling device in which charge transport occurs between a pair of voltage-biased terminals only. The third terminal, which is to be cooled, is set as a voltage probe with vanishing particle flux. This largely prevents the generation of direct Joule heating which ensures a high coefficient of performance. Cooling operation is based on energy-dependent quantum transmissions. The latter are implemented with the aid of two tunable scattering resonances (quantum dots). To find the optima…
We build on the study of single-photon heat conduction in electronic circuits taking into account the back-action of the superconductor--insulator--normal-metal thermometers. In addition, we show that placing capacitors, resistors, and superconducting quantum interference devices (SQUIDs) into a microwave cavity can severely distort the spatial current profile which, in general, should be accounted for in circuit design. The introduction of SQUIDs also allows for in situ tuning of the photonic power transfer which could be utilized in experiments on superconducting quantum bits.
We propose a method for fast, deterministic resonator reset based on tunable dissipative modes. The dissipator is based on a Josephson junction with relatively low quality factor. When the dissipator is tuned into resonance with a high quality microwave resonator, resonator photons are absorbed by the dissipator at a rate orders of magnitude faster than the resonator relaxation rate. We determine the optimal parameters for realization of the tunable dissipator, and examine application of the dissipator to removing spurious photon population in the qubit readout resonator in circuit quantum ele…
Electrically controllable quantum coherence in quantum dot clusters and arrays based on graphene stripes with zigzag atomic edges (ZZ-stripes) is studied using the Dirac equation and S-matrix technique. We find that respective multiqubit circuits promise stable operation up to room temperatures when the coherence time is prolonged up by a few orders of magnitude through the intrinsic spectral narrowing owing to electron transport between at bands in adjacent sections. Respectively, the coupling of qubits to a noisy environment is diminished, while the inelastic electron-phonon scattering is su…
We report on a planar microwave resonator providing arbitrarily polarized oscillating magnetic fields that enable selective excitation of the electronic spins of nitrogen-vacancy (NV) centers in diamond. The polarization plane is parallel to the surface of diamond, which makes the resonator fully compatible with (111)-oriented diamond. The field distribution is spatially uniform in a circular area with a diameter of 4 mm, and a near-perfect circular polarization is achieved. We also demonstrate that the original resonance frequency of 2.8 GHz can be varied in the range of 2-3.2 GHz by introduc…
We have designed, fabricated and measured high-Q $λ/2$ coplanar waveguide microwave resonators whose resonance frequency is made tunable with magnetic field by inserting a DC-SQUID array (including 1 or 7 SQUIDs) inside. Their tunability range is 30% of the zero field frequency. Their quality factor reaches up to 3$\times10^4$. We present a model based on thermal fluctuations that accounts for the dependance of the quality factor with magnetic field.
A robust cryogenic infrastructure in form of a wired, thermally optimized dilution refrigerator is essential for present and future solid-state based quantum processors. Here, we engineer an extensible cryogenic setup, which minimizes passive and active heat loads, while guaranteeing rapid qubit control and readout. We review design criteria for qubit drive lines, flux lines, and output lines used in typical experiments with superconducting circuits and describe each type of line in detail. The passive heat load of stainless steel and NbTi coaxial cables and the active load due to signal dissi…
We describe a method to tune, in-situ, between transverse and longitudinal light-matter coupling in a hybrid circuit-QED device composed of an electron spin degree of freedom coupled to a microwave transmission line cavity. Our approach relies on periodic modulation of the coupling itself, such that in a certain frame the interaction is both amplified and either transverse, or, by modulating at two frequencies, longitudinal. The former realizes an effective simulation of certain aspects of the ultra-strong coupling regime, while the latter allows one to implement a longitudinal readout scheme …
We propose a tunable on-chip micromaser using a superconducting quantum circuit (SQC). By taking advantage of externally controllable state transitions, a state population inversion can be achieved and preserved for the two working levels of the SQC and, when needed, the SQC can generate a single photon. We can regularly repeat these processes in each cycle when the previously generated photon in the cavity is decaying, so that a periodic sequence of single photons can be produced persistently. This provides a controllable way for implementing a persistent single-photon source on a microelectr…
We propose to implement tunable interaction of superconducting flux qubits with cavity-assisted interaction and strong driving. The qubits have a three-level Lambda configuration, and the decay of the excited state will be greatly suppressed due to the effective large detuning. The implemented interaction is insensitive to the cavity field state and can be controlled by modulating the phase difference of the driving fields of the qubits. In particular, our scheme is based on the typical circuit QED setup and thus will provide a simple method towards the tunable interaction of superconducting q…
Circuit quantum electrodynamics, where photons are coherently coupled to artificial atoms built with superconducting circuits, has enabled the investigation and control of macroscopic quantum-mechanical phenomena in superconductors. Recently, hybrid circuits incorporating semiconducting nanowires and other electrostatically-gateable elements have provided new insights into mesoscopic superconductivity. Extending the capabilities of hybrid flux-based circuits to work in magnetic fields would be especially useful both as a probe of spin-polarized Andreev bound states and as a possible platform f…
We focus on a recently experimentally realized scenario of normal-metal-insulator-superconductor tunnel junctions coupled to a superconducting resonator. We develop a first-principles theory to describe the effect of photon-assisted electron tunneling on the quantum state of the resonator. Our results are in very good quantitative agreement with the previous experiments on refrigeration and heating of the resonator using the photon-assisted tunneling, thus providing a stringent verification of the developed theory. Importantly, our results provide simple analytical estimates of the voltage-tun…
Microwave experiments in dilution refrigerators are a central tool in the field of superconducting quantum circuits and other research areas. This type of experiments relied so far on attaching a device to the mixing chamber of a dilution refrigerator. The minimum turnaround time in this case is a few days as required by cooling down and warming up the entire refrigerator. We developed a new approach, in which a suitable sample holder is attached to a cold-insertable probe and brought in contact with transmission lines permanently mounted inside the cryostat. The total turnaround time is 8 hou…
Quantum phase transitions are ubiquitous in many exotic behaviors of strongly-correlated materials. However the microscopic complexity impedes their quantitative understanding. Here, we observe thoroughly and comprehend the rich strongly-correlated physics in two profoundly dissimilar regimes of quantum criticality. With a circuit implementing a quantum simulator for the three-channel Kondo model, we reveal the universal scalings toward different low-temperature fixed points and along the multiple crossovers from quantum criticality. Notably, an unanticipated violation of the maximum conductan…
A detailed analysis of the tunability of a radio-frequency quantum point contact setup using a C-LCR circuit is presented. We calculate how the series capacitance influences resonance frequency and charge-detector resistance for which matching is achieved as well as the voltage and power delivered to the load. Furthermore, we compute the noise contributions in the system and compare our findings with measurements taken with an etched quantum point contact. While our considerations mostly focus on our specific choice of matching circuit, the discussion of the influence of source-to-load power t…
The harmonic oscillator is one of the most widely used model systems in physics: an indispensable theoretical tool in a variety of fields. It is well known that otherwise linear oscillators can attain novel and nonlinear features through interaction with another dynamical system. We investigate such an interacting system: a superconducting LC-circuit dispersively coupled to a superconducting quantum interference device (SQUID). We find that the SQUID phase behaves as a classical two-level system, whose two states correspond to one linear and one nonlinear regime for the LC-resonator. As a resu…
Superconducting microwave circuits show great potential for practical quantum technological applications such as quantum information processing. However, fast and on-demand initialization of the quantum degrees of freedom in these devices remains a challenge. Here, we experimentally implement a tunable heat sink that is potentially suitable for the initialization of superconducting qubits. Our device consists of two coupled resonators. The first resonator has a high quality factor and a fixed frequency whereas the second resonator is designed to have a low quality factor and a tunable resonanc…
Observation of coherent flux-charge interaction in a gate-tunable fluxonium
University of Colorado Boulder（科罗拉多大学博尔德分校）；Université de Sherbrooke（舍布鲁克大学）；Niels Bohr Institute, University of Copenhagen（哥本哈根大学尼尔斯·玻尔研究所）；Technical University of Munich（慕尼黑工业大学）；Bayerische Akademie der Wissenschaften（巴伐利亚科学院）
Engineered quantum systems allow us to observe phenomena that are not easily accessible naturally. The LEGO-like nature of superconducting circuits makes them particularly suited for building and coupling artificial atoms. Here, we introduce an artificial molecule, composed of two strongly coupled fluxonium atoms, which possesses a tunable magnetic moment. Using an applied external flux, one can tune the molecule between two regimes: one in which the ground-excited state manifold has a magnetic dipole moment and one in which the ground-excited state manifold has only a magnetic quadrupole mome…
Incorporating a variable capacitance diode into a radio-frequency matching circuit allows us to in-situ tune the resonance frequency of an RF quantum point contact, increasing the versatility of the latter as a fast charge sensor of a proximal quantum circuit. The performance of this method is compared in detail to conventional low-frequency charge detection. The approach is also applicable to other RF-detection schemes, such as RF-SET circuits.
We report on fast tunability of an electromagnetic environment coupled to a superconducting coplanar waveguide resonator. Namely, we utilize a recently-developed quantum-circuit refrigerator (QCR) to experimentally demonstrate a dynamic tunability in the total damping rate of the resonator up to almost two orders of magnitude. Based on the theory it corresponds to a change in the internal damping rate by nearly four orders of magnitude. The control of the QCR is fully electrical, with the shortest implemented operation times in the range of 10 ns. This experiment constitutes a fast active rese…
We report on experiments with superconducting metamaterials containing Josephson junctions. In these structures, split-ring resonators used in conventional metamaterials are replaced by superconducting loops that are interrupted by Josephson junctions, so called rf-SQUIDs. Like the split-ring resonators, these elements can be seen as LC-resonators that couple to the magnetic field. The advantage of superconducting thin-film metamaterials is that, due to the tunable intrinsic inductance of the Josephson junction, the resonance frequency of the rf-SQUID can be changed by applying an external dc …
Quantum physics emerge and develop as temperature is reduced. Although mesoscopic electrical circuits constitute an outstanding platform to explore quantum behavior, the challenge in cooling the electrons impedes their potential. The strong coupling of such micrometer-scale devices with the measurement lines, combined with the weak coupling to the substrate, makes them extremely difficult to thermalize below 10 mK and imposes in-situ thermometers. Here we demonstrate electronic quantum transport at 6 mK in micrometer-scale mesoscopic circuits. The thermometry methods are established by the com…
Nanostructures defined in high-mobility two-dimensional electron systems offer a unique way of controlling the microscopic details of the investigated device. Quantum point contacts play a key role in these investigations, since they are not only a research topic themselves, but turn out to serve as convenient and powerful detectors for their electrostatic environment. We investigate how the sensitivity of charge detectors can be further improved by reducing screening, increasing the capacitive coupling between charge and detector and by tuning the quantum point contacts' confinement potential…
With a large portfolio of elemental quantum components, superconducting quantum circuits have contributed to dramatic advances in microwave quantum optics. Of these elements, quantum-limited parametric amplifiers have proven to be essential for low noise readout of quantum systems whose energy range is intrinsically low (tens of $μ$eV ). They are also used to generate non classical states of light that can be a resource for quantum enhanced detection. Superconducting parametric amplifiers, like quantum bits, typically utilize a Josephson junction as a source of magnetically tunable and dissipa…
Superconducting quantum circuits are potential candidates to realize a large-scale quantum computer. The envisioned large density of integrated components, however, requires a proper thermal management and control of dissipation. To this end, it is advantageous to utilize tunable dissipation channels and to exploit the optimized heat flow at exceptional points (EPs). Here, we experimentally realize an EP in a superconducting microwave circuit consisting of two resonators. The EP is a singularity point of the Hamiltonian, and corresponds to the most efficient heat transfer between the resonator…
We experimentally study a circuit quantum acoustodynamics system, which consists of a superconducting artificial atom, coupled to both a two-dimensional surface acoustic wave resonator and a one-dimensional microwave transmission line. The strong coupling between the artificial atom and the acoustic wave resonator is confirmed by the observation of the vacuum Rabi splitting at the base temperature of dilution refrigerator. We show that the propagation of microwave photons in the microwave transmission line can be controlled by a few phonons in the acoustic wave resonator. Furthermore, we demon…
Curved spaces play a fundamental role in many areas of modern physics, from cosmological length scales to subatomic structures related to quantum information and quantum gravity. In tabletop experiments, negatively curved spaces can be simulated with hyperbolic lattices. Here we introduce and experimentally realize hyperbolic matter as a paradigm for topological states through topolectrical circuit networks relying on a complex-phase circuit element. The experiment is based on hyperbolic band theory that we confirm here in an unprecedented numerical survey of finite hyperbolic lattices. We imp…
Quantum thermodynamics is emerging both as a topic of fundamental research and as means to understand and potentially improve the performance of quantum devices. A prominent platform for achieving the necessary manipulation of quantum states is superconducting circuit quantum electrodynamics (QED). In this platform, thermalization of a quantum system can be achieved by interfacing the circuit QED subsystem with a thermal reservoir of appropriate Hilbert dimensionality. Here we study heat transport through an assembly consisting of a superconducting qubit capacitively coupled between two nomina…
Flexible microelectronics has shown tremendous promise in a broad spectrum of applications, especially those that cannot be addressed by conventional microelectronics in rigid materials and constructions1-3. These unconventional yet important applications range from flexible consumer electronics to conformal sensor arrays and biomedical devices. A recent successful paradigm shift in implementing flexible electronics is to physically transfer and bond highly integrated devices made in high-quality, crystalline semiconductor materials on to plastic materials4-8. Here we demonstrate a flexible fo…
We have studied microwave response of a high-mobility two-dimensional electron system (2DES) contacted by two side electrodes. Using kinetic inductance of the 2DES and inter-electrode capacitance, we have constructed a subwavelength 2D plasmonic resonator. We have shown that the resonant frequency of this circuit can be controlled by 2D electron density, external magnetic field, or size of the electrodes. This opens up possibilities for using arrays of plasmonic circuits as tunable components in different frequency ranges.
Compared to traditional pn-junction photovoltaics, hot carrier solar cells offer potentially higher efficiency by extracting work from the kinetic energy of photogenerated "hot carriers" before they cool to the lattice temperature. Hot carrier solar cells have been demonstrated in high-bandgap ferroelectric insulators and GaAs/AlGaAs heterostructures, but so far not in low-bandgap materials, where the potential efficiency gain is highest. Recently, a high open-circuit voltage was demonstrated in an illuminated wurtzite InAs nanowire with a low bandgap of 0.39 eV, and was interpreted in terms o…
Josephson junctions (JJ) are a fundamental component of microwave quantum circuits, such as tunable cavities, qubits and parametric amplifiers. Recently developed encapsulated graphene JJs, with supercurrents extending over micron distance scales, have exciting potential applications as a new building block for quantum circuits. Despite this, the microwave performance of this technology has not been explored. Here, we demonstrate a microwave circuit based on a ballistic graphene JJ embedded in a superconducting cavity. We directly observe a gate-tunable Josephson inductance through the resonan…
We study an LC-circuit implemented using a current-biased Josephson junction (CBJJ) as a tunable coupler for superconducting qubits. By modulating the bias current, the junction can be tuned in and out of resonance and entangled with the qubits coupled to it. One can thus implement two-qubit operations by mediating entanglement. We consider the examples of CBJJ and charge--phase qubits. A simple recoupling scheme leads to a generalization to arbitrary qubit designs.
The efficient implementation of many-body interactions in superconducting circuits allows for the realization of multipartite entanglement and topological codes, as well as the efficient simulation of highly correlated fermionic systems. We propose the engineering of fast multiqubit interactions with tunable transmon-resonator couplings. This dynamics is obtained by the modulation of magnetic fluxes threading superconducting quantum interference device loops embedded in the transmon devices. We consider the feasibility of the proposed implementation in a realistic scenario and discuss potentia…
Voltage-tunable Josephson Junctions on Germanium Quantum Wells with in-situ Aluminum Contacts
Laboratory for Physical Sciences（物理科学实验室）；University of Maryland, College Park（马里兰大学帕克分校）；Department of Materials Science & Engineering, University of Maryland, College Park（马里兰大学帕克分校材料科学与工程系）；University of Arkansas（阿肯色大学）；Pacific Northwest National Laboratory（太平洋西北国家实验室）
We describe a lattice of asymmetrical qubit pairs in one or two dimensions, with couplings arranged so that the motion of single-qubit excited states mimics the behavior of charged lattice bosons hopping in a magnetic field. We show in particular that one can choose the parameters of the many-body circuit to reach a regime where the complex hopping phase between any two elements can be tuned to any value by simply adjusting the relative phases of two applied oscillating voltage signals. We also propose a specific realization of our model using coupled three junction flux qubits, in which one c…
Metamaterials made of periodic arrangements of electric permittivity and magnetic permeability and arrays of resonators can provide optic properties unexperienced in conventional materials, such as negative refractive index which can be used to achieve superlensing and cloaking. Developing new simpler structures with richer electromagnetic (EM) properties and wider working frequency bands is highly demanded for fast light-based information transfer and information processing. In the present work, we propose theoretically that a honeycomb-structured LC circuit with short-range textures in induc…
We propose a scheme to realize various non-Hermitian topological phases in a topolectrical (TE) circuit network consisting of resistors, inductors, and capacitors. These phases are characterized by topologically protected exceptional points and lines. The positive and negative resistive couplings Rg in the circuit provide loss and gain factors which break the Hermiticity of the circuit Laplacian. By controlling Rg, the exceptional lines of the circuit can be modulated, e.g., from open curves to closed ellipses in the Brillouin zone. In practice, the topology of the exceptional lines can be det…
The semiconducting p-n junction is a simple device structure with great relevance for electronic and optoelectronic applications. The successful integration of low-dimensional materials in electronic circuits has opened the way forward for producing gate-tunable p-n junctions. In that context, here we present an organic (Cu-phthalocyanine)-2D layered material (MoS2) hybrid p-n junction with both gate-tunable diode characteristics and photovoltaic effect. Our proof-of-principle devices show multifunctional properties with diode rectifying factors of up to 10^4, while under light exposure they e…
