In this paper, we consider the transmit and receive antenna array gain of massive MIMO systems. In particular, we look at their dependence on the number of antennas in the array, and the antenna spacing for uniform linear and uniform circular arrays. It is known that the transmit array gain saturates at a certain antenna spacing, but the receive array gain had not been considered. With our physically consistent analysis based on the Multiport Communication Theory, we show that the receive array gain does not saturate, but that there is a peak at a certain antenna spacing when there is no decoupling network at the receiver. As implementing a decoupling network for massive MIMO would be almost impossible, this is a reasonable assumption. Furthermore, we analyze how the array gain changes depending on the antenna spacing and the size of the antenna array and derive design recommendations.
In this paper, we consider the design of a multiple-input multiple-output (MIMO) transmitter which simultaneously functions as a MIMO radar and a base station for downlink multiuser communications. In addition to a power constraint, we require the covariance of the transmit waveform be equal to a given optimal covariance for MIMO radar, to guarantee the radar performance. With this constraint, we formulate and solve the signal-to-interference-plus-noise ratio (SINR) balancing problem for multiuser transmit beamforming via convex optimization. Considering that the interference cannot be complet…
The use of multiple antennas in a transmit and receive antenna array for MIMO wireless communication allows the spatial degrees of freedom in rich scattering environments to be exploited. However, for line-of-sight (LOS) MIMO channels with uniform linear arrays (ULAs) at the transmitter and receiver, the antenna separations at the transmit and receive array need to be optimized to maximize the spatial degrees of freedom and the channel capacity. In this paper, we first revisit the derivation of the optimum antenna separation at the transmit and receive ULAs in a LOS MIMO system, and provide th…
We investigate asymptotic capacity limits of the Gaussian MIMO broadcast channel (BC) with spatially correlated fading to understand when and how much transmit correlation helps the capacity. By imposing a structure on channel covariances (equivalently, transmit correlations at the transmitter side) of users, also referred to as \emph{transmit correlation diversity}, the impact of transmit correlation on the power gain of MIMO BCs is characterized in several regimes of system parameters, with a particular interest in the large-scale array (or massive MIMO) regime. Taking the cost for downlink …
We propose a novel scheme for downlink multiuser multiple-input multiple-output (MIMO) systems, called dual-layered transmit-receive generalized spatial modulation (DL-TR-GSM). The proposed scheme is based on the concept of dual-layered transmission (DLT) which uses two receive antenna power levels instead of receive antenna activation/inactivation to transmit data in the receive spatial domain. Hence, in order to minimize the bit error rate (BER) for DL-TR-GSM, the optimal ratio between the two power levels is determined. To further characterize DL-TR-GSM, we fully derive the computational co…
The problem of finding the optimal number of data streams to transmit in a multi-user MIMO scenario, where both the transmitters and receivers are equipped with multiple antennas is considered. Without channel state information at any transmitter, with a zero-forcing receiver each user is shown to transmit a single data stream to maximize its own outage capacity in the presence of sufficient number of users. Transmitting a single data stream is also shown to be optimal in terms of maximizing the sum of the outage capacities in the presence of sufficient number of users.
This paper investigates the performance of a massive multiple-input multiple-output (MIMO) system that uses a large transmit antenna array with antenna elements spaced densely. Under the assumption of idealized uniform linear antenna arrays without mutual coupling, precoded quadrature phase-shift keying (QPSK) transmission is proved to achieve the channel capacity of the massive MIMO system when the transmit antenna separation tends to zero. This asymptotic optimality is analogous to that of QPSK faster-than-Nyquist signaling.
Multiple-input multiple-output (MIMO) or multi-antenna communication is a key technique to achieve high spectral efficiency in wireless systems. For the point-to-point MIMO channel, it is a well-known result that the channel singular value decomposition (SVD) based linear precoding and decoding achieves the channel capacity, which also diagonalizes the MIMO channel into parallel single-input single-output (SISO) sub-channels for independent encoding and decoding. However, in multi-user MIMO systems, the optimal transmit covariance of each MIMO link is generally not its channel SVD based as a r…
The problem of joint design of transmit waveforms and receive filters is desirable in many application scenarios of multiple-input multiple-output (MIMO) radar systems. In this paper, the joint design problem is investigated under the signal-to-interference-plus-noise ratio (SINR) performance metric, in which case the problem is formulated to maximize the SINR at the receiver side subject to some practical transmit waveform constraints. A numerical algorithm is proposed for problem resolution based on the manifold optimization method, which has been shown to be powerful and flexible to address…
The stringent requirements on reliability and processing delay in the fifth-generation ($5$G) cellular networks introduce considerable challenges in the design of massive multiple-input-multiple-output (M-MIMO) receivers. The two main components of an M-MIMO receiver are a detector and a decoder. To improve the trade-off between reliability and complexity, a Bayesian concept has been considered as a promising approach that enhances classical detectors, e.g. minimum-mean-square-error detector. This work proposes an iterative M-MIMO detector based on a Bayesian framework, a parallel interference…
In this work, we study the performance of a single relay Multiple Input Multiple Output (MIMO) cooperative communication system based on Decode and Forward (DF) relaying protocol for two strategies using transmit antenna selection at the source. The first strategy uses one antenna between the relay and the destination, and the second strategy uses Space Time Block Coding (STBC). All channels follow the Rayleigh fading distribution. We derive the expression and Upper Bound for Symbol Error Rate (SER) for M-ary Phase Shift Keying (M-PSK), and the diversity order for both strategies. The analytic…
In order to improve the accuracy and resolution for transmit beamspace multiple-input multiple-output (MIMO) radar, a search-free direction-of-arrival (DOA) estimation method based on tensor decomposition and polynomial rooting is proposed. In the proposed method, a 3-order tensor is firstly designed to model the received signal of MIMO radar on the basis of the multi-linear property. Then, the factor matrix with target DOA information is obtained by the tensor decomposition via alternating least squares (ALS) algorithm, and subsequently the DOA estimation is converted into the independent min…
Precoding is a method of compensating the channel at the transmitter. This work presents a novel method of data detection in turbo coded single user massive multiple input multiple output (MIMO) systems using precoding. We show via computer simulations that, when precoding is used, re-transmitting the data does not result in significant reduction in bit-error-rate (BER), thus increasing the spectral efficiency, compared to the case without precoding. Moreover, increasing the number of transmit and receive antennas results in improved BER.
Multiple-input multiple-output (MIMO) systems are required to communicate reliably at high spectral bands using a large number of antennas, while operating under strict power and cost constraints. In order to meet these constraints, future MIMO receivers are expected to operate with low resolution quantizers, namely, utilize a limited number of bits for representing their observed measurements, inherently distorting the digital representation of the acquired signals. The fact that MIMO receivers use their measurements for some task, such as symbol detection and channel estimation, other than r…
Much stringent reliability and processing latency requirements in ultra-reliable-low-latency-communication (URLLC) traffic make the design of linear massive multiple-input-multiple-output (M-MIMO) receivers becomes very challenging. Recently, Bayesian concept has been used to increase the detection reliability in minimum-mean-square-error (MMSE) linear receivers. However, the latency processing time is a major concern due to the exponential complexity of matrix inversion operations in MMSE schemes. This paper proposes an iterative M-MIMO receiver that is developed by using a Bayesian concept a…
A Gaussian multiple-input multiple-output (MIMO) wiretap channel model is considered. The input is a two-antenna transmitter, while the outputs are the legitimate receiver and an eavesdropper, both equipped with multiple antennas. All channels are assumed to be known. The problem of obtaining the optimal input covariance matrix that achieves secrecy capacity subject to a power constraint is addressed, and a closed-form expression for the secrecy capacity is obtained.
Real-world transceiver designs for multiple-input multiple-output (MIMO) wireless communication systems are affected by a number of hardware impairments that already appear at the transmit side, such as amplifier non-linearities, quantization artifacts, and phase noise. While such transmit-side impairments are routinely ignored in the data-detection literature, they often limit reliable communication in practical systems. In this paper, we present a novel data-detection algorithm, referred to as large-MIMO approximate message passing with transmit impairments (short LAMA-I), which takes into a…
Physical layer security has been considered as an important security approach in wireless communications to protect legitimate transmission from passive eavesdroppers. This paper investigates the physical layer security of a wireless multiple-input multiple-output (MIMO) orthogonal frequency division multiplexing (OFDM) communication system in the presence of a multiple-antenna eavesdropper. We first propose a transmit-filter-assisted secure MIMO-OFDM system which can destroy the orthogonality of eavesdropper's signals. Our proposed transmit filter can disturb the reception of eavesdropper whi…
DOA estimation for massive multiple-input multiple-output (MIMO) system can provide ultra-high-resolution angle estimation. However, due to the high computational complexity and cost of all digital MIMO systems, a hybrid analog digital (HAD) structure MIMO was proposed. In this paper, a fast ambiguous phase elimination method is proposed to solve the problem of direction-finding ambiguity caused by the HAD MIMO. Only two-data-blocks are used to realize DOA estimation. Simulation results show that the proposed method can greatly reduce the estimation delay with a slight performance loss.
In this paper, the performance of an underlay multiple-input multiple-output (MIMO) cognitive radio system is analytically studied. In particular, the secondary transmitter operates in a spatial multiplexing transmission mode, while a zero-forcing detector is employed at the secondary receiver. Additionally, the secondary system is interfered by single-antenna primary users (PUs). To enhance the performance of secondary transmission, optimal power allocation is performed at the secondary transmitter with a constraint on the maximum allowable outage threshold specified by the PUs. Further, the …
In this paper, performance of a dual-hop cooperative multiple-input and multiple-output (MIMO) system is analyzed over Rayleigh faded channels. For the considered system model, non-regenerative MIMO scheme with transmit antenna selection strategy (TAS) is employed. In this scheme, a single transmit antenna which maximizes the total received signal power at the receiver is selected for transmission. Useful insights from average symbol error rate for various quadrature amplitude modulation (QAM) schemes such as general order hexagonal QAM (HQAM), general order rectangular QAM (RQAM) and 32-cross…
This paper proposes a communication model for multiuser multiple-input multiple-output (MIMO) systems based on large intelligent surfaces (LIS), where the LIS is modeled as a collection of tightly packed antenna elements. The LIS system is first represented in a circuital way, obtaining expressions for the radiated and received powers, as well as for the coupling between the distinct elements. Then, this circuital model is used to characterize the channel in a line-of-sight propagation scenario, rendering the basis for the analysis and design of MIMO systems. Due to the particular properties o…
We derive optimal SNR-based transmit antenna selection rules at the source and relay for the nonregenerative half duplex MIMO relay channel. While antenna selection is a suboptimal form of beamforming, it has the advantage that the optimization is tractable and can be implemented with only a few bits of feedback from the destination to the source and relay. We compare the bit error rate of optimal antenna selection at both the source and relay to other proposed beamforming techniques and propose methods for performing the necessary limited feedback.
Physical transceiver implementations for multiple-input multiple-output (MIMO) wireless communication systems suffer from transmit-RF (Tx-RF) impairments. In this paper, we study the effect on channel capacity and error-rate performance of residual Tx-RF impairments that defy proper compensation. In particular, we demonstrate that such residual distortions severely degrade the performance of (near-)optimum MIMO detection algorithms. To mitigate this performance loss, we propose an efficient algorithm, which is based on an i.i.d. Gaussian model for the distortion caused by these impairments. In…
Due to the large power consumption in RF-circuitry of massive MIMO systems, practically relevant performance measures such as energy efficiency or bandwidth efficiency are neither necessarily monotonous functions of the total transmit power nor the number of active antennas. Optimal antenna selection is however computationally infeasible in these systems. In this paper, we propose an iterative algorithm to optimize the transmit power and the subset of selected antennas subject to non-monotonous performance measures in massive multiuser MIMO settings. Numerical results are given for energy effi…
Massive multiple-input-multiple-output (M-MIMO) features a capability for spatial multiplexing of large number of users. This number becomes even more extreme in extra-large (XL-MIMO), a variant of M-MIMO where the antenna array is of very large size. Yet, the problem of signal processing complexity in M-MIMO is further exacerbated by the XL size of the array. The basic processing problem boils down to a sparse system of linear equations that can be addressed by the randomized Kaczmarz (RK) algorithm. This algorithm has recently been applied to devise low-complexity M-MIMO receivers; however, …
This paper studies the interference channel with two transmitters and two receivers in the presence of a MIMO relay in the low transmit power regime. A communication scheme combining block Markov encoding, beamforming, and Willems' backward decoding is used. With this scheme, we get an interference channel with channel gains dependent on the signal power. A power allocation for this scheme is proposed, and the achievable rate region with this power allocation is given. We show that, at low transmit powers, with equal power constraints at the relay and the transmitters, the interference channel…
Hybrid analog-digital architectures are considered as promising candidates for implementing millimeter wave (mmWave) massive multiple-input multiple-output (MIMO) systems since they enable a considerable reduction of the required number of costly radio frequency (RF) chains by moving some of the signal processing operations into the analog domain. However, the analog feed network, comprising RF dividers, combiners, phase shifters, and line connections, of hybrid MIMO architectures is not scalable due to its prohibitively high power consumption for large numbers of transmit antennas. Motivated …
In this paper, we obtain the scaling laws of the sum-rate capacity of a MIMO X-channel, a 2 independent sender, 2 independent receiver channel with messages from each transmitter to each receiver, at high signal to noise ratios (SNR). The X-channel has sparked recent interest in the context of cooperative networks and it encompasses the interference, multiple access, and broadcast channels as special cases. Here, we consider the case with partially cooperative transmitters in which only partial and asymmetric side-information is available at one of the transmitters. It is proved that when ther…
Conventional hybrid analog-digital architectures for millimeter-wave massive multiple-input multiple-output (MIMO) systems suffer from poor scalability and high implementational costs. The former is caused by the high power loss in the analog network, and the latter is due to the fact that classic MIMO transmission techniques require power amplifiers with high back-offs. This paper proposes a novel hybrid analog-digital architecture which addresses both of these challenges. This architecture implements the analog front-end via a passive reflect- or transmit-array to resolve the scalability iss…
A joint robust transmit/receive adaptive beamforming for multiple-input multipleoutput (MIMO) radar based on probability-constrained optimization approach is developed in the case of Gaussian and arbitrary distributed mismatch present in both the transmit and receive signal steering vectors. A tight lower bound of the probability constraint is also derived by using duality theory. The formulated probability-constrained robust beamforming problem is nonconvex and NP-hard. However, we reformulate its cost function into a bi-quadratic function while the probability constraint splits into transmit…
We analyze the diversity gain for a distributed antenna subarray employing orthogonal frequency-division multiplexing (OFDM) in millimeter-wave (mm-Wave) massive multiple-input multiple-output (MIMO) systems. We show that the diversity gain depends on the number of transmitted data streams, the number of remote antenna units, and the number of propagation paths between RAUs. Furthermore, we show that by using bit-interleaved coded multiple beamforming (BICMB), one can achieve the maximum diversity gain in a distributed antenna subarray system. The assumption in both scenarios is that the numbe…
Characterizing the fundamental energy efficiency (EE) limits of MIMO broadcast channels (BC) is significant for the development of green wireless communications. We address the EE optimization problem for MIMO-BC in this paper and consider a practical power model, i.e., taking into account a transmit independent power which is related to the number of active transmit antennas. Under this setup, we propose a new optimization approach, in which the transmit covariance is optimized under fixed active transmit antenna sets, and then active transmit antenna selection (ATAS) is utilized. During the …
Co-Designing Statistical MIMO Radar and In-band Full-Duplex Multi-User MIMO Communications -- Part II: Joint Precoder, Radar Code, and Receive Filters Design
Multiple antenna systems have been extensively used by standards designing multi-gigabit communication systems operating in bandwidth of several GHz. In this paper, we study the use of transmitter (Tx) beamforming techniques to improve the performance of a MIMO system with a low precision ADC. We motivate an approach to use eigenmode transmit beamforming (which imposes a diagonal structure in the complete MIMO system) and use an eigenmode power allocation which minimizes the uncoded BER of the finite precision system. Although we cannot guarantee optimality of this approach, we observe that ev…
Multiple input multiple output (MIMO) system transmission is a popular diversity technique to improve the reliability of a communication system where transmitter, communication channel and receiver are the important elements. Data transmission reliability can be ensured when the bit error rate is very low. Normally, multiple antenna elements are used at both the transmitting and receiving section in MIMO Systems. MIMO system utilizes antenna diversity or spatial diversity coding system in wireless channels because wireless channels severely suffer from multipath fading in which the transmitted…
This paper considers a deterministic physical model of massive multiple-input multiple-output (MIMO) systems with uniform linear antenna arrays. It is known that the maximum spatial degrees of freedom is achieved by spacing antenna elements at half the carrier wavelength. The purpose of this paper is to investigate the impacts of spacing antennas more densely than the critical separation. The achievable rates of MIMO systems are evaluated in the large-system limit, where the lengths of transmit and receive antenna arrays tend to infinity with the antenna separations kept constant. The main res…
Beam-space MIMO has recently been proposed as a promising solution to enable transmitting multiple data streams using a single RF chain and a single pattern-reconfigurable antenna. Since in a beam-space MIMO system radiation pattern of the transmit antenna is exploited as extra dimension for encoding information, near-field interaction of the transmit antenna with its surrounding objects affects spatial multiplexing performance of the system. Through numerical simulations in the previous work, it has been concluded that under BPSK signaling beam-space MIMO is not more vulnerable to near-field …
The combination of orthogonal frequency modulation (OFDM) and multiple-input multiple-output (MIMO) systems plays an important role in modern communication systems. In order to meet the growing throughput demands, future MIMO-OFDM receivers are expected to utilize a massive number of antennas, operate in dynamic environments, and explore high frequency bands, while satisfying strict constraints in terms of cost, power, and size. An emerging technology to realize massive MIMO receivers of reduced cost and power consumption is based on dynamic metasurface antennas (DMAs), which inherently implem…
This paper is concerned with a wireless system operating in MIMO fading channels with channel state information being known at both transmitter and receiver. By spatiotemporal subchannel selection and power control, it aims to minimize the average transmit power (ATP) of the MIMO system while achieving an exponential type of average bit error rate (BER) for each data stream. Under the constraints of a given fixed individual outage probability (OP) and average BER for each subchannel, based on a traditional upper bound and a dynamic upper bound of Q function, two closed-form ATP expressions are…
In this letter, we investigate the performance of multiple-input multiple-output techniques in a vehicle-to-vehicle communication system. We consider both transmit antenna selection with maximal-ratio combining and transmit antenna selection with selection combining. The channel propagation model between two vehicles is represented as n*Rayleigh distribution, which has been shown to be a realistic model for vehicle-to-vehicle communication scenarios. We derive tight analytical expressions for the outage probability and amount of fading of the post-processing signal-to-noise ratio.
Multiple input multiple output techniques are considered attractive for future wireless communication systems, due to the continuing demand for high data rates, spectral efficiency, suppress interference ability and robustness of transmission. MIMO-OFDM is very helpful to transmit high data rate in wireless transmission and provides good maximum system capacity by getting the advantages of both MIMO and OFDM. The main problem in this system is that increase in number of transmit and receive antennas lead to hardware complexity. To tackle this issue, an effective optimal transmit antenna subset…
We propose a joint discrete stochastic optimization based transmit diversity selection (TDS) and relay selection (RS) algorithm for decode-and-forward (DF), cooperative MIMO systems with a non-negligible direct path. TDS and RS are performed jointly with continuous least squares channel estimation (CE), linear minimum mean square error (MMSE) receivers are used at all nodes and no inter-relay communication is required. The performance of the proposed scheme is evaluated via bit-error rate (BER) comparisons and diversity analysis, and is shown to converge to the optimum exhaustive solution.
Diversity order is an important measure for the performance of communication systems over MIMO fading channels. In this paper, we prove that in MIMO multiple access systems (or MIMO point-to-point systems with V-BLAST transmission), lattice-reduction-aided decoding achieves the maximum receive diversity (which is equal to the number of receive antennas). Also, we prove that the naive lattice decoding (which discards the out-of-region decoded points) achieves the maximum diversity.
Correlation across transmit antennas, in multiple antenna systems (MIMO), has been studied in various scenarios and has been shown to be detrimental or provide benefits depending on the particular system and underlying assumptions. In this paper, we investigate the effect of transmit correlation on the capacity of the Gaussian MIMO broadcast channel (BC), with a particular interest in the large-scale array (or massive MIMO) regime. To this end, we introduce a new type of diversity, referred to as transmit correlation diversity, which captures the fact that the channel vectors of different user…
We propose a unitary precoding scheme, namely polar-precoding, to improve the performance of polar-coded MIMO systems. In contrast to the traditional design of MIMO precoding criteria, the proposed polar-precoding scheme relies on the \emph{polarization criterion}. In particular, the precoding matrix design comprises two steps. After selecting a basic matrix for maximizing the capacity in the first step, we design a unitary matrix for maximizing the polarization effect among the data streams without degrading the capacity. Our simulation results show that the proposed polar-precoding scheme ou…
In this paper, we derive an ambiguity function (AF) for the transmit beamspace (TB)-based multipleinput multiple-output (MIMO) radar for the case of far-field targets and narrow-band waveforms. The effects of transmit coherent processing gain and waveform diversity are incorporated into the AF definition. To cover all the phase information conveyed by different factors, we introduce the equivalent transmit phase centers. The newly defined AF serves as a generalized AF form for which the phased-array (PA) and traditional MIMO radar AFs are important special cases. We establish relationships amo…
In this paper, we propose algorithms for signal detection in large-scale multiuser {\em spatial modulation multiple-input multiple-output (SM-MIMO)} systems. In large-scale SM-MIMO, each user is equipped with multiple transmit antennas (e.g., 2 or 4 antennas) but only one transmit RF chain, and the base station (BS) is equipped with tens to hundreds of (e.g., 128) receive antennas. In SM-MIMO, in a given channel use, each user activates any one of its multiple transmit antennas and the index of the activated antenna conveys information bits in addition to the information bits conveyed through …
A contemporary perspective on the tradeoff between transmit antenna diversity and spatial multiplexing is provided. It is argued that, in the context of most modern wireless systems and for the operating points of interest, transmission techniques that utilize all available spatial degrees of freedom for multiplexing outperform techniques that explicitly sacrifice spatial multiplexing for diversity. In the context of such systems, therefore, there essentially is no decision to be made between transmit antenna diversity and spatial multiplexing in MIMO communication. Reaching this conclusion, h…
In this paper, we study multiple-input multiple-output (MIMO) wireless power transfer (WPT) systems, where the energy harvester (EH) node is equipped with multiple nonlinear rectennas. We characterize the optimal transmit strategy by the optimal distribution of the transmit symbol vector that maximizes the average harvested power at the EH subject to a constraint on the power budget of the transmitter. We show that the optimal transmit strategy employs scalar unit-norm input symbols with arbitrary phase and two beamforming vectors, which are determined as solutions of a non-convex optimization…
In this paper, we investigate the capacity of massive multiple-input multiple-output (MIMO) systems corrupted by complex-valued additive white Gaussian noise (AWGN) when both the transmitter and the receiver employ 1-bit digital-to-analog converters (DACs) and 1-bit analog-to-digital-converters (ADCs). As a result of 1-bit DACs and ADCs, the transmitted and received symbols, as well as the transmit- and receive-side channel state information (CSI), are assumed to be quantized to 1-bit of information. The derived results show that the capacity of the considered massive MIMO system is $2N$ and $…
We determine the capacity-achieving input covariance matrices for coherent block-fading correlated MIMO Rician channels. In contrast with the Rayleigh and uncorrelated Rician cases, no closed-form expressions for the eigenvectors of the optimum input covariance matrix are available. Both the eigenvectors and eigenvalues have to be evaluated by using numerical techniques. As the corresponding optimization algorithms are not very attractive, we evaluate the limit of the average mutual information when the number of transmit and receive antennas converge to infinity at the same rate. If the chann…
Cyclic prefix (CP) based MIMO-OFDM radar has been recently proposed for distributed transmit antennas, where there is no inter-range-cell interference (IRCI). It can collect full spatial diversity and each transmitter transmits signals with the same frequency band, i.e., the range resolution is not reduced. However, it needs to transmit multiple OFDM pulses consecutively to obtain range profiles for a single swath, which may be too long in time for a reasonable swath width. In this letter, we propose a CP based MIMO-OFDM synthetic aperture radar (SAR) system, where each transmitter transmits o…
In this paper, we propose a new multiple-input multiple-output (MIMO) communication system with movable antennas (MAs) to exploit the antenna position optimization for enhancing the capacity. Different from conventional MIMO systems with fixed-position antennas (FPAs), the proposed system can flexibly change the positions of transmit/receive MAs, such that the MIMO channel between them is reconfigured to achieve higher capacity. We aim to characterize the capacity of MA-enabled point-to-point MIMO communication systems, by jointly optimizing the positions of transmit and receive MAs as well as…
Orthogonality is a much desired property for MIMO coding. It enables symbol-wise decoding, where the errors in other symbol estimates do not affect the result, thus providing an optimality that is worth pursuing. Another beneficial property is a low complexity soft decision decoder, which for orthogonal complex MIMO codes is known for two transmit (Tx) antennas i.e. for the Alamouti code. We propose novel soft decision decoders for the orthogonal complex MIMO codes on three and four Tx antennas and extend the old result of maximal ratio combining (MRC) to cover all orthogonal codes up to four …
