This study examines the mechanical behavior of a novel class of mechanical metamaterials alternating pentamode lattices and stiffening plates. The unit cell of such lattices consists of a sub-lattice of the face cubic-centered unit cell typically analyzed in the current literature on pentamode materials. The studied systems exhibit only three soft deformation modes in the infinitesimal stretch-dominated regime, as opposed to the five zero-energy modes of unconfined pentamode lattices. We develop analytical formulae for the vertical and bending stiffness properties and study the dependence of such quantities on the main design parameters: the lattice constant, the solid volume fraction, the cross-section area of the rods, and the layer thickness. A noteworthy result is that the effective compression modulus of the analyzed structures is equal to two thirds of the Young modulus of the stiffest isotropic elastic networks currently available in the literature, being accompanied by zero-rigidity against infinitesimal shear and twisting mechanisms. The use of the proposed metamaterials as novel seismic-isolation devices and impact-protection equipment is discussed by drawing comparisons with the response of alternative devices already available or under development.
Pentamode metamaterials are a type of extremal designer metamaterials which are able to demonstrate high rigidity in one direction and extremely high compliance in other directions. Pentamodes can, therefore, be considered as building blocks of exotic materials with any arbitrarily selected thermodynamically admissible elasticity tensor. The pentamode lattices can then be envisioned to be combined to construct intermediate extremal materials such as quadramodes, trimodes, and bimodes. In this study, we constructed several primary types of anisotropic pentamode lattices (with midpoint positioni…
A numerical study on the elastic response of single- and multi-layer systems formed by alternating pentamode lattices and stiffening plates is presented. Finite element simulations are conducted to analyze the dependence of the effective elastic moduli of such structures upon suitable aspect ratios, which characterize the geometry of the generic pentamode layer at the micro- and macro-scale, and the lamination scheme of the layered structure. The given numerical results highlight that the examined structures exhibit bending-dominated response, and are able to achieve low values of the effectiv…
In this paper, we employ the novel design of the metamaterial half-wave plate by using the multiple layers of the metamaterials with some specific rotation angles. The rotation angles are given by composite pulse control which is the well-known quantum control technique. A big advantage of this method can analytically calculate the rotation angles and can be easily extended to the multiple layers. The more layers of the metamaterials can present more bandwidth of half-wave plate. In this paper, we present 1, 3, 5, 7 configurations of layers of a metamaterial half-wave plate and we demonstrate …
In this paper, a novel design concept for active self-adaptive metamaterial (ASAMM) plates is proposed based on an active self-adaptive (ASA) control strategy guided by the particle swarm optimization (PSO) technique. The ASAMM plates consist of an elastic base plate and two periodic arrays of piezoelectric patches. The periodic piezoelectric patches place on the bottom plate surface act as sensors, while the other ones attached on the top plate surfaces act as actuators. A simplified plate model is established by the Hamilton principle. By assuming a uniform or constant plate thickness, the p…
In this paper, we present numerical and experimental evidence of directional wave behavior, i.e. beaming and diffraction, along high-order rotational symmetries of quasicrystalline elastic metamaterial plates. These structures are obtained by growing pillars on an elastic plate following a particular rotational symmetry arrangement, such as 8-fold and 10-fold rotational symmetries, as enforced by a design procedure in reciprocal space. We estimate the dispersion properties of the waves propagating in the plates through Fourier transformation of transient wave-fields. The procedure identifies, …
Piezoelectric elastic metamaterials offer the ability to overcome the fixed, narrow bandwidth characteristics of passive elastic metamaterials. Interesting ultrasonic band gaps exist in piezoelectric plate metamaterials with periodic electrodes connected to shunted circuits. These band gaps result from an avoided crossing between electrical and mechanical bands, and can arise at lower frequencies than Bloch wave band gaps. Current analytical modeling techniques for these systems are numerically cumbersome, and assume an infinitely periodic plate. We present an approximate two-dimensional analy…
We report the realization of simultaneously negative effective mass density and shear modulus in a single-phase asymmetric double-sided pillared metamaterial. The negative effective mass density is achieved by the combination of bending and compressional resonances of one pillar whereas the rotational resonance of the other pillar leads to the negative effective shear modulus. The coupling between these two pillars is investigated to describe the formation of the doubly negative property. Then, a pillared system featuring chirality is designed in order to make efficient the excitation of the r…
This paper investigates the pseudo-spin based edge states for flexural waves in a honeycomb perforated phononic plate, which behaves an elastic analogue of the quantum spin Hall effect. We utilize finite element method to analyse the dispersion for flexural waves based on Mindlin's plate theory. Topological transition takes place around a double Dirac cone at $Γ$ point by adjusting the sizes of perforated holes. We develop an effective Hamiltonian to describe the bands around the two doubly degenerated states and analyse the topological invariants. This further leads us to observe the topologi…
A zero-frequency seismic metamaterial (ZFSM) consisting of a three-component seismic metamaterial plate and a half space is proposed to attenuate ultra-low frequency seismic surface waves. The design concept and models are verified firstly by lab-scale experiments on the seismic metamaterial consisting of a two-component seismic metamaterial plate and a half space. Then we calculate the band structures of the one-dimensional and two-dimensional ZFSMs, and evaluate their attenuation ability to Rayleigh waves. A wide band gap and a zero-frequency band gap (ZFBG) can be found as the band structur…
A novel design of an elastic metamaterial with anisotropic mass density is proposed to manipulate flexural waves at a subwavelength scale. The three-dimensional metamaterial is inspired by kirigami, which can be easily manufactured by cutting and folding a thin metallic plate. By attaching the resonant kirigami structures periodically on the top of a host plate, a metamaterial plate can be constructed without any perforation that degrades the strength of the pristine plate. An analytical model is developed to understand the working mechanism of the proposed elastic metamaterial and the dispers…
Wave Focusing in Metamaterials: Tactile Displays Beyond the Diffraction Limit
Media Arts and Technology Program（媒体艺术与技术项目）；Department of Mechanical Engineering（机械工程系）；Department of Electrical and Computer Engineering（电气与计算机工程系）；University of California, Santa Barbara（加州大学圣芭芭拉分校）
In this paper, we present a unit cell showing a band-gap in the lower acoustic domain. The corresponding metamaterial is made up of a periodic arrangement of this unit cell. We rigorously show that the relaxed micromorphic model can be used for metamaterials' design at large scales as soon as suficiently large specimens are considered. We manufacture the metamaterial via metal etching procedures applied to a titanium plate so as to show that its production for realistic applications is viable. Experimental tests are also carried out confirming that the metamaterials' response is in good agreem…
The unusual viscoelastic properties of silica aerogel plates are efficiently used to design subwavelength perfect sound absorbers. We theoretically, numerically and experimentally report a perfect absorbing metamaterial panel made of periodically arranged resonant building blocks consisting of a slit loaded by a clamped aerogel plate backed by a closed cavity. The impedance matching condition is analyzed using the Argand diagram of the reflection coefficient, i.e., the trajectory of the reflection coefficient as a function of frequency in the complex plane. The lack or excess of losses in the …
We develop a fast, accurate, and robust technique to model the electromagnetic response of a two-dimensional (2D) waveguide-fed metasurface aperture. The geometry under consideration consists of a parallel-plate waveguide with an array of subwavelength, complementary metamaterial elements patterned into one of the conducting surfaces. To determine the radiated field, we model each radiating element as a polarizable dipole, and account for mutual interactions among elements via guided and radiated fields by applying a coupled dipole framework. Using full-wave simulations of parallel-plate waveg…
Phononic crystals and metamaterials take advantage of pre-designed geometrical structures to sculpt elastic waves, controlling their dispersion using different mechanisms. These mechanisms revolve mostly around Bragg scattering (BS), local resonances (LR) and inertial amplification (IA), which employ ad-hoc, often problem-specific geometries. Here, we use parametrized, spiraling unit cells as building blocks for designing various types of phononic materials. We focus on planar spirals that are easy to fabricate, yet give rise to the desirable complex dynamics. By simple modifications of the sp…
