The study reports the aspects of postimpact hydrodynamics of ferrofluid droplets on superhydrophobic SH surfaces in the presence of a horizontal magnetic field. A wide gamut of dynamics was observed by varying the impact Weber number We, the Hartmann number Ha and the magnetic field strength manifested through the magnetic Bond number Bom. For a fixed We 60, we observed that at moderately low Bom 300, droplet rebound off the SH surface is suppressed. The noted We is chosen to observe various impact outcomes and to reveal the consequent ferrohydrodynamic mechanisms. We also show that ferrohydrodynamic interactions leads to asymmetric spreading, and the droplet spreads preferentially in a direction orthogonal to the magnetic field lines. We show analytically that during the retraction regime, the kinetic energy of the droplet is distributed unequally in the transverse and longitudinal directions due to the Lorentz force. This ultimately leads to suppression of droplet rebound. We study the role of Bom at fixed We 60, and observed that the liquid lamella becomes unstable at the onset of retraction phase, through nucleation of holes, their proliferation and rupture after reaching a critical thickness only on SH surfaces, but is absent on hydrophilic surfaces. We propose an analytical model to predict the onset of instability at a critical Bom. The analytical model shows that the critical Bom is a function of the impact We, and the critical Bom decreases with increasing We. We illustrate a phase map encompassing all the post impact ferrohydrodynamic phenomena on SH surfaces for a wide range of We and Bom.
Over the past few decades, superhydrophobic materials have attaracted a lot of interests, due to their numerous practical applications. Among various superhydrophobic materials, carbon nanotube arrays have gained enormous attentions simply because of their outstanding properties. The impact dynamic of water droplet on a superhydrophobic carbon nanotube array is shown in this fluid dynamics video.
This fluid dynamics video describes droplet impingement experiments performed on superhydrophobic surfaces. When droplets of pure water are impinged upon superhydrophobic surfaces, a region of thin coherent jets are observed for Weber numbers between 5 and 15. Also, peripheral splashing is observed for Weber numbers above about 200. When the viscosity of the droplet is increased by mixing glycerol with the water, the thin jets are not observed and peripheral splashing is delayed somewhat. In the Weber number range where pure water droplets are observed to splash peripherally, the water/glycero…
The article demonstrates that the internal circulation velocity and patterns in sessile droplets on superhydrophobic surfaces is governed by the surface curvature. Particle Image Velocimetry reveals that increasing convexity deteriorates the advection velocity whereas concavity augments it. A scaling model based on the effective curvature modulated change in wettability can predict the phenomenon, but weakly. Potential flow theory is appealed to and the curvatures are approximated as wedges with the rested droplet engulfing them partly. The spatially averaged experimental velocities are found …
We introduce a droplet-jumping phenomenon on a superhydrophobic surface driven by the resonant AC electrowetting. The resonant electrical actuation enables a droplet to accumulate sufficient surface energy for jumping, and superhydrophobic surface minimizes adhesion and hysteresis effects. They provide the effective energy conversion from the surface energy to the kinetic energy and improve the stability and the reproducibility of the droplet jumping. The controlled droplet jumping made by the resonant AC electrowetting could place another milestone in digital microfluidics by establishing a p…
The leaves of many plants are superhydrophobic, a property that may have evolved to clean the leaves by encouraging water droplets to bead up and roll off. Superhydrophobic surfaces can also exhibit reduced friction and liquids flowing over such surfaces have been found to slip in apparent violations of the classical no-slip boundary condition. Here we introduce slip into a model for rolling droplets on superhydrophobic surfaces and investigate under what conditions slip might be important for the steady state motion. In particular, we examine three limiting cases where dissipation in the roll…
Evaporation of water droplets on a superhydrophobic substrate, on which the contact line is pinned, is investigated. While previous studies mainly focused on droplets with contact angles smaller than 90^\circ, here we analyze almost the full range of possible contact angles (10^\circ -150^\circ). The greater contact angles and pinned contact lines can be achieved by the use of superhydrophobic Carbon Nanofiber substrates. The time-evolutions of the contact angle and the droplet mass are examined. The experimental data is in good quantitative agreement with the model presented by Popov (Physica…
This is a fluid dynamics video illustrating the impact of ferrofluidic droplets on surfaces of variable wettability. Surfaces studied include mica, teflon, and superhydrophobic. A magnet is placed beneath each surface, which modifies the behavior of the ferrofluid by applying additional downward force apart from gravity resulting in reduced droplet size and increased droplet velocity. For the superhydrophobic droplet a jetting phenomena is shown which only occurs in a limited range of impact speeds, higher than observed before, followed by amplified oscillation due to magnetic field as the dro…
This fluid dynamics video depicts the evaporation of sessile water droplets placed on heated superhydrophobic (SH) surfaces of varying cavity fraction, F_c, and surface temperature, T_s, above the saturation temperature, T_sat. Images were captured at 10,000 FPS and are played back at 30 FPS in this video. Teflon-coated silicon surfaces of F_c = 0, 0.5, 0.8, and 0.95 were used for these experiments. T_s ranging from 110°C to 210°C were studied. The video clips show how the boiling behavior of sessile droplets is altered with changes in surface microstructure. Quantitative results from heat tra…
The Leidenfrost phenomenon entails the levitation of a liquid droplet over a superheated surface, cushioned by its vapor layer. For water, superhydrophobic surfaces are believed to suppress the Leidenfrost point ($\it{T}$$_{\rm L}$)-the temperature at which this phenomenon occurs. The vapor film obstructs boiling heat transfer in heat exchangers, thereby compromising energy efficiency and safety. Thus, it is desirable to realize superhydrophobicity without suppressing $\it{T}$$_{\rm L}$. Here we demonstrate that the $\it{T}$$_{\rm L}$ of water on microtextured superhydrophobic surfaces compris…
Macro-textured superhydrophobic surfaces can reduce droplet-substrate contact times of impacting water droplets, however, surface designs with similar performance for significantly more viscous liquids are missing, despite their importance in nature and technology such as for chemical shielding, food staining repellency, and supercooled (viscous) water droplet removal in anti-icing applications. Here, we introduce a deterministic, controllable and up-scalable method to fabricate superhydrophobic surfaces with a 3D-printed architecture, combining arrays of alternating surface protrusions and in…
We numerically investigate bouncing and non-bouncing of droplets during isothermal impact on superhydrophobic surfaces. An in-house, experimentally-validated, finite-element method based computational model is employed to simulate the droplet impact dynamics and transient fluid flow within the droplet. The liquid-gas interface is tracked accurately in Lagrangian framework with dynamic wetting boundary condition at three-phase contact line. The interplay of kinetic, surface and gravitational energies is investigated via systematic variation of impact velocity and equilibrium contact angle. The …
This paper reports the dynamic wetting behavior and heat transfer characteristics for impinging droplets on heated bi-phobic surfaces (superhydrophobic matrix with hydrophobic spots). A non-patterned superhydrophobic and a sticky hydrophobic surface acted as control wettability surfaces. As expected, differences in wetting and heat transfer dynamics were noticeable for all surfaces, with the most pronounced variation during the receding phase. During spreading, inertia from the impact dominated the droplet dynamics and heat transfer was dominated by convection at the contact line and internal …
There is a huge interest in developing super-repellent surfaces for anti-fouling and heat transfer applications. To characterize the wetting properties of such surfaces, the most common approach is to place a millimetric-sized droplet and measure its contact angles. The adhesion and friction forces can then be indirectly inferred from the Furmidge's relation. While easy to implement, contact angle measurements are semi-quantitative and cannot resolve wetting variations on a surface. Here, we attach a micrometric-sized droplet to an Atomic Force Microscope cantilever to directly measure adhesio…
Super hydrophobic surfaces have been the focus of research in the recent years.One of the reasons for this is the self cleaning property of these surfaces which emerges from the ability of the droplets to roll freely over them.However majority of the studies available in literature are on the static wetting behavior of liquid droplets on such surfaces and the physics of the motion of droplets has not been studied exhaustively either theoretically or experimentally.In the present study droplet motion on super hydrophobic surfaces has been modeled to analyze the sliding/ rolling characteristics …
Although realizing wetting transitions of droplets spontaneously on solid rough surfaces is quite challenging, it is becoming a key research topic in many practical applications which require highly efficient removal of liquid. We report wetting transitions of condensed droplets occurring spontaneously on pillared surfaces with two-tier roughness owing to excellent superhydrophobicity. The phenomenon results from further decreased Laplace pressure on the top side of the individual droplet when its size becomes comparable to the scale of the micropillars, which leads to a surprising robust spon…
This fluid dynamics video shows the different interaction mechanisms of coalescence-induced droplet jumping during condensation on a nanostructured superhydrophobic surface. High speed imaging was used to show jumping behavior on superhydrophobic copper oxide and carbon nanotube surfaces. Videos demonstrating multi-jumping droplets, jumping droplet return to the surface, and droplet-droplet electrostatic repulsions were analyzed. Experiments using external electric fields in conjunction with high speed imaging in a custom built experimental chamber were used to show that all coalescence-induce…
Droplet deposition after impact on superhydrophobic surfaces has been an important area of study in recent years due to its potential application in reduction of pesticides usage. Minute amounts of long chain polymers added to water has been known to arrest the droplet rebound effect on superhydrophobic surfaces. Previous studies have attributed different reasons like extensional viscosity, dominance of elastic stresses or slowing down of contact line in retraction phase due to stretching of polymer chains. The present study attempts to unravel the existence of critical criteria of polymer con…
The video exhibits experimental qualitative and quantitative results of water/glycerol (50%/50% by mass) droplet impact on two types of micro-patterned superhydrophobic surfaces. The two types of surfaces used were 80% cavity fraction ribs and posts with a periodic spacing of 40 μm and 32 μm, respectively. All surfaces were manufactured through photolithography. The impact Weber number is used as the dynamic parameter to compare splash and rebound behaviors between the two types of surfaces. While droplets exhibit similar dynamics at low Weber numbers, rebound jet speed (normalized by droplet …
Because the superhydrophobic characteristic appears by forming a composite surface consisting of solid and air underneath the droplets, a large number of rough surfaces that can trap air have been fabricated. Recently, the air trapping on materials whose equilibrium contact angles are less than 90 degrees was achieved by fabricating proper structures that lead energetic stability at the condition. Whereas these methods were proposed under the assumption of the static and equilibrium conditions, we take a dynamic and non-equilibrium approach in this study through droplet deposition and droplet …
We have fabricated and characterized a novel superhydrophobic system, a mesh-like porous superhydrophobic membrane with solid area fraction $Φ_s$, which can maintain intimate contact with outside air and water reservoirs simultaneously. Oscillatory hydrodynamic measurements on porous superhydrophobic membranes as a function of $Φ_s$ reveal surprising effects. The hydrodynamic mass oscillating in-phase with the membranes stays constant for $0.9\leΦ_s\le1$, but drops precipitously for $Φ_s < 0.9$. The viscous friction shows a similar drop after a slow initial decrease proportional to $Φ_s$. We a…
We study here the microscopic deformations of elastic lamellae constituting a superhydrophobic substrate under different wetting conditions of a sessile droplet using electrowetting. The deformation profiles of the lamellae are experimentally evaluated using confocal microscopy. These experimental results are then explained using a variational principle formalism within the framework of linear elasticity. We show that the local deformation profile of a lamella is mainly controlled by the net horizontal component of the capillary forces acting on its top due to the pinned droplet contact line. …
Superhydrophobic Cassie textures with trapped gas bubbles reduce drag, by generating large effective slip, which is important for a variety of applications that involve a manipulation of liquids at the small scale. Here we discuss how the dissipation in the gas phase of textures modifies their friction properties. We propose an operator method, which allows us the mapping of the flow in the gas subphase to a local slip boundary condition at the liquid/gas interface. The determined uniquely local slip length depends on the viscosity contrast and underlying topography, and can be immediately use…
We investigate directly at the microscale the morphology of the electrowetting induced transition between the Cassie-Baxter and Wenzel states for a water droplet on a superhydrophobic surface. Our experiments demonstrate that the transition originates in a very narrow annular region near the macroscopic contact line, which is first invaded by water and causes a thin film of air to be entrapped below. At high applied voltages, a growing fraction of microscopic air-pockets collapse, resulting in a partialWenzel state. Modulations in the intensity of the light reflected from individual micro-meni…
In this fluid dynamics video we show the trick played by a supercooled liquid water drop against a superhydrophobic surface. The water drop shows a double personality, impacting onto the surface the first time while still in the liquid state, and then re-impacting as a frozen ice crystal.
The superhydrophobic leaves of a lotus plant and other natural surfaces with self-cleaning function have been studied intensively for the development of artificial biomimetic surfaces. Surface roughness generated by hierarchical structures is a crucial property required for superhydrophobicity and self-cleaning. Here, we demonstrate a novel self-cleaning mechanism of textured surfaces attributed to a spontaneous coalescence-induced wetting transition. We focus on the wetting transition as it represents a new mechanism, which can explain why droplets on rough surfaces are able to change from th…
The present article experimentally and theoretically probes the evaporation kinetics of sessile saline droplets. Observations reveal that presence of solvated ions leads to modulated evaporation kinetics, which is further a function of surface wettability. On hydrophilic surfaces, increasing salt concentration leads to enhanced evaporation rates, whereas on superhydrophobic surfaces, it first enhances and reduces with concentration. Also, the nature and extents of the evaporation regimes constant contact angle or constant contact radius are dependent on the salt concentration. The reduced evap…
This fluid dynamics video is an entry for the Gallery of Fluid Motion of the 65th Annual Meeting of the APS-DFD. This video shows behavior of condensing droplets on a lubricant impregnated surface and a comparison with a superhydrophobic surface. On impregnated surfaces, drops appear like UFOs hovering over a surface. The videos were recorded in an Environmental SEM and a specially built condensation rig.
We experimentally investigate drop impact dynamics onto different superhydrophobic surfaces, consisting of regular polymeric micropatterns and rough carbon nanofibers, with similar static contact angles. The main control parameters are the Weber number \We and the roughness of the surface. At small \We, i.e. small impact velocity, the impact evolutions are similar for both types of substrates, exhibiting Fakir state, complete bouncing, partial rebouncing, trapping of an air bubble, jetting, and sticky vibrating water balls. At large \We, splashing impacts emerge forming several satellite dropl…
We provide some general theoretical results to guide the optimization of transverse hydrodynamic phenomena in superhydrophobic channels. Our focus is on the canonical micro- and nanofluidic geometry of a parallel-plate channel with an arbitrary two-component (low-slip and high-slip) coarse texture, varying on scales larger than the channel thickness. By analyzing rigorous bounds on the permeability, over all possible patterns, we optimize the area fractions, slip lengths, geometry and orientation of the surface texture to maximize transverse flow. In the case of two aligned striped surfaces, v…
We study the slippage on hierarchical fractal superhydrophobic surfaces, and find an unexpected rich behavior for hydrodynamic friction on these surfaces. We develop a scaling law approach for the effective slip length, which is validated by numerical resolution of the hydrodynamic equations. Our results demonstrate that slippage does strongly depend on the fractal dimension, and is found to be always smaller on fractal surfaces as compared to surfaces with regular patterns. This shows that in contrast to naive expectations, the value of effective contact angle is not sufficient to infer the a…
Electric energy generation from falling droplets has seen a hundred-fold rise in efficiency over the past year. However, even these newest devices can only extract a small portion of the droplet energy. In this paper, we theoretically investigate the contributions of hydrodynamic and electric losses in limiting the efficiency of droplet electricity generators (DEG). Noting that the electro-mechanical energy conversion occurs during the recoil that immediately follows droplet impact, we identify three limits on existing droplet electric generators: (i) the impingement velocity is limited in ord…
Experimental investigations were carried out to elucidate the role of surface wettability and inclination on the post impact dynamics of droplets. Maximum spreading diameter and spreading time were found to decrease with increasing inclination angle and normal Weber number for superhydrophobic surfaces. The experiments on SH surfaces were found to be in excellent agreement with an existing analytical model, incorporated with the modifications for the oblique impact conditions. Energy ratios and elongation factor were also measured for different inclination angles. On inclined SH surfaces, diff…
Rapid and sustained condensate droplet departure from a surface is key towards achieving high heat transfer rates in condensation, a physical process critical to a broad range of industrial and societal applications. Despite progress in enhancing condensation heat transfer through inducing its dropwise mode with hydrophobic materials, sophisticated surface engineering methods that can lead to further enhancement of heat transfer are still highly desirable. Here, by employing a three-dimensional, multiphase computational approach, we present an effective out-of-plane biphilic surface topography…
Post impingement morphology and dynamics of water droplets on convex cylindrical surfaces has been explored experimentally. Droplet impact and post-impact feature studies have been conducted on hydrophillic and superhydrophobic cylindrical surfaces. Effects of the impact Weber number and target-to-drop diameter ratio have been studied. The post-impact hydrodynamics have been quantified using the wetting fraction, the spreading factor and nondimensional film thickness at the north pole of the target. The observations reveal that the wetting fraction and spread factor increases with an increase …
Droplet mobility under shear flows is important in a wide range of engineering applications, e.g., fog collection, and self-cleaning surfaces. For structured surfaces to achieve superhydrophobicity, the removal of stains adhered within the microscale surface features strongly determines the functional performance and durability. In this study, we numerically investigate the shear-induced mobility of the droplet trapped within porous surfaces. Through simulations covering a wide range of flow conditions and porous geometries, three droplet mobility modes are identified, i.e., the stick-slip, cr…
Recent experiments with droplets impacting a macro-textured superhydrophobic surfaces revealed new regimes of bouncing with a remarkable reduction of the contact time. We present here a comprehensive numerical study that reveals the physics behind these new bouncing regimes and quantify the role played by various external and internal forces that effect the dynamics of a drop impacting a complex surface. For the first time, three-dimensional simulations involving macro-textured surfaces are performed. Aside from demonstrating that simulations reproduce experiments in a quantitative manner, the…
Hydrodynamic collapse of a central air-cavity during the recoil phase of droplet impact on a superhydrophobic sieve leads to satellite-free generation of a single droplet through the sieve. Two modes of cavity formation and droplet ejection was observed and explained. The volume of the generated droplet scales with the pore size. Based on this phenomenon, we propose a new drop-on-demand printing technique. Despite significant advancements in inkjet technology, enhancement in mass-loading and particle-size have been limited due to clogging of the printhead nozzle. By replacing the nozzle with a…
There are currently three main classes of high-performance liquid-repellent surfaces: micro-/nano-structured lotus-effect superhydrophobic surfaces, flat surfaces grafted with 'liquid-like' polymer brushes, and various lubricated surfaces. Despite recent progress, the mechanistic understanding of the differences in droplet behavior on such surfaces is still under debate. We measured the dissipative force acting on a droplet moving on representatives of these classes at different velocities U = 0.01-1 mm/s using a cantilever force sensor with sub-uN accuracy, and correlated it to the contact li…
Unraveling the Interplay of Leaf Structure and Wettability: A Comparative Study on Superhydrophobic Leaves of Cassia tora, Adiantum capillus-veneris, and Bauhinia variegata
Phase change under reduced environmental pressures is key to understanding liquid discharge and propulsion processes for aerospace applications. A representative case is the sessile water droplets exposed to high vacuum, which experience complex phase change and transport phenomena that behave so differently than that under the atmosphere. Here, we demonstrate a previously unexplored aspect of the mechanism governing icing droplet self-launching from superhydrophobic surfaces when exposed to low pressures (~100 Pa). In contrast to the previously reported recalescence-induced local overpressure…
Modification and control over the vaporization kinetics of microfluidic droplets may have strong utilitarian implications in several scientific and technological applications. The article reports the control over the vaporization kinetics of pendent droplets under the influence of competing internal electrohydrodynamic and ferrohydrodynamic advection. Experimental and theoretical studies are performed and the morphing of vaporization kinetics of electrically conducting and paramagnetic fluid droplets using orthogonal electric and magnetic stimuli is established. Analysis of the observations re…
Deformation of liquid droplets by impingement induces Worthington jet in certain range of the impact velocity. Although the growth of the jet as well as its tip velocity is predicted from similar cases to the droplet impact, the mechanism of the jet generation is yet to be understood. In this study, high-speed visualization of the droplet impact on a superhydrophobic surface was conducted to understand the initiation of the jet generated by a collapse of an air cavity. Water droplets whose diameter are 2.0 mm and 3.0 mm were generated and the Weber number of the droplet was varied in a range o…
