Next generation telecommunication technologies would benefit from strong piezoelectric and ferroelectric response in materials that are compatible with nitride radio-frequency electronic devices. Ferroelectric oxides with perovskite structure have been used in sensors and actuators for half a century, and halide perovskites transformed photovoltaics research in the past decade, but neither of them is compatible with nitride semiconductors. Nitride perovskites, despite numerous computational predictions, have not been experimentally demonstrated and their properties remain unknown. Here we report the experimental realization of the first nitride perovskite: lanthanum tungsten nitride (LaWN3). Oxygen-free LaWN3 thin films in a polar perovskite structure are confirmed by spectroscopy, scattering, and microscopy techniques. Scanning probe measurements confirm a large piezoelectric response and strongly suggest ferroelectric behavior, making it the first stable nitride ferroelectric compound. These results should lead to integration of LaWN3 with nitride semiconductors for wireless telecommunication applications, while enabling synthesis of many other predicted nitride perovskites.
We review the role that first-principles calculations have played in understanding the effects of substrate-imposed misfit strain on epitaxially grown perovskite ferroelectric films. We do so by analyzing the case of BaTiO$_3$, complementing our previous publications on this subject with unpublished data to help explain in detail how these calculations are done. We also review similar studies in the literature for other perovskite ferroelectric-film materials.
We performed first principles calculations for epitaxially strained orthorhombic CaTiO$_3$. The computational results reveal the existence of a metastable ferroelectric phase at compressive strain with unexpected in-plane polarization. Symmetry analysis indicates that two distortion modes at the X point combine to induce the polarization, leading to characterization as a hybrid improper ferroelectric. Our work demonstrates a mechanism for improper ferroelectricity in simple perovskites without the need for symmetry lowering by layering or cation ordering.
Using first principles calculations we show that several alkali lead halides potentially present collective ferroelectric polarization. This should occur at least at the nanoscale; it could be detected macroscopically provided it is not concealed by lattice vibrations in the temperature range of stability of the cubic perovskite phase. For potassium lead halides and for alkali lead fluorides, remarkably, the ferroelectric behavior turns hyper-ferroelectric, suggesting a more robust ferroelectric polarization in spite of depolarization potentials induced by charge accumulation on surfaces or in…
We use a combination of symmetry arguments and first-principles calculations to explore the connection between structural distortions and ferroelectricity in the perovskite family of materials. We explain the role of octahedral rotations in suppressing ferroelectricity in these materials and show that, as the tolerance factor decreases, rotations alone cannot fully suppress ferroelectricity. Our results show that it is cation displacements (`hidden' in Glazer notation) that accompany the rotations, rather than the rotations themselves, that play the decisive role in suppressing ferroelectricit…
We used first-principles calculations to investigate the existence and origin of the ferroelectric in- stability in the ABF3 fluoro-perovskites. We find that many fluoro-perovskites have a ferroelectric instability in their high symmetry cubic structure, which is of similar amplitude to that commonly found in oxide perovskites. In contrast to the oxides, however, the fluorides have nominal Born effective charges, indicating a different mechanism for the instability. We show that the instability originates from ionic size effects, and is therefore in most cases largely insensitive to pressure a…
Two-dimensional (2D) ferroelectricity has attracted extensive attention since its discovery in the monolayers of van der Waals materials. Here we show that 2D ferroelectricity induced by octahedral rotation distortion is widely present in the perovskite bilayer system through first-principles calculations. The perovskite tolerance factor plays a crucial role in the lattice dynamics and ground-state structure of the perovskite monolayers and bilayers, thus providing an important indicator for screening this hybrid improper ferroelectricity. Generally, the ferroelectric switching via an orthorho…
There are two silver perovskite oxides: AgNbO3 and AgTaO3. AgNbO3 has a noncentrosymmetric group of Pmc21 at room temperature with a ferri-electric ordering of polarization. Such a ferri-electric state with small polarization can be changed into a ferroelectric state with very large polarization by a high electric field or by a chemical modification. The induced ferroelectric phase shows promising electromechanical response for applications in piezoelectric devices. In contrast, AgTaO3 is a quantum paraelectric, but ferroelectricity also can be induced through chemical substitution. The findin…
We report studies of ferroelectricity in ultra-thin perovskite films with realistic electrodes. The results reveal stable ferroelectric states in thin films less than 10 Åthick with polarization normal to the surface. Under short-circuit boundary conditions, the screening effect of realistic electrodes and the influence of real metal/oxide interfaces on thin film polarization are investigated. Our studies indicate that metallic screening from the electrodes is affected by the difference in work functions at oxide surfaces. We demonstrate this effect in ferroelectric PbTiO$_3$ and BaTiO$_3$ fil…
Doping ferroelectrics with carriers is often detrimental to polarization. This makes the design and discovery of metals that undergo a ferroelectric-like transition challenging. In this letter, we show from first principles that the oxygen octahedral rotations in perovskites are often enhanced by electron doping, and this can be used as a means to strengthen the structural polarization in certain hybrid-improper ferroelectrics -- compounds in which the polarization is not stabilized by the long range Coulomb interactions but is instead induced by a trilinear coupling to octahedral rotations. W…
Molecular Dynamics is applied to Ferroelectric Perovskites in the framework of a first-principles derived effective Hamiltonian (Zhong, Vanderbilt, Rabe, Phys. Rev. Lett. {\bf 73} (1994), 1861). The degrees of freedom, that obey the Newton equations of motion, are the local modes and the displacement modes. The Nose-Hoover method is implemented, as well as the Parinello-Rahman scheme to perform fixed temperature and fixed stress tensor simulations. This allows to study the thermodynamics of ferroelectric perovskites and to reproduce successfully the Monte Carlo results on phase transitions, po…
This article reviews the polarizability model and its applications to ferroelectric perovskite oxides. The motivation for the introduction of the model is discussed and nonlinear oxygen ion polarizability effects and their lattice dynamical implementation outlined. While a large part of this work is dedicated to results obtained within the self-consistent-phonon approximation (SPA), also nonlinear solutions of the model are handled which are of interest to the physics of relaxor ferroelectrics, domain wall motions, incommensurate phase transitions. The main emphasis is to compare the results o…
Molecular ferroelectrics have attracted increasing interests over the past decade due to mechanical flexibility, chemical diversity, environmental friendliness, easy-processing, and lightness. The performance of molecular ferroelectrics is approaching more and more competitive to their inorganic counterparts. Despite the chemical diversity and tunability of the molecular cations or anions, molecular ferroelectrics are not abundant. In particular, physical directed design principles for new discovery or performance optimization are still lacking. Here, through first-principles calculations, we …
The nitride semiconductor materials GaN, AlN, and InN, and their alloys and heterostructures have been investigated extensively in the last 3 decades, leading to several technologically successful photonic and electronic devices. Just over the past few years, a number of new nitride materials have emerged with exciting photonic, electronic, and magnetic properties. Some examples are 2D and layered hBN and the III-V diamond analog cBN, the transition metal nitrides ScN, YN, and their alloys (e.g. ferroelectric ScAlN), piezomagnetic GaMnN, ferrimagnetic Mn4N, and epitaxial superconductor/semicon…
Dabconium hybrid perovskites include a number of recently-discovered ferroelectric phases with large spontaneous polarisations. The origin of ferroelectric response has been rationalised in general terms in the context of hydrogen bonding, covalency, and strain coupling. Here we use a combination of simple theory, Monte Carlo simulations, and density functional theory calculations to assess the ability of these microscopic ingredients---together with the always-present through-space dipolar coupling---to account for the emergence of polarisation in these particular systems whilst not in other …
We have developed first-principles models, based on a general parametrization of the full potential-energy surface, to investigate the lattice-dynamical properties of perovskite oxides. We discuss the application of our method to prototypic ferroelectric PbTiO3, showing that its properties are drastically affected by a competition between structural instabilities. Indeed, we confirm previous indications that the destructive interaction between the ferroelectric and antiferrodistortive (involving rotations of the O6 octahedra) soft modes shifts PbTiO3's Curie temperature by hundreds of degrees.…
Ferroelectric perovskites have been ubiquitously applied in piezoelectric devices for decades, among which, eco-friendly lead-free (K,Na)NbO3-based materials have been recently demonstrated to be an excellent candidate for sustainable development. Molecular dynamics is a versatile theoretical calculation approach for the investigation of the dynamical properties of ferroelectric perovskites. However, molecular dynamics simulation of ferroelectric perovskites has been limited to simple systems, since the conventional construction of interatomic potential is rather difficult and inefficient. In …
We propose a device model that elucidates the role of domain walls in the photovoltaic effect in multi-domain ferroelectric perovskites. The model accounts for the intricate interplay between ferroelectric polarization, space charges, photo-generation and electronic transport. When applied to bismuth ferrite, results show a significant electric potential step across both 71-degree and 109-degree domain walls, which in turn contributes to the photovoltaic (PV) effect. We also find a strong correlation between polarization and oxygen octahedra tilts, which indicates the nontrivial role of the la…
We present a high-pressure x-ray diffuse scattering study of the ABO$_3$ ferroelectric perovskites BaTiO_3 and KNbO_3. The well-known diffuse lines are observed in all the phases studied. In KNbO_3, we show that the lines are present up to 21.8 GPa, with constant width and a slightly decreasing intensity. At variance, the intensity of the diffuse lines observed in the cubic phase of BaTiO_3 linearly decreases to zero at $\sim 11$ GPa. These results are discussed with respect to x-ray absorption measurements, which leads to the conclusion that the diffuse lines are only observed when the B atom…
X-ray photoelectron diffraction is used to directly probe the intra-cell polar atomic distortion and tetragonality associated with ferroelectricity in ultrathin epitaxial PbTiO3 films. Our measurements, combined with ab-initio calculations, unambiguously demonstrate non-centro-symmetry in films a few unit cells thick, imply that films as thin as 3 unit cells still preserve a ferroelectric polar distortion, and also show that there is no thick paraelectric dead layer at the surface.
The stability of high-symmetry $P4mm$ polar phase in eleven ferroelectric perovskite superlattices with the polar discontinuity is studied from first principles. In most superlattices, this phase exhibits either the ferroelectric or the antiferrodistortive instability, or both of them. The structure of the ground state and, for a number of systems, also of metastable phases in these superlattices is found. The spontaneous polarization and piezoelectric properties of superlattices are calculated. The appearance of high piezoelectric coefficients (up to 150-270 pC/N) in some superlattices is ass…
Using first-principles calculations, we estimated the impact of large applied electric E fields on the structural, dielectric, and ferroelectric properties of typical ferroelectrics. At large fields, the structural parameters change significantly, decreasing the strain between the different structural phases. This effect favours a polarization rotation model for ferroelectric switching in which the electronic polarization rotates between the directions of tetragonal, rhombohedral and orthorhombic phases. We estimate coercive fields E_c ~31 MV/m and ~52 MV/m at zero temperature for bulk ferroel…
The paper comments on a paper by Dawber and Scott published in Appl. Phys. Lett, 76,1060 (2000) and addendum (ibid. p.3655), which addresses an important issue of the physics of ferroelectric thin films - the role of oxygen vacancies in polarization fatigue. It is shown that the content of this paper (starting equations, calculations, parameters used in calculations and the way the obtained results are compared to the experimental data available in the literature) enables questioning the results and conclusions reported in it.
The momentum-dependent Rashba and Dresselhaus spin-splitting has gained much attention for its highly promising applications in spintronics. In the present work, ab initio density functional theory calculations are performed to study the spin-splitting effect in ferroelectric oxide perovskite KIO3. Our calculations are additionally supported by symmetry adapted two-band k.p Hamiltonian. Non-negligible spin-splitting effect is observed at conduction band minimum (CBm) and valence band maximum (VBM) for rhombohedral R3m and R3c phases. Linear Rashba terms successfully explain the splitting at VB…
The incompatibility of partial d occupation on the perovskite B-site with the standard charge transfer mechanism for ferroelectricity has been a central paradigm in multiferroics research. Nevertheless, it was recently shown by density functional theory calculations that CaMnO_3 exhibits a polar instability that even dominates over the octahedral tilting for slightly enlarged unit cell volume. Here, we present similar calculations for LaCrO_3, which has the same d^3 B-site electron configuration as CaMnO_3. We find that LaCrO_3 exhibits a very similar, albeit much weaker, polar instability as …
Sc-based III-nitride alloys were studied using Density Functional Theory with special quasi-random structures and were found to retain wide band gaps which stay direct up to x = 0.125 (ScxAl1-xN) and x = 0.375 (ScxGa1-xN). Epitaxial strain stabilization prevents spinodal decomposition up to x = 0.3 (ScxAl1-xN on GaN) and x = 0.24 (ScxGa1-xN on GaN), with critical thicknesses for strain relaxation ranging from 3 nm to near-infinity. The increase in Sc content introduces compressive in-plane stress with respect to AlN and GaN, and leads to composition- and stress-tunable band gaps and polarizati…
This is a reply to cond-mat/0211660 by A.K. Taganstev, which consists of a set of criticisms of our publications on polarisation fatigue in Applied Physics Letters. Although his comments were rejected by Applied Physics Letters more than two years ago, Dr Tagantsev has published them in this archive on 29/11/2002. We reply to each of his criticisms here.
Results from dielectric and structural measurements on epitaxial SrTiO$_3$/BaZrO$_3$ superlattices reveal properties that cannot be explained simply in terms of those measured on single films of the constituent materials. For large superlattice periodicities (20/20 and 38/38 structures, i.e. samples in which each SrTiO3 and BaZrO3 layer are 20 or 38 unit cells thick, respectively), the capacitance-voltage curves indicate room-temperature ferroelectricity. For smaller periodicities (7/7 and 15/15), anti-ferroelectric-type behavior is observed, suggesting strong coupling between individual polar…
We review results obtained from recent neutron scattering studies of the lead-oxide class of perovskite relaxors PMN and PZN. A ferroelectric soft mode has been identified in PMN at 1100 K that becomes overdamped near 620 K. This is the same temperature at which polar nanoregions (PNR) begin to form, denoted by Td, and suggests that a direct connection exists between the soft mode and the PNR. The appearance of diffuse scattering intensity at Td reported by Naberezhnov et al. lends further support to this picture. At lower temperature the soft mode in PMN reappears close to Tc = 213 K (defined…
An ab initio structure optimization technique is newly developed to determine the valley line on a total-energy surface for zone-center distortions of ferroelectric perovskite oxides and is applied to barium titanate BaTiO3 and lead titanate PbTiO3. The proposed technique is an improvement over King-Smith and Vanderbilt's scheme [Phys. Rev. B 49, p.5828 (1994)] of evaluating total energy as a function of the amplitude of atomic displacements. The results of numerical calculations show that total energy can be expressed as a fourth-order function of the amplitude of atomic displacements in BaTi…
Ferroelectricity enables key integrated technologies from non-volatile memory to precision ultrasound. Wurtzite ferroelectric Al1-xScxN has recently attracted attention because of its robust ferroelectricity and Si process compatibility in addition to being the first known ferroelectric wurtzite. However, the origin and control of ferroelectricity in wurtzite materials is not yet fully understood. Here we show that the local bond ionicity, rather than simply the change in tetrahedral distortion, is key to controlling the macroscopic ferroelectric response, according to our coupled experimental…
PbTiO3 has the highest tetragonal distortion (c/a=1.064) and highest spontaneous polarization among perovskite titanates. But, it is hazardous and hence one needs to reduce Pb content by substituting or reducing Pb content for use in applications. Pb(1-x)(K0.5Sm0.5)xTiO3 (0&x&0.5) perovskite powders were synthesized by sol-gel process, where Pb2+ was replaced by a combination of K+10.5Sm+30.5 (equivalent charge and comparable ionic radius) providing an excellent substitution model to study changes in structural and electrical properties. Vibrational properties and dielectric properties are mod…
Ternary cubic perovskite compounds of the form A_(1/3)A'_(1/3)A''_(1/3)BO_3 and AB_(1/3)B'_(1/3)B''_(1/3)O_3, in which the differentiated cations form an alternating series of monolayers, are studied using first-principles methods. Such compounds are representative of a possible new class of materials in which ferroelectricity is perturbed by compositional breaking of inversion symmetry. For isovalent substitution on either sublattice, the ferroelectric double-well potential is found to persist, but becomes sufficiently asymmetric that minority domains may no longer survive. The strength of th…
The Perdew-Burke-Ernzerhof generalized gradient approximation to the density functional theory is tested with respect to sensitivity to the choice of the value of the parameter $κ$, which is associated to the degree of localization of the exchange-correlation hole. A study of structural and dynamical properties of four selected ferroelectric perovskites is presented. The originally proposed value of $κ$=0.804 %(best suited for atoms and molecules) works well for some solids, whereas for the ABO$_3$ perovskites it must be decreased in order to predict equilibrium lattice parameters in good agre…
Two-dimensional (2D) hybrid organic-inorganic perovskites (HOIPs) are introducing new directions in the 2D materials landscape. The coexistence of ferroelectricity and spin-orbit interactions play a key role in their optoelectronic properties. We perform a detailed study on a recently synthesized ferroelectric 2D-HOIP, (AMP)PbI$_4$ (AMP = 4-aminomethyl-piperidinium). The calculated polarization and Rashba parameter are in excellent agreement with experimental values. We report a striking new effect, i.e., an extraordinarily large Rashba anisotropy that is tunable by ferroelectric polarization:…
We investigate the crystal structure in multiferroic tetragonal perovskite Sr$_{1/2}$Ba$_{1/2}$MnO$_3$ with high accuracy of the order of 10$^{-3}$ Angstrom for an atomic displacement. The large atomic displacement for Mn ion from the centerosymmetric position, comparable with the off-centering distortion in the tetragonal ferroelectric BaTiO$_3$, is observed in the ferroelectric phase ($T_\mathrm{N}$ $\leq$ $T$ $\leq$ $T_\mathrm{C}$). In stark contrast, in the multiferroic phase ($T$ $\leq$ $T_\mathrm{N}$), the atomic displacement for Mn ion is suppressed, but those for O ions are enlarged. T…
Systematic comparison of approximations and functionals in first-principle calculations of aluminum-based III-V ferroelectric nitrides
University of Arkansas（阿肯色大学）；Guangdong Technion – Israel Institute of Technology（广东以色列理工学院）；Colorado School of Mines（科罗拉多矿业学院）；National Laboratory of the Rockies（落基山国家实验室）；Tel Aviv University（特拉维夫大学）；Université Paris-Saclay（巴黎萨克雷大学）；CentraleSupélec（中央苏佩雷勒高等电信学院）
Design of novel artificial materials based on ferroelectric perovskites relies on the basic principles of electrostatic coupling and in-plane lattice matching. These rules state that the out-of-plane component of the electric displacement field and the in-plane components of the strain are preserved across a layered superlattice, provided that certain growth conditions are respected. Intense research is currently directed at optimizing materials functionalities based on these guidelines, often with remarkable success. Such principles, however, are of limited practical use unless one disposes o…
Bulk chalcogenide perovskite BaZrS3 (BZS), with a direct band gap in visible region, is an important photovoltaic material, albeit with limited applicability owing to its antiferroelectric (AF) nature. Presently, ferroelectric (FE) perovskite-based photovoltaics are attracting enormous attention for environmental stability and better energy conversion efficiency through enhanced charge separation, owing to loss of center of inversion symmetry. We report on antiferroelectric-ferroelectric (AF-FE) phases of BZS thin film, grown with chemical vapor deposition (CVD), using temperature-dependent Ra…
The magnetic order, spin dynamics, and crystal structure of the multiferroic Sr0.56Ba0.44MnO3 have been investigated using neutron and x-ray scattering. Ferroelectricity develops at TC=305 K with a polarization of 4.2 microC/cm2 associated with the displacements of the Mn ions, while the Mn4+ spins order below TN = 200 K into a simple G-type commensurate magnetic structure. Below TN the ferroelectric order decreases dramatically demonstrating that the two order parameters are strongly coupled. The ground state spin dynamics are characterized by a spin gap of 4.6(5) meV and the magnon density o…
The low thermal conductivity of piezoelectric perovskites is a challenge for high power transducer applications. We report first principles calculations of the thermal conductivity of ferroelectric PbTiO$_3$ and the cubic nearly ferroelectric perovskite KTaO$_3$. The calculated thermal conductivity of PbTiO$_3$ is much lower than that of KTaO$_3$ in accord with experiment. Analysis of the results shows that the reason for the low thermal conductivity of PbTiO$_3$ is the presence of low frequency optical phonons associated with the polar modes. These are less dispersive in PbTiO$_3$, leading to…
First-principles calculations within the weighted density approximation (WDA) were performed for ground state properties of ferroelectric perovskites PbTiO$_3$, BaTiO$_3$, SrTiO$_3$, KNbO$_3$ and KTaO$_3$. We used the plane-wave pseudopotential method, a pair distribution function $G$ based on the uniform electron gas, and shell partitioning. Comparing with the local density approximation (LDA) and the general gradient approximation (GGA), we found that the WDA significantly improves the equilibrium volume of these materials in cubic symmetry over both the LDA and GGA; Ferroelectric instabilit…
Recently, the perovskite BiCoO$_3$ has been shown experimentally to be isostructural with PbTiO$_3$, while simultaneously the $d^6$ Co$^{3+}$ ion has a high spin ground state with $C$-type antiferromagnetic ordering. Using hybrid density functional calculations, we investigate the atomic, electronic and magnetic structure of BiCoO$_3$ to elucidate the origin of the multiferroic state. To begin with, we perform a qualitative trend sudy of the role of $d$ electrons in affecting the tendency for perovskite materials to exhibit a ferroelectric distortion; this work initially explores a qualitative…
Advances in first-principles computational approaches have, over the past fifteen years, made possible the investigation of physical properties of ferroelectric systems. In particular, such approaches have led to a microscopic understanding of the occurrence of ferroelectricity in perovskite oxides at ambient pressure. In this paper, we report ab-initio studies on the effect of hydrostatic pressure on the ferroelectricity in perovskites and related materials. We found that, unlike commonly believed, these materials exhibit ferroelectricity at high enough pressure. We also explained in details …
