The spatio-temporal dynamics of separation bubbles induced to form in a fully-developed turbulent boundary layer (with Reynolds number based on momentum thickness of the boundary layer of 490) over a flat plate are studied via direct numerical simulations. Two different separation bubbles are examined: one induced by a suction-blowing velocity profile on the top boundary and the other, by a suction-only velocity profile. The latter condition allows reattachment to occur without an externally imposed favourable pressure gradient and leads to a separation bubble more representative of those occurring over airfoils and in diffusers. The suction-only separation bubble exhibits a range of clearly distinguishable modes including a high-frequency mode and a low-frequency "breathing" mode that has been observed in some previous experiments. The high-frequency mode is well characterized by classical frequency scalings for a plane mixing layer and is associated with the formation and shedding of spanwise oriented vortex rollers. The topology associated with the low-frequency motion is revealed by applying dynamic mode decomposition to the data from the simulations and is shown to be dominated by highly elongated structures in the streamwise direction. The possibility of Görtler instability induced by the streamwise curvature on the upstream end of the separation bubble as the underlying mechanism for these structures and the associated low frequency is explored.
This article describes the fluid dynamics video: "Turbulent Bubbly Channel Flow: Role of Bubble Deformability." The effect of bubble deformability on the flow rate of bubbly upflow in a turbulent vertical channel is examined using direct numerical simulations. A series of simulations with bubbles of decreasing deformability shows a transition from flow where deformable bubbles remain in the middle of the channel to a situation where nearly spherical bubbles slide along the walls.
This review focuses on Direct numerical simulations (DNS) of turbulent flows laden with droplets or bubbles. DNS of these flows are more challenging than those of flows laden with solid particles due to the surface deformation in the former. The classification of the discussed numerical methods is based on whether the initial diameter of the bubble/droplet is smaller or larger than the Kolmogorov length scale, and whether the instantaneous surface deformation is fully resolved or obtained via a phenomenological model. Numerical methods that account for the breakup of single droplet/bubble as w…
We investigate the modes of deformation of an initially spherical bubble immersed in a homogeneous and isotropic turbulent background flow. We perform direct numerical simulations of the two-phase incompressible Navier-Stokes equations, considering a low-density bubble in the high density turbulent flow at various Weber number (the ratio of turbulent and surface tension forces) using the air-water density ratio. We discuss a theoretical framework for the bubble deformation in a turbulent flow using a spherical harmonic decomposition. We propose, for each mode of bubble deformation, a forcing t…
In the maritime industry, the injection of air bubbles into the turbulent boundary layer under the ship hull is seen as one of the most promising techniques to reduce the overall fuel consumption. However, the exact mechanism behind bubble drag reduction is unknown. Here we show that bubble drag reduction in turbulent flow dramatically depends on the bubble size. By adding minute concentrations (6 ppm) of the surfactant Triton X-100 into otherwise completely unchanged strongly turbulent Taylor-Couette flow containing bubbles, we dramatically reduce the drag reduction from more than 40% to abou…
We present experiments on large air cavities spanning a wide range of sizes relative to the Hinze scale $d_\mathrm{H}$, the scale at which turbulent stresses are balanced by surface tension, disintegrating in turbulence. For cavities with initial sizes $d_0$ much larger than $d_\mathrm{H}$ (probing up to $d_0 / d_\mathrm{H} = 8.3$), the size distribution of bubbles smaller than $d_\mathrm{H}$ follows $N(d) \propto d^{-3/2}$, with $d$ the bubble diameter. The capillary instability of ligaments involved in the deformation of the large bubbles is shown visually to be responsible for the creation …
The phenomenon of drag reduction induced by injection of bubbles into a turbulent carrier fluid has been known for a long time; the governing control parameters and underlying physics is however not well understood. In this paper, we use three dimensional numerical simulations to uncover the effect of deformability of bubbles injected in a turbulent Taylor-Couette flow on the overall drag experienced by the system. We consider two different Reynolds numbers for the carrier flow, i.e. $Re_i=5\times 10^3$ and $Re_i=2\times 10^4$; the deformability of the bubbles is controlled through the Weber n…
We conduct experiments in a turbulent bubbly flow to study the nature of the transition between the classical $-$5/3 energy spectrum scaling for a single-phase turbulent flow and the $-$3 scaling for a swarm of bubbles rising in a quiescent liquid and of bubble-dominated turbulence. The bubblance parameter, which measures the ratio of the bubble-induced kinetic energy to the kinetic energy induced by the turbulent liquid fluctuations before bubble injection, is often used to characterise the bubbly flow. We vary the bubblance parameter from $b = \infty$ (pseudo-turbulence) to $b = 0$ (single-p…
Data from Direct Numerical Simulations of disperse bubbly flows in a vertical channel are used to study the effect of the bubbles on the carrier-phase turbulence. A new method is developed, based on the barycentric map approach, that allows to quantify the anisotropy and componentiality of the flow at any scale. Using this the bubbles are found to significantly enhance flow anisotropy at all scales compared with the unladen case, and for some bubble cases, very strong anisotropy persists down to the smallest flow scales. The strongest anisotropy observed was for the cases involving small bubbl…
We numerically investigate turbulent Rayleigh-Bénard convection with gas bubbles attached to the hot plate, mimicking a core feature in electrolysis, catalysis, or boiling. The existence of bubbles on the plate reduces the global heat transfer due to the much lower thermal conductivity of gases as compared to liquids and changes the structure of the boundary layers. The numerical simulations are performed in 3D at Prandtl number Pr=4.38 (water) and Rayleigh number $10^7\le Ra \le10^8$. For simplicity, we assume the bubbles to be equally-sized and having pinned contact lines. We vary the total …
Mass-Transfer Control With Microbubbles in Highly Turbulent Decaying Flows
George W. Woodruff School of Mechanical Engineering, Georgia Institute of Technology（乔治·W·伍德拉夫机械工程学院，佐治亚理工学院）；Renewable Bioproducts Institute, Georgia Institute of Technology（可再生生物制品研究所，佐治亚理工学院）
In incompressible and periodic statistically stationary turbulence, exchanges of turbulent energy across scales and space are characterised by very intense and intermittent spatio-temporal fluctuations around zero of the time-derivative term, the spatial turbulent transport of fluctuating energy, and the pressure-velocity term. These fluctuations are correlated with each other and with the intense intermittent fluctuations of the interscale energy transfer rate. These correlations are caused by the sweeping effect, the link between non-linearity and non-locality, and also relate to geometrical…
We use direct numerical simulation (DNS) to explore the effect of tilt on two-dimensional turbulent thermal convection on a half-soap bubble that is heated at its equator.In the DNS, the bubble is tilted by an angle $δ\in[0^{\circ},90^{\circ}]$, the Rayleigh number is varied between $Ra\in[3\times10^6, 3\times10^9]$, and the Prandlt number is fixed at $Pr=7$.The DNS reveals two qualitatively different flow regimes: the dynamic plume regime (DPR) and the stable plume regime (SPR).In the DPR, small dynamic plumes constantly emerge from random locations on the equator and dissipate on the bubble.…
In this paper, we present the results of a numerical study of air-water turbulent bubbly flow in a periodic vertical square duct. The study is conducted using a novel numerical technique which leverages Volume of Fluid method for interface capturing and Sharp Surface Force method for accurate representation of the surface tension forces. A three-dimensional geometry construction method is employed during solution of interface equation which gives absolute conservation of mass and sharp interface between gas and liquid phases. The entire algorithm has been implemented on a data parallel mode on…
We report on the Lagrangian statistics of acceleration of small (sub-Kolmogorov) bubbles and tracer particles with Stokes number St << 1 in turbulent flow. At decreasing Reynolds number, the bubble accelerations show deviations from that of tracer particles, i.e. they deviate from the Heisenberg-Yaglom prediction and show a quicker decorrelation despite their small size and minute St. Using direct numerical simulations, we show that these effects arise due the drift of these particles through the turbulent flow. We theoretically predict this gravity-driven effect for developed isotropic turbul…
Breaking waves entrain gas beneath the surface. The wave-breaking process energizes turbulent fluctuations that break bubbles in quick succession to generate a wide range of bubble sizes. Understanding this generation mechanism paves the way towards the development of predictive models for large-scale maritime and climate simulations. Garrett et al. (2000) suggested that super-Hinze-scale turbulent breakup transfers entrained gas from large to small bubble sizes in the manner of a cascade. We provide a theoretical basis for this bubble-mass cascade by appealing to how energy is transferred fro…
This paper present a simulation strategy for DNS of turbulent co-current Taylor bubble flow. This is a continuation of the work presented in [2] in which Large Eddy Simulation (LES) of co-current turbulent Taylor bubble flow was presented. It was observed that one of the main challenges is the physically accurate prediction of the behavior of the Taylor bubble skirt, and the related bubble shedding. An underestimation of the turbulent fluctuations in the wake of the Taylor bubble was observed in the LES results. It was suggested that this is related to over-prediction of the loss of void of th…
Identification and extraction of vortical structures and of waves in a disorganised flow is a mayor challenge in the study of turbulence. We present a study of the spatio-temporal behavior of turbulent flows in the presence of different restitutive forces. We show how to compute and analyse the spatio-temporal spectrum from data stemming from numerical simulations and from laboratory experiments. Four cases are considered: homogeneous and isotropic turbulence, rotating turbulence, stratified turbulence, and water wave turbulence. For homogeneous and isotropic turbulence, the spectrum allows id…
Drag reduction by microbubbles is a promising engineering method for improving ship performance. A fundamental theory of the phenomenon is lacking however, making actual design quite uphazard. We offer here a theory of drag reduction by microbubbles in the limit of very small bubbles, when the effect of the bubbles is mainly to normalize the density and the viscosity of the carrier fluid. The theory culminates with a prediction of the degree of drag reduction given the concentration profile of the bubbles. Comparisons with experiments are discussed and the road ahead is sketched.
An extension of Proper Orthogonal Decomposition is applied to the wall layer of a turbulent channel flow (Re τ = 590), so that empirical eigenfunctions are defined in both space and time. Due to the statistical symmetries of the flow, the igenfunctions are associated with individual wavenumbers and frequencies. Self-similarity of the dominant eigenfunctions, consistent with wall-attached structures transferring energy into the core region, is established. The most energetic modes are characterized by a fundamental time scale in the range 200-300 viscous wall units. The full spatio-temporal dec…
We present data driven kinematic models for the motion of bubbles in high-Re turbulent fluid flows based on recurrent neural networks with long-short term memory enhancements. The models extend empirical relations, such as Maxey-Riley (MR) and its variants, whose applicability is limited when either the bubble size is large or the flow is very complex. The recurrent neural networks are trained on the trajectories of bubbles obtained by Direct Numerical Simulations (DNS) of the Navier Stokes equations for a two-component incompressible flow model. Long short term memory components exploit the t…
Streaming Dynamic Mode Decomposition (sDMD) (Hemati et al., Phys. Fluids 26(2014)) is a low-storage version of Dynamic Mode Decomposition (DMD) (Schmid, J. Fluid Mech. 656 (2010)), a data-driven method to extract spatio-temporal flow patterns. Streaming DMD avoids storing the entire data sequence in memory by approximating the dynamic modes through incremental updates with new available data. In this paper, we use sDMD to identify and extract dominant spatio-temporal structures of different turbulent flows, requiring the analysis of large datasets. First, the efficiency and accuracy of sDMD ar…
Interface-resolved direct numerical simulations are performed to examine the combined effects of soluble surfactant and viscoelasticity on the structure of a bubbly turbulent channel flow. The incompressible flow equations are solved fully coupled with the FENE-P viscoelastic model and the equations governing interfacial and bulk surfactant concentrations. The latter coupling is achieved through a non-linear equation of state which relates the surface tension to the surfactant concentration at the interface. The two-fluid Navier-Stokes equations are solved using a front-tracking method, augmen…
Bubbly turbulent Taylor-Couette (TC) flow is globally and locally studied at Reynolds numbers of Re = 5 x 10^5 to 2 x 10^6 with a stationary outer cylinder and a mean bubble diameter around 1 mm. We measure the drag reduction (DR) based on the global dimensional torque as a function of the global gas volume fraction a_global over the range 0% to 4%. We observe a moderate DR of up to 7% for Re = 5.1 x 10^5. Significantly stronger DR is achieved for Re = 1.0 x 10^6 and 2.0 x 10^6 with, remarkably, more than 40% of DR at Re = 2.0 x 10^6 and a_global = 4%. To shed light on the two apparently diffe…
A new turbulent Taylor-Couette system consisting of two independently rotating cylinders has been constructed. The gap between the cylinders has a height of 0.927 m, an inner radius of 0.200 m, and a variable outer radius (from 0.279 to 0.220 m). The maximum angular rotation rates of the inner and outer cylinder are 20 and 10 Hz, respectively, resulting in Reynolds numbers up to 3.4 x 10^6 with water as working fluid. With this Taylor-Couette system, the parameter space (Re_i, Re_o, η) extends to (2.0 x 10^6, {\pm}1.4 x 10^6, 0.716-0.909). The system is equipped with bubble injectors, temperat…
Using the Taylor--Couette geometry we experimentally investigate the effect of salt on drag reduction caused by bubbles present in the flow. We combine torque measurements with optical high-speed imaging to relate the bubble size to the drag experienced by the flow. Previous findings have shown that a small percentage of air (4%) can lead to dramatic drag reduction (40%). In contrast to previous laboratory experiments, which mainly used fresh water, we will vary the salinity from fresh water to the average salinity of ocean water. We find that the drag reduction is increasingly more inhibited …
The properties of bubble-laden turbulent flows at different scales are investigated experimentally, focusing on the flow kinetic energy, energy transfer, and extreme events. The experiments employed particle shadow velocimetry measurements to measure the flow in a column generated by a homogeneous bubble swarm rising in water, for two different bubble diameters ($2.7$ mm $\&$ $3.9$ mm) and moderate gas volume fractions ($0.26\%\sim1.31\%$). The two velocity components were measured at high-resolution, and used to construct structure functions up to twelfth order for separations spanning the sm…
The spatio-temporal statistical structure of the turbulent dissipation field and its stochastic representation as a Gaussian Multiplicative Chaos
Univ Lyon, Ens de Lyon, Univ Claude Bernard, CNRS, Laboratoire de Physique（里昂大学，巴黎高等师范学院里昂分校，克洛德·贝尔纳大学，法国国家科学研究中心，物理实验室）；CNRS, ICJ UMR5208, Ecole Centrale de Lyon, INSA Lyon, Université Claude Bernard Lyon 1, Université Jean Monnet（法国国家科学研究中心，里昂中央理工学院，里昂国立应用科学学院，里昂克洛德·贝尔纳大学，让·莫内大学）
Turbulent flow separation induced by a protuberance on one of the walls of an otherwise planar channel is investigated using Direct Numerical Simulations. Different bulge geometries and Reynolds numbers - with the highest friction Reynolds number simulation reaching a peak of Reτ = 900 - are addressed to understand the effect of the wall curvature and of the Reynolds number on the dynamics of the recirculating bubble behind the bump. Most of the drag is due to the form contribution, whilst the friction contribution does not change appreciably with respect to an equivalent planar channel flow. …
We create a highly controlled lab environment-accessible to both global and local monitoring-to analyse turbulent boiling flows and in particular their shear stress in a statistically stationary state. Namely, by precisely monitoring the drag of strongly turbulent Taylor-Couette flow (the flow in between two co-axially rotating cylinders, Reynolds number $\textrm{Re}\approx 10^6$) during its transition from non-boiling to boiling, we show that the intuitive expectation, namely that a few volume percent of vapor bubbles would correspondingly change the global drag by a few percent, is wrong. Ra…
We report on the modification of the spectrum of a passive scalar inside a turbulent flow by the injection of large bubbles. While the spectral modification through bubbles is well known and well analyzed for the velocity fluctuations, little is known on how bubbles change the fluctuations of an approximately passive scalar, in our case temperature. Here we uncover the thermal spectral scaling behavior of a turbulent multiphase thermal mixing layer. The development of a $-3$ spectral scaling is triggered. By injecting large bubbles ($\text{Re}_{\text{bub}} = \mathcal{O}(10^2)$) with gas volume…
Polymer additives are commonly utilized to manipulate bubbly flows in various applications. Here, we investigate the effects of clean and contaminated bubbles driven upwards (upflow) in Newtonian and viscoelastic turbulent channel flows. Interface-resolved direct numerical simulations are performed to examine sole and combined effects of soluble surfactant and viscoelasticity using an efficient 3D finite-difference/front-tracking method. The incompressible flow equations are solved fully coupled with the FENE-P viscoelastic model and the equations governing interfacial and bulk surfactant conc…
Numerical simulations of a model of plane Couette flow focusing on its in-plane spatio-temporal properties are used to study the dynamics of turbulent spots.
Breaking waves generate a distribution of bubble sizes that evolves over time. Knowledge of how this distribution evolves is of practical importance for maritime and climate studies. The analytical framework developed in Part 1 examined how this evolution is governed by the bubble-mass flux from large to small bubble sizes, which depends on the rate of break-up events and the distribution of child bubble sizes. These statistics are measured in Part 2 as ensemble-averaged functions of time by simulating ensembles of breaking waves, and identifying and tracking individual bubbles and their break…
We conduct numerical experiments to investigate the spatial clustering of particles and bubbles in simulations of homogeneous and isotropic turbulence. Varying the Stokes parameter and the densities, striking differences in the clustering of the particles can be observed. To quantify these visual findings we use the Kaplan--Yorke dimension. This local scaling analysis shows a dimension of approximately 1.4 for the light bubble distribution, whereas the distribution of very heavy particles shows a dimension of approximately 2.4. However, clearly separate parameter combinations yield the same di…
This work describes an experimental investigation on the mixing induced by a swarm of high Reynolds number air bubbles rising through a nearly homogeneous and isotropic turbulent flow. The gas volume fraction $α$ and the velocity fluctuations $u'_0$ of the carrier flow before bubble injection are varied, respectively, in the ranges $0\leq α\leq 0.93\%$ and 2.3 cm/s $\leq u'_0 \leq 5.5$ cm/s, resulting in a variation of the bubblance parameter $b$ in the range [0, 1.3] ($b = \frac{V_r^2 α}{{u'}_0^2}$, where $V_r$ is the relative rising velocity). Mixing in the horizontal direction can be modell…
Single-point hot-wire measurements in the bulk of a turbulent channel have been performed in order to detect and quantify the phenomenon of preferential bubble accumulation. We show that statistical analysis of the bubble-probe colliding-times series can give a robust method for investigation of clustering in the bulk regions of a turbulent flow where, due to the opacity of the flow, no imaging technique can be employed. We demonstrate that micro-bubbles (radius R_0 ~ 0.1 mm) in a developed turbulent flow, where the Kolmogorov length-scale is, eta ~ R_0, display preferential concentration in s…
We develop a passive control strategy for suppressing thermoacoustic instability in a bluff-body stabilized premixed turbulent combustor. When the equivalence ratio is varied, there is a transition from combustion noise to thermoacoustic instability via intermittency in the combustor. We perform simultaneous acoustic pressure, 2D-PIV, and CH$^*$ chemiluminescence measurements to capture the pressure fluctuations, the velocity field, and the heat release rate (HRR) field during the transition. We measure the spatial distribution of the amplitude of turbulent velocity at the acoustic frequency, …
Fluid turbulence is commonly associated with stronger drag, greater heat transfer, and more efficient mixing than in laminar flows. In many natural and industrial settings, turbulent liquid flows contain suspensions of dispersed bubbles and light particles. Recently, much attention has been devoted to understanding the behavior and underlying physics of such flows by use of both experiments and high-resolution direct numerical simulations. This review summarizes our present understanding of various phenomenological aspects of bubbly and buoyant particle-laden turbulent flows. We begin by discu…
Starting with turbulence that explores a wide region in phase space, we discover several relative periodic orbits (RPOs) embedded within a subregion of the chaotic turbulent saddle. We also extract directly from simulation, several travelling waves (TWs). These TWs together with the RPOs are unstable states and are believed to provide the skeleton of the chaotic saddle. Earlier studies have shown that such invariant solutions can help to explain wall bounded shear flows, and a finite subset of them are expected to dominate the dynamics (Faisst & Eckhardt 2003; Pringle & Kerswell 2007; Hof et a…
