The Cherenkov Telescope Array (CTA) is a future ground-based gamma-ray observatory that will provide unprecedented sensitivity and angular resolution for the detection of gamma rays with energies above a few tens of GeV. In comparison to existing instruments (like H.E.S.S., MAGIC, and VERITAS) the sensitivity will be improved by installing two extended arrays of telescopes in the northern and southern hemisphere, respectively. A large number of planned telescopes (>100 in total) motivates the application of predictive maintenance techniques to the individual telescopes. A constant and automatic condition monitoring of the mechanical telescope structure and of the drive system (motors, gears) is considered for this purpose. The condition monitoring system aims at detecting degradations well before critical errors occur; it should help to ensure long-term operation and to reduce the maintenance efforts of the observatory. We present approaches for the condition monitoring of the structure and the drive system of Medium-Sized Telescopes (MSTs), respectively. The overall concept has been developed and tested at the MST prototype for CTA in Berlin. The sensors used, the joint data acquisition system, possible analysis methods (like Operational Modal Analysis, OMA, and Experimental Modal Analysis, EMA) and first performance results are discussed.
The Cherenkov Telescope Array (CTA) is the next ground-based $γ$-ray observatory in the TeV $γ$-ray spectral region operating with the Imaging Atmospheric Cherenkov Technique. It is based on almost 70 telescopes of different class diameters - LST, MST and SST of 23, 12, and 4 m, respectively - to be installed in two sites in the two hemispheres (at La Palma, Canary Islands, and near Paranal, Chile). Several thousands of reflecting mirror tiles larger than 1 m$^2$ will be produced for realizing the segmented primary mirrors of a so large number of telescopes. Almost in parallel, the ASTRI Mini-…
The next generation instrument for ground-based gamma-ray astronomy will be the Cherenkov Telescope Array (CTA), consisting of approximately 100 telescopes in three sizes, built on two sites with one each in the Northern and Southern Hemi- spheres. Up to 40 of these will be Medium Size Telescopes (MSTs) which will dominate sensitivity in the core energy range. Since 2012, a full size mechanical prototype for the modified 12 m Davies-Cotton design MST has been in operation in Berlin. This doc- ument describes the techniques which have been implemented to calibrate and optimise the mechanical an…
The Cherenkov Telescope Array (CTA) is the planned next-generation instrument for ground-based gamma-ray astronomy, covering a photon energy range of ~20 GeV to above 100 TeV. CTA will consist of the order of 100 telescopes of three sizes, installed at two sites in the Northern and Southern Hemisphere. This contribution deals with the 12 meter Medium Size Telescopes (MST) having a single mirror (modified Davies-Cotton, DC) design. In the baseline design of the CTA arrays, 25 MSTs in the South and 15 MSTs in the North provide the necessary sensitivity for CTA in the core energy range of 100 GeV…
The Cherenkov Telescope Array (CTA), is an international project for the next generation ground- based observatory for gamma-ray astronomy in the energy range from 20 GeV to 300 TeV. The sensitivity in the core energy range will be dominated by up to 40 Medium-Sized Telescopes (MSTs). The MSTs, of Davies-Cotton type with a 12 m diameter reflector are currently in the prototype phase. A full-size mechanical telescope structure has been assembled in Berlin. The telescope is partially equipped with different mirror prototypes, which are currently being tested and evaluated for performances charac…
The Cherenkov Telescope Array (CTA) is the next generation of ground-based gamma-ray observatory. The observatory will consist of two arrays, one located in the southern hemisphere (Paranal,Chile) and the other in the northern hemisphere (Canary Island, Spain), covering the whole sky in the range of observation. More than 100 telescopes are planned to be in operation for as long as 30 years, which motivated the development of a continuous condition monitoring of the individual telescopes. The main goal of the monitoring is to detect degradation and failures before critical damages occur. Two a…
The Cherenkov Telescope Array (CTA) will be the future observatory for TeV gamma-ray astronomy. In order to increase the sensitivity and to extend the energy coverage beyond the capabilities of current facilities, its design concept features telescopes of three different size classes. Based on the experience from H.E.S.S. phase II, the Institute for Astronomy and Astrophysics Tübingen (IAAT) develops actuators for the mirror control system of the CTA Medium Size Telescopes (MSTs). The goals of this effort are durability, high precision, and mechanical stability under all environmental conditio…
The pointing capability of a telescope in the Cherenkov Telescope Array (CTA) is a crucial aspect in the calibration of the instrument. It describes how a position in the sky is transformed to the focal plane of the telescope and allows precise directional reconstructions of atmospheric particle showers. The favoured approach for pointing calibrations of the Medium Size Telescopes (MST) is the utilisation of an CCD-camera installed in the centre of the dish, which images the night sky and the focal plane simultaneously. The technical implementation of this solution and test results taken over …
As TeV gamma-ray astronomy progresses into the era of the Cherenkov Telescope Array (CTA), there is a desire for the capacity to instantaneously follow up on transient phenomena and continuously monitor gamma-ray flux at energies above $10^{12}$ eV. To this end, a worldwide network of Imaging Air Cherenkov Telescopes (IACTs) is required to provide triggers for CTA observations and complementary continuous monitoring. An IACT array sited in Australia would contribute significant coverage of the Southern Hemisphere sky. Here, we investigate the suitability of a small IACT array and how different…
The Cherenkov Telescope Array (CTA) is a future very high energy gamma-ray observatory. CTA will be comprised of small-, medium- and large-size telescopes covering an energy range from tens of GeV to hundreds of TeV and will surpass existing telescopes in sensitivity by an order of magnitude. The aim of our study is to find the optimal design for the medium-size telescopes (MSTs), which will determine the sensitivity in the key energy range between a few hundred GeV to about ten TeV. To study the effect of the telescope design parameters on the array performance, we simulated arrays of 61 MSTs…
Pointing calibration is an offline correction applied in order to obtain the true pointing direction of a telescope. The Cherenkov Telescope Array (CTA) aims to have the precision to determine the position of point-like as well as slightly extended sources, with the goal of systematic errors less than 7 arc seconds in space angle. This poster describes the pointing calibration concept being developed for the CTA Medium Size Telescope (MST) prototype at Berlin-Adlershof, showing test results and preliminary measurements. The MST pointing calibration method uses two CCD cameras, mounted on the t…
The Cherenkov Telescope Array (CTA) is a ground-based $γ$-ray observatory that will observe the full sky in the energy range from 20 GeV to 100 TeV from facilities in both hemispheres. It is proposed to consist of more than 100 telescopes, producing large amounts of data. Apart from the storage system, there are also requirements on the software framework to allow efficient data processing, i.e. robustness, execution speed and coding efficiency. This contribution will present a plain and simple pipeline framework design prototype for CTA that builds upon well-known tools, allowing the users to…
The Gamma-ray Cherenkov Telescope (GCT) is an innovative dual-mirror solution proposed for the Small Size Telescopes of the future Cherenkov Telescope Array (CTA), capable of imaging the showers induced by cosmic gamma-rays with energies from a few TeV up to 300 TeV. The Schwarzschild Couder design on which the telescope optical design is based makes possible the construction of a fast telescope (primary mirror diameter 4 m, focal length 2.3 m) with a plate scale well matched to compact photosensors, such as multi anode or silicon photomultipliers (MAPMs and SiPMs, respectively) for the camera…
The Cherenkov Telescope Array (CTA) is a ground-based $γ$-ray observatory that will observe the full sky in the energy range from 20 GeV to 100 TeV from facilities in both hemispheres. It is proposed to consist of more than 100 telescopes and the large amount of data produced will exceed the volume of current VHE Imaging Atmospheric Cherenkov Telescopes by $\sim$two orders of magnitude. This volume of data represents a new challenge to the community, which is looking for new data formats to transfer and store the CTA data. One of the prototypes currently under study is the ROI (Regions Of Inte…
The Cherenkov Telescope Array (CTA) is a future very high energy gamma-ray observatory. CTA will be comprised of small-,medium- and large-size telescopes covering an energy range from tens of GeV to hundreds of TeV and will surpass existing telescopes in sensitivity by an order of magnitude. The aim of our study is to find the optimal design for the medium-size telescopes (MSTs), which will determine the sensitivity in the key energy range between a few hundred GeV to about ten TeV. To study the effect of the telescope design parameters on the array performance, we simulated arrays of 61 MSTs …
NectarCAM is a camera developed to detect Cherenkov light between 80 GeV and 30 TeV. It will equip the medium-sized telescopes (MST) of the Cherenkov Telescope Array Observatory (CTAO). The camera comprises 265 modules, covering a field of view of 8 degrees. Each module consists of 7 photomultiplier Tubes (PMTs) equipped with light guides and a front-end board performing the data capture. NectarCAM is based on the NECTAr chip, which combines a switch capacitor array sampling at 1GHz and a 12-bit Analog to Digital Converter (ADC). The NectarCAM camera is currently under integration in CEA Paris…
The pointing system of the prototype of the Large Size Telescope (LST-1) for the Cherenkov Telescope Array observatory, should ensure mapping of the gamma-ray image of a point-like source in the Cherenkov camera to the sky coordinates with a precision better than 14 arcseconds. Detailed studies of the telescope deformations are performed in order to disentangle different deformations and quantify their contributions to the miss-pointing, to learn how to correct for them, and finally how to design the system for offline and online pointing corrections. The LST-1 pointing precision system consis…
The Cherenkov Telescope Array (CTA) is the next-generation gamma-ray observatory currently under construction. It will improve over the current generation of imaging atmospheric Cherenkov telescopes (IACTs) by a factor of five to ten in sensitivity and it will be able to observe the whole sky from a combination of two sites: a northern site in La Palma, Spain, and a southern one in Paranal, Chile. CTA will also be the first open gamma-ray observatory. Accordingly, the data analysis pipeline is developed as open-source software. The event reconstruction pipeline accepts raw data of the telescop…
We present studies for optimizing the next generation of ground-based imaging atmospheric Cherenkov telescopes (IACTs). Results focus on mid-sized telescopes (MSTs) for CTA, detecting very high energy gamma rays in the energy range from a few hundred GeV to a few tens of TeV. We describe a novel, flexible detector Monte Carlo package, FAST (FAst Simulation for imaging air cherenkov Telescopes), that we use to simulate different array and telescope designs. The simulation is somewhat simplified to allow for efficient exploration over a large telescope design parameter space. We investigate a wi…
The Cherenkov Telescope Array (CTA) is an international project for a next-generation ground-based gamma ray observatory, aiming to improve on the sensitivity of current-generation experiments by an order of magnitude and provide energy coverage from 30 GeV to more than 300 TeV. The 9.7m Schwarzschild-Couder (SC) candidate medium-size telescope for CTA exploits a novel aplanatic two-mirror optical design that provides a large field of view of 8 degrees and substantially improves the off-axis performance giving better angular resolution across all of the field of view with respect to single-mir…
In the framework of the Cherenkov Telescope Array (CTA), the GCT (Gamma-ray Cherenkov Telescope) team is building a dual-mirror telescope as one of the proposed prototypes for the CTA small size class of telescopes. The telescope is based on a Schwarzschild- Couder (SC) optical design, an innovative solution for ground-based Cherenkov astronomy, which allows a compact telescope structure, a lightweight large Field of View (FoV) camera and enables good angular resolution across the entire FoV. We review the different mechanical and optical components of the telescope. In order to characterise t…
The observation of energetic astronomical sources emitting very high-energy gamma-rays in the TeV spectral range (as e.g. supernova remnants or blazars) is mainly based on detecting the Cherenkov light induced by relativistic particles in the showers produced by the photon interaction with the Earth atmosphere. The ASTRI Mini-Array is an INAF-led project aimed observing such celestial objects in the 1 - 100 TeV energy range. It consists of an array of nine innovative imaging atmospheric Cherenkov telescopes that are an evolution of the dual-mirror aplanatic ASTRI-Horn telescope operating at th…
Imaging Atmospheric Cherenkov Telescopes (IACTs) are ground-based instruments devoted to the study of very high energy gamma-rays coming from space. The detection technique consists of observing images created by the Cherenkov light emitted when gamma rays, or more generally cosmic rays, propagate through the atmosphere. While in the case of protons or gamma-rays the images present a filled and more or less elongated shape, energetic muons penetrating the atmosphere are visualised as characteristic circular rings or arcs. A relatively simple analysis of the ring images allows the reconstructio…
The Cherenkov Telescope Array (CTA) is the future instrument in ground-based gamma-ray astronomy in the energy range from 20 GeV to 300 TeV. Its sensitivity will surpass that of current generation experiments by a factor $\sim$10, facilitated by telescopes of three sizes. The performance in the core energy regime will be dominated by Medium Size Telescopes (MST) with a reflector of 12 m diameter. A full-size mechanical prototype of the telescope structure has been constructed in Berlin. The performance of the prototype is being evaluated and optimisations, among others, facilitating the assemb…
The Yakutsk array group is developing a wide field-of-view Cherenkov telescope to be operated in coincidence with the surface detectors of the extensive air shower array. Currently, the engineering prototype of the reflecting telescope with the front-end electronics is designed, assembled, and tested to demonstrate the feasibility of the conceived instrument. The status and specifications of the prototype telescope are presented, as well as the modernization program of the already existing Cherenkov light detectors subset of the array measuring ultra-high energy cosmic rays.
The Schwarzschild-Couder Telescope (SCT) is a candidate technology for a medium-sized telescope within the Cherenkov Telescope Array, the next generation ground based observatory for very high energy gamma ray astronomy. The SCT uses a novel two-mirror design and is expected to yield improvements in field of view and image resolution compared to traditional Cherenkov telescopes based on single-mirror-dish optics. To match the improved optical resolution, challenging requirements of high channel count and density at low power consumption must be overcome by the camera. The prototype camera, cur…
A wide field of view Cherenkov/fluorescence telescope array is one of the main components of the Large High Altitude Air Shower Observatory project. To serve as Cherenkov and fluorescence detectors, a flexible and mobile design is adopted for easy reconfiguring of the telescope array. Two prototype telescopes have been constructed and successfully run at the site of the ARGO-YBJ experiment in Tibet. The features and performance of the telescopes are presented.
The Compact High Energy Camera (CHEC) is a camera-development project involving UK, US, Japanese and Dutch institutes for the dual-mirror Small-Sized Telescopes (SST-2M) of the Cherenkov Telescope Array (CTA). Two CHEC prototypes, based on different photosensors are funded and will be assembled and tested in the UK over the next ~18 months. CHEC is designed to record flashes of Cherenkov light lasting from a few to a hundred nanoseconds, with typical RMS image width and length of ~0.2 x 1.0 degrees, and has a 9 degree field of view. The physical camera geometry is dictated by the telescope opt…
The Cherenkov Telescope Array (CTA) is the next generation gamma-ray observatory. CTA will incorporate about 100 imaging atmospheric Cherenkov telescopes (IACTs) at a southern site, and about 20 in the north. Previous IACT experiments have used up to five telescopes. Subsequently, the design of a graphical user interface (GUI) for the operator of CTA poses an interesting challenge. In order to create an effective interface, the CTA team is collaborating with experts from the field of Human-Computer Interaction. We present here our GUI prototype. The back-end of the prototype is a Python Web se…
The SST-1M is a 4-m Davies--Cotton atmospheric Cherenkov telescope optimized to provide gamma-ray sensitivity above a few TeV. The SST-1M is proposed as part of the Small-Size Telescope array for the Cherenkov Telescope Array (CTA), the first prototype has already been deployed. The SST-1M control software of all subsystems (active mirror control, drive system, safety system, photo-detection plane, DigiCam, CCD cameras) and the whole telescope itself (master controller) uses the standard software design proposed for all CTA telescopes based on the ALMA Common Software (ACS) developed to contro…
The FlashCam group is currently preparing photomultiplier-tube based cameras proposed for the medium-sized telescopes (MST) of the Cherenkov Telescope Array (CTA). The cameras are designed around the FlashCam readout concept which is the first fully-digital readout system for Cherenkov cameras, based on commercial FADCs and FPGAs as key components for the front-end electronics modules and a high performance camera server as back-end. This contribution describes the progress of the full-scale FlashCam camera prototype currently under construction, as well as performance results also obtained wi…
The first Large-Sized Telescope (LST-1) proposed for the forthcoming Cherenkov Telescope Array (CTA) has started to operate in 2019 in La Palma. The large structure of LST-1 - with a 23 m mirror dish diameter - imposes a strict control of its deformations that could affect the pointing accuracy and its overall performance. According to CTA specifications that are conceived to resolve e.g. the fine structure of galactic sources, the LST post-calibration pointing accuracy should be better than 14 arcseconds. To fulfill this requirement, the telescope pointing precision is monitored with two dedi…
The atmospheric monitoring devices for the planned calibration system of the Cherenkov Telescope Array (CTA) are undergoing intensive development, prototyping and testing. The All-Sky Cameras, the Sun/Moon Photometers and the FRAM telescopes have been gradually deployed at the future CTA sites with the primary goal of site characterization, simultaneously allowing the assessment of their operational reliability in realistic environmental conditions. All three devices have shown the ability to work smoothly in both the extreme dryness and the large temperature variations of the southern site as…
The Cherenkov Telescope Array is a project that aims to exploring the highest energy region of electromagnetic spectrum. Two arrays, one for each hemisphere, will cover the full sky in a range from few tens of GeV to hundreds of TeV improving the sensitivity and angular resolution of the present operating arrays. A prototype of the Large Size Telescope (LST) for the study of gamma ray astronomy above some tens of GeV will be installed at the Canary Island of La Palma in 2016. The LST camera, made by an array of photomultipliers (PMTs), requires an accurate and systematic calibration over a wid…
The Large-Sized Telescope (LST) prototype of the future Cherenkov Telescope Array (CTA) is located at the Northern site of CTA, on the Canary Island of La Palma. It is designed to provide optimal performance in the lowest part of the energy range covered by CTA, observing gamma rays down to energies of tens of GeV. The LST prototype started performing astronomical observations in November 2019 during the commissioning of the telescope and it has been taking data since then. In this contribution, we will present the tuning of the characteristics of the telescope in the Monte Carlo (MC) simulati…
The Cherenkov Telescope Array will provide unprecedented sensitivity and angular resolution to gamma rays across orders of magnitude in energy. Above 1 TeV up to around 300 TeV an array of Small-Sized Telescopes (SSTs) will cover several kilometres on the ground. The Compact High-Energy Camera (CHEC) is a proposed option for the camera of the SSTs. CHEC contains 2048 pixels of physical size about 6 mm x 6 mm, leading to a field of view of over 8 degrees. Electronics based on custom ASICs (TARGET) and FPGAs sample incoming signals at a gigasample per second and provide a flexible triggering sch…
The Cherenkov Telescopes Array (CTA) is planned to be an Observatory for very high energy gamma ray astronomy and will consist of several tens of telescopes which account for a reflective surface of more than 10000 m$^2$. The mirrors of these telescopes will be formed by a set of facets. Different technological solutions, for a fast and cost efficient production of light-weight mirror facets are under test inside the CTA Consortium. Most of them involve composite structures whose behavior under real observing conditions is not yet fully tested. An outdoor test facility has been built in one of…
Ground-based gamma-ray astronomy aims at reconstructing the energy and direction of gamma rays from the extensive air showers they initiate in the atmosphere. Imaging Atmospheric Cherenkov Telescopes (IACT) collect the Cherenkov light induced by secondary charged particles in extensive air showers (EAS), creating an image of the shower in a camera positioned in the focal plane of optical systems. This image is used to evaluate the type, energy and arrival direction of the primary particle that initiated the shower. This contribution shows the results of a novel reconstruction method based on l…
The Cherenkov Telescope Array (CTA), with more than 100 telescopes, will be the largest ever ground-based gamma-ray observatory and is expected to greatly improve on both gamma-ray detection sensitivity and energy coverage compared to current-generation detectors. The 9.7-m Schwarzschild-Couder telescope (SCT) is one of the two candidates for the medium size telescope (MST) design for CTA. The novel aplanatic dual-mirror SCT design offers a wide field-of-view with a compact plate scale, allowing for a large number of camera pixels that improves the angular resolution and reduce the night sky b…
An important aspect of the calibration of the Cherenkov Telescope Array is the pointing, which enables an exact alignment of each telescope and therefore allows to transform a position in the sky to a point in the plane of the Cherenkov camera and vice versa. The favoured approach for the pointing calibration of the medium size telescopes (MST) is the installation of an optical CCD-camera in the dish of the telescope that captures the position of the Cherenkov camera and of the stars in the night sky simultaneously during data taking. The adaption of this approach is presented in this proceedi…
We have developed a prototype hexagonal light concentrator for the Large-Sized Telescopes of the Cherenkov Telescope Array. To maximize the photodetection efficiency of the focal-plane camera pixels for atmospheric Cherenkov photons and to lower the energy threshold, a specular film with a very high reflectance of 92-99% has been developed to cover the inner surfaces of the light concentrators. The prototype has a relative anode sensitivity (which can be roughly regarded as collection efficiency) of about 95 to 105% at the most important angles of incidence. The design, simulation, production …
The SST-1M telescope was developed as a prototype of a Small-Size-Telescope for the Cherenkov Telescope Array observatory and it has been extensively tested in Krakow since 2017. In this contribution we present validation of the Monte Carlo model of the prototype and expected performance in Krakow conditions. We focus on gamma/hadron separation and mono reconstruction of energy and gamma photon arrival direction using Machine learning methods.
The Cherenkov Telescope Array (CTA) is a future gamma-ray observatory that is planned to significantly improve upon the sensitivity and precision of the current generation of Cherenkov telescopes. The observatory will consist of several dozens of telescopes with different sizes and equipped with different types of cameras. Of these, the FlashCam camera system is the first to implement a fully digital signal processing chain which allows for a traceable, configurable trigger scheme and flexible signal reconstruction. As of autumn 2016, a prototype FlashCam camera for the medium-sized telescopes…
A single-mirror small-size (SST-1M) Davies-Cotton telescope with a dish diameter of 4 m has been built by a consortium of Polish and Swiss institutions as a prototype for one of the proposed small-size telescopes for the southern observatory of the Cherenkov Telescope Array (CTA). The design represents a very simple, reliable, and cheap solution. The mechanical structure prototype with its drive system is now being tested at the Institute of Nuclear Physics PAS in Krakow. Here we present the design of the prototype and results of the performance tests of the structure and the drive and control…
The Cherenkov Telescope Array (CTA) consortium aims to create the next generation Very High Energy gamma-ray observatory. It will be devoted to the observation of gamma rays over a wide band of energy, from 20 GeV to 300 TeV. Three different classes, Large, Medium and Small Size Telescopes, are foreseen to cover the low, intermediate and high energy regions, respectively. The energy range of the Small Size Telescopes (SSTs) extends from 1 TeV to 300 TeV. Among them, the Gamma-ray Cherenkov Telescope (GCT), a telescope based on a Schwarzschild-Couder dual-mirror optical design, is one of the pr…
A Large Size air Cherenkov Telescope (LST) prototype, proposed for the Cherenkov Telescope Array (CTA), is under construction at the Canary Island of La Palma (Spain) this year. The LST camera, which comprises an array of about 500 photomultipliers (PMTs), requires a precise and regular calibration over a large dynamic range, up to $10^3$ photo-electrons (pe's), for each PMT. We present a system built to provide the optical calibration of the camera consisting of a pulsed laser (355 nm wavelength, 400 ps pulse width), a set of filters to guarantee a large dynamic range of photons on the sensor…
We present the last developments on the IVOA Provenance data model, mainly based on the W3C PROV concept. In the context of the Cherenkov astronomy, the data processing stages imply both assumptions and comparison to dedicated simulations. As a consequence, Provenance information is crucial to the end user in order to interpret the high level data products. The Cherenkov Telescope Array (CTA), currently in preparation, is thus a perfect test case for the development of an IVOA standard on Provenance information. We describe general use-cases for the computational Provenance in the CTA producti…
The Gamma Cherenkov Telescope (GCT) is proposed to be part of the Small Size Telescope (SST) array of the Cherenkov Telescope Array (CTA). The GCT dual-mirror optical design allows the use of a compact camera of diameter roughly 0.4 m. The curved focal plane is equipped with 2048 pixels of ~0.2° angular size, resulting in a field of view of ~9°. The GCT camera is designed to record the flashes of Cherenkov light from electromagnetic cascades, which last only a few tens of nanoseconds. Modules based on custom ASICs provide the required fast electronics, facilitating sampling and digitisation as…
The Gamma-ray Cherenkov Telescope (GCT) is a candidate for the Small Size Telescopes (SSTs) of the Cherenkov Telescope Array (CTA). Its purpose is to extend the sensitivity of CTA to gamma-ray energies reaching 300 TeV. Its dual-mirror optical design and curved focal plane enables the use of a compact camera of 0.4 m diameter, while achieving a field of view of above 8 degrees. Through the use of the digitising TARGET ASICs, the Cherenkov flash is sampled once per nanosecond continuously and then digitised when triggering conditions are met within the analogue outputs of the photosensors. Enti…
The Cherenkov Telescope Array (CTA) is a forthcoming international ground-based observatory for very high-energy gamma rays. Its goal is to reach sensitivity five to ten times better than existing Cherenkov telescopes such as VERITAS, H.E.S.S. or MAGIC and extend the range of observation to energies down to few tens of GeV and beyond 100 TeV. To achieve this goal, an array of about 100 telescopes is required, meaning a total reflective surface of several thousands of square meters. Thence, the optimal technology used for CTA mirrors manufacture should be both low-cost (~1000 euros/m2) and allo…
The Gamma-ray Cherenkov Telescope (GCT) is one of the Small Size Telescopes (SSTs) proposed for the Cherenkov Telescope Array (CTA) aimed at the 1 TeV to 300 TeV energy range. GCT will be equipped with a Compact High-Energy Camera (CHEC) containing 2048 pixels of physical size about 6$\times$6~mm$^2$, leading to a field of view of over 8 degrees. Electronics based on custom TARGET ASICs and FPGAs sample incoming signals at a gigasample per second and provide a flexible triggering scheme. Waveforms for every pixel in every event are read out are on demand without loss at over 600 events per sec…
The Cherenkov Telescope Array (CTA) is a planned gamma-ray observatory. CTA will incorporate about 100 imaging atmospheric Cherenkov telescopes (IACTs) at a Southern site, and about 20 in the North. Previous IACT experiments have used up to five telescopes. Subsequently, the design of a graphical user interface (GUI) for the operator of CTA involves new challenges. We present a GUI prototype, the concept for which is being developed in collaboration with experts from the field of Human-Computer Interaction. The prototype is based on Web technology; it incorporates a Python web server, Web Sock…
A medium-sized Schwarzchild-Couder Telescope (SCT) is being developed as a possible extension for the Cherenkov Telescope Array (CTA). The Cherenkov camera of the telescope is designed to have 11328 silicon photomultiplier pixels capable of capturing high-resolution images of air showers in the atmosphere. The combination of the large number of pixels and the high trigger rate (> 5 kHz) expected for this telescope results in a multi-Gbps data throughput. This sets challenging requirements on the design and performance of a data acquisition system for processing and storing this data. A prototy…
