Qubits used in quantum computing tend to suffer from errors, either from the qubit interacting with the environment, or from imperfect control when quantum logic gates are applied. Fault-tolerant construction based on quantum error correcting codes (QECC) can be used to recover from such errors. Effective implementation of QECC requires a high fidelity readout of the ancilla qubits from which the error syndrome can be determined, without affecting the data qubits in which relevant quantum information is stored for processing. Here, we present a detection scheme for \yb trapped ion qubits, where we use superconducting nanowire single photon detectors and utilize photon time-of-arrival statistics to improve the fidelity and speed. Qubit shuttling allows for creating a separate detection region where an ancilla qubit can be measured without disrupting a data qubit. We achieve an average qubit state detection time of 11$μ$s with a fidelity of $99.931(6)\%$. The error due to the detection crosstalk, defined as the probability that the coherence of the data qubit is lost due to the process of detecting an ancilla qubit, is reduced to $\sim2\times10^{-5}$ by creating a separation of 370$μ$m between them.
Parasitic crosstalk in superconducting quantum devices is a leading limitation for quantum gates. We demonstrate the suppression of static ZZ crosstalk in a two-qubit, two-coupler superconducting circuit, where the frequency of a tunable coupler can be adjusted such that the ZZ interaction from each coupler destructively interfere. We verify the crosstalk elimination with simultaneous randomized benchmarking, and use a parametrically activated iSWAP interaction to achieve a Bell state preparation fidelity of 98.5% and a $\sqrt{\textrm{iSWAP}}$ gate fidelity of 94.8% obtained via quantum proces…
Measurement for qubits plays a key role in quantum computation. Current methods for classifying states of single qubit in a superconducting multi-qubit system produce fidelities lower than expected due to the existence of crosstalk, especially in case of frequency crowding. Here, We make the digital signal processing (DSP) system used in measurement into a shallow neural network and train it to be an optimal classifier to reduce the impact of crosstalk. The experiment result shows the crosstalk-induced readout error deceased by 100% after a 3-second optimization applied on the 6-qubit supercon…
Crosstalk is a major concern in the implementation of large-scale quantum computation since it can degrade the performance of qubit addressing and cause gate errors. Finding the origin of crosstalk and separating contributions from different channels are essential prerequisites for figuring out crosstalk mitigation schemes. Here, by performing circuit analysis of two coupled floating transmon qubits, we demonstrate that, even if the stray coupling, e.g., between a qubit and the drive line of its nearby qubit, is absent, microwave crosstalk between qubits can still exist due to the presence of …
One of the key challenges in current Noisy Intermediate-Scale Quantum (NISQ) computers is to control a quantum system with high-fidelity quantum gates. There are many reasons a quantum gate can go wrong -- for superconducting transmon qubits in particular, one major source of gate error is the unwanted crosstalk between neighboring qubits due to a phenomenon called frequency crowding. We motivate a systematic approach for understanding and mitigating the crosstalk noise when executing near-term quantum programs on superconducting NISQ computers. We present a general software solution to allevi…
Fixed-frequency qubits can suffer from always-on interactions that inhibit independent control. Here, we address this issue by experimentally demonstrating a superconducting architecture using qubits that comprise of two capacitively-shunted Josephson junctions connected in series. Historically known as tunable coupling qubits (TCQs), such two-junction qubits support two modes with distinct frequencies and spatial symmetries. By selectively coupling only one type of mode and using the other as our computational basis, we greatly suppress crosstalk between the data modes while permitting all-mi…
Magnetic flux tunability is an essential feature in most approaches to quantum computing based on superconducting qubits. Independent control of the fluxes in multiple loops is hampered by crosstalk. Calibrating flux crosstalk becomes a challenging task when the circuit elements interact strongly. We present a novel approach to flux crosstalk calibration, which is circuit model independent and relies on an iterative process to gradually improve calibration accuracy. This method allows us to reduce errors due to the inductive coupling between loops. The calibration procedure is automated and im…
Improving gate performance is vital for scalable quantum computing. The universal quantum computing also requires the gate fidelity to reach a high level. For superconducting quantum processor, which operates in the microwave band, the single-qubit gates are usually realized with microwave driving. The crosstalk between microwave pulses is a non-negligible error source. In this article, we propose an error mitigation scheme to address this crosstalk issue for single-qubit gates. There are three steps in our method. First, by controlling the detuning between qubits, the microwave induced classi…
Neural network approach to mitigating intra-gate crosstalk in superconducting CZ gates
Fujian Key Laboratory of Quantum Information and Quantum Optics, Fuzhou University（福建量子信息与量子光学重点实验室，福州大学）；Department of Physics, Fuzhou University（福州大学物理系）；Quantum Information Physics Theory Research Team, Center for Quantum Computing, RIKEN（理化学研究所量子计算中心量子信息物理理论研究组）；University of Michigan（密歇根大学）
Scalable quantum information processing requires that modular gate operations can be executed in parallel. The presence of crosstalk decreases the individual addressability, causing erroneous results during simultaneous operations. For superconducting qubits which operate in the microwave regime, electromagnetic isolation is often limited due to design constraints, leading to signal crosstalk that can deteriorate the quality of simultaneous gate operations. Here, we propose and demonstrate a method based on AC Stark effect for calibrating the microwave signal crosstalk. The method is suitable …
In this work we study the role of parasitic interactions and microwave crosstalk in a system of two superconducting artificial atoms interacting via a single-mode coplanar waveguide. Through a general description of the effective dynamics of the atoms, beyond the two-level approximation, we show that the atom selectivity (ability to individually address an atom) is only dependent on the resultant phasor associated to the drives used to control the system. We then exploit the benefits of such a drive-dependent selectivity to describe how the coherent population inversion occurs in the atoms sim…
We describe an efficient and scalable framework for modeling crosstalk effects on quantum information processors. By applying optimal control techniques, we show how to tuneup arbitrary high-fidelity parallel operations on systems with substantial local and nonlocal crosstalk. Simulations show drastically lower error rates for a 2D square array of 100 superconducting transmon qubits. These results suggest that rather than striving to engineer away undesirable interactions during fabrication, we can largely mitigate their effects through careful characterization and control optimization.
We analyze the crosstalk error mechanism in measurement of two capacitively coupled superconducting flux-biased phase qubits. The damped oscillations of the superconducting phase after the measurement of the first qubit may significantly excite the second qubit, leading to its measurement error. The first qubit, which is highly excited after the measurement, is described classically. The second qubit is treated both classically and quantum-mechanically. The results of the analysis are used to find the upper limit for the coupling capacitance (thus limiting the frequency of two-qubit operations…
We experimentally demonstrate that a superconducting nanowire single-photon detector is deterministically controllable by bright illumination. We found that bright light can temporarily make a large fraction of the nanowire length normally-conductive, can extend deadtime after a normal photon detection, and can cause a hotspot formation during the deadtime with a highly nonlinear sensitivity. In result, although based on different physics, the superconducting detector turns out to be controllable by virtually the same techniques as avalanche photodiode detectors. As demonstrated earlier, when …
Superconducting nanowire single-photon detectors (SNSPDs) perform single-photon counting with exceptional sensitivity and time resolution at near-infrared wavelengths. State-of-the-art SNSPDs, based on 100 nm-wide, 4 to 5 nm thick NbN nanowires, are vulnerable to constrictions, which significantly limit their yield. Also, their sensitivity becomes negligible beyond 2 μm wavelength, which makes them unsuitable for mid-infrared applications. SNSPDs based on few-tens-of-nanometer-wide nanowires are expected to efficiently detect mid-infrared photons and to operate at low bias currents, so constri…
Quantum computers built with superconducting artificial atoms already stretch the limits of their classical counterparts. While the lowest energy states of these artificial atoms serve as the qubit basis, the higher levels are responsible for both a host of attractive gate schemes as well as generating undesired interactions. In particular, when coupling these atoms to generate entanglement, the higher levels cause shifts in the computational levels that leads to unwanted $ZZ$ quantum crosstalk. Here, we present a novel technique to manipulate the energy levels and mitigate this crosstalk via …
Characterizing and Mitigating Flux Crosstalk in Superconducting Qubits-Couplers System
Academia Sinica（中央研究院）；Institute of Physics, Academia Sinica（中央研究院物理研究所）；National Taiwan University（台湾大学）；Department of Physics, National Taiwan University（台湾大学物理系）；Feng Chia University（逢甲大学）；Department of Electrical Engineering, Feng Chia University（逢甲大学电机工程学系）
We developed an electro thermal model of NbN superconducting nanowire avalanche photodetectors (SNAPs) on sapphire substrates. SNAPs are single photon detectors consisting of the parallel connection of N superconducting nanowires. We extrapolated the physical constants of the model from experimental data and we simulated the time evolution of the device resistance, temperature and current by solving two coupled electrical and thermal differential equations describing the nanowires. The predictions of the model were in good quantitative agreement with the experimental results.
We present a linearly arrayed, 16-element, superconducting nanowire single-photon detector with 83.4$\%$ system detection efficiency at 1550 nm and a mean per-element dead-time of 9.6-ns, enabling counting at 1 giga-count per second with $>50\%$ System Detection Efficiency. This device was designed and fabricated in an existing scalable commercial process.
Superconducting nanowire single photon detectors (SNSPDs) are fabricated directly on diamond substrates and their optical and electrical properties are characterized. Dark count performance and photon count rates are measured at varying temperatures for 1310nm and 632nm photons. The procedure to prepare diamond substrate surfaces suitable for the deposition and patterning of thin film superconducting layers is reported. Using this approach, diamond substrates with less than 300pm RMS surface roughness are obtained.
We present low-temperature measurements of low-loss superconducting nanowire-embedded resonators in the low-power limit relevant for quantum circuits. The superconducting resonators are embedded with superconducting nanowires with widths down to 20nm using a neon focused ion beam. In the low-power limit, we demonstrate an internal quality factor up to 3.9x10^5 at 300mK [implying a two-level-system-limited quality factor up to 2x10^5 at 10 mK], not only significantly higher than in similar devices but also matching the state of the art of conventional Josephson-junction-embedded resonators. We …
We report on simulation results that shows optimum photon absorption by superconducting nanowires can happen at a fill-factor that is much less than 100%. We also present experimental results on high performance of our superconducting nanowire single photon detectors realized using NbTiN on oxidized silicon.
Here we propose a new design paradigm for a superconducting nanowire single photon detector that uses a multi-layer architecture that places the electric leads beneath the nanowires. This allows for a very large number of detector elements, which we will call pixels in analogy to a conventional CCD camera, to be placed in close proximity. This leads to significantly better photon number resolution than current single and multi-nanowire meanders, while maintaining similar detection areas. We discuss the reset time of the pixels and how the design can be modified to avoid the latching failure se…
We demonstrate a 64-pixel free-space-coupled array of superconducting nanowire single photon detectors optimized for high detection efficiency in the near-infrared range. An integrated, readily scalable, multiplexed readout scheme is employed to reduce the number of readout lines to 16. The cryogenic, optical, and electronic packaging to read out the array, as well as characterization measurements are discussed.
We demonstrate niobium titanium nitride superconducting nanowires patterned on stoichiometric silicon nitride waveguides for detecting visible and infrared photons. The use of silicon nitride on insulator on silicon substrates allows us to simultaneously realize photonic circuits for visible and infrared light and integrate them with nanowire detectors directly on-chip. By implementing a traveling wave detector geometry in this material platform, we achieve efficient single photon detection for both wavelength regimes. Our detectors are an ideal match for integrated quantum optics as they prov…
Superconducting nanowire avalanche single-photon detectors (SNAPs) with n parallel nanowires are advantageous over single-nanowire detectors because their output signal amplitude scales linearly with n. However, the SNAP architecture has not been viably demonstrated for n > 4. To increase n for larger signal amplification, we designed a multi-stage, successive-avalanche architecture which used nanowires, connected via choke inductors in a binary-tree layout. We demonstrated an avalanche detector with n = 8 parallel nanowires and achieved eight-fold signal amplification, with a timing jitter of…
The origin of the decoherence in superconducting nanowire single-photon detectors, the so-called dark count, was investigated. We measured the direct-current characteristics and bias-current dependencies of the dark count rate in a wide range of temperatures from 0.5 K to 4 K, and analyzed the results by theoretical models of thermal fluctuations of vortices. Our results indicate that the current-assisted unbinding of vortex-antivortex pairs is the dominant origin of the dark count.
We demonstrate the fabrication of micron-wide tungsten silicide superconducting nanowire single-photon detectors on a silicon substrate using laser lithography. We show saturated internal detection efficiencies with wire widths from 0.59$μ$m to 1.43$μ$m under illumination at 1550nm. We demonstrate both straight wires, as well as meandered structures. Single-photon sensitivity is shown in devices up to 4mm in length. Laser-lithographically written devices allow for fast and easy structuring of large areas while maintaining a saturated internal efficiency for wire width around 1$μ$m.
We present a time-over-threshold readout technique to count the number of activated pixels from an array of superconducting nanowire single photon detectors (SNSPDs). This technique maintains the intrinsic timing jitter of the individual pixels, places no additional heatload on the cryostat, and retains the intrinsic count rate of the time-tagger. We demonstrate proof-of-principle operation with respect to a four-pixel device. Furthermore, we show that, given some permissible error threshold, the number of pixels that can be reliably read out scales linearly with the intrinsic signal-to-noise …
We demonstrate and verify quantum detector tomography of a superconducting nanowire single-photon detector (SNSPD) in a multiplexing scheme which permits measurement of up to 71000 photons per input pulse. We reconstruct the positive operator valued measure (POVM) of this device in the low photon-number regime, and use the extracted parameters to show the POVMs spanning the whole dynamic range of the device. We verify this by finding the mean photon number of a bright state. Our work shows that a reliable quantum description of large-scale SNSPD devices is possible, and should be applicable to…
We present the experimental demonstration of a superconducting photon number resolving detector. It is based on the series connection of N superconducting nanowires, each connected in parallel to an integrated resistor. The device provides a single voltage readout, proportional to the number of photons absorbed in distinct nanowires. Clearly separated output levels corresponding to the detection of n=1-4 photons are observed in a 4-element detector fabricated from an NbN film on GaAs substrate, with a single-photon system quantum efficiency of 2.6% at the wavelength of 1300nm. The series-nanow…
We present an active anti-latching system for superconducting nanowire single-photon detectors. We experimentally test it against a bright-light attack, previously used to compromise security of quantum key distribution. Although our system detects continuous blinding, the detector is shown to be partially blindable and controllable by specially tailored sequences of bright pulses. Improvements to the countermeasure are suggested.
We demonstrate a scalable readout scheme for an infrared single-photon pulse-position camera consisting of WSi superconducting nanowire single-photon detectors (SNSPDs). For an N x N array, only 2 x N wires are required to obtain the position of a detection event. As a proof-of-principle, we show results from a 2 x 2 array.
We measure the maximal distance at which two absorbed photons can jointly trigger a detection event in NbN nanowire superconducting single photon detector (SSPD) microbridges by comparing the one-photon and two-photon efficiency of bridges of different overall lengths, from 0 to 400 nm. We find a length of $23 \pm 2$ nm. This value is in good agreement with to size of the quasiparticle cloud at the time of the detection event.
We investigated the reset time of superconducting nanowire avalanche photodetectors (SNAPs) based on 30 nm wide nanowires. We studied the dependence of the reset time of SNAPs on the device inductance and discovered that SNAPs can provide a speed-up relative to SNSPDs with the same area, but with some limitations: (1) reducing the series inductance of SNAPs (necessary for the avalanche formation) could result in the detectors operating in an unstable regime; (2) a trade-off exists between maximizing the bias current margin and minimizing the reset time of SNAPs; and (3) reducing the reset time…
Superconducting nanowires, a mature technology originally developed for quantum sensing, can be used as a target and sensor with which to search for dark matter interactions with electrons. Here we report on a 180-hour measurement of a tungsten silicide superconducting nanowire device with a mass of 4.3 nanograms. We use this to place new constraints on dark matter--electron interactions, including the strongest terrestrial constraints to date on sub-MeV (sub-eV) dark matter that interacts with electrons via scattering (absorption) processes.
We use quantum detector tomography to investigate the detection mechanism in WSi nanowire superconducting single photon detectors (SSPDs). To this purpose, we fabricated a 250nm wide and 250nm long WSi nanowire and measured its response to impinging photons with wavelengths ranging from $λ$ = 900 nm to $λ$ = 1650 nm. Tomographic measurements show that the detector response depends on the total excitation energy only. Moreover, for energies Et > 0.8eV the current energy relation is linear, similar to what was observed in NbN nanowires, whereas the current-energy relation deviates from linear be…
We introduce a hybrid qubit based on a semiconductor nanowire with an epitaxially grown superconductor layer. Josephson energy of the transmon-like device ("gatemon") is controlled by an electrostatic gate that depletes carriers in a semiconducting weak link region. Strong coupling to an on-chip microwave cavity and coherent qubit control via gate voltage pulses is demonstrated, yielding reasonably long relaxation times (0.8 μs) and dephasing times (1 μs), exceeding gate operation times by two orders of magnitude, in these first-generation devices. Because qubit control relies on voltages rath…
We present a stable and high-performance fiber-coupled NbTiN superconducting nanowire avalanche photon detector (SNAP). We demonstrate afterpulse-free operation in serially connected two SNAPs (SC-2SNAP), even in the absence of a choke inductor, achieving a 7.7 times faster response speed than standard SSPDs. The SC-2SNAP device showed a system detection efficiency (SDE) of 81.0% with wide bias current margin, a dark count rate of 6.8 counts/s, and full width at half maximum timing jitter of 68 ps, operating at 2.3 K.
We developed superconducting nanowire single-photon detectors with an optical cavity (OC-SNSPDs) for multichannel systems. For efficient coupling, the devices were installed in compact fiber-coupled packages after their substrate thickness was reduced from 400 to 45 $μ$m. The measured detection efficiency (DE) measurement at different substrate thicknesses and the estimation of optical coupling efficiency indicated that ~98% of the input light beam could be radiated on a 15x15 $μm^2$ nanowire area from behind the substrate. The DEs of a NbN OC-SNSPD system were observed to be 9.5% and 25% at 1…
