Exfoliation of Few-Layer Black Phosphorus in Low-Boiling-Point Solvents and Its Application in Li-Ion Batteries
Antonio Esau Del Rio Castillo, Vittorio Pellegrini, Haiyan Sun, Joka Buha, Duc Anh Dinh, Emanuele Lago, Alberto Ansaldo, Andrea Capasso, Liberato Manna, Francesco Bonaccorso
The liquid-phase exfoliation (LPE) of black phosphorus (BP) is a strategic route for the large-scale production of phosphorene and few-layer BP (FL-BP) flakes. The exploitation of this exfoliated material in cutting-edge technologies, e.g., in flexible electronics and energy storage, is however limited by the fact that the LPE of BP is usually carried out at a high boiling point and in toxic solvents. In fact, the solvent residual is detrimental to device performance in real applications; thus, complete solvent removal is critical. Here, we tackle these issues by exfoliating BP in different low boiling-point solvents. Among these solvents, we find that acetone also provides a high concentration of exfoliated BP, leading to the production of FL-BP flakes with an average lateral size and thickness of c.a. 30 and 7 nm, respectively. The use of acetone to produce less defective few-layer BP flakes (FL-BPacetone) from bulk crystals is a straightforward process which enables the rapid preparation of homogeneous thin films thanks to the fast solvent evaporation. The ratio of edge to bulk atoms for the BP flakes here produced, combined with the use of low-boiling-point solvents for the exfoliation process suggests that these thin films are promising anodes for lithium-ion batteries. To this end, we tested Li-ion half cells with FL-BPacetone anodes achieving a reversible specific capacity of 480 mAh/g at a current density of 100 mA/g, over 100 charge/discharge cycles. Moreover, a reversible specific capacity of 345 mAh/g is achieved for the FL-BPacetone-based anode at a high current density (i.e., 1 A/g). These findings indicate that the FL-BPacetone-based battery is promising with regards to the design of fast charge/discharge devices. Overall, the presented process is a step forward toward the fabrication of phosphorene-based devices.
Forthcoming applications in electronics and optoelectronics make phosphorene a subject of vigorous research efforts. Solvent-assisted exfoliation of phosphorene promises affordable delivery in industrial quantities for future applications. We demonstrate, using equilibrium, steered and umbrella sampling molecular dynamics, that the 1-ethyl-3- methylimidazolium tetrafluoroborate [EMIM][BF4] ionic liquid is an excellent solvent for phosphorene exfoliation. The presence of both hydrophobic and hydrophilic moieties, as well as substantial shear viscosity, allows [EMIM][BF4] simultaneously to facil…
We demonstrate the large scale exfoliation of bulk black phosphorus into few-layers black phosphorus. We use wet-jet mill (WJM) as an industrially scalable exfoliation technique. In order to avoid the degradation by oxidation of the exfoliated flakes, the few-layers black phosphorus is protected by functionalisation (with 4-bromobenzene-diazonium tetrafluoroborate) during the exfoliation process. We used the exfoliated and functionalised flakes as fillers in a polymethyl methacrylate matrix to test the mechanical endurance, obtaining an improvement in the Young modulus of 106% compared to the …
Solution dispersions of two-dimensional (2D) black phosphorus (BP), often referred to as phosphorene, are achieved by solvent exfoliation. These pristine, electronic-grade BP dispersions are produced with anhydrous, organic solvents in a sealed tip ultrasonication system, which circumvents BP degradation that would otherwise occur via solvated oxygen or water. Among conventional solvents, n-methyl-pyrrolidone (NMP) is found to provide stable, highly concentrated (~0.4 mg/mL) BP dispersions. Atomic force microscopy, scanning electron microscopy, transmission electron microscopy, Raman spectrosc…
Few layer black phosphorus is a new two-dimensional material which is of great interest for applications, mainly in electronics. However, its lack of stability severely limits our ability to synthesise and process this material. Here we demonstrate that high-quality, few-layer black phosphorus nanosheets can be produced in large quantities by liquid phase exfoliation in the solvent N-cyclohexyl-2-pyrrolidone (CHP). We can control nanosheet dimensions and have developed metrics to estimate both nanosheet size and thickness spectroscopically. When exfoliated in CHP, the nanosheets are remarkably…
The tunable bandgap from 0.3 eV to 2 eV of black phosphorus (BP) makes it to fill the gap in graphene. When studying the properties of BP more comprehensive, scientists have discovered that many two-dimensional materials, such as tellurene, antimonene, bismuthene, indium selenide and tin sulfide, have similar structures and properties to black phosphorus thus called black phosphorus analogs. In this review, we briefly introduce preparation methods of black phosphorus and its analogs, with emphasis on the method of mechanical exfoliation (ME), liquid phase exfoliation (LPE) and chemical vapor d…
Understanding and exploiting the remarkable optical and electronic properties of phosphorene require mass production methods that avoid chemical degradation. While solution-based strategies have been developed for scalable exfoliation of black phosphorus, these techniques have thus far employed anhydrous organic solvents in an effort to minimize exposure to known oxidants, but at the cost of limited exfoliation yield and flake size distribution. Here, we present an alternative phosphorene production method based on surfactant-assisted exfoliation and post-processing of black phosphorus in deox…
Isolation and characterization of mechanically exfoliated black phosphorus flakes with a thickness down to two single-layers is presented. A modification of the mechanical exfoliation method, which provides higher yield of atomically thin flakes than conventional mechanical exfoliation, has been developed. We present general guidelines to determine the number of layers using optical microscopy, Raman spectroscopy and transmission electron microscopy in a fast and reliable way. Moreover, we demonstrate that the exfoliated flakes are highly crystalline and that they are stable even in free-stand…
The experimental exfoliation of layered group-IV monochalcogenides --semiconductors isostructural to black phosphorus-- using processes similar to those followed in the production of graphene or phosphorene has turned out unsuccessful thus far, as if the chemical degradation observed in black phosphorus was aggravated in these monochalcogenides. Here, we document a facile dissociation of water by these materials within ten nanoseconds from room-temperature Car-Parrinello molecular dynamics calculations under standard temperature and pressure conditions. These results suggest that humidity must…
Raman scattering and photoluminescence spectroscopy are used to investigate the optical properties of single layer black phosphorus obtained by mechanical exfoliation of bulk crystals under an argon atmosphere. The Raman spectroscopy, performed in situ on the same flake as the photoluminescence measurements, demonstrates the single layer character of the investigated samples. The emission spectra, dominated by excitonic effects, display the expected in plane anisotropy. The emission energy depends on the type of substrate on which the flake is placed due to the different dielectric screening. …
Bulk black phosphorus (BP) consists of puckered layers of phosphorus atoms. Few-layer BP, obtained from bulk BP by exfoliation, is an emerging candidate as a channel material in post-silicon electronics. A deep understanding of its physical properties and its full range of applications are still being uncovered. In this paper, we present a theoretical and experimental investigation of phonon properties in few-layer BP, focusing on the low-frequency regime corresponding to interlayer vibrational modes. We show that the interlayer breathing mode A3g shows a large redshift with increasing thickne…
Phosphorene, a two-dimensional (2D) monolayer of black phosphorus, has attracted considerable theoretical interest, although the experimental realization of monolayer, bilayer, and few-layer flakes has been a significant challenge. Here we systematically survey conditions for liquid exfoliation to achieve the first large-scale production of monolayer, bilayer, and few-layer phosphorus, with exfoliation demonstrated at the 10-gram scale. We describe a rapid approach for quantifying the thickness of 2D phosphorus and show that monolayer and few-layer flakes produced by our approach are crystalli…
Water is believed to be harmful for the stability of phosphorene.On the contrary, the presence of small amount of water allows the synthesis of high-quality material in liquid exfoliation of black phosphorus using dimethylsulfoxide as solvent. A phosphorus/water molar ratio between 1.5 and 14 maximizes the quality of the phosphorene flakes and their stability.
We propose here a two-dimensional material based on a single layer of violet or Hittorf's phosphorus. Using first-principles density functional theory, we find it to be energetically very stable, comparable to other previously proposed single-layered phosphorus structures. It requires only a small energetic cost of approximately $0.04~\text{eV/atom}$ to be created from its bulk structure, Hittorf's phosphorus, or a binding energy of $0.3-0.4~\text{J/m}^2$ per layer, suggesting the possibility of exfoliation in experiments. We find single-layered Hittorf's phosphorus to be a wide band gap semic…
The rational design of transition metal dichalcogenide electrocatalysts for efficiently catalyzing hydrogen evolution reaction (HER) is believed to lead to the generation of a renewable energy carrier. To this end our work has made three main contributions. At first, we have demonstrated that exfoliation via ionic liquid assisted grinding combined with gradient centrifugation is an efficient method to exfoliate bulk WS2 to nanosheets with a thickness of a few atomic layers and lateral size dimensions in the range of 100 nm to 2 nm. These WS2 nanosheets decorated with scattered nanodots exhibit…
Phosphorene is a novel two-dimensional material that can be isolated through mechanical exfoliation from layered black phosphorus, but unlike graphene and silicene, monolayer phosphorene has a large band gap. It was thus unsuspected to exhibit band inversion and the ensuing topological insulator behavior. It has recently attracted interest because of its proposed application as field effect transistors. Using first-principles calculations with applied perpendicular electric field F we predict a continuous transition from the normal insulator to a topological insulator and eventually to a metal…
The scalable and high-efficiency production of two-dimensional (2D) materials is a prerequisite to their commercial use. Currently, only graphene and graphene oxide can be produced on a ton scale, and the inability to produce other 2D materials on such a large scale hinders their technological applications. Here we report a grinding exfoliation method that uses micro-particles as force intermediates to resolve applied compressive forces into a multitude of small shear forces, inducing the highly-efficient exfoliation of layer materials. The method, referred to as intermediate-assisted grinding…
Few-layer black phosphorus, a new elemental 2D material recently isolated by mechanical exfoliation, is a high-mobility layered semiconductor with a direct bandgap that is predicted to strongly depend on the number of layers, from 0.35 eV (bulk) to 2.0 eV (single-layer). Therefore, black phosphorus is an appealing candidate for tunable photodetection from the visible to the infrared part of the spectrum. We study the photoresponse of field-effect transistors (FETs) made of few-layer black phosphorus (3 nm to 8 nm thick), as a function of excitation wavelength, power and frequency. In the dark …
The recent isolation of atomically thin black phosphorus by mechanical exfoliation of bulk layered crystals has triggered an unprecedented interest, even higher than that raised by the first works on graphene and other two-dimensional, in the nanoscience and nanotechnology community. In this Perspective we critically analyze the reasons behind the surge of experimental and theoretical works on this novel two-dimensional material. We believe that the fact that black phosphorus band gap value spans over a wide range of the electromagnetic spectrum that was not covered by any other two-dimensiona…
Black phosphorus (bP) has been recently investigated for next generation nanoelectronic multifunctional devices. However, the intrinsic instability of exfoliated bP (the bP nanoflakes) towards both moisture and air has so far overshadowed its practical implementation. In order to contribute to fill this gap, we report here the preparation of new hybrid polymer-based materials where bP nanoflakes exhibit a significantly improved stability. The new materials have been prepared by different synthetic paths including: i) the mixing of conventionally liquid-phase exfoliated bP (in DMSO) with PMMA s…
Single layer (SL) phosphorus (phosphorene) has drawn considerable research attention recently as a two-dimensional (2D) material for application promises. It is a semiconductor showing superior transport and optical properties. Few-layer or SL black phosphorus has been successfully isolated by exfoliation from bulk crystals and extensively studied thereof for its electronic and optical properties. Blue phosphorus (blueP), an allotrope of black phosphorus where atoms are arranged in a more flat atomic configuration, has been recently suggested by theory to exist in the SL form on some substrate…
Black phosphorus (BP) has attracted significant interest as a monolayer or few-layer material with extraordinary electrical and optoelectronic properties. However, degradation in air and other environments is an unresolved issue that may limit future applications. In particular the role of different ambient species has remained controversial. Here, we report systematic experiments combined with ab-initio calculations that address the effects of oxygen and water in the degradation of BP. Our results show that BP rapidly degrades whenever oxygen is present, but is unaffected by deaerated (i.e., …
Hybrid materials, containing a 2D filler embedded in a polymeric matrix, are an interesting platform for several applications, because of the variety of properties that the filler can impart to the polymer matrix when dispersed at the nanoscale. Moreover, novel properties could arise from the interaction between the two. Mostly the bulk properties of these materials have been studied so far, especially focusing on how the filler changes the polymeric matrix properties. Here we propose a complete change of perspective by using the hybrid nanocomposite material as a platform suitable to engineer…
Anisotropic thermo-mechanical response of layered hexagonal boron nitride and black phosphorus: application as a simultaneous pressure and temperature sensor
Discovery of atomically thin black phosphorus (called phosphorene) holds promise to be used as an alternative two-dimensional material to graphene and transition metal dichalcogenides especially as an anode material for lithium-ion batteries (LIBs). However, at present bulk black phosphorus (BP) still suffers from rapid capacity fading that results in poor rechargeable performance. Here, for the first time, we use in situ transmission electron microscopy (TEM) to construct nanoscale phosphorene LIBs and visualize the capacity fading mechanism in thick multilayer phosphorene by real time captur…
Magnetic van der Waals (vdW) materials have been heavily pursued for fundamental physics as well as for device design. Despite the rapid advances, so far magnetic vdW materials are mainly insulating or semiconducting, and none of them possesses a high electronic mobility - a property that is rare in layered vdW materials in general. The realization of a magnetic high-mobility vdW material would open the possibility for novel magnetic twistronic or spintronic devices. Here we report very high carrier mobility in the layered vdW antiferromagnet GdTe3. The electron mobility is beyond 60,000 cm2 V…
