arXivDaily arXiv每日学术速递 周一至周五更新
arXiv 1706.05917eess.SYcs.SY
收藏

基于PMU测量的输电线路参数识别

Transmission line parameter identification using PMU measurements

Arizona State University(亚利桑那州立大学);Salt River Project(盐河项目)

Di Shi, Daniel J. Tylavsky, Kristian M. Koellner, Naim Logic, David E. Wheeler

AI总结:

本文提出一种基于线性估计理论的新方法,用于更可靠地识别输电线路参数,包括正序、负序和零序参数及不同序之间的互阻抗,适用于各种输电线路情况。

摘要:

准确了解输电线路(TL)的阻抗参数有助于提高继电保护设置和功率流建模的准确性。为了提高TL参数估计的精度,过去已提出各种算法,基于Phasor Measurement Units(PMUs)的测量数据来识别TL参数。这些方法基于正序TL模型,可以在测量噪声不存在时生成准确的正序阻抗参数,但对于未完全换位或存在测量噪声的TL可能会生成错误参数。PMU现场测量数据常被噪声破坏,这对所有参数识别算法都是问题,尤其是应用于短输电线路时更明显。本文分析了在未换位的TL上使用正序TL模型时的局限性,并提出了一种新的方法,利用线性估计理论来更可靠地识别TL参数。该方法可以用于最一般的情况:短或长线路,无论是完全换位还是未换位,具有平衡或不平衡负载。除了正序或负序阻抗参数外,所提出的方法还可用于估计零序参数及不同序之间的互阻抗。本文还考察了PMU数据中的噪声对TL参数计算的影响。基于ATP模拟数据进行了几个案例研究,以验证新方法的有效性。通过比较由该新方法和其他方法生成的结果,证明了所提出方法的有效性。

英文摘要:

Accurate knowledge of transmission line (TL) impedance parameters helps to improve accuracy in relay settings and power flow modeling. To improve TL parameter estimates, various algorithms have been proposed in the past to identify TL parameters based on measurements from Phasor Measurement Units (PMUs). These methods are based on the positive sequence TL models and can generate accurate positive sequence impedance parameters for a fully-transposed TL when measurement noise is absent; however these methods may generate erroneous parameters when the TLs are not fully transposed or when measurement noise is present. PMU field-measure data are often corrupted with noise and this noise is problematic for all parameter identification algorithms, particularly so when applied to short transmission lines. This paper analyzes the limitations of the positive sequence TL model when used for parameter estimation of TLs that are untransposed and proposes a novel method using linear estimation theory to identify TL parameters more reliably. This method can be used for the most general case: short or long lines that are fully transposed or untransposed and have balanced or unbalance loads. Besides the positive or negative sequence impedance parameters, the proposed method can also be used to estimate the zero sequence parameters and the mutual impedances between different sequences. This paper also examines the influence of noise in the PMU data on the calculation of TL parameters. Several case studies are conducted based on simulated data from ATP to validate the effectiveness of the new method. Through comparison of the results generated by this novel method and several other methods, the effectiveness of the proposed approach is demonstrated.

机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。

↑