arXivDaily arXiv每日学术速递 周一至周五更新
arXiv 1705.07486physics.acc-phphysics.ins-det
收藏

用于在线束流发射度测量和质子束流表征的系统

A system for online beam emittance measurements and proton beam characterization

K. P. Nesteruk, M. Auger, S. Braccini, T. S. Carzaniga, A. Ereditato, P. Scampoli

摘要:

研制了一套在线测量束流发射度的系统。它被命名为$^{4}$ PrOB $\varepsilon$ aM(4-Profiler Online束流发射度Measurement),旨在使用多束流轮廓仪方法快速有效地测量发射度。该系统的核心由四个连续的UniBEaM轮廓仪组成,这些轮廓仪基于穿过光束的石英光纤。$^{4}$ PrOB $\varepsilon$ aM系统用于伯尔尼大学医院(Inselspital)IBA Cyclone 18 MeV回旋加速器产生的18 MeV质子束的表征研究。该机器用于日常放射性同位素生产和多学科研究,这是通过专门设计的束流传输线(BTL)进行的。测量了回旋加速器的横向有效值束流发射度随磁场、RF峰值电压和剥离器方位角等机器参数的变化。利用基于四极强度变化的方法测量了束流发射度。为了表征纵向动力学,测量了质子的能量分布。为此,开发了一种基于不同厚度的铝吸收体、UniBEaM检测器和法拉第杯的方法。结果是在MAD-X软件中开发的BTL模拟的输入。该工具允许在线调整机器参数,并针对特定应用优化光束特性。

英文摘要:

A system for online measurement of the transverse beam emittance was developed. It is named $^{4}$PrOB$\varepsilon$aM (4-Profiler Online Beam Emittance Measurement) and was conceived to measure the emittance in a fast and efficient way using the multiple beam profiler method. The core of the system is constituted by four consecutive UniBEaM profilers, which are based on silica fibers passing across the beam. The $^{4}$PrOB$\varepsilon$aM system was deployed for characterization studies of the 18~MeV proton beam produced by the IBA Cyclone 18 MeV cyclotron at Bern University Hospital (Inselspital). The machine serves daily radioisotope production and multi-disciplinary research, which is carried out with a specifically conceived Beam Transport Line (BTL). The transverse RMS beam emittance of the cyclotron was measured as a function of several machine parameters, such as the magnetic field, RF peak voltage, and azimuthal angle of the stripper. The beam emittance was also measured using the method based on the quadrupole strength variation. The results obtained with both techniques were compared and a good agreement was found. In order to characterize the longitudinal dynamics, the proton energy distribution was measured. For this purpose, a method was developed based on aluminum absorbers of different thicknesses, a UniBEaM detector, and a Faraday cup. The results were an input for a simulation of the BTL developed in the MAD-X software. This tool allows machine parameters to be tuned online and the beam characteristics to be optimized for specific applications.

机构、总结、中文摘要均由AI分析而来,可能存在错误,请以论文正文为准。

↑