Chromium substituted cobalt ferrite with grain size less than the single domain (approx. 70 nm) has been prepared by the sol-gel method. XRD analysis reveals that the samples crystallize to cubic symmetry with spacegroup number 227. Two transition temperatures (TD (approx. 450 K) and TM (approx. 600 K) have been observed from the impedance verses temperature measurement. TD increases with the increase in frequency due to dipole response to the frequency. TM is comparable with the para-ferrimagnetic transition temperature of cobalt ferrite, which is independent of frequency. This result is well supported by the temperature dependent DC conductivity measurement. The modified Debye relaxation could be explained the impedance spectra of CoFe2-xCrxO4. The grain and grain boundary effect on impedance spectroscopy has been observed from Cole-Cole analysis. The ac conductivity follows Arrhenius behavior at different frequencies. All the samples exhibit the negative temperature coefficient of resistance behavior which reveals the semiconducting behavior of the material. The Mott VRH model could explain the DC electrical conductivity. Both ac impedance and DC resistivity are well co-related each other to explain the electron transport properties in Cr substituted cobalt ferrite. The electrical transport properties could be explained by the electron hopping between different metal ions via oxygen in the material.
Zinc oxide and Aluminum Ferrite were prepared Chemical route. The samples were characterized by XRD and VSM. Simulation of M-H plots of Co/CoO thin films were performed. Effect of parameters was observed on saturation magnetization.
The temperature dependence of core loss in cobalt substituted Ni-Zn-Cu ferrites was investigated. Co2+ ions are known to lead to a compensation of the magneto-crystalline anisotropy in Ni-Zn ferrites, at a temperature depending on the cobalt content and the Ni/Zn ratio. We observed similar behaviour in Ni-Zn-Cu and it was found that the core loss goes through a minimum around this magneto-crystalline anisotropy compensation. Moreover, the anisotropy induced by the cobalt allowed a strong decrease of core loss, a ferrite having a core loss of 350 mW/cm3 at 80 ^\circ C was then developed (measur…
Cobalt ferrite nanoparticles have been synthesized using a co-precipitation approach. Co:Fe precursor ratio is varied over a certain window (1.05 to 1.2). It is observed that the 1.15:2 precursor ratio gives better phase control but poor coercivity. On the other hand, 1.05:2 precursor ratio results in substantially better coercivity values (274kA/m; almost 300% the value reported for co-precipitated cobalt ferrite by Praveena et al.), but moderate BH product maximum (2.25 kJ/m3; ~ comparable to many reports on cobalt ferrite nanoparticles so far). The nanoparticles with best coercivity are ann…
Cobalt substitutions were investigated in Ni0.4Zn0.4Cu0.2Fe2O4 ferrites, initial complex permeability was then measured from 1 MHz to 1 GHz. It appears that cobalt substitution led to a decrease in the permeability and an increase in the \mus\timesfr factor. As well, it gave to the permeability spectrum a sharp resonance character. We also observed a spin reorientation occurring at a temperature depending on the cobalt content. Study of the complex permeability versus temperature highlighted that the most resonant character was obtained at this temperature. This shows that cobalt contribution …
Magnetic nanoparticles of cobalt ferrite have been synthesized by wet chemical method using stable ferric and cobalt salts with oleic acid as the surfactant. X-ray Diffraction (XRD) and Transmission Electron Microscope (TEM) confirmed the formation of single phase cobalt ferrite nanoparticles in the range 15-48nm depending on the annealing temperature and time. The size of the particles increases with annealing temperature and time while the coercivity goes through a maximum, peaking at around 28nm. A very large coercivity (10.5kOe) is observed on cooling down to 77K while typical blocking eff…
The direct liquid injection chemical vapor deposition (DLI-CVD) technique has been used for the growth of cobalt ferrite (CFO) films on (100)-oriented MgAl$_2$O$_4$ (MAO) substrates. Smooth and highly epitaxial cobalt ferrite thin films, with the epitaxial relationship $\mathrm{MAO} (100)\:[001] \parallel \mathrm{CFO} (100)\:[001]$, are obtained under optimized deposition conditions. The films exhibit bulk-like structural and magnetic properties with an out-of-plane lattice constant of $8.370\;\mathrmÅ$ and a saturation magnetization of $420\;\mathrm{kA/m}$ at room temperature. The Raman spect…
In this work, a successful synthesis of magnetic cobalt ferrite (CoFe2O4) nanoparticles is presented. The synthesized CoFe2O4 nanoparticles have a spherical shape and highly monodisperse in the selected solvent. The effect of different reaction conditions such as temperature, reaction time and varying capping agents on the phase and morphology is studied. Scanning transmission electron microscopy showed that the size of these nanoparticles can be controlled by varying reaction conditions. Both X-ray diffraction and energy dispersive X-ray spectroscopy corroborate the formation of CoFe2O4 spine…
We present magnetostriction and magnetization measurements of a cobalt ferrite Co0.8Fe2.2O4 single crystal. We observe unusual behaviour in the magnetic hard axis of the single crystal which manifests in a jump of the magnetization curve at a critical field. This first order magnetization process (FOMP) which is explained as an anisotropy driven transition is visible at temperatures lower than 150 K. By analyzing the anisotropy constants we found that the higher order anisotropy constant K2 dominates the anisotropy energy. In the magnetostriction measurements the FOMP is clearly visible as a h…
The mixed ferrite-cobaltites LnFe0.5Co0.5O3, with Ln = Eu & Dy have been prepared by a sol-gel method and the samples have been characterized using X-ray diffraction and electron microscopy. The magnetic investigations reveal that both samples ordered in canted antiferromagnetic structures near room temperature. The Dzyaloshinskii-Moriya or antisymmetric exchange interaction induces weak ferromagnetism due to canting of the antiferromagnetically ordered spins. In the case of Ln-Fe-Co orthoferrites, two magnetic sublattices (Ln3+-4f and Fe3+/Co3+-3d) generally align in opposite directions and i…
Low frequency magnetoelectric (ME) coupling has been investigated in bulk and multilayers of cobalt zinc ferrite, Co1-xZnxFe2O4 (x=0-0.6), and lead zirconate titanate. In bulk samples, the transverse and longitudinal couplings are weak and are of equal magnitude. A substantial strengthening of ME interactions is evident in layered structures, with the ME voltage coefficient a factor of 10-30 higher than in bulk samples. Important findings of the studies in layered composites are as follows. (i) The transverse coupling is stronger than the longitudinal coupling. (ii) The strength of ME interact…
CoFe2O4 thin films (5 nm and 20 nm thick) were grown by oxygen assisted molecular beam epitaxy on Pt(111) at 523~K and subsequently annealed at 773 K in vacuum or oxygen. They were characterized in-situ using Auger Electron Spectroscopy, Low-Energy Electron Diffraction, Scanning Tunneling Microscopy and Conversion Electron Mössbauer Spectroscopy. The as-grown films were composed of small, nanometric grains. Annealing of the films produced an increase in the grain size and gave rise to magnetic order at room temperature, although with a fraction of the films remaining in the paramagnetic state.…
In this work we report a study of the magnetic behavior of ferrimagnetic oxide CoFe2O4 treated by mechanical milling with different grinding balls. The cobalt ferrite nanoparticles were prepared using a simple hydrothermal method and annealed at 500oC. The non-milled sample presented coercivity of about 1.9 kOe, saturation magnetization of 69.5 emu/g, and a remanence ratio of 0.42. After milling, two samples attained coercivity of 4.2 and 4.1 kOe, and saturation magnetization of 67.0 and 71.4 emu/g respectively. The remanence ratio MR/MS for these samples increase to 0.49 and 0.51, respectivel…
Perpendicular magnetic anisotropy (PMA) energy up to $K_{\mathrm{u}}=6.1\pm0.8$ MJ m$^{-3}$ is demonstrated in this study by inducing large lattice-distortion exceeding 3% at room temperature in epitaxially distorted cobalt ferrite Co$ _{x} $Fe$ _{3-x} $O$ _{4} $ (x = 0.72) (001) thin films. Although the thin film materials include no rare-earth elements or noble metals, the observed $ K_{u} $ is larger than that of the neodymium-iron-boron compounds for high-performance permanent magnets. The large PMA is attributed to the significantly enhanced magneto-elastic effects, which are pronounced i…
The magnetization of thin films of cobalt ferrite frequently falls far below the bulk value of 455 kAm-1, which corresponds to an inverse cation distribution in the spinel structure with a significant orbital moment of about 0.6 muB that is associated with the octahedrally-coordinated Co2+ ions. The orbital moment is responsible for the magnetostriction and magnetocrystalline anisotropy, and its sensitivity to imposed strain. We have systematically investigated the structure and magnetism of films produced by pulsed-laser deposition on different substrates (TiO2, MgO, MgAl2O4, SrTiO3, LSAT, La…
We report direct experimental evidence of room temperature spin filtering in magnetic tunnel junctions (MTJs) containing CoFe2O4 tunnel barriers via tunneling magnetoresistance (TMR) measurements. Pt(111)/CoFe2O4(111)/gamma-Al2O3(111)/Co(0001) fully epitaxial MTJs were grown in order to obtain a high quality system, capable of functioning at room temperature. Spin polarized transport measurements reveal significant TMR values of -18% at 2 K and -3% at 290 K. In addition, the TMR ratio follows a unique bias voltage dependence that has been theoretically predicted to be the signature of spin fil…
CoFe2O4 nanoparticles were synthesized using gelatin as a polymerizing agent. Structural, morphological and magnetic properties of samples treated at different temperatures were investigated by X-ray diffraction, scanning electron microscopy, Mossbauer spectroscopy and magnetization measurements. Our results revealed that the samples annealed at 623 K and temperatures above 973 K have a cation distributions given by (Co0.19Fe0.81)[Co0.81Fe1.19]O4 and (Co0.06Fe0.94)[Co0.94Fe1.06]O4, respectively. The particle sizes varied from 73 to 296 nm and the magnetocrystalline anisotropy, K1, has values r…
Cobalt ferrite ultrathin films with inverse spinel structure are among the best candidates for spin-filtering at room temperature. We have fabricated high-quality epitaxial ultrathin CoFe2O4 layers on Ag(001) following a three-step method: an ultrathin metallic CoFe2 alloy was first grown in coherent epitaxy on the substrate, and then treated twice with O2, first at RT and then during annealing. The epitaxial orientation, the surface, interface and film structure were resolved combining LEED, STM, Auger and in situ GIXRD. A slight tetragonal distortion was observed, that should drive the easy …
In this study we have compared magnetic, magnetostrictive and piezomagnetic properties of isotropic and anisotropic cobalt ferrite pellets. The isotropic sample was prepared by the ceramic method while the sample exhibiting uniaxial anisotropy was made by reactive sintering using Spark Plasma Sintering (SPS). This technique permits to induce a magnetic anisotropy in cobalt ferrite in the direction of the applied pressure during SPS process. Sample with uniaxial anisotropy revealed a higher longitudinal magnetostriction and piezomagnetism compared to the isotropic sample, but the transversal ma…
Magnetic nanomaterials (23-43 nm) of Cu$_x$Co$_{1-x}$Fe$_2$O$_4$\ (x = 0.0, 0.5 and 1.0) were synthesized by auto combustion method. The crystallite sizes of these materials were calculated from X-ray diffraction peaks. The band observed in Fourier transform infrared spectrum near 575 cm$^{-1}$ in these samples confirm the presence of ferrite phase. Conductivity measurement shows the thermal hysteresis and demonstrates the knee points at 475$^o$C, 525$^o$C and 500$^o$C for copper ferrite, cobalt ferrite and copper-cobalt mixed ferrite respectively. The hystersis M-H loops for these materials w…
The magnetization behaviour of the soft Cobalt Ferrite-hard Strontium Ferrite nanocomposite is tuned from the non exchange spring nature to the exchange spring nature, by controlling the particle size of the soft Cobalt Ferrite in the Cobalt Ferrite: Strontium Ferrite (1:8) nanocomposite. The relative strength of the interaction governing the magnetization process in the nanocomposites is investigated using Henkel plot and First Order Reversal Curve (FORC) method. The FORC method has been utilized to understand the magnetization reversal behaviour as well as the extent of the irreversible magn…
Magnetoelectric Coupling in Nickel-Cobalt Ferrite and Lanthanum Ferrite Heterostructure Composites: Experimental Evidence and Simulation-Driven Insights
The synthesis of layered ferrite-lead titanate zirconate (PZT) and lanthanum nanganite-PZT and the observation of giant magneto-electric interactions are discussed. The ferrites used in our studies included pure and Zn substituted cobalt-, nickel- and lithium ferrites. Ferromagnetic manganites used included both calcium and strontium substituted systems. The samples were prepared from 10-40 mm thick films obtained by tape-casting. Our studies showed strong ME coupling in manganite-PZT and cobalt zinc ferrite-PZT, and a giant ME effect in nickel zinc ferrite-PZT. We found evidence for Zn assist…
A detailed correlative structural, magnetic and chemical analysis of non-stoichiometric cobalt ferrite micrometric crystals was performed by x-ray magnetic circular dichroism combined with photoemission microscopy, low energy electron microscopy, and atomic force microscopy. The vector magnetization at the nanoscale is obtained from magnetic images at different x-ray incidence angles and compared with micromagnetic simulations, revealing the presence of defects which pin the magnetic domain walls. A comparison of different types of defects and the domain walls location suggests that the main s…
We prepared very high-coercivity cobalt ferrite nanoparticles using short-time high-energy mechanical milling. After the milling process, the coercivity of the nanoparticles reached 3.75 kOe - a value almost five times higher than that obtained for the non-milled sample. We performed a thermal treatment on the milled sample at 300, 400, and 600 oC for 30 and 180 mins, and studied the changes in the magnetic parameters due to the thermal treatment using the hysteresis curves, Williamson-Hall analysis, and transmission electron microscopy. The thermal treatment at 600 oC causes a decrease in the…
Magnetoelectric interactions in bilayers of magnetostrictive and piezoelectric phases are mediated by mechanical deformation. Here we discuss the theory and companion data for magnetoelectric (ME) coupling at electromechanical resonance (EMR) in a ferrite-lead zirconate titanate (PZT) bilayer. Estimated ME voltage coefficient versus frequency profiles for nickel, cobalt, or lithium ferrite and PZT reveal a giant ME effect at EMR with the highest coupling expected for cobalt ferrite-PZT. Measurements of resonance ME coupling have been carried out on layered and bulk composites of nickel ferrite…
In-depth investigations of size and occupancies in cobalt ferrite nanoparticles by joint Rietveld refinements of X-ray and neutron powder diffraction data
Layered ferromagnetic-piezoelectric composites show mechanical strain mediated electromagnetic coupling. Here we discuss dielectric and piezoelectric properties of ferrite-lead zirconate titanate (PZT) and lanthanum manganite-PZT samples. Results of our investigations on dielectric and pyroelectric properties of multilayer ferromagnetic-piezoelectric are presented here. Lead zircinate-titanate PbZrxTi1-xO3 (PZT) was used for the piezoelectric phase in all the structures. The following materials were used for the ferromagnetic component: nickel-zinc ferrites Ni0.9Zn 0.1Fe2O4 (NFO1) and Ni0.8Zn0…
Enhancement in Magnetic and Magnetocaloric Properties of CoFe2O4 Nanofibers at Lower Temperatures
Cadi- Ayyad University（卡迪·阿亚德大学）；Jozef Stefan Institute（约瑟夫·斯蒂芬研究所）；University of Picardie Jules Verne（皮卡第朱尔·凡尔纳大学）；Institute of Mathematics, Physics and Mechanics & University of Ljubljana, Faculty of Civil and Geodetic Engineering（卢布尔雅那大学土木与测量工程学院数学、物理与力学研究所）
