Millimeter wave (mmWave) systems are emerging as an essential technology to enable extremely high data rate wireless communications. The main limiting factors of mmWave systems are blockage (high penetration loss) and deafness (misalignment between the beams of the transmitter and receiver). To alleviate these problems, it is imperative to incorporate efficient association and relaying between terminals and access points. Unfortunately, the existing association techniques are designed for the traditional interference-limited networks, and thus are highly suboptimal for mmWave communications due to narrow-beam operations and the resulting non-negligible interference-free behavior. This paper introduces a distributed approach that solves the joint association and relaying problem in mmWave networks considering the load balancing at access points. The problem is posed as a novel stochastic optimization problem, which is solved by distributed auction algorithms where the clients and relays act asynchronously to achieve optimal client-relay-access point association. It is shown that the algorithms provably converge to a solution that maximizes the aggregate logarithmic utility within a desired bound. Numerical results allow to quantify the performance enhancements introduced by the relays, and the substantial improvements of the network throughput and fairness among the clients by the proposed association method as compared to standard approaches. It is concluded that mmWave communications with proper association and relaying mechanisms can support extremely high data rates, connection reliability, and fairness among the clients.
We study the maximum achievable rate of a two-hop amplified-and-forward (AF) relaying millimeter-wave (mm-wave) system, where two AF relaying schemes, i.e., half-duplex (HD) and full-duplex (FD) are discussed. By considering the two-ray mm-wave channel and the Gaussian-type directional antenna, jointly, the impacts of the beamwidth and the self-interference coefficient on maximum achievable rates are investigated. Results show that, under a sum-power constraint, the rate of FD-AF mm-wave relaying outperforms its HD counterpart only when antennas with narrower beamwidth and smaller self-interfe…
In millimeterWave wireless networks the rapidly varying wireless channels demand fast and dynamic resource allocation mechanisms. This challenge is hereby addressed by a distributed approach that optimally solves the fundamental resource allocation problem of joint client association and relaying. The problem is posed as a multi assignment optimization, for which a novel solution method is established by a series of transformations that lead to a tractable minimum cost flow problem. The method allows to design distributed auction solution algorithms where the clients and relays act asynchronou…
This paper presents a novel stochastic geometry approach to the connectivity of milimeter wave (mmWave) networks with multi-hop relaying. The random positions and shapes of obstacles in the radio environment are modeled as a Boolean model, whose germs are distributed according to a Poisson point process and grains are random rectangles. The derived analytical results shed light on how the connectivity of mmWave networks depends on key system parameters such as the density and size of obstacles as well as relaying route window -- the range of distances in which routing relays are selected. We f…
Millimeter wave channels suffer from considerable degradation in the channel quality when the signal is Non Line of Sight (NLOS) between the source and the destination. Multihop relaying is thus anticipated to improve the communi- cation between a source and its destination. This is achieved by transmitting the signal to a sequence of relays in which a Line of Sight (LOS) signal exists between two nodes along the path, or more generally when the signal is better than the transmitted signal directly from the source to the destination. In this paper, we consider a millimeter wave network compose…
Relaying techniques for millimeter-wave wireless networks represent a powerful solution for improving the transmission performance. In this work, we quantify the benefits in terms of delay and throughput for a random-access multi-user millimeter-wave wireless network, assisted by a full-duplex network cooperative relay. The relay is equipped with a queue for which we analyze the performance characteristics (e.g., arrival rate, service rate, average size, and stability condition). Moreover, we study two possible transmission schemes: fully directional and broadcast. In the former, the source no…
This paper investigates the resource scheduling for heterogeneous vehicular networks, where some moving vehicles are selected and scheduled as helping relays to assist information transmission between the roadside infrastructure and other moving vehicles. For such a system, we propose a mobile-service based max-min fairness resource scheduling scheme, where service amount which is more suitable for high mobility scenarios is adopted to characterize the information transmission capacity of the links and the max-min criteria is adopted to meet the fairness requirement of the moving vehicles. Sim…
Millimeter-wave (mmWave) communication plays a vital role to efficiently disseminate large volumes of data in beyond-5G networks. Unfortunately, the directionality of mmWave communication significantly complicates efficient data dissemination, particularly in multicasting, which is gaining more and more importance in emerging applications (e.g., V2X, public safety). While multicasting for systems operating at lower frequencies (i.e., sub-6GHz) has been extensively studied, they are sub-optimal for mmWave systems as mmWave has significantly different propagation characteristics, i.e., using the…
We present a statistical analysis of a mixed radio-frequency (RF)-visible light communications (VLC) relaying system, where outdoor millimeter wave based RF links are utilized to provide backhaul connectivity for indoor VLC broadcasting. The multiple RF links are assumed to communicate with the VLC access point through decode-and-forward relay. Novel closed-form outage probability and average bit error rate expressions are derived and utilized to obtain numerical results. Monte Carlo simulations validate presented numerical results, which are further used to examine the effects of system and c…
With vast amounts of spectrum available in the millimeter wave (mmWave) band, small cells at mmWave frequencies densely deployed underlying the conventional homogeneous macrocell network have gained considerable interest from academia, industry, and standards bodies. Due to high propagation loss at higher frequencies, mmWave communications are inherently directional, and concurrent transmissions (spatial reuse) under low inter-link interference can be enabled to significantly improve network capacity. On the other hand, mmWave links are easily blocked by obstacles such as human body and furnit…
A new, fair relay selection scheme is proposed for a dual-hop decode-and-forward network with randomly-distributed relays. Most of the reported works in the literature achieve fairness at the expense of degrading the outage probability performance. In addition, they often assume that the number and locations of the relays are known. In contrast, the proposed scheme achieves fairness in a random field of relays without deteriorating the outage probability performance. In this scheme, each relay maintains a countdown timer whose initial value is a function of the relay location and a tunable par…
This paper studies a novel cooperation method in a two-user wireless powered communication network (WPCN), in which one hybrid access point (HAP) broadcasts wireless energy to two distributed wireless devices (WDs), while the WDs use the harvested energy to transmit their independent information to the HAP. To tackle the user unfairness problem caused by the near-far effect in WPCN, we allow the WD with the stronger WD-to-HAP channel to use part of its harvested energy to help relay the other weaker user's information to the HAP. In particular, we exploit the use of backscatter communication d…
Increasing wireless cellular networks capacity is one of the major challenges for the coming years, especially if we consider the annual doubling of mobile user traffic. Towards that and thanks to the fact that a significant amount of mobile data is indeed delay tolerable, in this paper, we suggest embedding the delayed offloading of some user traffic to be a part of future wireless cellular networks. To accomplish this, user delayed files will be offloaded using ultra-high speed Millimeter Wave (Mm-W) Gates. The Mm-W Gate, which will be distributed inside the Macro basestation (BS) area, cons…
Millimeter wave (mmW) bands between 30 and 300 GHz have attracted considerable attention for next-generation cellular networks due to vast quantities of available spectrum and the possibility of very high-dimensional antenna ar-rays. However, a key issue in these systems is range: mmW signals are extremely vulnerable to shadowing and poor high-frequency propagation. Multi-hop relaying is therefore a natural technology for such systems to improve cell range and cell edge rates without the addition of wired access points. This paper studies the problem of scheduling for a simple infrastructure c…
Millimeter wave (mmW) frequencies between 30 and 300 GHz are a new frontier for cellular communication that offers the promise of orders of magnitude greater bandwidths combined with further gains via beamforming and spatial multiplexing from multi-element antenna arrays. This paper surveys measurements and capacity studies to assess this technology with a focus on small cell deployments in urban environments. The conclusions are extremely encouraging; measurements in New York City at 28 and 73 GHz demonstrate that, even in an urban canyon environment, significant non-line-of-sight (NLOS) outd…
Millimeter wave (mmWave) communications have been postulated as one of the most disruptive technologies for future 5G systems. Among mmWave bands the 60-GHz radio technology is specially suited for ultradense small cells and mobile data offloading scenarios. Many challenges remain to be addressed in mmWave communications but among them deafness, or misalignment between transmitter and receivers beams, and interference management lie among the most prominent ones. In the recent years, scenarios considering negligible interference on mmWave resource allocation have been rather common in literatu…
Envisioned for fifth generation (5G) systems, millimeter-wave (mmWave) communications are under very active research worldwide. Although pencil beams with accurate beamtracking may boost the throughput of mmWave systems, this poses great challenges in the design of radio resource allocation for highly mobile users. In this paper, we propose a joint adaptive beam-frequency allocation algorithm that takes into account the position uncertainty inherent to high mobility and/or unstable users as, e.g., Unmanned Aerial Vehicles (UAV), for whom this is a major problem. Our proposed method provides an…
Unmanned aerial vehicles (UAVs) and Terahertz (THz) technology are envisioned to play paramount roles in next-generation wireless communications. In this paper, we present a novel secure UAV-assisted mobile relaying system operating at THz bands for data acquisition from multiple ground user equipments (UEs) towards a destination. We assume that the UAV-mounted relay may act, besides providing relaying services, as a potential eavesdropper called the untrusted UAV-relay (UUR). To safeguard end-to-end communications, we present a secure two-phase transmission strategy with cooperative jamming. …
Limited backhaul bandwidth and blockage effects are two main factors limiting the practical deployment of millimeter wave (mmWave) networks. To tackle these issues, we study the feasibility of relaying as well as caching in mmWave networks. A user association and relaying (UAR) criterion dependent on both caching status and maximum biased received power is proposed by considering the spatial correlation caused by the coexistence of base stations (BSs) and relay nodes (RNs). A joint UAR and caching placement problem is then formulated to maximize the backhaul offloading traffic. Using stochasti…
We integrate a wireless powered communication network with a cooperative cognitive radio network, where multiple secondary users (SUs) powered wirelessly by a hybrid access point (HAP) help a primary user relay the data. As a reward for the cooperation, the secondary network gains the spectrum access where SUs transmit to HAP using time division multiple access. To maximize the sum-throughput of SUs, we present a secondary sum-throughput optimal resource allocation (STORA) scheme. Under the constraint of meeting target primary rate, the STORA scheme chooses the optimal set of relaying SUs and …
With the incoming 5G network, the ubiquitous Internet of Things (IoT) devices can benefit our daily life, such as smart cameras, drones, etc. With the introduction of the millimeter-wave band and the thriving number of IoT devices, it is critical to design new dynamic spectrum access (DSA) system to coordinate the spectrum allocation across massive devices in 5G. In this paper, we present Hermes, the first decentralized DSA system for massive devices deployment. Specifically, we propose an efficient multi-agent reinforcement learning algorithm and introduce a novel shuffle mechanism, addressin…
Millimeter wave (mmWave) will play a significant role as a 5G candidate in facing the growing demand of enormous data rate in the near future. The conventional mmWave standard, IEEE 802.11ad, considers establishing only one mmWave link in wireless local area network (WLAN) to provide multi Gbps data rate. But, mmWave has a tenuous channel which hinders it from providing such rate. Hence, it's necessary to establish multiple mmWave links simultaneously by deploying a multiple number of mmWave access points (APs) in 5G networks. Unfortunately, applying conventional standard without any modificat…
Millimeter wave (mmWave) communication has recently attracted significant attention from both industrial and academic communities. The large bandwidth availability as well as low interference nature of mmWave spectrum is particularly attractive for industrial communication. However, inherent challenges such as coverage and blockage of mmWave communication cause highly fluctuated channel quality. This paper explores wireless medium access control (MAC) schedulers for mmWave-based industrial wireless applications. Our objective is to design a high-performance and enhanced fairness MAC scheduling…
The use of unmanned aerial vehicle (UAV)-based communication in millimeter-wave (mmWave) frequencies to provide on-demand radio access is a promising approach to improve capacity and coverage in beyond-5G (B5G) systems. There are several design aspects to be addressed when optimizing for the deployment of such UAV base stations. As traffic demand of mobile users varies across time and space, dynamic algorithms that correspondingly adjust the UAV locations are essential to maximize performance. In addition to careful tracking of spatio-temporal user/traffic activity, such optimization needs to …
We propose an effective interference management and beamforming mechanism for uplink communication systems that yields fair allocation of rates. In particular, we consider a hotspot area of a millimeter-wave (mmWave) access network consisting of multiple user equipment (UE) in the uplink and multiple access points (APs) with directional antennas and adjustable beam widths and directions (beam configurations). This network suffers tremendously from multi-beam multi-user interference, and, to improve the uplink transmission performance, we propose a centralized scheme that optimizes the power, t…
We consider a dynamic millimeter-wave network with integrated access and backhaul, where mobile relay nodes move to auto-reconfigure the wireless backhaul. Specifically, we focus on in-band relaying networks, which conduct access and backhaul links on the same frequency band with severe constraints on co-channel interference. In this context, we jointly study the complex problem of dynamic relay node positioning, user association, and backhaul capacity allocation. To address this problem, with limited complexity, we adopt a hierarchical multi-agent reinforcement with a two-level structure. A h…
Wireless backhauling at millimeter-wave frequencies (mmWave) in static scenarios is a well-established practice in cellular networks. However, highly directional and adaptive beamforming in today's mmWave systems have opened new possibilities for self-backhauling. Tapping into this potential, 3GPP has standardized Integrated Access and Backhaul (IAB) allowing the same base station serve both access and backhaul traffic. Although much more cost-effective and flexible, resource allocation and path selection in IAB mmWave networks is a formidable task. To date, prior works have addressed this cha…
In this paper, we consider the multi-user scheduling problem in millimeter wave (mmWave) video streaming networks, which comprise a streaming server and several users, each requesting a video stream with a different resolution. The main objective is to optimize the long-term average quality of experience (QoE) for all users. We tackle this problem by considering the physical layer characteristics of the mmWave network, including the beam alignment overhead due to pencil-beams. To develop an efficient scheduling policy, we leverage the contextual multi-armed bandit (MAB) models to propose a bea…
The millimeter wave (mmWave) communication has drawn intensive attention with abundant band resources. In this paper, we consider the popular content distribution (PCD) problem in the mmWave vehicular network. In order to offload the communication burden of base stations (BSs), vehicle-to-vehicle (V2V) communication is introduced into the PCD problem to transmit contents between on-board units (OBUs) and improve the transmission efficiency. We propose a full-duplex (FD) cooperative scheme based on coalition formation game, and the utility function is provided based on the maximization of the n…
The small cells in millimeter wave (mmWave) have been utilized extensively for the fifth generation (5G) mobile networks. And full-duplex (FD) communications become possible with the development of self-interference (SI) cancellation technology. In this paper, we focus on the optimal allocation of the sub-channels in the small cells deployed densely underlying the mmWave networks. In order to improve the resource utilization and network capacity, device-to-device (D2D) communications are adopted in networks. For maximizing the system throughput, we propose a cooperative sub-channel allocation …
Unmanned aerial vehicle (UAV) has recently attracted a lot of attention as a candidate to meet the 6G ubiquitous connectivity demand and boost the resiliency of terrestrial networks. Thanks to the high spectral efficiency and low latency, non-orthogonal multiple access (NOMA) is a potential access technique for future communication networks. In this paper, we propose to use the UAV as a moving base station (BS) to serve multiple users using NOMA and jointly solve for the 3D-UAV placement and resource allocation problem. Since the corresponding optimization problem is non-convex, we rely on the…
Wireless x-haul networks rely on microwave and millimeter-wave links between 4G and/or 5G base-stations to support ultra-high data rate and ultra-low latency. A major challenge associated with these high frequency links is their susceptibility to weather conditions. In particular, precipitation may cause severe signal attenuation, which significantly degrades the network performance. In this paper, we develop a Predictive Network Reconfiguration (PNR) framework that uses historical data to predict the future condition of each link and then prepares the network ahead of time for imminent distur…
