To make full use of photocathode material and improve its quantum efficiency lifetime, it can be necessary to operate laser away from the cathode center in photoinjectors. In RF guns, the off-axis emitted beam will see a time-dependent RF effect, which would generate a significant growth in transverse emittance. It has been demonstrated that such an emittance growth can be almost completely compensated by orienting the beam on a proper orbit in the downstream RF cavities along the injector. In this paper we analyze in detail the simulation techniques used in reference[1] and the issues associated with them. The optimization of photoinjector systems involving off-axis beams is a challenging problem. To solve this problem, one needs advanced simulation tools including both genetic algorithms and an efficient algorithm for 3D space charge. In this paper, we report on simulation studies where the two codes ASTRA and IMPACT-T are used jointly to overcome these challenges, in order to optimize a system designed to compensate for the emittance growth in a beam emitted off axis.
Next generation accelerators will require a high current, low emittance beam with a low energy spread. Such accelerators will employ advanced beam conditioning systems such as emittance exchangers to manipulate high brightness beams. One of the goals of the Fermilab A0 photoinjector is to investigate the transverse to longitudinal emittance exchange principle. Coherent synchrotron radiation could limit high current operation of the emittance exchanger. In this paper, we report on the preliminary experimental and simulation study of the coherent synchroton radiation (CSR) in the emittance excha…
We present the results of transverse emittance and longitudinal current profile measurements of high bunch charge (greater than or equal to 100 pC) beams produced in the DC gun-based Cornell Energy Recovery Linac Photoinjector. In particular, we show that the cathode thermal and core beam emittances dominate the final 95% and core emittance measured at 9-9.5 MeV. Additionally, we demonstrate excellent agreement between optimized 3D space charge simulations and measurement, and show that the quality of the transverse laser distribution limits the optimal simulated and measured emittances. These…
Reducing the intrinsic emittance of photocathodes is one of the most promising routes to improving the brightness of electron sources. However, when emittance growth occurs during beam transport (for example, due to space-charge), it is possible that this emittance growth overwhelms the contribution of the photocathode and, thus, in this case source emittance improvements are not beneficial. Using multi-objective genetic optimization, we investigate the role intrinsic emittance plays in determining the final emittance of several space-charge dominated photoinjectors, including those for high r…
In state of the art photoinjector electron sources, thermal emittance from photoemission dominates the final injector emittance. Therefore, low thermal emittance cathode developments and diagnostics are very important. Conventional thermal emittance measurements for the high gradient gun are time-consuming and thus thermal emittance is not measured as frequently as quantum efficiency during the lifetime of photocathodes, although both are important properties for the photoinjector optimizations. In this paper, a single shot measurement of photoemission transverse momentum, i.e., thermal emitta…
Thermal emittance and quantum efficiency (QE) are key figures of merit of photocathodes, and their uniformity is critical to high-performance photoinjectors. Several QE mapping technologies have been successfully developed; however, there is still a dearth of information on thermal emittance maps. This is because of the extremely time-consuming procedure to gather measurements by scanning a small beam across the cathode with fine steps. To simplify the mapping procedure, and to reduce the time required to take measurements, we propose a new method that requires only a single scan of the soleno…
Photoinjectors are the main high brightness electron sources for X-ray free electron lasers (XFEL). Photoinjector emittance reduction is one of the key knobs for improving XFEL lasing, so precise emittance measurement is critical. It's well known that rms emittance is very sensitive to low intensity tails of particle distributions in the phase space, whose measurement depend on the signal to noise ratio (SNR) and image processing procedures. Such sensitivities make the interpretations of beam transverse brightness challenging, leading to different emittance definitions to reduce the impact of …
The solenoid scan is one of the most common methods for the in-situ measurement of the thermal emittance of a photocathode in an rf photoinjector. The fringe field of the solenoid overlaps with the gun rf field in quite a number of photoinjectors, which makes accurate knowledge of the transfer matrix challenging, thus increases the measurement uncertainty of the thermal emittance. This paper summarizes two methods that have been used to solve the overlap issue and explains their deficiencies. Furthermore, we provide a new method to eliminate the measurement error due to the overlap issue in so…
The possibility of using electron beam phase space manipulations to support a free-electron laser accelerator design optimization has motivated our research. An on-going program demonstrating the exchange of transverse horizontal and longitudinal emittances at the Fermilab A0 photoinjector has benefited recently from the upgrade of several of the key diagnostics stations. Accurate measurements of these properties upstream and downstream of the exchanger beamline are needed. Improvements in the screen resolution term and reduced impact of the optical system's depth-of-focus by using YAG:Ce sing…
In this paper, we present a detailed analysis of the effects of quadrupole components in radiofrequency (RF) photoinjectors, which could occur either in the RF cavity or in the gun solenoid, and their compensation using a skew quadrupole corrector. The analysis is generalized to the case in which the correction cannot be applied at the same location as the quadrupole. A practical guide to setting the corrector to eliminate correlation in the x-y space is discussed. Particle tracking simulations and measurements of emittance and beam matrix elements obtained at the UCLA Pegasus photoinjector ar…
The production of electron bunches with low transverse emittance approaches the thermal emittance of the photocathode as various aberrations are corrected. Recently, the coupled transverse dynamics aberration was theoretically identified as a significant source of emittance growth and a corrector magnet was proposed for its elimination [D.H. Dowell, F. Zhou, and J. Schmerge, PRAB 21, 010101 (2018)]. This aberration arises when the beam acquires an asymmetric distribution that is then rotated with respect to the transverse reference axis thus introducing a correlation in the vertical and horizo…
At the Fermilab A0 photoinjector facility, bunch-length measurements of the laser micropulse and the e-beam micropulse have been done in the past with a fast single-sweep module of the Hamamatsu C5680 streak camera with an intrinsic shot-to-shot trigger jitter of 10-20ps. We have upgraded the camera system with the synchroscan module tuned to 81.25MHz to provide synchronous summing capability with less than 1.5ps FWHM trigger jitter and a phase-locked delay box to provide phase stability of ~1ps over 10s of minutes. These steps allowed us to measure both the UV laser pulse train at 263nm and t…
The multiplexing capabilities of superconducting X-ray free-electron lasers (FELs) have gained much attention in recent years. The demanding requirements for photon properties from multiple undulator lines necessitate more flexible beam manipulation techniques to achieve the goal of "beam on demand". In this paper, we investigate a multiplexed configuration for the photoinjector of high-repetition-rate FELs that aims to simultaneously provide low-emittance electron beams of different charges. A parallel, multi-objective genetic algorithm is implemented for the photoinjector parameter optimizat…
In this paper, we propose a masked photocathode inside a photoinjector for generating high brightness electron beam. Instead of mounting the photocathode onto an electrode, an electrode with small hole is used as a mask to shield the photocathode from the accelerating vacuum chamber. Using such a masked photocathode will make the replacement of photocathode material easy by rotating the photocathode behind the electrode into the hole. Furthermore, this helps reduce the dark current or secondary electron emission from the photocathode material. The masked photocathode also provides transverse c…
We report an unusual regime of emittance self-compensation in an electron bunch generated in blow-out mode by a radio-frequency photocathode gun. Simulations clearly show an initial growth and a subsequent self-compensation of projected emittance in a divergent electron bunch originating from the effects of: (i) strong space-charge forces of mirror charges on the cathode, (ii) an energy chirp in the bunch and (iii) substantial re-shaping of the electron bunch. Furthermore, we show analytically and numerically how a complex interplay between these effects leads to emittance self-compensation in…
SHINE, as the first hard x-ray free-electron-laser (FEL) facility in China, is designed to provide high-brightness FEL lasing under high-repetition-rate operation mode. In order to drive x-ray FEL pulses with high qualities, the photoinjector section is deployed to provide the specified electron beam with low transverse emittance and high brightness. Normally the multi-objective optimization algorithm is employed in the injector beam dynamics design. In this paper, the many-objective optimization algorithm NSGA-III is introduced to the injector physical design for optimizing the 4 beam quality…
Ultralow emittance ($\leq20$ nm, normalized) electron beams with $10^5$ electrons per bunch are obtained by tightly focusing an ultrafast ($\sim$ 100 fs) laser pulse on the cathode of a 1.6 cell radiofrequency photoinjector. Taking advantage of the small initial longitudinal emittance, a downstream velocity bunching cavity is used to compress the beam to $<10$ fs rms bunch length. The measurement is performed using a thick high voltage deflecting cavity which is shown to be well-suited to measure ultrashort durations of bunching beams, provided that the beam reaches a ballistic longitudinal fo…
Recent studies of the performance of radio-frequency (RF) copper cavities operated at cryogenic temperatures have shown a dramatic increase in the maximum achievable surface electric field. We propose to exploit this development to enable a new generation of photoinjectors operated at cryogenic temperatures that may attain, through enhancement of the launch field at the photocathode, a significant increase in five-dimensional electron beam brightness. We present detailed studies of the beam dynamics associated with such a system, by examining an S-band photoinjector operated at 250 MV/m peak e…
Classical and quantum beam dynamics simulation of the RF photoinjector test bench
ITMO University（ITMO大学）；Joint Institute for Nuclear Research（联合核研究所）；Budker Institute of Nuclear Physics, Siberian Branch of RAS（俄罗斯科学院西伯利亚分院布德KER核物理研究所）；Institute of Nuclear Physics（核物理研究所）
A comparison of the two most prominent electron sources of high average current high brightness electron beams, DC and superconducting RF photoemission guns, is carried out using a large-scale multivariate genetic optimizer interfaced with space charge simulation codes. The gun geometry for each case is varied concurrently with laser pulse shape and parameters of the downstream beamline elements of the photoinjector to obtain minimum emittance as a function of bunch charge. Realistic constraints are imposed on maximum field values for the two gun types. The SRF and DC gun emittances and beam e…
Motivated by the emittance requirements for future light sources, we show how longitudinal-transverse correlations can be introduced to create beams with large emittance asymmetry. This concept generalizes a key aspect of a Flat Beam Transform, which introduces initial correlations among the transverse planes, to systems with initial longitudinal-transverse correlations. We present an eigen-emittance formalism to analyze such systems. We illustrate the approach by analyzing an electron beam emitted from a photoinjector utilizing a laser with a tilted pulse front. This approach can be used to d…
A crucial part of the design of an FCC-ee detector is the minimisation of the disruption of the beam due to the presence of a large and powerful detector magnet. Indeed, the emittance blow-up of the few meters around the interaction point (IP) at lower energies is comparable to the emittance introduced by the rest of the 100 km ring. Vertical emittance is the single most important factor in achieving high performance (luminosity, in this case) in a modern e^+ e^- storage ring such as the FCC-ee. The design adopted is the simplest possible arrangement that can nevertheless deliver high performa…
Since the introduction of the radio-frequency (rf) photoinjector electron source over thirty years ago, peak performance demands have dictated the use of high accelerating electric fields. With recent strong advances in obtainable field values, attendant increases in beam brightness are expected to be dramatic. In this article, we examine the implementation of very high gradient acceleration in a high frequency, cryogenic rf photoinjector. We discuss in detail the effects of introducing, through an optimized rf cavity shape, rich spatial harmonic content in the accelerating modes in this devic…
Flat beams -- beams with asymmetric transverse emittances -- have important applications in novel light-source concepts, advanced-acceleration schemes and could possibly alleviate the need for damping rings in lepton colliders. Over the last decade, a flat-beam-generation technique based on the conversion of an angular-momentum-dominated beam was proposed and experimentally tested. In this paper we explore the production of compressed flat beams. We especially investigate and optimize the flat-beam transformation for beams with substantial fractional energy spread. We use as a simulation examp…
Recent successful lasing of the Linac Coherent Light Source (LCLS) in the hard x-ray regime and the experimental demonstration of a possibility to produce low-charge bunches with ultra-small normalized emittance have lead to the discussions on optimistic scenarios of operation of the European XFEL. In this paper we consider new options that make use of low-emittance beams, a relatively high beam energy, tunable-gap undulators, and a multi-bunch capability of this facility. We study the possibility of operation of a spontaneous radiator (combining two of them, U1 and U2, in one beamline) in the…
Nonlinear Photoemission for Bright Beams in X-Band Photoinjectors
Biodesign Institute, Arizona State University（亚利桑那州立大学生物设计学院）；Department of Physics, Arizona State University（亚利桑那州立大学物理系）；Center for Applied Structural Discovery, Arizona State University（亚利桑那州立大学应用结构发现中心）
Advances in electron beam technology have been central to creating the current generation of x-ray free electron lasers and ultra-fast electron microscopes. These once exotic devices have become essential tools for basic research and applied science. One important beam technology for both is the electron source which, for many of these instruments, is the photocathode gun. The invention of the photocathode gun and the concepts of emittance compensation and beam matching in the presence of space charge and RF forces have made these high-quality beams possible. Achieving even brighter beams requ…
At the Fermilab Tevatron collider, we studied the feasibility of suppressing the antiproton head-on beam-beam tune spread using a magnetically confined 5-keV electron beam with Gaussian transverse profile overlapping with the circulating beam. When electron cooling of antiprotons was applied in regular Tevatron operations, the nonlinear head-on beam-beam effect on antiprotons was small. Therefore, we first focused on the operational aspects, such as beam alignment and stability, and on fundamental observations of tune shifts, tune spreads, lifetimes, and emittances. We also attempted two speci…
Project-X is the proposed high intensity proton facility to be built at Fermilab, US. First stage of the Project-X consists of superconducting linac which will be operated in continuous wave (CW) mode to accelerate the beam from 2.5 MeV to 3 GeV. The operation at CW mode puts high tolerances on the beam line components, particularly on radiofrequency (RF) cavity. The failure of beam line elements at low energy is very critical as it results in mis-match of the beam with the following sections due to different beam parameters than designed parameter. It makes the beam unstable which causes emit…
High quality electron beams with flat distributions in both energy and current are critical for many accelerator-based scientific facilities such as free-electron lasers and MeV ultrafast electron diffraction and microscopes. In this Letter we report on using corrugated structures to compensate for the beam nonlinear energy chirp imprinted by the curvature of the radio-frequency field, leading to a significant reduction in beam energy spread. By using a pair of corrugated structures with orthogonal orientations, we show that the quadrupole wake fields which otherwise increase beam emittance ca…
The superconducting upgrade of the REX-ISOLDE radioactive ion beam (RIB) post-accelerator at CERN will utilise a compact lattice comprising quarter-wave resonators (QWRs) and solenoids, accelerating beams in the mass range 2.5 < A/q < 4.5 to over 10 MeV/u. The short and independently phased quarter-wave structures allow for the acceleration of RIBs over a variable velocity profile and provide an unrivalled longitudinal acceptance when coupled with solenoid focusing. The incorporation of the solenoids into the cryomodule shortens the linac, whilst maximising the acceptance, but the application …
A detailed experimental and simulation study of the extraction of a 24 keV He-ion beam from an ECR ion source and the subsequent beam transport through an analyzing magnet is presented. We find that such a slow ion beam is very sensitive to space-charge forces, but also that the neutralization of the beam's space charge by secondary electrons is virtually complete for beam currents up to at least 0.5 mA. The beam emittance directly behind the extraction system is 65 pi mm mrad and is determined by the fact that the ion beam is extracted in the strong magnetic fringe field of the ion source. Th…
A highly efficient, fully parallelized, six-dimensional tracking model for simulating interactions of colliding hadron beams in high energy ring colliders and simulating schemes for mitigating their effects is described. The model uses the weak-strong approximation for calculating the head-on interactions when the test beam has lower intensity than the other beam, a look-up table for the efficient calculation of long-range beam-beam forces, and a self-consistent Poisson solver when both beams have comparable intensities. A performance test of the model in a parallel environment is presented. T…
