We construct an ensemble distribution to describe steady immiscible two-phase flow of two incompressible fluids in a porous medium. The system is found to be ergodic. The distribution is used to compute macroscopic flow parameters. In particular, we find an expression for the overall mobility of the system from the ensemble distribution. The entropy production at the scale of the porous medium is shown to give the expected product of the average flow and its driving force, obtained from a black-box description. We test numerically some of the central theoretical results.
We demonstrate through numerical simulations and a mean field calculation that immiscible two-phase flow in a porous medium behaves effectively as a Bingham viscoplastic fluid. This leads to a generalized Darcy equation where the volumetric flow rate depends quadratically on an excess pressure difference in the range of flow rates where the capillary forces compete with the viscous forces. At higher rates, the flow is Newtonian.
Based on non-equilibrium thermodynamics we derive a set of general equations relating the partial volumetric flow rates to each other and to the total volumetric flow rate in immiscible two-phase flow in porous media. These equations together with the conservation of saturation reduces the immiscible two-phase flow problem to a single-phase flow problem of a complex fluid. We discuss the new equation in terms of the relative permeability equations. We test the equations on model systems, both analytically and numerically.
We present a theoretical framework for immiscible incompressible two-phase flow in homogeneous porous media that connects the distribution of local fluid velocities to the average seepage velocities. By dividing the pore area along a cross-section transversal to the average flow direction up into differential areas associated with the local flow velocities, we construct a distribution function that allows us not only to re-establish existing relationships between the seepage velocities of the immiscible fluids, but also to find new relations between their higher moments. We support and demonst…
Based on thermodynamic considerations we derive a set of equations relating the seepage velocities of the fluid components in immiscible and incompressible two-phase flow in porous media. They necessitate the introduction of a new velocity function, the co-moving velocity. This velocity function is a characteristic of the porous medium. Together with a constitutive relation between the velocities and the driving forces, such as the pressure gradient, these equations form a closed set. We solve four versions of the capillary tube model analytically using this theory. We test the theory numerica…
We present a Markov Chain Monte Carlo algorithm based on the Metropolis algorithm for simulation of the flow of two immiscible fluids in a porous medium under macroscopic steady-state conditions using a dynamical pore network model that tracks the motion of the fluid interfaces. The Monte Carlo algorithm is based on the configuration probability, where a configuration is defined by the positions of all fluid interfaces. We show that the configuration probability is proportional to the inverse of the flow rate. Using a two-dimensional network, advancing the interfaces using time integration the…
A fundamental variable characterizing immiscible two-phase flow in porous media is the wetting saturation, which is the ratio between the pore volume filled with wetting fluid and the total pore volume. More generally, this variable comes from a specific choice of coordinates on some underlying space, the domain of variables that can be used to express the volumetric flow rate. The underlying mathematical structure allows for the introduction of other variables containing the same information, but which are more convenient from a theoretical point of view. We introduce along these lines polar …
When two immiscible liquids that coexist inside a porous medium are drained through an opening, a complex flow takes place in which the interface between the liquids moves, tilts and bends. The interface profiles depend on the physical properties of the liquids and on the velocity at which they are extracted. If the drainage flow rate, the liquids volume fraction in the drainage flow and the physical properties of the liquids are known, the interface angle in the immediate vicinity of the outlet (theta) can be determined. In this work, we define four nondimensional parameters that rule the flu…
We present a continuum (i.e., an effective) description of immiscible two-phase flow in porous media characterized by two fields, the pressure and the saturation. Gradients in these two fields are the driving forces that move the immiscible fluids around. The fluids are characterized by two seepage velocity fields, one for each fluid. Following Hansen et al.\ (Transport in Porous Media, 125, 565 (2018)), we construct a two-way transformation between the velocity couple consisting of the seepage velocity of each fluid, to a velocity couple consisting of the average seepage velocity of both flui…
We present in detail a set of algorithms to carry out fluid displacements in a dynamic pore-network model of immiscible two-phase flow in porous media. The algorithms are general and applicable to regular and irregular pore networks in two and three dimensions with different boundary conditions. Implementing these sets of algorithms, we describe a dynamic pore-network model and reproduce some of the fundamental properties of both the transient and steady-state two-phase flow. During drainage displacements, we show that the model can reproduce the flow patterns corresponding to viscous fingerin…
Immiscible fluid displacement in porous media is fundamental for many environmental processes, including infiltration of water in soils, groundwater remediation, enhanced recovery of hydrocarbons and carbon geosequestration. Microstructural heterogeneity, in particular of particle sizes, can significantly impact immiscible displacement. For instance, it may lead to unstable flow and preferential displacement patterns. We present a systematic, quantitative pore-scale study of the impact of spatial correlations in particle sizes on the drainage of a partially-wetting fluid. We perform pore-netwo…
We construct a statistical mechanics for immiscible and incompressible two-phase flow in porous media under local steady-state conditions based on the Jaynes maximum entropy principle. A cluster entropy is assigned to our lack of knowledge of, and control over, the fluid and flow configurations in the pore space. As a consequence, two new variables describing the flow emerge: The agiture, that describes the level of agitation of the two fluids, and the flow derivative which is conjugate to the saturation. Agiture and flow derivative are the analogs of temperature and chemical potential in stan…
Colloidal particles hold promise for mobilizing and removing trapped immiscible fluids from porous media, with implications for key energy and water applications. Most studies focus on accomplishing this goal using particles that can localize at the immiscible fluid interface. Therefore, researchers typically seek to optimize the surface activity of particles, as well as their ability to freely move through a pore space with minimal deposition onto the surrounding solid matrix. Here, we demonstrate that deposition can, surprisingly, promote mobilization of a trapped fluid from a porous medium …
Immiscible fluid displacement in porous media occurs in several natural and industrial processes. For example, during petroleum extraction from porous rock reservoirs, water is used to displace oil. In this paper, we investigate primary drainage and imbibition in a heterogeneous porous medium using an improved numerical model based on the multicomponent pseudopotential lattice Boltzmann method. We apply recent developments from the literature and develop new pressure boundary conditions. We show that the proposed model is able to simulate realistic viscosity ratios, and it allows independent t…
Immiscible two-phase flow in porous media with mixed wet conditions was examined using a capillary fiber bundle model, which is analytically solvable, and a dynamic pore network model. The mixed wettability was implemented in the models by allowing each tube or link to have a different wetting angle chosen randomly from a given distribution. Both models showed that mixed wettability can have significant influence on the rheology in terms of the dependence of the global volumetric flow rate on the global pressure drop. In the capillary fiber bundle model, for small pressure drops when only a sm…
The change in contact angles due to the injection of low salinity water or any other wettability altering agent in an oil-rich porous medium is modeled by a network model of disordered pores transporting two immiscible fluids. We introduce a dynamic wettability altering mechanism, where the time dependent wetting property of each pore is determined by the cumulative flow of water through it. Simulations are performed to reach steady-state for different possible alterations in the wetting angle ($θ$). We find that deviation from oil-wet conditions re-mobilizes the stuck clusters and increases t…
The Saffman-Taylor instability occurs when { a} Stokes fluid is displaced by a less viscous one { in} a Hele-Shaw cell. { This model is useful to study the secondary oil recovery from a pororus medum.} Since 1960, { polymer solutions} were used as displacing fluids; moreover, the oil in a porous reservoir can often be considered a non-Newtonian fluid. Motivated by this fact, in this paper we study the linear stability of the displacement of two Oldroyd-B fluids in a rectilinear Hele-Shaw cell, even if the direct relevance for the flow through porous media is not so evident. We get an { approxi…
This document is a presentation of the equations of simultaneous water and oil flow in deformable porous medium and linear poromechanics as well as the staggered solution algorithm to solve the coupled system of equations.
Using thermodynamic and variational principles we examine a basic phase field model for a mixture of two incompressible fluids in strongly perforated domains. With the help of the multiple scale method with drift and our recently introduced splitting strategy for Ginzburg-Landau/Cahn-Hilliard-type equations [Schmuck et al., Proc. R. Soc. A 468:3705-3724, 2012.], we rigorously derive an effective macroscopic phase field formulation under the assumption of periodic flow and a sufficiently large Péclet number. As for classical convection-diffusion problems, we obtain systematically diffusion-disp…
Immiscible fluids flowing at high capillary numbers in porous media may be characterized by an effective viscosity. We demonstrate that the effective viscosity is well described by the Lichtenecker-Rother equation. The exponent $α$ in this equation takes either the value 1 or 0.6 in two- and 0.5 in three-dimensional systems depending on the pore geometry. Our arguments are based on analytical and numerical methods.
We compute the fluid flow time-correlation functions of incompressible, immiscible two-phase flow in porous media using a 2D network model. Given a properly chosen representative elementary volume, the flow rate distributions are Gaussian and the integrals of time correlation functions of the flows are found to converge to a finite value. The integrated cross-correlations become symmetric, obeying Onsager's reciprocal relations. These findings support the proposal of a non-equilibrium thermodynamic description for two-phase flow in porous media.
We study the displacement of three immiscible Stokes fluids with constant viscosities in a porous medium. The middle-layer fluid is contained in a bounded region. We give an analysis of the linear stability of this process. This stability problem has no solution (in general).
We present the visual analysis of our novel parameter study of porous media experiments, focusing on gaining a better understanding of drainage processes on the micro-scale. We analyze the temporal evolution of extracted characteristic values, and discuss how to directly compare experiments that exhibit processes at different temporal scales due to varying boundary and physical conditions. To enable spatio-temporal analysis, we introduce a new abstract visual representation showing which paths through the porous media were occupied to what extent, e.g., allowing for classification into viscous…
We derive the entropy production for transport of multi-phase fluids in a non-deformable, porous medium exposed to differences in pressure, temperature, and chemical potentials. Thermodynamic extensive variables on the macro-scale are obtained by integrating over a representative elementary volume (REV). Using Euler homogeneity of the first order, we obtain the Gibbs equation for the REV. From this we define the intensive variables, the temperature, pressure and chemical potentials and, using the balance equations, derive the entropy production for the REV. The entropy production defines sets …
The paper deals with the global Kondaurov double porosity model describing a non-equilibrium two-phase immiscible flow in fractured-porous reservoirs when non-equilibrium phenomena occur in the matrix blocks, only. It is shown that the homogenized model can be represented as usual equations of two-phase incompressible immiscible flow, except for the addition of two source terms calculated by a solution to a local problem which is a boundary value problem for a non-equilibrium imbibition equation given in terms of the real saturation and a non-equilibrium parameter.
The flow of immiscible fluids inside a porous medium shows non-linearity in the form of a power law in the rheological properties of the fluids under steady state flow conditions. However, different experimental and numerical studies have reported different values for the exponent related to this power law. Here we explore how the rheological properties of the two-phase flow in porous media depends on the distribution of the pore sizes and how it affects the power-law exponent. The pore-size distribution controls fluctuation in the pore radii and their density in a porous material. We present …
In the above paper the authors treat the natural convection boundary layer flow in a Darcy-Brinkman-Forchheimer porous medium. In the energy equation the radiation effect has been taken into account. A two-parameter perturbation method is used for the solution of the equations. The first order results are presented in tables and figures. This is an interesting work but there are some weak points which are presented below:
It is well known that the transient behavior during drainage or imbibition in multiphase flow in porous media strongly depends on the history and initial condition of the system. However, when the steady-state regime is reached and both drainage and imbibition take place at the pore level, the influence of the evolution history and initial preparation is an open question. Here, we present an extensive experimental and numerical work investigating the history dependence of simultaneous steady-state two-phase flow through porous media. Our experimental system consists of a Hele-Shaw cell filled …
Porous materials are used in many fields, including energy industry, agriculture, medical industry, etc. The generation of digital porous media facilitates the fabrication of real porous media and the analysis of their properties. The past random digital porous media generation methods are unable to generate a porous medium with a specific permeability. A new method is proposed in the present study, which can generate the random packed isotropic porous media with specific porosity and permeability. Firstly, the process of generating the random packed isotropic porous media is detailed. Secondl…
Comment on "Scalings of Rayleigh-Taylor Instability at Large Viscosity Contrasts in Porous Media" (N. Sabet, H. Hassanzadeh, A. De Wit, and J. Abedi (2021) Phys. Rev. Lett. 126:094501).
The flow of a gas through porous medium is considered in the case of pressure dependent permeability. Approximate self-similar solutions of the boundary-value problems are found.
Multiphase flow in porous media occurs in several disciplines including petroleum reservoir engineering, petroleum systems' analysis, and CO$_2$ sequestration. While simulations often use a fully implicit discretization to increase the time step size, restrictions on the time step often exist due to non-convergence of the nonlinear solver (e.g. Newton's method). Here this problem is addressed for the Buckley-Leverett equations, which model incompressible, immiscible, two-phase flow with no capillary potential. The equations are recast as a gradient flow using the phase-field method, and a conv…
Convection heat transfer in porous media is a universal phenomenon in nature, and it is also frequently encountered in scientific and engineering fields. An in-depth understanding of the fundamental mechanism of convection heat transfer in porous media requires efficient and powerful numerical tools. In this paper, a cascaded lattice Boltzmann (CLB) method for convection heat transfer in porous media at the representative elementary volume (REV) scale is presented. In the CLB method, the flow field is solved by an isothermal CLB model with the D2Q9 lattice based on the generalized non-Darcy mo…
The coefficients of dispersion, D_{ij}, and the dispersivity, a_{ijkl}, appear in the expression for the flux of a solute in saturated flow through porous media. We present a detailed analysis of these tensors in an axially symmetric porous medium and show that in such a medium, the dispersivity is governed by 6 independent moduli. We present also the constraints that have to be satisfied by these moduli. We also show that at least two independent experiments are required in order to obtain the values of these coefficients for any three-dimensional porous medium domain.
Steady laminar flows through porous media spontaneously generate Lagrangian chaos at pore scale, with qualitative implications for a range of transport, reactive and biological processes. The characterization and understanding of mixing dynamics in these opaque environments is an outstanding challenge. We address this issue by developing a novel technique based upon high-resolution imaging of the scalar signature produced by push-pull flows through porous media samples. Owing to the rapid decorrelation of particle trajectories in chaotic flows, the scalar image measured outside the porous mate…
Given their capability of spreading active chemical species and collecting electricity, porous media made of carbon fibers are extensively used as diffusion layers in energy storage systems, such as redox flow batteries. In spite of this, the dispersion dynamics of species inside porous media is still not well understood and often lends itself to different interpretations. Actually, the microscopic design of efficient porous media which can potentially and effectively improve the performances of flow batteries, is a still open challenge. The present study aims to investigate the effect of fibr…
In this work we show the application of Sailfish to the study of fluid dynamics in porous media. Sailfish is an open-source software based on the lattice-Boltzmann method. This application of computational fluid dynamics is of particular interest to the oil and gas industry and the subject could be a starting point for an undergraduate or graduate student in physics or engineering. We built artificial samples of porous media with different porosities and used Sailfish to simulate the fluid flow through in order to calculate permeability and tortuosity. We also present a simple way to obtain th…
Upscaling the effect of heterogeneities in porous media is crucial for macroscopic flow predictions, with widespread applications in energy and environmental settings. In this study, we derive expressions for the upscaled flow properties of a porous medium with a vertical heterogeneity, using a combination of asymptotic analysis and numerical simulations. Then, we use these upscaled expressions to describe the dynamic flooding of an aquifer, where the classic Buckley-Leverett formulation is modified to account for heterogeneities. In particular, we show that heterogeneities can modify flooding…
Numerical modeling of the migration of three-phase immiscible fluid flow in variably saturated zones is challenging due to the different behavior of the system between unsaturated and saturated zones. This behavior results in the use of different numerical methods for the numerical simulation of the fluid flow depending on whether it is in the unsaturated or saturated zones. This paper shows that using a high-resolution shock-capturing conservative method to resolve the nonlinear governing coupled partial differential equations of a three-phase immiscible fluid flow allows the numerical simula…
We use confocal microscopy to directly visualize the spatial fluctuations in fluid flow through a three-dimensional porous medium. We find that the velocity magnitudes and the velocity components both along and transverse to the imposed flow direction are exponentially distributed, even with residual trapping of a second immiscible fluid. Moreover, we find pore-scale correlations in the flow that are determined by the geometry of the medium. Our results suggest that, despite the considerable complexity of the pore space, fluid flow through it is not completely random.
In this paper we show the global well-posedness of solutions to a three-dimensional magnetohydrodynamical (MHD) model in porous media. Compared to the classical MHD equations, our system involves a nonlinear damping term in the momentum equations due to the "Brinkman-Forcheimer-extended-Darcy" law of flow in porous media.
Immiscible fluid-fluid displacement in porous media is of great importance in many engineering applications, such as enhanced oil recovery, agricultural irrigation, and geologic CO2 storage. Fingering phenomena, induced by the interface instability, are commonly encountered during displacement processes and somehow detrimental since such hydrodynamic instabilities can significantly reduce displacement efficiency. In this study, we report a possible adjustment in pore geometry which aims to suppress the capillary fingering in porous media with hierarchical structures. Through pore-scale simulat…
We generalize to three dimensions (3D) a recently developed improved multi-component pseudopotential lattice Boltzmann method and analyze its applicability to simulate flows through realistic porous media. The model is validated and characterized via benchmarks, and we investigate its performance by simulating the displacement of immiscible fluids in 3D geometries. Two samples are considered, namely, a pack of spheres obtained numerically, and a Bentheimer sandstone rock sample obtained experimentally. We show that, with this model it is possible to simulate realistic viscosity ratios, to tune…
Capillary energy barriers have important consequences for immiscible fluid flow in porous media. We derive time-and-space averaging theory to account for non-equilibrium behavior and understand the role of athermal capillary fluctuations in the context of their relationship to larger scale phenomenological equations. The formulation resolves several key challenges associated with two-fluid flow in porous media: (1) geometric and thermodynamic quantities are constructed as smooth functions of time based on time-and space averages; (2) averaged thermodynamics are developed for films; (3) multi-s…
We develop our existing two-dimensional lattice-gas model to simulate the flow of single-phase, binary-immiscible and ternary-amphiphilic fluids. This involves the inclusion of fixed obstacles on the lattice, together with the inclusion of ``no-slip'' boundary conditions. Here we report on preliminary applications of this model to the flow of such fluids within model porous media. We also construct fluid invasion boundary conditions, and the effects of invading aqueous solutions of surfactant on oil-saturated rock during imbibition and drainage are described.
