Automatic repeat request (ARQ) is widely used in modern communication systems to improve transmission reliability. In conventional ARQ protocols developed for systems with energy-unconstrained receivers, an acknowledgement/negative-acknowledgement (ACK/NACK) message is fed back when decoding succeeds/fails. Such kind of non-adaptive feedback consumes significant amount of energy, and thus will limit the performance of systems with energy harvesting (EH) receivers. In order to overcome this limitation and to utilize the harvested energy more efficiently, we propose a novel ARQ protocol for EH receivers, where the ACK feedback can be adapted based upon the receiver's EH state. Two conventional ARQ protocols are also considered. By adopting the packet drop probability (PDP) as the performance metric, we formulate the throughput constrained PDP minimization problem for a communication link with a non-EH transmitter and an EH receiver. Optimal reception policies including the sampling, decoding and feedback strategies, are developed for different ARQ protocols. Simulation results will show that the proposed ARQ protocol not only outperforms the conventional ARQs in terms of PDP, but can also achieve a higher throughput.
In the present paper, we propose a broadcast ARQ protocol based on the concept of index coding. In the proposed scenario, a server wishes to transmit a finite sequence of packets to multiple receivers via a broadcast channel with packet erasures until all of the receivers successfully receive all of the packets. In the retransmission phase, the server produces a coded packet as a retransmitted packet based on the side-information sent from the receivers via feedback channels. A notable feature of the proposed protocol is that the decoding process at the receiver side has low decoding complexit…
For decades, cellular networks have greatly evolved to support high data rates over reliable communication. Hybrid automatic-repeat-request (ARQ) is one of the techniques to make such improvement possible. However, this advancement is reduced at the cell edge where interference is not negligible. In order to overcome the challenge at the cell edge, the concept of interference-aware receiver has been recently proposed in which both desired and interference signals are successively decoded, called interference-aware successive decoding (IASD). Although IASD is the advanced receiver technology, i…
In modern communication systems with feedback, there are increasingly more scenarios where the transmitter has much less power than the receiver (e.g., medical implant devices), which we refer to as noise-asymmetric channels. For such channels, the feedback link is of higher quality than the forward link. However, feedback schemes for cellular communications, such as hybrid ARQ, do not fully utilize the high-quality feedback link. To this end, we introduce Compressed Error Hybrid ARQ, a generalization of hybrid ARQ tailored for noise-asymmetric channels; the receiver sends its estimated messag…
Hybrid-ARQ protocols have become common in many packet transmission systems due to their incorporation in various standards. Hybrid-ARQ combines the normal automatic repeat request (ARQ) method with error correction codes to increase reliability and throughput. In this paper, we look at improving upon this performance using feedback information from the receiver, in particular, using a powerful forward error correction (FEC) code in conjunction with a proposed linear feedback code for the Rayleigh block fading channels. The new hybrid-ARQ scheme is initially developed for full received packet …
We develop the proposal of non-systematic channel codes on the AWGN wire-tap channel. Such coding technique, based on scrambling, achieves high transmission security with a small degradation of the eavesdropper's channel with respect to the legitimate receiver's channel. In this paper, we show that, by implementing scrambling and descrambling on blocks of concatenated frames, rather than on single frames, the channel degradation needed is further reduced. The usage of concatenated scrambling allows to achieve security also when both receivers experience the same channel quality. However, in th…
We propose two schemes for selective-repeat ARQ protocols over packet erasure channels with unreliable feedback: (i) a hybrid ARQ protocol with soft combining at the receiver, and (ii) a coded ARQ protocol, by building on the uncoded baseline scheme for ARQ, developed by Ausavapattanakun and Nosratinia. Our method leverages discrete-time queuing and coding theory to analyze the performance of the proposed data transmission methods. We incorporate forward error-correction to reduce in-order delivery delay, and exploit a matrix signal-flow graph approach to analyze the throughput and delay of th…
Transmitter-receiver energy harvesting model is assumed, where both the transmitter and receiver are powered by random energy source. Given a fixed number of bits, the problem is to find the optimal transmission power profile at the transmitter and ON-OFF profile at the receiver to minimize the transmission time. Structure of the optimal offline strategy is derived together with an optimal offline policy. An online policy with competitive ratio of strictly less than two is also derived.
A joint transmitter-receiver energy harvesting model is considered, where both the transmitter and receiver are powered by (renewable) energy harvesting source. Given a fixed number of bits, the problem is to find the optimal transmission power profile at the transmitter and ON-OFF profile at the receiver to minimize the transmission time. With infinite capacity at both the transmitter and receiver, optimal offline and optimal online policies are derived. The optimal online policy is shown to be two-competitive in the arbitrary input case. With finite battery capacities at both ends, only rand…
In this paper, we investigate a multiple-input multiple-output (MIMO) system with simultaneous information detection (ID) and energy harvesting (EH) receiver. This point-to-point system operates in the vicinity of active interfering nodes. The receiver performs power splitting where a portion of received signal undergoes analog energy harvesting circuitry. Further, the information content of the other portion is extracted after performing digital beamforming. In this MIMO system, information carrier eigen-modes are not necessarily the eigen-modes with the strongest energy level. Hence, it is b…
We first consider an energy harvesting channel with fading, where only the transmitter harvests energy from natural sources. We bound the optimal long term throughput by a constant for a class of energy arrival distributions. The proposed method also gives a constant approximation to the capacity of the energy harvesting channel with fading. Next, we consider a more general system where both the transmitter and the receiver employ energy harvesting to power themselves. In this case, we show that finding an approximation to the optimal long term throughput is far more difficult, and identify a …
We study energy harvesting (EH) transmitter and receiver, where the receiver decodes data using the harvested energy from the nature and from an independent EH node, named helper. Helper cooperates with the receiver by transferring its harvested energy to the receiver over an orthogonal fading channel. We study an offline optimal power management policy to maximize the reliable information rate. The harvested energy in all three nodes are assumed to be known. We consider four different scenarios; First, for the case that both transmitter and the receiver have batteries, we show that the optima…
This paper studies online power control policies for outage minimization in a fading wireless link with energy harvesting transmitter and receiver. The outage occurs when either the transmitter or the receiver does not have enough energy, or the channel is in outage, where the transmitter only has the channel distribution information. Under infinite battery capacity and without retransmission, we prove that threshold-based power control policies are optimal. We thus propose disjoint/joint threshold-based policies with and without battery state sharing between the transmitter and receiver, resp…
We consider a secondary user with energy harvesting capability. We design access schemes for the secondary user which incorporate random spectrum sensing and random access, and which make use of the primary automatic repeat request (ARQ) feedback. The sensing and access probabilities are obtained such that the secondary throughput is maximized under the constraints that both the primary and secondary queues are stable and that the primary queueing delay is kept lower than a specified value needed to guarantee a certain quality of service (QoS) for the primary user. We consider spectrum sensing…
A multiple-input single-output cognitive radio downlink network is studied with simultaneous wireless information and power transfer. In this network, a secondary user coexists with multiple primary users and multiple energy harvesting receivers. In order to guarantee secure communication and energy harvesting, the problem of robust secure artificial noise-aided beamforming and power splitting design is investigated under imperfect channel state information. Specifically, the max-min fairness energy harvesting problem is formulated under the bounded channel state information error model. A one…
The focus of this paper is an information-theoretic study of retransmission protocols for reliable packet communication under a secrecy constraint. The hybrid automatic retransmission request (HARQ) protocol is revisited for a block-fading wire-tap channel, in which two legitimate users communicate over a block-fading channel in the presence of a passive eavesdropper who intercepts the transmissions through an independent block-fading channel. In this model, the transmitter obtains a 1-bit ACK/NACK feedback from the legitimate receiver via an error-free public channel. Both reliability and con…
Energy harvesting is a promising solution to prolong the operation of energy-constrained wireless networks. In particular, scavenging energy from ambient radio signals, namely wireless energy harvesting (WEH), has recently drawn significant attention. In this paper, we consider a point-to-point wireless link over the narrowband flat-fading channel subject to time-varying co-channel interference. It is assumed that the receiver has no fixed power supplies and thus needs to replenish energy opportunistically via WEH from the unintended interference and/or the intended signal sent by the transmit…
The difficulty of modeling energy consumption in communication systems leads to challenges in energy harvesting (EH) systems, in which nodes scavenge energy from their environment. An EH receiver must harvest enough energy for demodulating and decoding. The energy required depends upon factors, like code rate and signal-to-noise ratio, which can be adjusted dynamically. We consider a receiver which harvests energy from ambient sources and the transmitter, meaning the received signal is used for both EH and information decoding. Assuming a generalized function for energy consumption, we maximiz…
In this work, we consider a scenario wherein an energy harvesting wireless radio equipment sends information to multiple receivers alongside powering them. In addition to harvesting the incoming radio frequency (RF) energy, the receivers also harvest energy from {its environment (e.g., solar energy)}. This communication framework is captured by a fading Gaussian Broadcast Channel (GBC) with energy harvesting transmitter and receivers. In order to ensure {some quality of service (QoS)} in data reception among the receivers, we impose a \textit{minimum-rate} requirement on data transmission. For…
In this work, we analyze hybrid ARQ (HARQ) protocols over the independent block fading channel. We assume that the transmitter is unaware of the channel state information (CSI) but has a knowledge about the channel statistics. We consider two scenarios with respect to the feedback received by the transmitter: i) ''conventional'', one-bit feedback about the decoding success/failure (ACK/NACK), and ii) the multi-bit feedback scheme when, on top of ACK/NACK, the receiver provides additional information about the state of the decoder to the transmitter. In both cases, the feedback is used to alloc…
This letter deals with the joint information and energy processing at a receiver of a point-to-point communication channel. In particular, the trade-off between the achievable information rate and harvested energy for a multiple-antenna power splitting (PS) receiver is investigated. Here, the rate- energy region characterization is of particular interest, which is intrinsically a non-convex problem. In this letter, an efficient algorithm is proposed for obtaining an approximate solution to the problem in polynomial time. This algorithm is mainly based on the Taylor approximation in conjunction…
Future 5G systems will need to support ultra-reliable low-latency communications scenarios. From a latency-reliability viewpoint, it is inefficient to rely on average utility-based system design. Therefore, we introduce the notion of guaranteeable delay which is the average delay plus three standard deviations of the mean. We investigate the trade-off between guaranteeable delay and throughput for point-to-point wireless erasure links with unreliable and delayed feedback, by bringing together signal flow techniques to the area of coding. We use tiny codes, i.e. sliding window by coding with ju…
We consider a wireless network where multiple energy harvesting transmitters communicate with the common receiver in a time sharing manner. In each slot, a transmitter can either harvest energy or send its data to the receiver. Given a time deadline, the goal is to maximize the sum-rate of transmitters under random energy arrivals with both perfect and imperfect channel state information (CSI) at the receiver. The original sumrate maximization (SRM) problem is a non-convex mixed integer non-linear program (MINLP). To obtain the optimal scheduling policy, we first reduce the original optimizati…
In this work we consider incremental redundancy (IR) hybrid automatic repeat request (HARQ), where transmission rounds are carried out over independent block-fading channels. We propose the so-called multi-packet HARQ where the transmitter allows different packets to share the same channel block. In this way the resources (block) are optimally assigned throughout the transmission rounds. This stands in contrast with the conventional HARQ, where each transmission round occupies the entire block. We analyze superposition coding and time-sharing transmission strategies and we optimize the paramet…
We investigate if feedback can increase the capacity of an energy harvesting communication channel where a transmitter powered by an exogenous energy arrival process and equipped with a finite battery communicates to a receiver over a memoryless channel. For a simple special case where the energy arrival process is deterministic and the channel is a BEC, we explicitly compute the feed-forward and feedback capacities and show that feedback can strictly increase the capacity of this channel. Building on this example, we also show that feedback can increase the capacity when the energy arrivals a…
In this paper, we study information-theoretic limits for simultaneous wireless information and power transfer (SWIPT) systems employing a practical nonlinear radio frequency (RF) energy harvesting (EH) receiver. In particular, we consider a three-node system with one transmitter that broadcasts a common signal to separated information decoding (ID) and EH receivers. Owing to the nonlinearity of the EH receiver circuit, the efficiency of wireless power transfer depends significantly on the waveform of the transmitted signal. In this paper, we aim to answer the following fundamental question: Wh…
Harvesting energy from ambient environment is a new promising solution to free electronic devices from electric wire or limited-lifetime battery, which may find very significant applications in sensor networks and body-area networks. This paper mainly investigate the fundamental limits of information transmission in wireless communication system with RF-based energy harvesting, in which a master node acts not only as an information source but also an energy source for child node while only information is transmitted back from child to master node. Three typical structures: optimum receiver, or…
Energy harvesting is a technology for enabling green, sustainable, and autonomous wireless networks. In this paper, a large-scale wireless network with energy harvesting transmitters is considered, where a group of transmitters forms a cluster to cooperatively serve a desired receiver amid interference and noise. To characterize the link-level performance, closed-form expressions are derived for the transmission success probability at a receiver in terms of key parameters such as node densities, energy harvesting parameters, channel parameters, and cluster size, for a given cluster geometry. T…
Simultaneous wireless information and power transfer (SWIPT) is a promising solution for enabling long-life, and self-sustainable wireless networks. In this thesis, we propose a practical non-linear energy harvesting (EH) model and design a resource allocation algorithm for SWIPT systems. In particular, the algorithm design is formulated as a non-convex optimization problem for the maximization of the total harvested power at the EH receivers subject to quality of service (QoS) constraints for the information decoding (ID) receivers. To circumvent the non-convexity of the problem, we transform…
Since radio signals carry both energy and information at the same time, a unified study on simultaneous wireless information and power transfer (SWIPT) has recently drawn a significant attention for achieving wireless powered communication networks. In this paper, we study a multiple-input single-output (MISO) multicast SWIPT network with one multi-antenna transmitter sending common information to multiple single-antenna receivers simultaneously along with opportunistic wireless energy harvesting at each receiver. From the practical consideration, we assume that the channel state information (…
This paper introduces a novel technique that enables access by a cognitive secondary user (SU) to a spectrum occupied by an incumbent primary user (PU) that employs Type-I Hybrid ARQ. The technique allows the SU to perform selective retransmissions of SU data packets that have not been successfully decoded in the previous attempts. The temporal redundancy introduced by the PU ARQ protocol and by the selective retransmission process of the SU can be exploited by the SU receiver to perform interference cancellation (IC) over multiple transmission slots, thus creating a "clean" channel for the de…
We consider the problem of Simultaneous Wireless Information and Power Transfer (SWIPT) over a fading multiple access channel with additive Gaussian noise. The transmitters as well as the receiver harvest energy from ambient sources. We assume that the transmitters have two classes of data to send, viz. delay sensitive and delay tolerant data. Each transmitter sends the delay sensitive data at a certain minimum rate irrespective of the channel conditions (fading states). In addition, if the channel conditions are good, the delay tolerant data is sent. {Along with data, the transmitters also tr…
In this letter, we propose a practical non-linear energy harvesting model and design a resource allocation algorithm for simultaneous wireless information and power transfer (SWIPT) systems. The algorithm design is formulated as a non-convex optimization problem for the maximization of the total harvested power at energy harvesting receivers subject to minimum required signal-to-interference-plus-noise ratios (SINRs) at multiple information receivers. We transform the considered non-convex objective function from sum-of-ratios form into an equivalent objective function in subtractive form, whi…
In this paper, we develop optimal energy-bandwidth allocation algorithms in fading channels for multiple energy harvesting transmitters, each may communicate with multiple receivers via orthogonal channels. We first assume that the side information of both the channel states and the energy harvesting states is known for $K$ time slots {\em a priori}, and the battery capacity and the maximum transmission power in each time slot are bounded. The objective is to maximize the weighted sum-rate of all transmitters over the $K$ time slots by assigning the transmission power and bandwidth for each tr…
We consider a secondary user (SU) with energy harvesting capability. We design access schemes for the SU which incorporate random spectrum sensing and random access, and which make use of the primary automatic repeat request (ARQ) feedback. We study two problem-formulations. In the first problem-formulation, we characterize the stability region of the proposed schemes. The sensing and access probabilities are obtained such that the secondary throughput is maximized under the constraints that both the primary and secondary queues are stable. Whereas in the second problem-formulation, the sensin…
In this paper, we propose an online power allocation scheme to maximize the time averaged sum rate for multiple downlink receivers with energy harvesting transmitter. The transmitter employs non-orthogonal multiple access (NOMA) and/or orthogonal multiple access (OMA) to transmit data to multiple users. Additionally, we consider the scenario where each individual user has a quality of service constraint on its required instantaneous rate. The decisions of total transmit power and power allocation for different users in a given time slot are obtained with the help of Lyapunov optimization techn…
Transmitter switching can provide resiliency and robustness to a communication system with multiple energy harvesting transmitters. However, excessive transmitter switching will bring heavy control overhead. In this paper, a geometric projection-based transmitter switching policy is proposed for a communication system with multiple energy harvesting transmitters and one receiver, which can reduce the number of switches. The results show that the proposed transmitter switching policy outperforms several heuristic ones.
In this paper, we design a resource allocation algorithm for multiuser simultaneous wireless information and power transfer systems for a realistic non-linear energy harvesting (EH) model. In particular, the algorithm design is formulated as a non-convex optimization problem for the maximization of the long-term average total harvested power at EH receivers subject to quality of service requirements for information decoding receivers. To obtain a tractable solution, we transform the corresponding non-convex sum-of-ratios objective function into an equivalent objective function in parametric su…
An underlay cognitive radio network with energy harvesting is considered which operates in slotted fashion. The primary user (PU) transmits with a constant power in each slot, while the secondary user (SU) either harvests energy from primary's transmission or transmits its data. We propose an optimal offline harvest-or-transmit strategy where in each slot, SU takes a decision whether to harvest energy or transmit its data limiting interference at the primary receiver. We aim to maximize the achievable rate of SU under energy causality and interference constraints. The optimization problem is f…
With the advancement of battery technology, energy harvesting communication systems attracted great research attention in recent years. However, energy harvesting communication systems with multiple transmitters and multiple receivers have not been considered yet. In this paper, the problem of broadcasting in a communication system with multiple energy harvesting transmitters and multiple receivers is studied. First, regarding the transmitters as a 'hole transmitter' [1], the optimal total transmission power is obtained and the optimal power allocation policy in [2] is extended to our system s…
We consider the effects of decoding costs in energy harvesting communication systems. In our setting, receivers, in addition to transmitters, rely solely on energy harvested from nature, and need to spend some energy in order to decode their intended packets. We model the decoding energy as an increasing convex function of the rate of the incoming data. In this setting, in addition to the traditional energy causality constraints at the transmitters, we have the decoding causality constraints at the receivers, where energy spent by the receiver for decoding cannot exceed its harvested energy. W…
RF energy harvesting can be used to power communication devices so that perpetual operation of such devices can be ensured. We consider a RF energy harvesting underlay cognitive radio system operating in slotted fashion. The primary user (PU) is equipped with a reliable power source and transmits with a constant power in all the slots. However, the secondary user (SU) harvests energy from primary's transmission and simultaneously transmits it's own data such that interference at the primary receiver (PR) remains below an acceptable threshold. At the secondary transmitter (ST), each time slot i…
This paper analyzes the communication between two energy harvesting wireless sensor nodes. The nodes use automatic repeat request and forward error correction mechanism for the error control. The random nature of available energy and arrivals of harvested energy may induce interruption to the signal sampling and decoding operations. We propose a selective sampling scheme where the length of the transmitted packet to be sampled depends on the available energy at the receiver. The receiver performs the decoding when complete samples of the packet are available. The selective sampling information…
The problems of energy harvesting in wireless com- munication systems have recently drawn much attention. In this paper, we focus on the investigation of energy harvesting maximization (EHM) in the important secrecy multi-input multi- output (MIMO) systems where little research has been done due to their complexity. Particularly, this paper studies the resource allocation strategies in MIMO wiretap channels, wherein we attempt to maximize the harvested energy by one or multiple multi-antenna energy receivers (ERs) (potential eavesdropper) while guaranteeing the secure communication for the mul…
In this paper, we investigate joint beamforming for energy-throughput tradeoff in a sustainable cloud radio access network system, where multiple base stations (BSs) powered by independent renewable energy sources will collaboratively transmit wireless information and energy to the data receiver and the energy receiver simultaneously. In order to obtain the optimal joint beamforming design over a finite time horizon, we formulate an optimization problem to maximize the throughput of the data receiver while guaranteeing sufficient RF charged energy of the energy receiver. Although such problem …
In this paper, we study a multi-user multiple-input-multiple-output secrecy simultaneous wireless information and power transfer (SWIPT) channel which consists of one transmitter, one cooperative jammer (CJ), multiple energy receivers (potential eavesdroppers, ERs), and multiple co-located receivers (CRs). We exploit the dual of artificial noise (AN) generation for facilitating efficient wireless energy transfer and secure transmission. Our aim is to maximize the minimum harvested energy among ERs and CRs subject to secrecy rate constraints for each CR and total transmit power constraint. By i…
We study information-theoretic limits for simultaneous wireless information and power transfer (SWIPT) systems employing nonlinear radio frequency (RF) energy harvesting (EH) receivers (Rxs). In particular, we consider a SWIPT system with one transmitter that broadcasts a common signal to an information decoding (ID) Rx and multiple EH Rxs. Owing to the nonlinearity of the EH Rxs' circuitry, the efficiency of wireless power transfer depends on the waveform of the transmitted signal. We aim to answer the following fundamental question: What is the optimal input distribution of the transmit sign…
Simultaneous wireless information and power transfer (SWIPT) is an appealing research area because both information and energy can be delivered to wireless devices simultaneously. In this paper, we propose a diplexer-based receiver architecture that can utilizes both the doubling frequency and baseband signals after the mixer. The baseband signals are used for information decoding and the doubling frequency signals are converted to direct current for energy harvesting. We analyze the signal in the receiver and find that the power of the energy harvested is equal to that of information decoded.…
This paper investigates a secure energy efficiency (SEE) optimization problem in a multiple-input single-output (MISO) underlay cognitive radio (CR) network. In particular, a multi-antenna secondary transmitter (SU-Tx) simultaneously sends secured information and energy to a secondary receiver (SU-Rx) and an energy receiver (ER), respectively, in the presence of a primary receiver (PU-Rx). It is assumed that the SU-Rx, ER and PU-Rx are each equipped with a single antenna. In addition, the SU-Tx should satisfy constraints on maximum interference leakage to the PU-Rx and minimum harvested energy…
In this paper, we consider an overlay cognitive radio network, in which a secondary transmitter (ST) is willing to relay the information of a primary transmitter toward a primary receiver. In return, ST can access the licensed band to send its own information superimposed with the primary signal to a secondary receiver. The power-limited ST uses a power splitting protocol to harvest energy from its received signal to increase its transmit power. We analyze the performance of the primary and the secondary systems under independent Nakagami-m fading by deriving their corresponding outage probabi…
A multiple-input single-output cognitive radio downlink network is studied with simultaneous wireless information and power transfer. In this network, a secondary user coexists with multiple primary users and multiple energy harvesting receivers. In order to guarantee secure communication and energy harvesting, the problem of robust secure artificial noise-aided beamforming and power splitting design is investigated under imperfect channel state information (CSI). Specifically, the transmit power minimization problem and the max-min fairness energy harvesting problem are formulated for both th…
In this paper, short-term throughput optimal power allocation policies are derived for an energy harvesting transmitter with energy storage losses. In particular, the energy harvesting transmitter is equipped with a battery that loses a fraction of its stored energy. Both single user, i.e. one transmitter-one receiver, and the broadcast channel, i.e., one transmitter-multiple receiver settings are considered, initially with an infinite capacity battery. It is shown that the optimal policies for these models are threshold policies. Specifically, storing energy when harvested power is above an u…
This paper presents a design methodology for optimal transmission energy allocation at a sensor equipped with energy harvesting technology for remote state estimation of linear stochastic dynamical systems. In this framework, the sensor measurements as noisy versions of the system states are sent to the receiver over a packet dropping communication channel. The packet dropout probabilities of the channel depend on both the sensor's transmission energies and time varying wireless fading channel gains. The sensor has access to an energy harvesting source which is an everlasting but unreliable en…
We study the dynamic power splitting for simultaneous wireless information and power transfer (SWIPT) in the ergodic fading channel. Considering the nonlinearity of practical energy harvesting circuits, we adopt the realistic nonlinear energy harvesting (EH) model rather than the idealistic linear EH model. To characterize the optimal rate-energy (RE) tradeoff, we consider the problem of maximizing the R-E region, which is nonconvex. We solve this challenging problem for two different cases of the channel state information (CSI): (i) when the CSI is known only at the receiver (the CSIR case) a…
We consider an AWGN channel with a transmitter powered by an energy harvesting source. The node is equipped with a finite energy buffer. Such a system can be modelled as a channel with side information (about energy in the energy buffer) causally known at the transmitter. The receiver may or may not have the side information. We prove that Markov energy management policies are sufficient to achieve the capacity of the system and provide a single letter characterization for the capacity. The computation of the capacity is expensive. Therefore, we discuss an achievable scheme that is easy to com…
Energy harvesting has been developed as an effective technology for communication systems in order to extend the lifetime of these systems. In this work, we consider a singleuser energy harvesting wireless communication system, in which arrival data and harvested energy curves are modeled as continuous functions. For the single-user model, our first goal is to find an offline algorithm, which maximizes the amount of data which is transmitted to the receiver node by a given deadline. If more than one scheme exists that transmits the maximum data, we choose the one with minimum utilized energy a…
Simultaneous information and power transfer over the wireless channels potentially offers great convenience to mobile users. Yet practical receiver designs impose technical constraints on its hardware realization, as practical circuits for harvesting energy from radio signals are not yet able to decode the carried information directly. To make theoretical progress, we propose a general receiver operation, namely, dynamic power splitting (DPS), which splits the received signal with adjustable power ratio for energy harvesting and information decoding, separately. Three special cases of DPS, nam…
In this paper, we consider the energy-bandwidth allocation for a network with multiple broadcast channels, where the transmitters access the network orthogonally on the assigned frequency band and each transmitter communicates with multiple receivers orthogonally or non-orthogonally. We assume that the energy harvesting state and channel gain of each transmitter can be predicted for $K$ slots {\em a priori}. To maximize the weighted throughput, we formulate an optimization problem with $O(MK)$ constraints, where $M$ is the number of the receivers, and decompose it into the energy and bandwidth…
