In this review we discuss spin and charge transport properties in graphene-based single-layer and few-layer spin-valve devices. We give an overview of challenges and recent advances in the field of device fabrication and discuss two of our fabrication methods in more detail which result in distinctly different device performances. In the first class of devices, Co/MgO electrodes are directly deposited onto graphene which results in rough MgO-to-Co interfaces and favor the formation of conducting pinholes throughout the MgO layer. We show that the contact resistance area product (R$_c$A) is a benchmark for spin transport properties as it scales with the measured spin lifetime in these devices indicating that contact-induced spin dephasing is the bottleneck for spin transport even in devices with large R$_c$A values. In a second class of devices, Co/MgO electrodes are first patterned onto a silicon substrate. Subsequently, a graphene-hBN heterostructure is directly transferred onto these prepatterned electrodes which provides improved interface properties. This is seen by a strong enhancement of both charge and spin transport properties yielding charge carrier mobilities exceeding 20000 cm$^2$/(Vs) and spin lifetimes up to 3.7 ns at room temperature. We discuss several shortcomings in the determination of both quantities which complicates the analysis of both extrinsic and intrinsic spin scattering mechanisms. Furthermore, we show that contacts can be the origin of a second charge neutrality point in gate dependent resistance measurements which is influenced by the quantum capacitance of the underlying graphene layer.
We first report the all-electrical spin injection and detection in CoFe/MgO/moderately doped n-Ge contact at room temperature (RT), employing threeterminal Hanle measurements. A sizable spin signal of ~170 kΩ μm^2 has been observed at RT, and the analysis using a single-step tunneling model gives a spin lifetime of ~120 ps and a spin diffusion length of ~683 nm in Ge. The observed spin signal shows asymmetric bias and temperature dependences which are strongly related to the asymmetry of the tunneling process.
We fabricated a non-local spin valve device with Co-MgO injector/detector tunnel contacts on a graphene spin channel. In this device, the spin polarization of the injector contact can be tuned by both the injector current bias and the gate voltage. The spin polarization can be turned off and even inverted. This behavior enables a spin transistor where the signal is switched off by turning off the spin injection using the field-effect. We propose a model based on a gate-dependent shift of the minimum in the graphene density of states with respect to the tunneling density of states of cobalt, wh…
We report the thermal spin injection and accumulation in crystalline CoFe/MgO tunnel contacts to n-type Si through Seebeck spin tunneling (SST). With the Joule heating (laser heating) of Si (CoFe), the thermally induced spin accumulation is detected by means of the Hanle effect for both polarities of the temperature gradient across the tunnel contact. The magnitude of the thermal spin signal scales linearly with the heating power and its sign is reversed as we invert the temperature gradient, demonstrating the major features of SST and thermal spin accumulation. We observe that, for the Si (Co…
We have investigated electrical spin injection from Ni81Fe19 into an InAs quantum well through MgO tunneling barrier for potential application to InAs-based spin field effect transistor. Injected spin polarized current were detected in both nonlocal and local spin valve set-ups and the spin diffusion length and spin injection efficiency were analyzed. The spin diffusion length was estimated to be 1.6 μm in nonlocal set-up at 1.4 K. The spin polarization of Ni81Fe19/MgO/InAs as-deposited sample was relealed to be 6.9 %, while increased spin polarization of 8.9 % was observed by additional therm…
We demonstrated that the spin injection/extraction efficiency is enhanced by an ultrathin Mg insertion layer (<= 2 nm) in Fe/Mg/MgO/n+-Si tunnel junctions. In diode-type vertical three-terminal devices fabricated on a Si substrate, we observed the narrower three-terminal Hanle (N-3TH) signals indicating true spin injection into Si, and estimated the spin polarization in Si to be 16% when the thickness of the Mg insertion layer is 1 nm, whereas no N-3TH signal was observed without Mg insertion. This means that the spin injection/extraction efficiency is enhanced by suppressing the formation of …
We report on the fabrication and characterization of vertical spin-valve structures using a thick epitaxial MgO barrier as spacer layer and a graphene-passivated Ni film as bottom ferromagnetic electrode. The devices show robust and scalable tunnel magnetoresistance, with several changes of sign upon varying the applied bias voltage. These findings are explained by a model of phonon-assisted transport mechanisms that relies on the peculiarity of the band structure and spin density of states at the hybrid graphene|Ni interface.
We investigate spin and charge transport in both single and bilayer graphene non-local spin-valve devices. Similar to previous studies on bilayer graphene, we observe an inverse dependence of the spin lifetime on the carrier mobility in our single layer devices. This general trend is only observed in devices with large contact resistances. Furthermore, we observe a second Dirac peak in devices with long spin lifetimes. This results from charge transport underneath the contacts. In contrast, all devices with low ohmic contact resistances only exhibit a single Dirac peak. Additionally, the spin …
Alloying Fe electrodes with V, through reduced FeV/MgO interface mismatch in epitaxial magnetic tunnel junctions with MgO barriers, notably suppresses both nonmagnetic (parallel) and magnetic (antiparallel) state 1/f noise and enhances tunnelling magnetoresistance (TMR). A comparative study of the room temperature electron transport and low frequency noise in Fe1-xVx/MgO/Fe and Fe/MgO/Fe1-xVx MTJs with 0 <= x <= 0.25 reveals that V doping of the bottom electrode for x < 0.1 reduces in nearly 2 orders of magnitude the normalized nonmagnetic and magnetic 1/f noise. We attribute the enhanced TMR …
Efforts to achieve efficient injection of spin-polarized electrons into a semiconductor, a key prerequisite for developing electronics that exploit the electron's spin degree of freedom, have so far met with limited success. Here we report experimental studies of lateral spin injection and detection through electrodeposited Fe/GaAs tunnel contacts. We demonstrate spin injection efficiencies two orders of magnitude higher than for state-of-the-art contacts fabricated via ultra-high-vacuum methods, including those with MgO or Al2O3 tunnel barriers. To account for this enhancement, we propose tha…
In this paper we present theoretical studies of spin dependent transport in Fe/Cr/MgO/Fe tunnel junctions with non-collinear alignment of magnetizations of metallic layers comprising these MTJs. Calculations are performed with use of non-equilibrium Green function technique in the framework of Keldysh formalism. WKB approximation is used for wave and Green functions in the trapezoidal barrier region under applied voltage. Electronic structure of ferromagnetic electrodes is modeled with two bands model, i.e. with majority s-electrons and minority d-holes. Furthermore, we introduce s-d hybridiza…
Recently, it has been shown that oxide barriers in graphene-based non-local spin-valve structures can be the bottleneck for spin transport. The barriers may cause spin dephasing during or right after electrical spin injection which limit spin transport parameters such as the spin lifetime of the whole device. An important task is to evaluate the quality of the oxide barriers of both spin injection and detection contacts in a fabricated device. To address this issue, we discuss the influence of spatially inhomogeneous oxide barriers and especially conducting pinholes within the barrier on the b…
We report the fabrication of perpendicular ferromagnetic electrodes for tunneling devices consist of van der Waals heterostructure. We found MgO/Co/Pt films on Hexagonal BN shows perpendicular magnetic anisotropy (PMA) with the easy axis perpendicular to the substrate. Vacuum annealing enhances the perpendicular anisotropy. The easy axis along the perpendicular direction persists up to room temperature with the Pt layer thickness ranges from 1.5 to 5 nm. We employed the PMA electrodes to construct tunneling devices on graphene and monolayer WSe2, where spin injection characteristics and field …
Strength of the the symmetry spin filtering effect (as defined by the asymptotic behavior of the tunneling magnetoresistance (TMR) at large barrier thicknesses induced by this effect) is studied for the Fe/MgO/Fe magnetic tunnel junctions (MTJ). Based on the analysis of the band structure of bulk Fe and complex band structure of MgO we predict \emph{native} for the symmetry spin filtering effect linear increase of the TMR in Fe/MgO/Fe MTJ with increasing number of MgO layers, $N$. \emph{Ab initio} calculations of transmission functions performed for the Fe/MgO/Fe MTJ confirm our theoretical pr…
Thin electrodes of magnetic tunnel junctions can show superparamagnetism at surprisingly low temperature. We analysed their thermally induced switching for varying temperature, magnetic and electric field. Although the dwell times follow an Arrhenius law, they are orders of magnitude too small compared to a model of single domain activation. Including entropic effects removes this inconsistency and leads to a magnetic activation volume much smaller than that of the electrode. Comparing data for varying barrier thickness then allows to separate the impact of Zeman energy, spin-transfer-torque a…
Employing femtosecond laser pulses in front and back side pumping of Au/Fe/MgO(001) combined with detection in two-photon photoelectron emission spectroscopy we analyze local relaxation dynamics of excited electrons in buried Fe, injection into Au across the Fe-Au interface, and electron transport across the Au layer at 0.6 to 2.0 eV above the Fermi energy. By analysis as a function of Au film thickness we obtain the electron lifetimes of bulk Au and Fe and distinguish the relaxation in the heterostructure's constituents. We also show that the excited electrons propagate through Au in a superd…
We demonstrate magnetization switching in out-of-plane magnetized Ta\CoFeB\MgO nanowires by current pulse injection along the nanowires, both with and without a constant and uniform magnetic field collinear to the current direction. We deduce that an effective torque arising from spin-orbit effects in the multilayer drives the switching mechanism. While the generation of a component of the magnetization along the current direction is crucial for the switching to occur, we observe that even without a longitudinal field thermally generated magnetization fluctuations can lead to switching. Analys…
Combined measurements of normal and inverted Hanle effects in CoFe/MgO/semiconductor (SC) contacts reveal the effect of spin relaxation rate on the interfacial spin depolarization (ISD) from local magnetic fields. Despite the similar ferromagnetic electrode and interfacial roughness in both CoFe/MgO/Si and CoFe/MgO/Ge contacts, we have observed clearly different features of the ISD depending on the host SC. The precession and relaxation of spins in different SCs exposed to the local fields from more or less the same ferromagnets give rise to a notably different ratio of the inverted Hanle sign…
By successive oxygen treatments of graphene non-local spin-valve devices we achieve a gradual increase of the contact resistance area products ($R_cA$) of Co/MgO spin injection and detection electrodes and a transition from linear to non-linear characteristics in the respective differential dV-dI-curves. With this manipulation of the contacts both spin lifetime and amplitude of the spin signal can significantly be increased by a factor of seven in the same device. This demonstrates that contact-induced spin dephasing is the bottleneck for spin transport in graphene devices with small $R_cA$ va…
We study the magnon spin transport in the magnetic insulator yttrium iron garnet (YIG) in a nonlocal experiment and compare the magnon spin excitation and detection for the heavy metal paramagnetic electrodes platinum (Pt|YIG|Pt) and tantalum (Ta|YIG|Ta). The electrical injection and detection processes rely on the (inverse) spin Hall effect in the heavy metals and the conversion between the electron spin and magnon spin at the heavy metal|YIG interface. Pt and Ta possess opposite signs of the spin Hall angle. Furthermore, their heterostructures with YIG have different interface properties, i.…
Room temperature local magnetoresistance in two-terminal scheme is reported. By employing 1.6 nm-thick MgO tunnel barrier, spin injection efficiency is increased, resulting in large non-local magnetoresistance. The magnitude of the non-local magnetoresistance is estimated to be 0.0057 ohm at room temperature. As a result, a clear rectangle signal is observed in local magnetoresistance measurement even at room temperature. We also investigate the origin of local magnetoresistance by measuring the spin accumulation voltage of each contact separately.
Direct demonstration of time-reversal-symmetry-breaking spin injection from a compensated magnet
CIC nanoGUNE BRTA（nanoGUNE BRTA 研究中心）；University of the Basque Country (UPV/EHU)（巴斯克大学）；Institute of Physics, Czech Academy of Sciences（捷克科学院物理研究所）；Charles University（查理大学）；TUD University of Technology Dresden（德累斯顿工业大学）；Universidad del Norte（北方大学）；Johannes Gutenberg Universität Mainz（美因茨约翰内斯古腾堡大学）；UdelaR（乌拉圭共和国大学）；University of Jyvaskyla（耶瓦斯基莱大学）；Aix-Marseille Univ.（艾克斯-马赛大学）
The bias dependence of the tunnel magnetoresistance (TMR) of Fe/MgO/Fe tunnel junctions is investigated theoretically with a fully self-consistent scheme that combines the non-equilibrium Green's functions method with density functional theory. At voltages smaller than 20 mVolt the I-V characteristics and the TMR are dominated by resonant transport through narrow interface states in the minority spin-band. In the parallel configuration this contribution is quenched by a voltage comparable to the energy width of the interface state, whereas it persists at all voltages in the anti-parallel confi…
We present spin transport studies on bi- and trilayer graphene non-local spin-valves which have been fabricated by a bottom-up fabrication method. By this technique, spin injection electrodes are first deposited onto Si$^{++}$/SiO$_2$ substrates with subsequent mechanical transfer of a graphene/hBN heterostructure. We showed previously that this technique allows for nanosecond spin lifetimes at room temperature combined with carrier mobilities which exceed 20,000 cm$^2$/(Vs). Despite strongly enhanced spin and charge transport properties, the MgO injection barriers in these devices exhibit con…
Spin-dependent transport through an endohedral fullerene Co@C$_{60}$ dimer with gold electrodes is explored theoretically using density functional and extended Hückel theory. Density of states spin polarizations up to 95%, due to spin-splitting of Co 3d orbitals, are found by varying the gate and/or bias voltage. The current-voltage characteristics and strong (up to 100%) spin polarization of the current indicate that the device can be utilized for highly efficient spin injection into nonmagnetic conductors. This finding opens the way to the realization of electrostatically tuned spintronic na…
We present a new fabrication method of graphene spin-valve devices which yields enhanced spin and charge transport properties by improving both the electrode-to-graphene and graphene-to-substrate interface. First, we prepare Co/MgO spin injection electrodes onto Si$^{++}$/SiO$_2$. Thereafter, we mechanically transfer a graphene-hBN heterostructure onto the prepatterned electrodes. We show that room temperature spin transport in single-, bi- and trilayer graphene devices exhibit nanosecond spin lifetimes with spin diffusion lengths reaching 10$μ$m combined with carrier mobilities exceeding 20,0…
The influence of insertion of an ultra-thin NiO layer between the MgO barrier and ferromagnetic electrode in magnetic tunnel junctions has been investigated by measuring the tunneling magnetoresistance and the X-ray magnetic circular dichroism (XMCD). The magnetoresistance shows a high asymmetry with respect to bias voltage, giving rise to a negative value of -16% at 2.8 K. We attribute this to the formation of non-collinear spin structures in the NiO layer as observed by XMCD. The magnetic moments of the interface Ni atoms tilt from the easy axis due to exchange interaction and the tilting an…
We show spin lifetimes of 12.6 ns and spin diffusion lengths as long as 30.5 μm in single layer graphene non-local spin transport devices at room temperature. This is accomplished by the fabrication of Co/MgO-electrodes on a Si/SiO$_2$ substrate and the subsequent dry transfer of a graphene-hBN-stack on top of this electrode structure where a large hBN flake is needed in order to diminish the ingress of solvents along the hBN-to-substrate interface. Interestingly, long spin lifetimes are observed despite the fact that both conductive scanning force microscopy and contact resistance measurement…
We generalize Landauer's theory of ballistic transport in a one-dimensional (1D) conductor to situations where charge carrier injection and extraction are not any more confined to electrodes at either end of the channel, but may occur along its whole length. This type of distributed injection is expected to occur from the two-dimensional (2D) bulk of, e.g., a quantum spin (or anomalous) Hall insulator to its topologically protected edge states. We apply our conceptual solution to the case of two metal electrodes contacting the 2D bulk, enabling us to derive criteria that discriminate ballistic…
The quest for a spin-polarized organic light emitting diode (spin-OLED) is a common goal in the emerging fields of molecular electronics and spintronics. In this device two ferromagnetic electrodes are used to enhance the electroluminescence intensity of the OLED through a magnetic control of the spin polarization of the injected carriers. The major difficulty is that the driving voltage of an OLED device exceeds of a few volts, while spin injection in organic materials is only efficient at low voltages. We report here the fabrication of a spin-OLED that uses a conjugated polymer as bipolar sp…
There has been much interest in the injection and detection of spin polarized carriers in semiconductors for the purposes of developing novel spintronic devices. Here we report the electrical injection and detection of spin-polarized carriers into Nb-doped strontium titanate (STO) single crystals and La-doped STO epitaxial thin films using MgO tunnel barriers and the three-terminal Hanle technique. Spin lifetimes of up to ~100 ps are measured at room temperature and vary little as the temperature is decreased to low temperatures. However, the mobility of the STO has a strong temperature depend…
The bias dependence of spin injection in graphene lateral spin valves is systematically studied to determine the factors affecting the tunneling spin injection efficiency. Three types of junctions are investigated, including MgO and hexagonal boron nitride (hBN) tunnel barriers and direct contacts. A DC bias current applied to the injector electrode induces a strong nonlinear bias dependence of the nonlocal spin signal for both MgO and hBN tunnel barriers. Furthermore, this signal reverses its sign at a negative DC bias for both kinds of tunnel barriers. The analysis of the bias dependence for…
We present a study of the tunnel magneto-Seebeck (TMS) effect in MgO based magnetic tunnel junctions (MTJs). The electrodes consist of CoFeB with in-plane magnetic anisotropy. The temperature gradients which generate a voltage across the MTJs layer stack are created using laser heating. Using this method, the temperature can be controlled on the micrometer length scale: here, we investigate, how both, the TMS voltage and the TMS effect, depend on the size, position and intensity of the applied laser spot. For this study, a large variety of different temperature distributions was created across…
We experimentally study spin accumulation in an aluminium island with all dimensions smaller than the spin relaxation length, so that the spin imbalance throughout the island is uniform. Electrical injection and detection of the spin accumulation are carried out in a four terminal geometry by means of four cobalt electrodes connected to the island through tunnel barriers. We model the system theoretically and we investigate the role of the ferromagnetic electrodes on the spin accumulation at the limit at which the electron diffusion time can be neglected. We present measurements of spin accumu…
The electrical injection of spin polarized electrons in a semiconductor can be achieved in principle by driving a current from a ferromagnetic metal, where current is known to be significantly spin polarized, into the semiconductor via ohmic conduction. For detection a second ferromagnet can be used as drain. We studied submicron lateral spin valve junctions, based on high mobility InAs/AlSb two-dimensional electron gas (2DEG), with Ni, Co and Permalloy as ferromagnetic electrodes. In the standard geometry it is very difficult to separate true spin injection from other effects, including local…
A Josephson tunnel junction transistor based on quasiparticle injection is proposed. Its operation relies on the manipulation of the electron distribution in one of the junction electrodes. This is accomplished by injecting quasiparticle current through the junction electrode by two additional tunnel coupled superconductors. Both large supercurrent enhancement and fast quenching can be achieved with respect to equilibrium by varying quasiparticle injection for proper temperature regimes and suitable superconductor combinations. Joined with large power gain this makes the device attractive for …
Although the electrical injection, transport and detection of spins in silicon have been achieved, the induced spin accumulation was much smaller than expected and desired, limiting the potential impact of Si-based spintronic devices. Here, using non-local spin-transport devices with an n-type Si channel and Fe/MgO magnetic tunnel contacts, we demonstrate that it is possible to create a giant spin accumulation in Si, with the spin splitting reaching 13 meV at 10 K and 3.5 meV at room temperature. The non-local spin signals are in good agreement with a numerical evaluation of spin injection and…
We report for the first time enhancement of the supercurrent by means of injection in a mesoscopic three terminal planar SNSNS device made of Al on GaAs. When a current is injected from one of the superconducting Al electrodes at an injection bias $V=Δ(T)/e$, the DC Josephson current between the other two superconducting electrodes has a maximum, giving evidence for an enhancement due to a non-equilibrium injection into bound Andreev states of the underlying semiconductor. The effect persists to temperatures where the equilibrium supercurrent has vanished.
A nanoelectromechanical weak link composed of a carbon nanotube suspended between two normal electrodes in a gap between two superconducting leads is considered. The nanotube is treated as a movable single-level quantum dot in which the position-dependent superconducting order parameter is induced due to the Cooper pair tunneling. We show that electron tunneling processes significantly affect the state of the mechanical subsystem. We found that at a given direction of the applied voltage between the electrodes, the stationary state of the mechanical subsystem has a Boltzmann form with an effec…
The quantum interaction between molecules and electrode s material at molecules-electrode interfaces is a major ingredient in the electronic transport properties of organic junctions. Driven by the coupling strength between the two materials, it results mainly in a broadening and an energy shift of the interacting molecular orbitals. Using new electrodes materials, such as the recent semi-conducting two-dimensional nanomaterials, has become a recent challenge in the field of molecular-organic electronics that opens new possibilities for controlling the interfacial electronic properties and thu…
A charge flow through a magnetic tunnel junction (MTJ) leads to the generation of a spin-polarized current which exerts a spin-transfer torque (STT) on the magnetization. When the density of applied direct current exceeds some critical value, the STT excites high-frequency magnetization precession in the "free" electrode of MTJ. Such precession gives rise to microwave output voltage and, furthermore, can be employed for spin pumping into adjacent normal metal or semiconductor. Here we describe theoretically the spin dynamics and charge transport in the CoFeB/MgO/CoFeB/Au tunneling heterostruct…
We show nonlocal spin transport in n-Ge based lateral spin-valve devices with highly ordered Co_2FeSi/n^+-Ge Schottky tunnel contacts. Clear spin-valve signals and Hanle-effect curves are demonstrated at low temperatures, indicating generation, manipulation, and detection of pure spin currents in n-Ge. The obtained spin generation efficiency of ~ 0.12 is about two orders of magnitude larger than that for a device with Fe/MgO tunnel-barrier contacts reported previously. Taking the spin related behavior with temperature evolution into account, we infer that it is necessary to simultaneously demo…
High-performance solution-processed short-channel carbon nanotube (CNT) thin film transistors (TFTs) are fabricated using densely aligned arrays of metallic CNTs (m-CNTs) as source and drain electrodes, and aligned arrays of semiconducting enriched CNTs (s-CNTs) as channel material. The electrical transport measurements at room temperature show that the m-CNT contacted s-CNT array devices with a 2 um channel length perform superiorly to those of control Pd contacted s-CNT devices. The m-CNT contacted devices exhibit a maximum (average) on-conductance of 36.5 uS (19.2 uS), transconductance of 2…
We report on efficient spin injection in p-doped InGaAs/GaAs quantum-dot (QD) spin light emitting diode (spin-LED) under zero applied magnetic field. A high degree of electroluminescence circular polarization (Pc) ~19% is measured in remanence up to 100K. This result is obtained thanks to the combination of a perpendicularly magnetized CoFeB/MgO spin injector allowing efficient spin injection and an appropriate p-doped InGaAs/GaAs QD layer in the active region. By analyzing the bias and temperature dependence of the electroluminescence circular polarization, we have evidenced a two-step spin r…
We demonstrate electrical spin injection into multilayer graphene (MLG) in a lateral spin valve device from a highly spin-polarized Co2FeSi (CFS) Huesler electrode. Exfoliated MLG was transferred onto pre-patterned epitaxial CFS wires grown on an Si(111) substrate by a polymer-based transfer method. This method enabled us to fabricate multiple single-crystal CFS electrodes in contact with MLG. Electrical spin injection from CFS to MLG was detected through non-local magnetoresistance (MR) measurement. A non-local spin signal of 430 ohm was observed; this is the largest value among all reported …
We achieve tunneling spin injection from Co into single layer graphene (SLG) using TiO2 seeded MgO barriers. A non-local magnetoresistance (ΔRNL) of 130 Ω is observed at room temperature, which is the largest value observed in any material. Investigating ΔRNL vs. SLG conductivity from the transparent to the tunneling contact regimes demonstrates the contrasting behaviors predicted by the drift-diffusion theory of spin transport. Furthermore, tunnel barriers reduce the contact-induced spin relaxation and are therefore important for future investigations of spin relaxation in graphene.
We achieve tunneling spin injection from Co into single layer graphene (SLG) using TiO2 seeded MgO barriers. A non-local magnetoresistance (ΔRNL) of 130 Ω is observed at room temperature, which is the largest value observed in any material. Investigating ΔRNL vs. SLG conductivity from the transparent to the tunneling contact regimes demonstrates the contrasting behaviors predicted by the drift-diffusion theory of spin transport. Furthermore, tunnel barriers reduce the contact-induced spin relaxation and are therefore important for future investigations of spin relaxation in graphene.
We propose an unconventional type of Hall effect in a topological Dirac semimetal with ferromagnetic electrodes. The topological Dirac semimetal itself has time-reversal symmetry, whereas attached ferromagnetic electrodes break it, causing the large Hall response. This induced Hall effect is a characteristic of the helical surface/edge states that arise in topological materials, such as topological Dirac semimetals or quantum spin Hall insulators. We compute the Hall conductance/resistance and the Hall angle by using a lattice model with four-terminal geometry. For topological Dirac semimetals…
The outstanding electrical and optical properties of graphene make it an excellent alternative as a transparent electrode. Here we demonstrate the application of graphene as collector material in internal photoemission (IPE) spectroscopy; enabling the direct observation of both electron and hole injections at a Si/Al2O3 interface and successfully overcoming the long-standing difficulty of detecting holes injected from a semiconductor emitter in IPE measurements. The observed electron and hole barrier heights are 3.5 eV and 4.1 eV, respectively. Thus the bandgap of Al2O3 can be further deduced …
Spintronics is an analogue to electronics where spin of the electron rather than its charge is functionally controlled for devices. The generation and detection of spin current without ferromagnetic or exotic/scarce materials are two the biggest challenges for spintronics devices. In this study, we report a solution to the two problems of spin current generation and detection in Si. Using non-local measurement, we experimentally demonstrate the generation of helical dissipationless spin current using spin-Hall effect. Contrary to the theoretical prediction, we observe the spin-Hall effect in b…
Spin accumulation induced in p-type germanium from Fe/MgO tunnel contacts is studied as a function of hole concentration p (10^16 - 10^19 cm-3). For all p, the contacts are free of rectification and Schottky barrier, guaranteeing spin injection into the Ge and preventing spin accumulation enhancement by two-step tunneling via interface states. The observed spin accumulation is smallest for nondegenerate doping (p ~ 10^16 cm-3) and increases for heavily doped Ge. This trend is opposite to what is expected from spin injection and diffusion theory. For heavily doped Ge, the observed spin accumula…
Spin-resolved electron symmetry filtering is a key mechanism behind giant tunneling magnetoresistance (TMR) in Fe/MgO/Fe and similar magnetic tunnel junctions (MTJs), providing room temperature functionality in modern spin electronics. However, the core process of the electron symmetry filtering breaks down under applied bias, dramatically reducing the TMR above 0.5 V. This strongly hampers the application range of MTJs. To circumvent the problem, resonant tunneling between ferromagnetic electrodes through quantum well states in thin layers has been used so far. This mechanism, however, is mai…
We performed measurements of Py/Cu and Py/Ag lateral spin valves as function of injection current direction and magnitude. Above a 'critical' current, there is an unexpected dependence of spin injection on current direction. Positive currents show higher polarization of spin injection than negative. This implies that in addition to current-induced spin injection, there is a thermally induced injection from a spin-dependent Seebeck effect. A temperature gradient in the Py electrode, caused by Joule heating, is responsible for injecting excess spins into the non-magnetic channel. This effect has…
Employing first-principles calculations, we investigate efficiency of spin injection from a ferromagnetic (FM) electrode (Ni) into graphene and possible enhancement by using a barrier between the electrode and graphene. Three types of barriers, h-BN, Cu(111), and graphite, of various thickness (0-3 layers) are considered and the electrically biased conductance of the Ni/Barrier/Graphene junction are calculated. It is found that the minority spin transport channel of graphene can be strongly suppressed by the insulating h-BN barrier, resulting in a high spin injection efficiency. On the other h…
Cryogenic-temperature Grain-to-grain Epitaxial Growth of High-quality Ultrathin CoFe Layer on MgO Tunnel Barrier for High-performance Magnetic Tunnel Junctions
We demonstrate fully electrical detection of spin injection in InAs quantum wells. A spin polarized current is injected from a NiFe thin film to a two-dimensional electron gas (2DEG) made of InAs based epitaxial multi-layers. Injected spins accumulate and diffuse out in the 2DEG, and the spins are electrically detected by a neighboring NiFe electrode. The observed spin diffusion length is 1.8 um at 20 K. The injected spin polarization across the NiFe/InAs interface is 1.9% at 20 K and remains at 1.4% even at room temperature. Our experimental results will contribute significantly to the realiz…
We report on first-principles calculations of spin-transfer torque (STT) in epitaxial magnetic tunnel junctions (MTJs) based on ferrimagnetic tetragonal Mn$_3$Ga electrodes, both as analyzer in an Fe/MgO stack, and also in an analogous stack with a second Mn$_3$Ga electrode (instead of Fe) as polarizer. Solving the ballistic transport problem (NEGF + DFT) for the nonequilibrium spin density in a scattering region extended to over 7.6 nm into the Mn$_3$Ga electrode, we find long-range spatial oscillations of the STT decaying on a length scale of a few tens of angstroms, both in the linear respo…
