We derive an analytic formula for the elastic bending modulus of single-layer black phosphorus (SLBP) based on the valence force field model. The obtained elastic bending modulus is 4.8028 eV and 7.9905 eV along the armchair and zigzag directions in the SLBP, respectively. These values are obviously larger than the bending modulus of 1.4 eV in graphene due to the intrinsic finite thickness for SLBP. Our derivation analytically illustrates that the elastic bending modulus of the SLBP is proportional to the square of the intrinsic thickness of the SLBP.
We derive an analytic formula for the Young's modulus in single-layer black phosphorus using the valence force field model. By analyzing the directional dependence for the Young's modulus, we explore the third principle direction with direction angle phi_tp = 0.268pi besides armchair and zigzag directions. The maximum Young's modulus value is in the third principle direction. More specifically, the Young's modulus is 52.2 N/m, 85.4 N/m, and 111.4 N/m in the armchair direction, zigzag direction, and the third principle direction, respectively. This new principle direction is of significance for…
The distinguishing structural feature of single-layer black phosphorus is its puckered structure, which leads to many novel physical properties. In this work, we first present a new parameterization of the Stillinger-Weber potential for single-layer black phosphorus. In doing so, we reveal the importance of a cross-pucker interaction term in capturing its unique mechanical properties, such as a negative Poisson's ratio. In particular, we show that the cross-pucker interaction enables the pucker to act as a re-entrant hinge, which expands in the lateral direction when it is stretched in the lon…
We derive, from an empirical interaction potential, an analytic formula for the elastic bending modulus of single-layer MoS2 (SLMoS2). By using this approach, we do not need to define or estimate a thickness value for SLMoS2, which is important due to the substantial controversy in defining this value for two-dimensional or ultrathin nanostructures such as graphene and nanotubes. The obtained elastic bending modulus of 9.61 eV in SLMoS2 is significantly higher than the bending modulus of 1.4 eV in graphene, and is found to be within the range of values that are obtained using thin shell theory…
The mechanical properties of single-layer black phosphrous under uniaxial deformation are investigated using first-principles calculations. Both Young's modulus and the ultimate strain are found to be highly anisotropic and nonlinear as a result of its quasi-two-dimensional puckered structure. Specifically, the in-plane Young's modulus is 44.0 GPa in the direction perpendicular to the pucker, and 92.7 GPa in the parallel direction. The ultimate strain is 0.48 and 0.20 in the perpendicular and parallel directions, respectively.
Black phosphorus is a quasi-two-dimensional layered semiconductor with a narrow direct band gap of 0.3 eV. A giant surface Stark effect can be produced by the potassium doping of black phosphorus, leading to a semiconductor to semimetal phase transition originating from the creation of a strong surface dipole and associated band bending. By using time- and angle-resolved photoemission spectroscopy, we report the partial photoinduced screening of this band bending by the creation of a compensating surface photovoltage. We further resolve the detailed dynamics of this effect at the pertinent tim…
The structural and elastic properties of orthorhombic black phosphorus have been investigated using first-principles calculations based on density functional theory. The structural parameters have been calculated using the local density approximation (LDA), the generalized gradient approximation (GGA), and with several dispersion corrections to include van der Waals interactions. It is found that the dispersion corrections improve the lattice parameters over LDA and GGA in comparison with experimental results. The calculations reproduce well the experimental trends under pressure and show that…
The single-layer black phosphorus is characteristic for its puckered configuration that possesses the hinge-like mechanism, which leads to the highly anisotropic in-plane Poisson's ratios and the negative out-of-plane Poisson's ratio. We reveal that the hinge-like mechanism can be attributed to the angle-angle cross interaction, which, combined with the bond stretching and angle bending interactions, is able to provide a good description of the mechanical properties in the single-layer black phosphorus. We also propose a nonlinear angle-angle cross interaction, which follows the form of the St…
Recently fabricated two dimensional (2D) phosphorene crystal structures have demonstrated great potential in applications of electronics. Mechanical strain was demonstrated to be able to significantly modify the electronic properties of phosphorene and few-layer black phosphorus. In this work, we employed first principles density functional theory calculations to explore the mechanical properties of phosphorene, including ideal tensile strength and critical strain. It was found that a monolayer phosphorene can sustain tensile strain up to 27% and 30% in the zigzag and armchair directions, resp…
The allotropes of a new layered material, phosphorus carbide (PC), have been predicted recently and a few of these predicted structures have already been successfully fabricated. Herein, by using first-principles calculations we investigated the effects of rippling a PC monolayer, one of the most stable modifications of layered PC, under large compressive strains. Similar to phosphorene, layered PC was found to have the extraordinary ability to bend and form ripples with large curvatures under a sufficiently large strain applied along its armchair direction. The band gap size, workfunction, an…
Black phosphorus (BP) has emerged as a promising candidate for next generation electronics and optoelectronics among the 2D family materials due to its extraordinary electrical/optical/optoelectronic properties. Interestingly, BP shows strong anisotropic transport behaviour because of its puckered honeycomb structure. Previous studies have demonstrated the thermal transport anisotropy of BP and theoretically attribute this to the anisotropy in both phonon dispersion relation and phonon relaxation time. However, the exact origin of such strong anisotropy lacks clarity and has yet to be proven e…
It is of critical importance to understand the mechanical properties change of electrode materials during lithium intercalation in the mechanical design of Li-ion batteries, for the purpose of the high reliability and safety in their applications. Here, we investigated the mechanical properties of both bulk and single layer phosphorus during the lithium intercalation process by using the first-principles calculations. Our results show that the Young's modulus of bulk and layered phosphorus strongly depends on the lithium intercalation. The mechanical bearing capacities, such as critical strain…
Young's modulus determines the mechanical loads required to elastically stretch a material, and also, the loads required to bend it, given that bending stretches one surface while compressing the opposite one. Flexoelectric materials have the additional property of becoming electrically polarized when bent. While numerous studies have characterized this flexoelectric coupling, its impact on the mechanical response, due to the energy cost of polarization upon bending, is largely unexplored. This intriguing contribution of strain gradient elasticity is expected to become visible at small length …
We report on the mechanical properties of few-layer black phosphorus (BP) nanosheets, in high vacuum and as a function of time of exposure to atmospheric conditions [1]. BP flakes with thicknesses ranging from 4 to 30 nm suspended over circular holes are characterized by nanoindentations using an atomic force microscope tip. From measurements in high vacuum an elastic modulus of 46+/-10 GPa and breaking strength of 2.4+/-1 GPa are estimated. Both magnitudes are independent of the thickness of the flakes. Our results show that the exposure to air has substantial influence in the mechanical resp…
We study the bending of rectangular atomic monolayers along different directions from first principles. Specifically, choosing the phosphorene, GeS, TiS$_3$, and As$_2$S$_3$ monolayers as representative examples, we perform Kohn-Sham density functional theory calculations to determine the variation in transverse flexoelectric coefficient and bending modulus with the direction of bending. We find that while the flexoelectric coefficient is nearly isotropic, there is significant and complex anisotropy in bending modulus that also differs between the monolayers, with extremal values not necessari…
We demonstrate the large scale exfoliation of bulk black phosphorus into few-layers black phosphorus. We use wet-jet mill (WJM) as an industrially scalable exfoliation technique. In order to avoid the degradation by oxidation of the exfoliated flakes, the few-layers black phosphorus is protected by functionalisation (with 4-bromobenzene-diazonium tetrafluoroborate) during the exfoliation process. We used the exfoliated and functionalised flakes as fillers in a polymethyl methacrylate matrix to test the mechanical endurance, obtaining an improvement in the Young modulus of 106% compared to the …
Amorphous materials exhibit peculiar mechanical and vibrational properties, including non-affine elastic responses and excess vibrational states, i.e., the so-called boson peak. For polymer glasses, these properties are considered to be affected by the bending rigidity of the constituent polymer chains. In our recent work [Tomoshige, et al., Sci. Rep. 9 19514 (2019)], we have revealed simple relationships between the variations of vibrational properties and the global elastic properties: the response of the boson peak scales only with that of the global shear modulus. This observation suggests…
When a two-dimensional material, adhered onto a compliant substrate, is subjected to compression it can undertake a buckling instability yielding to a periodic rippling. Interestingly, when black phosphorus flakes are compressed along the zig-zag crystal direction the flake buckles forming ripples with a 40% longer period than that obtained when the compression is applied along the armchair direction. This anisotropic buckling stems from the puckered honeycomb crystal structure of black phosphorus and a quantitative analysis of the ripple period allows us to determine the Youngs's modulus of f…
Black phosphorous (BP) is a layered semiconductor with high carrier mobility, anisotropic optical response and wide bandgap tunability. In view of its application in optoelectronic devices, understanding transient photo-induced effects is crucial. Here, we investigate by time- and angle-resolved photoemission spectroscopy BP in its pristine state and in the presence of Stark splitting, chemically induced by Cs ad-sorption. We show that photo-injected carriers trigger bandgap renormalization and a concurrent valence band attening caused by Pauli blocking. In the biased sample, photoexcitation l…
A numerical study on the elastic response of single- and multi-layer systems formed by alternating pentamode lattices and stiffening plates is presented. Finite element simulations are conducted to analyze the dependence of the effective elastic moduli of such structures upon suitable aspect ratios, which characterize the geometry of the generic pentamode layer at the micro- and macro-scale, and the lamination scheme of the layered structure. The given numerical results highlight that the examined structures exhibit bending-dominated response, and are able to achieve low values of the effectiv…
We systematically investigated the geometric, electronic and thermoelectric (TE) properties of bulk black phosphorus (BP) under strain. The hinge-like structure of BP brings unusual mechanical responses such as anisotropic Young's modulus and negative Poisson's ratio. A sensitive electronic structure of BP makes it transform among metal, direct and indirect semiconductors under strain. The maximal figure of merit $ZT$ of BP is found to be 0.72 at $800\,\mathrm{K}$ that could be enhanced to 0.87 by exerting an appropriate strain, revealing BP could be a potential medium-high temperature TE mate…
In many applications, viscoelastic properties of reinforced composites need to be determined prior to their real service life. Such properties can be assured by destructive and non-destructive tests. In this paper, a novel non-destructive test (NDT) method based on flexural free vibration is introduced to investigate the viscoelastic properties of fiber-reinforced composites. Three different types of industrial fibers (carbon, glass, and hemp) and an unsaturated polyester resin were selected to produce bar-shaped composites via pultrusion technique. These composite bars were used in a simple N…
Bond stretching and angle bending force fields, appropriate to describe in-plane motion of graphene sheets, are derived using first principles' methods. The obtained force fields are fitted by analytical anharmonic energy potential functions, providing efficient means of calculations in molecular mechanics simulations. Numerical results regarding the mechanical behavior of graphene monolayers under various loads, like uniaxial tension, hydrostatic tension, and shear stress, are presented, using both molecular dynamics simulations and first principles' methods. Stress-strain curves and elastic …
Herein, we performed first principle calculation and classical molecular dynamics simulation to study structural optimization, band structure, and mechanical properties of differently stacked multilayer silicene. Several local energy minima have been identified as metastable conformation with different stacking mode and layer number. Bandstructure of low buckled AA bilayer silicene optimized with SCAN+rvv10 presents semiconducting behavior with a bandgap of 0.4419ev. Young's modulus of multilayer silicene shows low dependency on layer number or stacking mode. Whereas, fracture stress and strai…
. A kind of "Elastic Composite, Reinforced Lightweight Concrete (ECRLC)" with the mentioned specifics is a type of "Resilient Composite Systems (RCS)" in which, contrary to the basic geometrical assumption of flexure theory in Solid Mechanics, "the strain changes in the beam height during bending" is typically "Non-linear". . Through employing this integrated structure, with significant high strain capability and modulus of resilience in bending, we could constructively achieve high bearing capacities in beams with secure fracture pattern, in less weight. . Due to the system particulars and it…
A panoptic view of architectured planar lattices based on star-polygon tilings was developed. Four star-polygon-based lattice sub-families, formed of systematically arranged triangles, squares, or hexagons, were investigated numerically and experimentally. Finite-element-based homogenization allowed computation of Poisson's ratio, elastic modulus, shear modulus, and planar bulk modulus. A comprehensive understanding of the range of properties and micromechanical deformation mechanisms was developed. Adjusting the star-polygon angle achieved an over 250-fold range in elastic modulus, over a 10-…
We have studied the elastic deformation of freely suspended atomically thin sheets of muscovite mica, a widely used electrical insulator in its bulk form. Using an atomic force microscope, we carried out bending test experiments to determine the Young's modulus and the initial pre-tension of mica nanosheets with thicknesses ranging from 14 layers down to just one bilayer. We found that their Young's modulus is high (190 GPa), in agreement with the bulk value, which indicates that the exfoliation procedure employed to fabricate these nanolayers does not introduce a noticeable amount of defects.…
We study the elastic deformation of few layers (5 to 25) thick freely suspended MoS2 nanosheets by means of a nanoscopic version of a bending test experiment, carried out with the tip of an atomic force microscope. The Young's modulus of these nanosheets is extremely high (E = 0.33 TPa), comparable to that of graphene oxide, and the deflections are reversible up to tens of nanometers.
