Large eddy simulations of wind farms are performed to study the effects of wind turbine row alignment with respect to the incoming flow direction. Various wind farms with fixed stream-wise spacing (7.85 rotor diameters) and varying lateral displacements and span-wise turbine spacings are considered, for a fixed inflow direction. Simulations show that, contrary to common belief, a perfectly staggered (checker-board) configuration does not necessarily give the highest average power output. Instead, the highest mean wind farm power output is found to depend on several factors, the most important one being the alignment that leads to minimization of wake effects from turbines in several upstream rows. This alignment typically occurs at significantly smaller angles than those corresponding to perfect staggering. The observed trends have implications for wind farm designs, especially in sites with a well-defined prevailing wind direction.
In large eddy simulation of atmospheric boundary layer flows over wind farms, wall-layer models are generally imposed for the surface fluxes without considering the spatial variability of the surface roughness. In this study, we consider the near-surface model in conjunction with square of the velocity gradient tensor to model the adaptive dissipation of turbulence production. The surface roughness is incorporated through Monin-Obhukhov similarity theory for the computational cells immediately adjacent to the Earth's surface. The underlying proposed near-surface model captures the significant …
Numerous studies have shown that wind turbine wakes within a large wind farm bring about changes to both the dynamics and thermodynamics of the atmospheric boundary layers (ABL). Previously, we investigated the relative humidity budget within a wind farm via field measurements in the near-wake region and large eddy simulations (LES). The effect of the compounding wakes within a large wind farm on the relative humidity was also investigated by LES. In this study, we investigate how the areas of relative humidity variation, that was observed in the near-wake, develop downstream in the shadow reg…
In large wind farms, wake distribution behind a wind turbine causes a considerable reduction of wind velocity for downstream wind turbines, resulting in a significant amount of power loss. Therefore, it is very crucial to predict wind turbine wakes efficiently. Thus, we propose a large-eddy simulation (LES) methodology, which takes the vorticity stretching to model transients in wind turbine wakes. In addition, we present an improved actuator disk model, which accounts for two-way feedback between the atmosphere and the wakes. First, we show that the vertical profile of the mean wind predicted…
Fluctuations represent a major challenge for the incorporation of electric power from large wind-farms into power grids. Wind farm power output fluctuates strongly in time, over various time scales. Understanding these fluctuations, especially their spatio-temporal characteristics, is particularly important for the design of backup power systems that must be readily available in conjunction with wind-farms. In this work we analyze the power fluctuations associated with the wind-input variability at scales between minutes to several hours, using large eddy simulations (LES) of extended wind-par…
In order to enable simulations of developing wind turbine array boundary layers with highly realistic inflow conditions a concurrent precursor method for Large Eddy Simulations is proposed. In this method we consider two domains simultaneously, i.e. in one domain a turbulent Atmospheric Boundary Layer (ABL) without wind turbines is simulated in order to generate the turbulent inflow conditions for a second domain in which the wind turbines are placed. The benefit of this approach is that a) it avoids the need for large databases in which the turbulent inflow conditions are stored and the corre…
In recent years, wake steering has been established as a promising method to increase the energy yield of a wind farm. Current practice in estimating the benefit of wake steering on the annual energy production (AEP) consists of evaluating the wind farm with simplified surrogate models, casting a large uncertainty on the estimated benefit. This paper presents a framework for determining the benefit of wake steering on the AEP, incorporating simulation results from a surrogate model and large eddy simulations in order to reduce the uncertainty. Furthermore, a time-varying wind direction is cons…
Large-eddy simulations of the atmospheric boundary layer are often performed using pseudo-spectral methods, which adopt a fringe-region approach to introduce inflow boundary conditions. However, we notice that a standard fringe-region technique excites spurious gravity waves when stratified atmospheres are considered, therefore enhancing the amount of energy reflected from the top of the domain and perturbing the velocity and pressure fields downstream. In this work, we develop a new fringe-region method that imposes the inflow conditions while limiting spurious effects on the surrounding flow…
High-fidelity large-eddy simulations are suitable to obtain insight into the complex flow dynamics in extended wind farms. In order to better understand these flow dynamics, we use dynamic mode decomposition (DMD) to analyze and reconstruct the flow field in large-scale numerically simulated wind farms by large-eddy simulations (LES). Different wind farm layouts are considered, and we find that a combination of horizontal and vertical staggering leads to improved wind farm performance compared to traditional horizontal staggering. We analyze the wind farm flows using the amplitude selection (A…
We present here a computational fluid dynamics (CFD) simulation of Lillgrund offshore wind farm, which is located in the Oresund Strait between Sweden and Denmark. The simulation combines a dynamic representation of wind turbines embedded within a Large-Eddy Simulation CFD solver, and uses hr-adaptive meshing to increase or decrease mesh resolution where required. This allows the resolution of both large scale flow structures around the wind farm, and local flow conditions at individual turbines; consequently, the response of each turbine to local conditions can be modelled, as well as the res…
Recent large eddy simulations have led to improved parameterizations of the effective roughness height of wind farms. This effective roughness height can be used to predict the wind velocity at hub-height as function of the geometric mean of the spanwise and streamwise turbine spacings and the turbine loading factors. Meyers and Meneveau (Wind Energy 15, 305-317 (2012)) used these parameterizations to make predictions for the optimal wind turbine spacing in infinitely large wind farms. They found that for a realistic cost ratio between the turbines and the used land surface the optimal turbine…
The flow speed-up generated by windbreaks can be used to increase the power production of wind turbines. However, due to the increased drag imposed by the windbreaks, their use in large wind turbine arrays has been questioned. We use large eddy simulations to show that windbreaks can increase the power production of large wind farms. A crucial finding is that windbreaks in a wind farm should be much lower than for a single turbine case. In fact, the optimal windbreak for an isolated turbine can reduce wind farm performance. The optimal windbreak height in a wind farm namely depends on the righ…
A simple analysis is presented concerning an upper limit of the power density (power per unit land area) of a very large wind farm located at the bottom of a fully developed boundary layer. The analysis suggests that the limit of the power density is about 0.38 times $τ_{w0}U_{F0}$, where $τ_{w0}$ is the natural shear stress on the ground (that is observed before constructing the wind farm) and $U_{F0}$ is the natural or undisturbed wind speed averaged across the height of the farm to be constructed. Importantly, this implies that the maximum extractable power from such a very large wind farm …
Modern wind farms comprised of horizontal-axis wind turbines (HAWTs) require significant land resources to separate each wind turbine from the adjacent turbine wakes. This aerodynamic constraint limits the amount of power that can be extracted from a given wind farm footprint. The resulting inefficiency of HAWT farms is currently compensated by using taller wind turbines to access greater wind resources at high altitudes, but this solution comes at the expense of higher engineering costs and greater visual, acoustic, radar and environmental impacts. We investigated the use of counter-rotating …
Turbine wake and farm blockage effects may significantly impact the power produced by large wind farms. In this study, we perform Large-Eddy Simulations (LES) of 50 infinitely large offshore wind farms with different turbine layouts and wind directions. The LES results are combined with the two-scale momentum theory (Nishino & Dunstan 2020, J. Fluid Mech. 894, A2) to investigate the aerodynamic performance of large but finite-sized farms as well. The power of infinitely large farms is found to be a strong function of the array density, whereas the power of large finite-sized farms depends on b…
An extended theoretical approach is proposed to predict the average power of wind turbines in a large finite-size wind farm. The approach is based on the two-scale momentum theory proposed recently for the modelling of ideal very large wind farms, but the theory is now generalised by introducing the effect of additional pressure difference induced by the farm between the upstream and downstream sides of the farm, making the approach applicable to real wind farms that are large but not as large as the size of the relevant atmospheric system driving the flow over the farm. To validate the genera…
Wind farm global blockage as an adverse pressure gradient problem: turbulence amplification and spectral modification in the induction region of a model wind farm
The multi-rotor (MR) wind turbine concept can be used to upscale wind turbines without increasing the rotor diameter, which can be beneficial for transport, manufacture and design of wind turbines blades. The rotor interaction of a MR wind turbine leads to a faster wake recovery compared to an equivalent single-rotor (SR) wind turbine wake. In this article, the benefit of the faster wake recovery of MR wind turbines is quantified using Reynolds-averaged Navier-Stokes simulations of a 4x4 rectangular MR wind farm, for three different inter wind turbine spacings. The simulations predict an incre…
We describe a generalization of the Coupled Wake Boundary Layer (CWBL) model for wind-farms that can be used to evaluate the performance of wind-farms under arbitrary wind inflow directions whereas the original CWBL model (Stevens et al., J. Renewable and Sustainable Energy 7, 023115 (2015)) focused on aligned or staggered wind-farms. The generalized CWBL approach combines an analytical Jensen wake model with a "top-down" boundary layer model coupled through an iterative determination of the wake expansion coefficient and an effective wake coverage area for which the velocity at hub-height obt…
This paper solves an approximate form of conservation of mass and momentum for a turbine in a wind farm array. The solution is a fairly simple explicit relationship that predicts the streamwise velocity distribution within a wind farm with an arbitrary layout. As this model is obtained by solving flow governing equations directly for a turbine that is subject to upwind turbine wakes, no ad hoc superposition technique is needed to predict wind farm flows. A suite of large-eddy simulations (LES) of wind farm arrays is used to examine self-similarity as well as validity of the so-called conservat…
While a theoretical limit has long been established for the performance of a single turbine, no corresponding upper bound exists for the power output from a large wind farm, making it difficult to evaluate the available potential for further performance gains. Here we build a model describing the essential features of a large array of turbines with arbitrary design and layout, by considering a fully-developed wind farm whose upper edge is bounded by a self-similar boundary layer. The exchanges between the wind farm, the overlaying boundary layer, and the outer flow are parameterized by means o…
A new theoretical method is presented for future multi-scale aerodynamic optimisation of very large wind farms. The new method combines a recent two-scale coupled momentum analysis of ideal wind turbine arrays with the classical blade-element-momentum (BEM) theory for turbine rotor design, making it possible to explore some potentially important relationships between the design of rotors and their performance in a very large wind farm. The details of the original two-scale momentum model are described first, followed by the new coupling procedure with the classical BEM theory and some example …
A new theoretical approach is proposed to predict a practical upper limit to the efficiency of a very large wind farm. The new theory suggests that the efficiency of ideal turbines in an ideal very large wind farm depends primarily on a non-dimensional parameter $λ/C_{f0}$, where $λ$ is the ratio of the rotor swept area to the land area (for each turbine) and $C_{f0}$ is a natural friction coefficient observed before constructing the farm. When $λ/C_{f0}$ approaches to zero, the new theory goes back to the classical actuator disc theory, yielding the well-known Betz limit. When $λ/C_{f0}$ incr…
Many wind farms are placed near coastal regions or in proximity of orographic obstacles. The meso-scale gradients that develop in these zones make wind farms operating in velocity fields that are rarely uniform. However, all existing wake-merging methods in engineering wind-farm wake models assume a homogeneous background velocity field in and around the farm, relying on a single wind-speed value usually measured several hundreds of meters upstream of the first row of turbines. In this study, we derive a new momentum-conserving wake-merging method capable of superimposing the waked flow on a h…
Co-locating horizontal- and vertical-axis wind turbines has been recently proposed as a possible approach to enhance the land-area power density of wind farms. In this work, we aim to study the benefits associated with such a co-location using large-eddy simulation (LES) and analytical wake models. In this regard, small-scale vertical-axis wind turbines (VAWTs) in triangular clusters are deployed within a finite-size wind farm consisting of horizontal-axis wind turbines (HAWTs). Wake flow within the wind farm and the effect of VAWTs on the overall wind-farm efficiency are investigated and quan…
This paper presents a theory based on the law of momentum conservation to define and help analyse the problem of large wind farm aerodynamics. The theory splits the problem into two sub-problems; namely an 'external' (or farm-scale) problem, which is a time-dependent problem considering large-scale motions of the atmospheric boundary layer (ABL) to assess the amount of momentum available to the ABL's bottom resistance at a certain time; and an 'internal' (or turbine-scale) problem, which is a quasi-steady (in terms of large-scale motions of the ABL) problem describing the breakdown of the ABL'…
The fluid dynamics video No.V058 is introduced, with brief descriptions of the numerical method used to generate the animation data, explanation of what is shown in the movies, and the main scientific findings obtained from this study.
This paper introduces a dynamic parametric wind farm model that is capable of simulating floating wind turbine platform motion coupled with wake transport under time-varying wind conditions. The simulator is named FOWFSim-Dyn as it is a dynamic extension of the previously developed steady-state Floating Offshore Wind Farm Simulator (FOWFSim). One-dimensional momentum conservation is used to model dynamic propagation of wake centerline locations and average velocities, while momentum recovery is approximated with the assumption of a constant temporal wake expansion rate. Platform dynamics are c…
We present results from large eddy simulations (LES) of extended wind-farms for several turbine configurations with a range of different spanwise and streamwise spacing combinations. The results show that for wind-farms arranged in a staggered configuration with spanwise spacings in the range $\approx[3.5,8]$D, where $D$ is the turbine diameter, the power output in the fully developed regime depends primarily on the geometric mean of the spanwise and streamwise turbine spacings. In contrast, for the aligned configuration the power output in the fully developed regime strongly depends on the st…
Turbine wake and local blockage effects are known to alter wind farm power production in two different ways: (1) by changing the wind speed locally in front of each turbine; and (2) by changing the overall flow resistance in the farm and thus the so-called farm blockage effect. To better predict these effects with low computational costs, we develop data-driven emulators of the `local' or `internal' turbine thrust coefficient $C_T^*$ as a function of turbine layout. We train the model using a multi-fidelity Gaussian Process (GP) regression with a combination of low (engineering wake model) and…
Reynolds-averaged Navier-Stokes (RANS) is one of the most cost-efficient approaches to simulate wind-farm-atmosphere interactions. However, the applicability of RANS-based methods is always limited by the accuracy of turbulence closure models, which introduce various uncertainties into the models. In this study, we estimate model-form uncertainties in RANS simulations of wind farms. For this purpose, we compare different RANS models to a large-eddy simulation (LES). We find that the realizable k-epsilon model is a representative RANS model for predicting the mean velocity, the turbulence inten…
We generate explicit height-dependent eddy viscosity coefficients in the Ekman layer from convex wind speed profiles. The solutions we obtain are parameterized in terms of the relative deflection angle between the wind directions at the top and bottom of the flow, as well as the geostrophic wind speed and a velocity scale we interpret as the transfer rate of horizontal momentum in the vertical direction. The solutions may be used to infer the thickness of the Ekman layer for a variety of deflection angles different from deflection angle of the classic Ekman spiral.
Low-level jets (LLJs) are the wind maxima in the lower regions of the atmosphere with a high wind energy potential. Here we use large-eddy simulations to study the effect of LLJ height on the flow dynamics in a wind farm with $10\times4$ turbines. We change the LLJ height and atmospheric thermal stratification by varying the surface cooling rate. We find that the first row power production is higher in the presence of a LLJ compared to a neutral reference case without LLJ. Besides, we show that the first row power production increases with decreasing LLJ height. Due to the higher turbulence in…
Computational fluid dynamics using the Reynolds-averaged Navier-Stokes (RANS) remains the most cost-effective approach to study wake flows and power losses in wind farms. The underlying assumptions associated with turbulence closures are one of the biggest sources of errors and uncertainties in the model predictions. This work aims to quantify model-form uncertainties in RANS simulations of wind farms at high Reynolds numbers under neutrally stratified conditions by perturbing the Reynolds stress tensor through a data-driven machine-learning technique. To this end, a two-step feature-selection…
As a generalization of the mass-flux based classical stream-tube, the concept of momentum and energy transport tubes is discussed as a flow visualization tool. These transport tubes have the property, respectively, that no fluxes of momentum or energy exist over their respective tube mantles. As an example application using data from large-eddy simulation, such tubes are visualized for the mean-flow structure of turbulent flow in large wind farms, in fully developed wind-turbine-array boundary layers. The three-dimensional organization of energy transport tubes changes considerably when turbin…
We present and test the coupled wake boundary layer (CWBL) model that describes the distribution of the power output in a wind-farm. The model couples the traditional, industry-standard wake model approach with a "top-down" model for the overall wind-farm boundary layer structure. This wake model captures the effect of turbine positioning, while the "top-down" portion of the model adds the interactions between the wind-turbine wakes and the atmospheric boundary layer. Each portion of the model requires specification of a parameter that is not known a-priori. For the wake model, the wake expans…
Low-level jets (LLJs) are the wind maxima in the lowest 50 to 1000 m of atmospheric boundary layers. Due to their significant influence on the power production of wind farms it is crucial to understand the interaction between LLJs and wind farms. In the presence of an LLJ, there are positive and negative shear regions in the velocity profile. The positive shear regions of LLJs are continuously turbulent, while the negative shear regions have limited turbulence. We present large-eddy simulations of wind farms in which the LLJ is above, below, or in the middle of the turbine rotor swept area. We…
The expected growth in wind energy capacity requires efficient and accurate models for wind farm layout optimization, control, and annual energy predictions. Although analytical wake models are widely used for these applications, several model components must be better understood to improve their accuracy. To this end, we propose a Bayesian uncertainty quantification framework for physics-guided data-driven model enhancement. The framework incorporates turbulence-related aleatoric uncertainty in historical wind farm data, epistemic uncertainty in the empirical parameters, and systematic uncert…
The power output of wind farms depends strongly on spatial turbine arrangement, and the resulting turbulent interactions with the atmospheric boundary layer. The main goal of this work is to study the effect of turbine layout on the power output for large wind farms approaching a fully-developed regime. For this purpose we employ an experimental setup of a scaled wind farm with one-hundred porous disk models, of which sixty are instrumented with strain gages. Our experiments cover a parametric space of fifty-six different layouts for which the turbine-area-density is constant, focusing on diff…
We introduce a gradient-free data-driven framework for optimizing the power output of a wind farm based on a Bayesian approach and large-eddy simulations. In contrast with conventional wind farm layout optimization strategies, which make use of simple wake models, the proposed framework accounts for complex flow phenomena such as wake meandering, local speed-ups and the interaction of the wind turbines with the atmospheric flow. The capabilities of the framework are demonstrated for the case of a small wind farm consisting of five wind turbines. It is shown that it can find optimal designs wit…
