Understanding ELM mitigation by resonant magnetic perturbations on MAST
A. Kirk, I. T. Chapman, Yueqiang Liu, P. Cahyna, P. Denner, G. Fishpool, C. J. Ham, J. R. Harrison, Yunfeng Liang, E. Nardon, S. Saarelma, R. Scannell, A. J. Th… 展开作者
A. Kirk, I. T. Chapman, Yueqiang Liu, P. Cahyna, P. Denner, G. Fishpool, C. J. Ham, J. R. Harrison, Yunfeng Liang, E. Nardon, S. Saarelma, R. Scannell, A. J. Thornton, the MAST team
备注：
41 pages, 19 figures. arXiv admin note: text overlap with arXiv:1305.3061
Sustained ELM mitigation has been achieved using RMPs with a toroidal mode number of n=4 and n=6 in lower single null and with n=3 in connected double null plasmas on MAST. The ELM frequency increases by up to a factor of eight with a similar reduction in ELM energy loss. A threshold current for ELM mitigation is observed above which the ELM frequency increases approximately linearly with current in the coils. A comparison of the filament structures observed during the ELMs in the natural and mitigated stages shows that the mitigated ELMs have the characteristics of type I ELMs even though their frequency is higher, their energy loss is reduced and the pedestal pressure gradient is decreased. During the ELM mitigated stage clear lobe structures are observed in visible-light imaging of the X-point region. The size of these lobes is correlated with the increase in ELM frequency observed. The RMPs produce a clear 3D distortion to the plasma and it is likely that these distortions explain why ELMs are destabilised and hence why ELM mitigation occurs.
The interaction between Edge Localized Modes (ELMs) and Resonant Magnetic Perturbations (RMPs) is modeled with the magnetohydrodynamic code JOREK using experimental parameters from ASDEX Upgrade discharges. The ELM mitigation or suppression is optimal when the amplification of both tearing and peeling-kink responses result in a better RMP penetration. The ELM mitigation or suppression is not only due to the reduction of the pressure gradient, but predominantly arises from the toroidal coupling between the ELMs and the RMP-induced mode at the plasma edge, forcing the edge modes to saturate at a…
Pedestal profiles that span the ELM cycle have been obtained and used to test the idea that the pedestal pressure gradient in MAST is limited by the onset of Kinetic Ballooning Modes (KBMs). During the inter-ELM period of a regularly type I ELM-ing discharge on MAST, the pressure pedestal height and width increase together while the pressure gradient increases by only 15 % during the ELM cycle. Stability analyses show that the pedestal region over which infinite-n ballooning modes are unstable also broadens during the ELM cycle. To test the relationship between the width of the region that is …
The application of resonant magnetic perturbations (RMPs) produces splitting of the divertor strike point due to the interaction of the RMP field and the plasma field. The application of a rotating RMP field causes the strike point splitting to rotate, distributing the particle and heat flux evenly over the divertor. The RMP coils in MAST have been used to generate a rotating perturbation with a toroidal mode number n=3. The ELM frequency is doubled with the application of the RMP rotating field, whilst maintaining the H mode. During mitigation, the ELM peak heat flux is seen to be reduced by …
Edge localised modes (ELMs) are a concern for future devices as they can limit the operational lifetime of the divertor. The mitigation of ELMs can be performed by the application of resonant magnetic perturbations (RMPs) which act to degrade the pressure gradient in the edge of the plasma. Investigations of the effect of RMPs on MAST have been performed in a range of plasmas using perturbations with toroidal mode numbers of n=3, 4 and 6. It has been seen that the RMPs increase the ELM frequency, which gives rise to a corresponding decrease in the ELM energy. The reduced ELM energy decreases t…
Shallow fuelling pellets are injected from the high field side into plasmas in which ELMs have been mitigated using external magnetic perturbation coils. The data are compared with ideal assumptions in the ITER fuelling model, namely that mitigated ELMs are not affected by fuelling pellets. Firstly it is shown that during the pellet evaporation an ELM is triggered, during which the amount particle loss could be larger (factor ~1.5) than the particle loss during an ELM which was not induced by pellet. Secondly, a favourable example is shown in which post-pellet particle losses due to mitigated …
The application of resonant magnetic perturbations (RMPs) with a toroidal mode number of n=3 to connected double null plasmas in the MAST tokamak produces up to a factor of 9 increase in Edge Localized Mode (ELM) frequency and reduction in plasma energy loss associated with type-I ELMs. A threshold current for ELM mitigation is observed above which the ELM frequency increases approximately linearly with current in the coils. The effect of the RMPs is found to be scenario dependent. In one scenario the mitigation is only due to a large density pump out event and if the density is recovered by g…
The application of resonant magnetic perturbations (RMPs) with a toroidal mode number of n=4 or n=6 to lower single null plasmas in the MAST tokamak produces up to a factor of 5 increase in Edge Localized Mode (ELM) frequency and reduction in plasma energy loss associated with type-I ELMs. A threshold current for ELM mitigation is observed above which the ELM frequency increases approximately linearly with current in the coils. Despite a large scan of parameters, complete ELM suppression has not been achieved. The results have been compared to modelling performed using either the vacuum approx…
The complete refuelling of the plasma density loss (pump-out) caused by mitigation of Edge Localised Modes (ELMs) is demonstrated on the ASDEX Upgrade tokamak. The plasma is refuelled by injection of frozen deuterium pellets and ELMs are mitigated by external resonant magnetic perturbations (RMPs). In this experiment relevant dimensionless parameters, such as relative pellet size, relative RMP amplitude and pedestal collisionality are kept at the ITER like values. Refuelling of density pump out requires a factor of two increase of nominal fuelling rate. Energy confinement and pedestal temperat…
The fuelling of plasmas by shallow frozen pellets with simultaneous mitigation of edge localised modes (ELM) by external magnetic perturbation is demonstrated on the MAST tokamak. Post-pellet particle loss is dominated by ELMs and inter-ELM gas fuelling. It is shown that the size of post-pellet ELMs can be controlled by external magnetic perturbations. Post-pellet ELMs remove particles from the large part of pellet deposition zone including the area with positive density gradient. The mechanism explaining this peculiarity of particle loss is suggested.
In future nuclear fusion reactors high heat load events, such as edge-localised modes (ELMs), can potentially damage divertor materials and release impurities into the main plasma, limiting plasma performance. The most difficult to handle are type I ELMs since they carry the largest fraction of energy from the plasma and therefore deposit the largest heat flux at the target and on first wall materials. Knowing the temperature of the ions released from ELM events is important since it determines the potential sputtering they would cause from plasma facing materials. To make measurements of Ti b…
Ion energy measurements have been made in the scrape off layer of the Mega Amp Spherical Tokamak (MAST) using a midplane retarding field energy analyser (RFEA) in H-mode plasmas during the inter-edge localised mode (ELM) period and during type I and type III ELMs. During the inter-ELM period at distances of 3 to 8 cm from the last closed flux surface (LCFS), ion temperatures of 20 to 70 eV have been measured giving an ion to electron temperature ratio of 2 to 7 with a mean of 4. During type III ELMs, an ion temperature of 50 eV has been measured 3 to 6 cm from the LCFS which decreases to 30 eV…
Type-I Edge Localised Modes (ELMs) have been mitigated in MAST through the application of n = 3, 4 and 6 resonant magnetic perturbations (RMPs). For each toroidal mode number of the non-axisymmetric applied fields, the frequency of the ELMs has been increased significantly, and the peak heat flux on the divertor plates reduced commensurately. This increase in ELM frequency occurs despite a significant drop in the edge pressure gradient, which would be expected to stabilise the peeling-ballooning modes thought to be responsible for type-I ELMs. Various mechanisms which could cause a destabilisa…
The power load to the divertor surfaces is a key concern for future devices such as ITER, due to the thermal limits on the material surface. One factor that characterizes the heat flux to the divertor is the fall off length in the scrape-off layer (SOL), which recent empirical scalings have shown could be as small as 1 mm. These predictions are based on a multi-machine scaling of the heat flux width fitted using an expression for the divertor heat flux profile which includes a term for the exponential decay in the SOL and diffusion about the last closed flux surface (LCFS) in the private flux …
Edge localised modes (ELMs) are a concern for future devices, such as ITER, due to the large transient heat loads they generate on the divertor surfaces which could limit the operational time of the device. This paper discusses the application of resonant magnetic perturbations (RMPs) as a mechanism for ELM control on MAST. Experiments have been performed using an n=3 toroidal mode number perturbation and measurements of the strike point splitting performed. The measurements have been made using both infrared and visible imaging to measure the heat and particle flux to the divertor. The measur…
The effect of ASDEX Upgrade (AUG) ELM mitigation coils on fast ion wall loads was studied with the fast particle following Monte Carlo code ASCOT. Neutral beam injected (NBI) particles were simulated in two AUG discharges both in the presence and in the absence of the magnetic field perturbation induced by the eight newly installed in-vessel coils. In one of the discharges (#26476) beams were applied individually, making it a useful basis for investigating the effect of the coils on different beams. However, no ELM mitigation was observed in #26476, probably due to the low plasma density. Ther…
The distribution of particles and power to plasma-facing components is of key importance in the design of next-generation fusion devices. Power and particle decay lengths have been measured in a number of MAST L-mode and H-mode discharges in order to determine their parametric dependencies, by fitting power and particle flux profiles measured by divertor Langmuir probes, to a convolution of an exponential decay and a Gaussian function. In all discharges analysed, it is found that exponential decay lengths mapped to the midplane are mostly dependent on separatrix electron density and plasma cur…
Sustained ELM mitigation has been achieved on MAST and AUG using RMPs with a range of toroidal mode numbers over a wide region of low to medium collisionality discharges. The ELM energy loss and peak heat loads at the divertor targets have been reduced. The ELM mitigation phase is typically associated with a drop in plasma density and overall stored energy. In one particular scenario on MAST, by carefully adjusting the fuelling it has been possible to counteract the drop in density and to produce plasmas with mitigated ELMs, reduced peak divertor heat flux and with minimal degradation in pedes…
All current estimations of the energy released by type I ELMs indicate that, in order to ensure an adequate lifetime of the divertor targets on ITER, a mechanism is required to decrease the amount of energy released by an ELM, or to eliminate ELMs altogether. One such amelioration mechanism relies on perturbing the magnetic field in the edge plasma region, either leading to more frequent, smaller ELMs (ELM mitigation) or ELM suppression. This technique of Resonant Magnetic Perturbations (RMPs) has been employed to suppress type I ELMs at high collisionality/density on DIII-D, ASDEX Upgrade, KS…
The peak pressure gradient in the pedestal (dPe/dψ) on MAST varies little between edge localized modes (ELMs), although it varies between discharges due factors such as gas fuelling and plasma current. The pressure pedestal width in flux space on the high-field side (HFS), both during the inter-ELM period and amongst different plasma discharges is consistent with a scaling of . In flux space very similar dPe/dψ and Δpe are observed on the HFS and low-field side (LFS) in single null configuration. This symmetry is broken by the application of resonant magnetic perturbations (RMPs). During ELM m…
The application of non-axisymmetric resonant magnetic perturbations (RMPs) with a toroidal mode number n=6 in the MAST tokamak produces a significant reduction in plasma energy loss associated with type-I Edge Localized Modes (ELMs), the first such observation with n>3. During the ELM mitigated stage clear lobe structures are observed in visible-light imaging of the X-point region. These lobes or manifold structures, that were predicted previously, have been observed for the first time in a range of discharges and their appearance is correlated with the effect of RMPs on the plasma i.e. they o…
Resonant magnetic perturbations (RMPs) can mitigate the edge-localized modes (ELMs), i.e. cause a change of the ELM character towards smaller energy loss and higher frequency. During mitigation a change of the spatial structure of ELM loads on divertor was observed on DIII-D and MAST: the power is deposited predominantly in the footprint structures formed by the magnetic perturbation. In the present contribution we develop a theory explaining this effect, based on the idea that part of the ELM loss is caused by parallel transport in the homoclinic tangle formed by the magnetic perturbation of …
Forecasting the first Edge Localized Mode (ELM) after LH-transition with a neural network trained on Doppler Backscattering data from DIII-D
Agency for Science, Technology and Research (A*STAR)（科学技术研究局）；Nanyang Technological University（南洋理工大学）；University of California, Los Angeles（加州大学洛杉矶分校）；Tohoku University（东北大学）
A triggering mechanism responsible for the explosive onset of edge localised modes (ELMs) in fusion plasmas is identified by performing, for the first time, non-linear magnetohydrodynamic simulations of repetitive type-I ELMs. Briefly prior to the ELM crash, destabilising and stabilising terms are affected at different timescales by an increasingly ergodic magnetic field caused by non-linear interactions between the axisymmetric background plasma and growing non-axisymmetric perturbations. The separation of timescales prompts the explosive, i.e. faster than exponential, growth of an ELM crash …
Resonant magnetic perturbations (RMP) have extensively been demonstrated as a plausible technique for mitigating or suppressing large edge localized modes (ELMs). Associated with this is a substantial amount of theory and modelling efforts during recent years. Various models describing the plasma response to the RMP fields have been proposed in the literature, and are briefly reviewed in this work. Despite their simplicity, linear response models can provide alternative criteria, than the vacuum field based criteria, for guiding the choice of the coil configurations to achieve the best control…
It is known that magnetic perturbations can mitigate edge localized modes (ELMs) in experiments, for example MAST (Kirk et al 2013 Nucl. Fusion 53 043007). One hypothesis is that the magnetic perturbations cause a three dimensional corrugation of the plasma and this corrugated plasma has different stability properties to peeling-ballooning modes compared to an axisymmetric plasma. It has been shown in an up-down symmetric plasma that magnetic perturbations in tokamaks will break the usual axisymmetry of the plasma causing three dimensional displacements (Chapman et al 2012 Plasma Phys. Control…
The impact of resonant magnetic perturbations (RMPs) on the power required to access H-mode is examined experimentally on MAST. Applying RMP in n=2,3,4 and 6 configurations causes significant delays to the timing of the L-H transition at low applied fields and prevents the transition at high fields. The experiment was primarily performed at RMP fields sufficient to cause moderate increases in ELM frequency, f mitigated/f natural~3. To obtain H-mode with RMPs at this field, an increase of injected beam power is required of at least 50% for n=3 and n=4 RMP and 100% for n=6 RMP. In terms of power…
In low-collisionality scenarios exhibiting mitigation of edge localized modes (ELMs), stable ideal kink modes at the edge are excited by externally applied magnetic perturbation (MP)-fields. In ASDEX Upgrade these modes can cause three-dimensional (3D) boundary displacements up to the centimeter range. These displacements have been measured using toroidally localized high resolution diagnostics and rigidly rotating n = 2 MP-fields with various applied poloidal mode spectra. These measurements are compared to non-linear 3D ideal magnetohydrodynamics (MHD) equilibria calculated by VMEC. Comprehe…
The free-streaming plus recycling model (FSRM) has recently been developed to understand and predict tungsten gross erosion rates from the divertor during edge localized modes (ELMs). In this work, the FSRM was tested against experimental measurements of W sputtering during ELMs, conducted via fast WI spectroscopy. Good agreement is observed using a variety of controlling techniques, including gas puffing, neutral beam heating, and plasma shaping to modify the pedestal stability boundary and thus the ELM behavior. ELM mitigation by pellet pacing was observed to strongly reduce W sputtering by …
The phenomenon of redistribution of neutral beam fast-ions due to MHD activity in plasma has been observed on many tokamaks and more recently has been a focus of research on MAST (Turnyanskiy M. et al, 2011 Nucl. Fusion 53 053016). n=1 fishbone modes are observed to cause a large decrease in the neutron emission rate corresponding to a significant perturbation of the fast-ion population in the plasma. Theoretical work on fishbone modes states that the fast-ion distribution itself acts as the source of free energy driving the modes that cause the redistribution. Therefore a series of experiment…
