We propose a simple way to improve the laser gravitational-wave detectors sensitivity by means of reduction of the number of reflective coating layers of the core optics mirrors. This effects in the proportional decrease of the coating thermal noise, the most notorious among the interferometers technical noise sources. The price for this is the increased quantum noise, as well as high requirements for the pump laser power and power at the beamsplitter. However, as far as these processes depend differently on the coating thickness, we demonstrate that a certain trade-off is possible, yielding a 20-30% gain (for diverse gravitational wave signal types and interferometer configurations), providing that feasible values of laser power and power on the beamsplitter are assumed.
We have directly observed broadband thermal noise in silica/tantala coatings in a high-sensitivity Fabry-Perot interferometer. Our result agrees well with the prediction based on indirect, ring-down measurements of coating mechanical loss, validating that method as a tool for the development of advanced interferometric gravitational-wave detectors.
The results of measurement of optical mirror coating are presented. These results indicate that Standard Quantum Limit of sensitivity can be reached in the second stage of LIGO project if it is limited by thermoelastic noise in the coating only.
Recent researches show that the fluctuations of the dielectric mirrors coating thickness can introduce a substantial part of the future laser gravitational-wave antennae total noise budget. These fluctuations are especially large in the high-reflectivity end mirrors of the Fabry-Perot cavities which are being used in the laser gravitational-wave antennae. We show here that the influence of these fluctuations can be substantially decreased by using additional short Fabry-Perot cavities, tuned in anti-resonance instead of the end mirrors.
Current interferometric gravitational wave detectors use test masses with mirror coatings formed from multiple layers of dielectric materials, most commonly alternating layers of SiO2 (silica) and Ta2O5 (tantala). However, mechanical loss in the Ta2O5/SiO2 coatings may limit the design sensitivity for advanced detectors. We have investigated sources of mechanical loss in the Ta2O5/SiO2 coatings, including loss associated with the coating-substrate interface, with the coating-layer interfaces, and with the bulk material. Our results indicate that the loss is associated with the bulk coating mat…
Thermal noise of a mirror is one of the limiting noise sources in the high precision measurement such as gravitational-wave detection, and the modeling of thermal noise has been developed and refined over a decade. In this paper, we present a derivation of coating thermal noise of a finite-size cylindrical mirror based on the fluctuation-dissipation theorem. The result agrees to a previous result with an infinite-size mirror in the limit of large thickness, and also agrees to an independent result based on the mode expansion with a thin-mirror approximation. Our study will play an important ro…
Interferometric gravitational wave detectors use mirrors whose substrates are formed from materials of low intrinsic mechanical dissipation. The two most likely choices for the test masses in future advanced detectors are fused silica or sapphire. These test masses must be coated to form mirrors, highly reflecting at 1064nm. We have measured the excess mechanical losses associated with adding dielectric coatings to substrates of fused silica and calculate the effect of the excess loss on the thermal noise in an advanced interferometer.
Thermal fluctuations in the coatings used to make high-reflectors are becoming significant noise sources in precision optical measurements and are particularly relevant to advanced gravitational wave detectors. There are two recognized sources of coating thermal noise, mechanical loss and thermal dissipation. Thermal dissipation causes thermal fluctuations in the coating which produce noise via the thermo-elastic and thermo-refractive mechanisms. We treat these mechanisms coherently, give a correction for finite coating thickness, and evaluate the implications for Advanced LIGO.
We calculate the thermal noise in half-infinite mirrors containing a layer of arbitrary thickness and depth made of excessively lossy material but with the same elastic material properties as the substrate. For the special case of a thin lossy layer on the surface of the mirror, the excess noise scales as the ratio of the coating loss to the substrate loss and as the ratio of the coating thickness to the laser beam spot size. Assuming a silica substrate with a loss function of 3x10-8 the coating loss must be less than 3x10-5 for a 6 cm spot size and a 7 micrometers thick coating to avoid incre…
Mirror thermal noise is and will remain one of the main limitations to the sensitivity of gravitational wave detectors based on laser interferometers. We report about projected mirror thermal noise due to losses in the mirror coatings and substrates. The evaluation includes all kind of thermal noises presently known. Several of the envisaged substrate and coating materials are considered. The results for mirrors operated at room temperature and at cryogenic temperature are reported.
The sensitivity of kilometer-scale terrestrial gravitational wave interferometers is limited by mirror coating thermal noise. We explore the effect of folding the arm cavities of such interferometers. While simple folding alone does not reduce the mirror coating thermal noise, it makes the folding mirror the critical mirror, opening up a variety of design and upgrade options.
We report on thermal noise from the internal friction of dielectric coatings made from alternating layers of Ta2O5 and SiO2 deposited on fused silica substrates. We present calculations of the thermal noise in gravitational wave interferometers due to optical coatings, when the material properties of the coating are different from those of the substrate and the mechanical loss angle in the coating is anisotropic. The loss angle in the coatings for strains parallel to the substrate surface was determined from ringdown experiments. We measured the mechanical quality factor of three fused silica …
We report the first high-precision interferometer using large sapphire mirrors, and we present the first direct, broadband measurements of the fundamental thermal noise in these mirrors. Our results agree well with the thermoelastic-damping noise predictions of Braginsky, et al. [Phys. Lett. A 264, 1(1999)] and Cerdonio, et al.[Phys. Rev. D 63, 082003 (2001)], which have been used to predict the astrophysical reach of advanced interferometric gravitational wave detectors.
Optical multilayer coatings of high-reflective mirrors significantly determine the properties of Fabry-Perot resonators. Thermal (Brownian) noise in these coatings produce excess phase noise which can seriously degrade the sensitivity of high-precision measurements with these cavities, in particular in laser gravitational-wave antennas (for example project LIGO), where at the current stage it is one of the main limiting factors. We present a method to calculate this effect accurately and analyze different strategies to diminish it by optimizing the coating. Traditionally this noise is calculat…
The French-Italian interferometric gravitational wave detector VIRGO is currently being commissioned. Its principal instrument is a Michelson laser interferometer with 3 km long optical cavities in the arms and a power-recycling mirror. The interferometer resides in an ultra-high vacuum system and the mirrors are suspended from multistage pendulums for seismic isolation. This type of laser interferometer reaches its maximum sensitivity only when the optical setup is held actively very accurately at a defined operating point: control systems using the precise interferometer signals stabilise th…
Thermodynamical fluctuations of temperature in mirrors may produce surface fluctuations not only through thermal expansion in mirror body but also through thermal expansion in mirror coating. We analyze the last "surface" effect which can be larger than the first "volume" one due to larger thermal expansion coefficient of coating material and smaller effective volume. In particular, these fluctuations may be important in laser interferometric gravitational antennae.
Thermoelastic noise will be the most significant noise source in advanced-LIGO interferometers with sapphire test masses. The standard plan for advanced-LIGO has optimized the optics, within the framework of conventional mirrors, to reduce thermoelastic noise. Recently, we and our collaborators have proposed going beyond the bounds of traditional optics to increase the effective beam spot size and thus lower thermoelastic noise. One particular proposal for mirror shapes (``Mexican-hat mirrors'') yields the class of ``mesa'' beams. In this paper, we outline a general procedure for analyzing lig…
We analyze the Brownian thermal noise of a multi-layer dielectric coating, used in high-precision optical measurements including interferometric gravitational-wave detectors. We assume the coating material to be isotropic, and therefore study thermal noises arising from shear and bulk losses of the coating materials. We show that coating noise arises not only from layer thickness fluctuations, but also from fluctuations of the interface between the coating and substrate, driven by internal fluctuating stresses of the coating. In addition, the non-zero photoeleastic coefficients of the thin fil…
We propose a class of displacement- and laser-noise free gravitational-wave-interferometer configurations, which does not sense non-geodesic mirror motions and laser noises, but provides non-vanishing gravitational-wave signal. Our interferometer consists of 4 mirrors and 2 beamsplitters, which form 4 Mach-Zehnder interferometers. By contrast to previous works, no composite mirrors are required. Each mirror in our configuration is sensed redundantly, by at least two pairs of incident and reflected beams. Displacement- and laser-noise free detection is achieved when output signals from these 4 …
Cryogenic Mechanical Loss of GaAs/AlGaAs Crystalline Coatings
Syracuse University（雪城大学）；Cardiff University（卡迪夫大学）；Hobart William Smith Colleges（霍巴特威廉史密斯学院）；California Institute of Technology（加州理工学院）；University of Arizona（亚利桑那大学）
In this paper we study several means of compensating for thermal lensing which, otherwise, should be a source of concern for future upgrades of interferometric detectors of gravitational waves. The methods we develop are based on the principle of heating the cold parts of the mirrors. We find that thermal compensation can help a lot but can not do miracles. It seems finally that the best strategy for future upgrades (``advanced configurations'') is maybe to use thermal compensation together with another substrate materials than Silica, for example Sapphire.
The photo-thermal transfer function from absorbed power incident on a dielectric mirror to the effective mirror position is calculated using the coating design as input. The effect is found to change in amplitude and sign for frequencies corresponding to diffusion length comparable to the coating thickness. Transfer functions are calculated for the $Ti$-doped ${\rm Ta_2O_5:SiO_2}$ coating used in Advanced LIGO and for a crystalline ${\rm Al_xGa_{1-x}As}$ coating. The shape of the transfer function at high frequencies is shown to be a sensitive indicator of the effective absorption depth, provi…
In second-generation, ground-based interferometric gravitational-wave detectors such as Advanced LIGO, the dominant noise at frequencies $f \sim 40$ Hz to $\sim 200$ Hz is expected to be due to thermal fluctuations in the mirrors' substrates and coatings which induce random fluctuations in the shape of the mirror face. The laser-light beam averages over these fluctuations; the larger the beam and the flatter its light-power distribution, the better the averaging and the lower the resulting thermal noise. In semi-infinite mirrors, scaling laws for the influence of beam shape on the four dominan…
In laser gravitational waves detectors optical loss restricts sensitivity. We discuss polarization scattering as one more possible mechanism of optical losses. Circulated inside interferometer light is polarized and after reflection its plane of polarization can turn a little due to reflecting coating of mirror can have slightly different refraction index along axes $x,\, y$ in plane of mirror surface (optical anisotropy). This anisotropy can be produced during manufacture of coating (elasto-optic effect). This orthogonal polarized light, enhanced in cavity, produces polarization optical loss.…
We have measured the photothermal effect in a single cross-polarized interferometer at audio frequencies (5 Hz - 4 kHz). In a Fabry-Perot interferometer, light in one polarization is chopped to periodically heat the interferometer mirrors, while light in the orthogonal polarization measures the mirror length changes. Tests of a polished solid metal mirror show good agreement with relevant proposed theories by Braginsky et al. ["Thermodynamical fluctuations and photo-thermal shot noise in gravitational wave antennae," Physics Letters A 264, 1-10 (1999)] and Cerdonio et al. ["Thermoelastic effec…
In this paper, an analytical solution to the problem of optimal dielectric coating design of mirrors for gravitational wave detectors is found. The technique used to solve this problem is based on Herpin's equivalent layers, which provide a simple, constructive, and analytical solution. The performance of the Herpin-type design exceeds that of the periodic design and is almost equal to the performance of the numerical, non-constructive optimized design obtained by brute force. Note that the existence of explicit analytic constructive solutions of a constrained optimization problem is not guara…
The sensitivity of current and planned gravitational wave interferometric detectors is limited, in the most critical frequency region around 100 Hz, by a combination of quantum noise and thermal noise. The latter is dominated by Brownian noise: thermal motion originating from the elastic energy dissipation in the dielectric coatings used in the interferometer mirrors. The energy dissipation is a material property characterized by the mechanical loss angle. We have identified mixtures of titanium dioxide (TiO$_2$) and germanium dioxide (GeO$_2$) that show internal dissipations at a level of 1 $…
We report the results of a recent search for the lowest value of thermal noise that can be achieved in LIGO by changing the shape of mirrors, while fixing the mirror radius and maintaining a low diffractional loss. The result of this minimization is a beam with thermal noise a factor of 2.32 (in power) lower than previously considered Mesa Beams and a factor of 5.45 (in power) lower than the Gaussian beams employed in the current baseline design. Mirrors that confine these beams have been found to be roughly conical in shape, with an average slope approximately equal to the mirror radius divid…
Beyond Bragg-Mirrors for Gravitational Wave Telescopes: A Fabrication Tolerant Hybrid Metasurface-Bragg Mirror Design
Friedrich Schiller University（弗里德里希·席勒大学）；Technische Universität Braunschweig（布伦瑞克工业大学）；Institut für Halbleitertechnik, Technische Universität Braunschweig（布伦瑞克工业大学半导体技术研究所）；Fraunhofer-Institute for Applied Optics and Precision Engineering IOF（弗劳恩霍夫应用光学和精密工程研究所）；Physikalisch-Technische Bundesanstalt（德国联邦物理技术研究院）
By mapping the signal-recycling (SR) optical configuration to a three-mirror cavity, and then to a single detuned cavity, we express SR optomechanical dynamics, input--output relation and noise spectral density in terms of only three characteristic parameters: the (free) optical resonant frequency and decay time of the entire interferometer, and the laser power circulating in arm cavities. These parameters, and therefore the properties of the interferometer, are invariant under an appropriate scaling of SR-mirror reflectivity, SR detuning, arm-cavity storage time and input power at beamsplitte…
Advanced LIGO's present baseline design uses arm cavities with Gaussian light beams supported by spherical mirrors. Because Gaussian beams have large intensity gradients in regions of high intensity, they average poorly over fluctuating bumps and valleys on the mirror surfaces, caused by random thermal fluctuations (thermoelastic noise). Flat-topped light beams (mesa beams) are being considered as an alternative because they average over the thermoelastic fluctuations much more effectively. However, the proposed mesa beams are supported by nearly flat mirrors, which experience a very serious t…
Experimental Realization of Optimized Ternary Mirror Coatings
Università del Sannio（桑尼奥大学）；INFN Sezione di Napoli Gruppo Collegato di Salerno（意大利国家核物理研究院那不勒斯分部萨莱诺协作组）；Laboratoire des Matériaux Avancés - IP2I, CNRS, Université Claude Bernard Lyon 1（先进材料实验室-IP2I，法国国家科学研究中心，里昂第一大学）；Massachusetts Institute of Technology（麻省理工学院）；Università di Salerno（萨莱诺大学）；Università di Roma Tre（罗马第三大学）
In order to achieve full detection sensitivity at low frequencies, the mirrors of interferometric gravitational wave detectors must be isolated from seismic noise. The VIRGO vibration isolator, called 'superattenuator', is fully effective at frequencies above 4 Hz. Nevertheless, the residual motion of the mirror at the mechanical resonant frequencies of the system are too large for the interferometer locking system and must be damped. A multidimensional feedback system, using inertial sensors and digital processing, has been designed for this purpose. An experimental procedure for determining …
Motivated by the optical-bar scheme of Braginsky, Gorodetsky and Khalili, we propose to add to a high power detuned signal-recycling interferometer a local readout scheme which measures the motion of the arm-cavity front mirror. At low frequencies this mirror moves together with the arm-cavity end mirror, under the influence of gravitational waves. This scheme improves the low-frequency quantum-noise-limited sensitivity of optical-spring interferometers significantly and can be considered as a incorporation of the optical-bar scheme into currently planned second-generation interferometers. On …
We show that quantum noise in very sensitive interferometric measurements such as gravitational-waves detectors can be drastically modified by quantum feedback. We present a new scheme based on active control to lock the motion of a mirror to a reference mirror at the quantum level. This simple technique allows to reduce quantum effects of radiation pressure and to greatly enhance the sensitivity of the detection.
We compare a conventional Mach-Zehnder light-pulse atom interferometer based on diffractive mirrors with one that uses specular reflection. In contrast to diffractive mirrors that generate a symmetric configuration, specular mirrors realized, for example, by evanescent fields lead under the influence of gravity to an asymmetric geometry. In such an arrangement the interferometer phase contains nonrelativistic signatures of proper time.
The sensitivity in interferometric measurements such as gravitational-wave detectors is ultimately limited by quantum noise of light. We discuss the use of feedback mechanisms to reduce the quantum effects of radiation pressure. Recent experiments have shown that it is possible to reduce the thermal motion of a mirror by cold damping. The mirror motion is measured with an optomechanical sensor based on a high-finesse cavity, and reduced by a feedback loop. We show that this technique can be extended to lock the mirror at the quantum level. In gravitational-waves interferometers with Fabry-Pero…
We have measured the mechanical loss of a dielectric multilayer reflective coating (ion-beam sputtered SiO$_2$ and Ta$_2$O$_5$) in cooled mirrors. The loss was nearly independent of the temperature (4 K $\sim$ 300 K), frequency, optical loss, and stress caused by the coating, and the details of the manufacturing processes. The loss angle was $(4 \sim 6) \times 10^{-4}$. The temperature independence of this loss implies that the amplitude of the coating thermal noise, which is a severe limit in any precise measurement, is proportional to the square root of the temperature. Sapphire mirrors at 2…
A fundamental limit to the sensitivity of optical interferometers is imposed by Brownian thermal fluctuations of the mirrors' surfaces. This thermal noise can be reduced by using larger beams which "average out" the random fluctuations of the surfaces. It has been proposed previously that wider, higher-order Laguerre-Gaussian modes can be used to exploit this effect. In this article, we show that susceptibility to spatial imperfections of the mirrors' surfaces limits the effectiveness of this approach in interferometers used for gravitational-wave detection. Possible methods of reducing this s…
The displacement- and frequency-noise-free interferometer (DFI) is a multiple laser interferometer array for gravitational wave detection free from both the displacement noise of optics and laser frequency noise. So far, partial experimental demonstrations of DFI have been done in 2-D table top experiments. In this paper, we report the complete demonstration of a 3-D DFI. The DFI consists of four Mach-Zehnder interferometers with four mirrors and two beamsplitters. The displacement noises both of mirrors and beamsplitters were suppressed by up to 40 dB. The non-vanishing DFI response to a grav…
Laser interferometer detectors are now widely used in an attempt to detect gravitational waves (gw). The interaction of the gw with the light circulating in the interferometer is usually explained in terms of the motion of the "free" mirrors that form the interferometer arms. It is however instructive to show that the same result can be obtained by simply calculating the propagation of an electromagnetic plane wave between "free mirrors" in the curved space-time induced by the gw. One finds that the plane wave acquires frequency modulation sidebands at the gw frequency, as would be expected fr…
We report on the current status of CLIO (Cryogenic Laser Interferometer Observatory), which is a prototype interferometer for LCGT (Large Scale Cryogenic Gravitational-Wave Telescope). LCGT is a Japanese next-generation interferometric gravitational wave detector featuring the use of cryogenic mirrors and a quiet underground site. The main purpose of CLIO is to demonstrate a reduction of the mirror thermal noise by cooling the sapphire mirrors. CLIO is located in an underground site of the Kamioka mine, 1000 m deep from the mountain top, to verify its advantages. After a few years of commissio…
Reduction of coating thermal noise is a key issue in precise measurements with an optical interferometer. A good example of such a measurement device is a gravitational-wave detector, where each mirror is coated by a few tens of quarter-wavelength dielectric layers to achieve high reflectivity while the thermal-noise level increases with the number of layers. One way to realize the reduction of coating thermal noise, recently proposed by Khalili, is the mechanical separation of the first few layers from the rest so that a major part of the fluctuations contributes only little to the phase shif…
Reduction of thermal noise in dielectric mirror coatings is a key issue for the sensitivity improvement in second and third generation interferometric gravitational wave detectors. Replacing an end mirror of the interferometer by an anti-resonant cavity (a so-called Khalili cavity) has been proposed to realize the reduction of the overall thermal noise level. In this article we show that the use of a Khalili etalon, which requires less hardware than a Khalili cavity, yields still a significant reduction of thermal noise. We identify the optimum distribution of coating layers on the front and r…
We present an approximate analysis of a nonlinear effect of parametric oscillatory instability in FP interferometer. The basis for this effect is the excitation of the additional (Stokes) optical mode and of the mirror's elastic mode when the optical energy stored in the FP resonator main mode exceeds the certain threshold. This effect is undesirable in laser gravitational wave antennae because it may create a specific upper limit for the value of energy stored in FP resonator. In order to avoid it the detailed analysis of the mirror's elastic modes and FP resonator optical modes structure is …
In the baseline design for advanced LIGO interferometers, the most serious noise source is tiny, dynamically fluctuating bumps and valleys on the faces of the arm-cavity mirrors, caused by random flow of heat in the mirrors' sapphire substrates: so-called "thermoelastic noise". We propose replacing the interferometers' baseline arm-cavity light beams, which have Gaussian-shaped intensity profiles, by beams with mesa-shaped profiles that are flat in their central ~7 cm of radius, and that then fall toward zero as quickly as is allowed by diffraction in LIGO's 4 km arms. The mesa beams average t…
For further gravitational wave (GW) detections, it is significant to invent a technique to reduce all kinds of mirror displacement noise dominant at low frequencies for ground-based detectors. The neutron displacement-noise-free interferometer (DFI) is one of the tools to reduce all the mirror displacement noise at lower frequencies. In this paper, we describe a further simplified configuration of a neutron DFI in terms of neutron incidence direction. In the new configuration, neutrons enter the interferometer with unidirectional incidence at four speeds as opposed to two bidirectional inciden…
The improvement of sensitivity to gravitational waves (GWs) at lower frequencies is still challenging on account of displacement noise. One of the solutions is the neutron displacement-noise-free interferometer (DFI). We focus on a simplification of the detector configuration by taking advantage of the ability to adjust the neutron speed depending on the configuration. The new configuration consists of two beamsplitters and two mirrors, which constitute a single Mach-Zehnder interferometer (MZI). It is simpler than the configuration with two MZIs in previous research. All displacement noise of…
Using the force-susceptibility formalism of linear quantum measurements, we study the dynamics of signal recycled interferometers, such as LIGO-II. We show that, although the antisymmetric mode of motion of the four arm-cavity mirrors is originally described by a free mass, when the signal-recycling mirror is added to the interferometer, the radiation-pressure force not only disturbs the motion of that ``free mass'' randomly due to quantum fluctuations, but also and more fundamentally, makes it respond to forces as though it were connected to a spring with a specific optical-mechanical rigidit…
This thesis presents a collection of different researches on non-standard optics in view of enhancing the performances of the Advanced Gravitational waves interferometric detectors, where the thermal noise of the test masses is expected to be a limiting factor for their sensitivity. We provide a quantitative analysis of the impact of non-Gaussian beams on different kinds of thermal noises. We developed the theory of mesa beam, in view of a future implementation in advanced GW interferometers of the mesa beam idea, focusing on the analytical derivation of the quantities (i.e. beam width, diverg…
Increasing requirements in the sensitivity of interferometric measurements is a common feature of several research fields, from gravitational wave detection to quantum optics. This motivates refined studies of high reflectivity mirrors and of noise sources that are tightly related to their structure. In this work we present an experimental characterization of photothermal and thermo-refractive effects in high reflectivity mirrors, i.e., of the variations in the position of their effective reflection plane due to weak residual power absorption. The measurements are performed by modulating the i…
KAGRA is a 3-km cryogenic interferometric gravitational wave telescope located at an underground site in Japan. In order to achieve its target sensitivity, the relative positions of the mirrors of the interferometer must be finely adjusted with attached actuators. We have developed a model to simulate the length control loops of the KAGRA interferometer with realistic suspension responses and various noises for mirror actuation. Using our model, we have designed the actuation parameters to have sufficient force range to acquire lock as well as to control all the length degrees of freedom witho…
We show that back-action noise in interferometric measurements such as gravitational-waves detectors can be completely suppressed by a local control of mirrors motion. An optomechanical sensor with an optimized measurement strategy is used to monitor mirror displacements. A feedback loop then eliminates radiation-pressure effects without adding noise. This very efficient technique leads to an increased sensitivity for the interferometric measurement, which becomes only limited by phase noise. Back-action cancellation is furthermore insensitive to losses in the interferometer.
In interferometric cryogenic gravitational wave detectors, there are plans to cool mirrors and their suspension systems (payloads) in order to reduce thermal noise, that is, one of the fundamental noise sources. Because of the large payload masses (several hundred kg in total) and their thermal isolation, a cooling time of several months is required. Our calculation shows that a high-emissivity coating (e.g. a diamond-like carbon (DLC) coating) can reduce the cooling time effectively by enhancing radiation heat transfer. Here, we have experimentally verified the effect of the DLC coating on th…
As part of the upgrade program of the Advanced Virgo interferometer, the installation of new instrumented baffles surrounding the main test masses is foreseen. As a demonstrator, and to validate the technology, the existing baffle in the area of the input mode cleaner end-mirror will be first replaced by a baffle equipped with photodiodes. This paper presents detailed simulations of the light distribution on the input mode cleaner baffle, with the aim to determine the light exposure of the photodiodes under different scenarios of the interferometer operation.
